Installation Sheet

28
Evo America, LLC 20360 SW Avery Ct., Tualatin, OR 97062 USA
Phone [phone] | Fax [phone] | evoamerica.com | [e-mail]
IGNITOR CHECK
IMPORTANT: Turn gas off at tank and place both control knobs in Off position. Press ignitor button and hold for 2-3 seconds. A “Click”
should be heard and a spark seen each time between collector box and electrode. Be sure to check both collector boxes and both electrodes.
Be certain that your battery is clean and operating with a suffi cient charge.
MATCH LIGHTING YOUR GRILL
1 • Be sure gas control knobs are in the Off position.
2 • Be sure grill cook surface is properly installed over burner skirt.
3 • Turn gas on at tank.
4 • Place long-stem match into fl ame viewing portal (see diagram).
5 • Push in and turn either knob on the control panel to the Lite position. Be sure burner lights and
stays lit.
6 • After burner lights, adjust knob to High or Low settings. Push in and turn other knob in order to
light opposite burner.
7 • Warning: If burner(s) do not light, turn both control knobs to the Off position.
After waiting 4 minutes, start again.
CHECKING BURNER FLAMES
Light burner using either ignitor or match. Rotate control knobs from High to Low while viewing fl ame
through the fl ame portals. You should see a smaller fl ame in the Low position from that seen in the High
position. Always check fl ame prior to each use.
Notice: Flame portals are conveniently located parallel to each three legs and directly below the cooking surface to provide fl ame monitoring
from three positions around grill.
TURNING YOUR GRILL OFF
To turn grill off , turn both control knobs to off position. Completely close tank valve on LP gas tank
(clockwise).
CHECKING VALVES
IMPORTANT: Turn gas off at tank and place both control knobs in Off position.
Both control knobs lock into Off position. To check valves, fi rst push-in knobs and release them. Turn knobs
from Off to Low position. You will notice a slight detent between Off and Low indicating the High position. Knobs should spring back slightly
when released. If knobs do not spring back, remove knob from valve stem by pulling outward and checking for obstructions under knob and
around valve stem. If no obstruction is found and knob will not spring back, then replace valve before using grill.
QUICK GUIDE FOR CLEANING AND CARING FOR EVO GRILL
The exposed surfaces of this grill are made from two types of metal; stainless steel, and a mild grade steel cooking surface.
Rust on Stainless Steel
Stainless steel is metallurgically incapable of rusting. Any rust that forms is the result of iron particles from an outside source. If you notice rust
spots, you can eliminate them with regular cleaning as described above.
What To Avoid On Stainless Steel
Bleaches containing hypochlorite will cause pitting and staining.
Silver dip cleaners contain acids that leave a permanent stain.
Acidic foods, when left for a prolonged time, can cause pitting and staining.
Examples are citrus fruits, vinegar, mustard, and pickles.
Cleaning and Maintaining the Cooking Surface
If not properly maintained, the cook surface will accumulate heavy plaque from charred food debris. This issue is easily resolved with routine
cleaning between preparations, and gently scraping the cook surface with a metal spatula to remove the majority of surface debris. The cleaning
kit contains a professional 3M-brand grill screen handle and pad. Place the pad underneath the grill handle. Use a small amount of vegetable oil
on the cook surface and scrub in a circular motion. Take care not to remove the majority of dark seasoning. When fi nished scrubbing, wipe the
surface down with a paper towel or cotton terrycloth. The desired cooking surface should be dark in color, lightly oiled, and smooth.
BEFORE COOKING ON YOUR GRILL
Your Evo cook surface has been carefully prepared and fi nished at the factory to provide the best possible cooking surface, however for an
HIGH Flame
LO Flame
Insert Match
Here
Cook Surface Raised For
Illustration Purposes Only