Spin Bike 300SB User Manual For all service enquiries go to www.evofitness.net.
CONTENTS SAFETY & MAINTENANCE INSTRUCTIONS……………….…….…….1 GENERAL KNOWLEDGE …………....………...……..………..…………..2 ASSEMBLY INSTRUCTIONS……..……………………….…….………….
SAFETY & MAINTENANCE INSTRUCTIONS 1. Once assembled fully, please ensure that all parts such as bolts, nuts and washers are positioned and tightened correctly. 2. Inspect the safety chain guard of the bike regularly to ensure that all screws and bolts are tight. 3. Always inspect the seat post, seat slider, pedals and handlebar to make sure they are in safe and stable position before using the bike. 4. Do not wear loose clothing 5. Running or aerobic shoes are required when using the bike.
GENERAL KNOWLEDGE 1. This cycle should always be placed on a level surface for use. You may raise or lower the bike by adjusting the four leveling bolts (16). 2. Adjust Seat (22) to a suitable position by adjusting Seat Sliders (3) and Seat Post (2). And please adjust height of Handlebar (4) according to your body size. 3. Set the correct resistance by Adjusting Knob (11) please set a right resistance according to your requirement. 4. The drive mode of the equipment is bi-directive drive.
Item NO.
42 43 Clamp Brake Holder Flat washer 44 6001 45 6004 46 47 48 49 608 C shape axes snap spring C shape axes snap spring Spring nut Cross big flat head tapping screw Hexagon flange nut M12 nut cap Hexagon flange nut Cross sinking screw Hexagon thin nut M12 Hexagon flange nut Nylon nut Nylon nut Flat mat GB/T97.2 10 Flat mat GBT97.
Small exploded diagram
Installation Step 1: Assemble base of bike Attach the front stabilizer (8) and rear stabilizer (7) to the main frame (1) with inner hexagon flat round head M10x25L (34), flat washer φ20*φ10*1.5T (33) (4 Pcs / item) using tools. Step 2: Assemble left and right pedals. Connect the right and left pedals (35) to their appropriate crank arms, then tighten using open spanner 15#.
Step 3: Assemble the adjustable handlebar post Loosen the adjusting knob (23), and slide the handlebar post (4) into the handlebar post housing on the main frame, then tighten the adjusting knob (23). Step 4: Assemble the handlebar Assemble the handlebar (5) onto the handlebar post and tighten it with adjusting handle (77) and flat washer (76).
Step 5: Assemble the seat post Loosen the adjusting knob (23) and slide the seat post (2) to the seat post housing on the main frame, then tighten the adjusting knob (23). Step 6: Assemble the seat. Loosen the adjusting knob (23) and slide the seat slider (3) into the seat post (2), then tighten the adjusting knob (23) and fix the seat (22) to the seat slider (3).
Step 7: Assemble water bottle cage and water bottle Tighten the water bottle holder (72) to main frame (1) using enclosed tools and put in the water bottle (71). Step 8: Assemble the computer Tighten the computer sensor base (78) under the water bottle holder, facing the flywheel. Attach the computer shelf (75) and put in the computer (74).
Step 9: When installation is finished, please carefully re-tighten all the screws and nuts. Note 1. Inspect all the nuts, nut caps and pedals regularly and inspect the equipment periodically. If you find any defective parts, replace them immediately. 2. Please pay attention to the friction brake pad (41) as over time this part may wear or become worn. If this occurs please replace the part. Use silicone spray to reduce friction.
3. Please inspect the pedals before use to ensure they are tight. 4. Please adjust the hexagon nut by using the open spanner if the seat (22) is loose. 5.
Console instruction 1. MODE Speed, time, distance, temperature, pulse, average speed, max speed, total distance and scan. 2. SET a) RESTORATION: restoration of distance, time, average speed and max speed. b) Data adjustment Speed unit, wheel perimeter, time setup 1. Clear the data, KM/H will flash, enter speed unit. 2. Press SET to switch between KM/H and M/H, Press “MODE” to confirm and exit; 3.
Start the Spin Bike Computer After installation is complete of every mode according to the instructions and all data is set-up, then you can use the spin bike computer. 1. Before operation, clear all the previous data, this is when the degree is zero, press “SET” for two seconds, clear the data of “DST”, “RTM”, “AVS”, “RES” and “ MAX” for zero, then enter “SCAN”. 2. Once you start to cycle the computer will immediately start. If there is no signal, the icon “ magnet to make sure it is installed correctly.
2. Press “MODE” to change the display, see diagram Q Diagram Q a) Top data is current speed: 20.2KM/H b) Bottom is riding speed: 5.6KM. 3. Press “MODE” key to change display, see diagram R. Picture R a) The top data is current speed b) Bottom data is riding time, if it exceeds six seconds with no signal, it will stop calculating the time. 4. Press “MODE” to change the display, see diagram S, Diagram S a) Top data is current speed b) The bottom data is current heart beat rate.
5. Press “MODE” key to change display, see diagram T, Diagram T a) The top data is the current speed b) The bottom data is the temperature e.g.: 24 degrees. 6. Press “MODE” key to change the display, see diagram U, Diagram U a) Finger symbol shows current speed, AVS expresses average speed, e.g. the average speed from the start of riding to the current time: 10.2KM/H. RES shows relative speed, e.g. this is your AVS speed and current speed combined: 10.0KM/H. 7.
Common malfunction solutions Malfunction sign Computer can not receive information Reason Solution Installation location is not correct Reinstall according requirement. Sensor or computer battery Installation error Install battery correctly or replace with new battery Speed, distance display not correct Wheel perimeter incorrectly set Speed display confusion Outer electromagnetism signal interfering. to Reset wheel perimeter Avoid the interfering source. E.g. other electrical interference.
