™ Version 1.
EVIL® Pimp Kit™ Operator’s Manual EVIL® Pimp Kit™ Operator’s Manual Table of Contents Statement of Liability PAINTBALL SAFETY RULES 4 COMPRESSED GAS/NITROGEN 6 OPERATING INSTRUCTIONS 8 SPECIFICATIONS 10 VELOCITY ADJUSTMENT 11 PARTS/DIAGRAMS ™ 12 WARRANTY INFORMATION CARD This EVIL® Pimp Kit ™ semi-automatic paintball marker is surrendered by Pursuit Marketing, Inc. (PMI, Inc.
Paintball Basic Safety Rules Paintball Basic Safety Rules Read this operator’s manual completely before loading, pressurizing, or operating the EVIL® Pimp Kit™ Paintball Marker. PAINTBALL MARKERS ARE NOT TOYS. MISUSE MAY CAUSE SERIOUS INJURY OR DEATH. EYE PROTECTION DESIGNED FOR PAINTBALL USE MUST BE WORN BY THE USER AND ANY PERSON WITHIN RANGE. READ THIS OPERATOR’S MANUAL COMPLETELY BEFORE LOADING, PRESSURIZING, OR OPERATING THE EVIL® PIMP KIT™ PAINTBALL MARKER.
Compressed Gas/Air Compressed Gas/Air The EVIL® Pimp Kit ™ paintball marker may be powered by regulated compressed air, or regulated nitrogen only. Operating Pressure and Input Pressure • Operating pressure range: 150-400 psi. • Respirator Low Pressure Regulator (LPR) Range: 100-150 psi. • Recommended maximum input pressure is 175 p.s.i. into the marker from the LPR. • Exceeding 175 psi into marker can damage solenoid and void warranty. • Maximum inlet to Detonator regulator 1000 psi.
Operating the EVIL® Pimp Kit™ Marker EVERY PERSON WITHIN RANGE OF AN AREA WHERE ANY PAINTBALL MARKER IS IN USE MUST WEAR PROTECTIVE GOGGLES AND HEADGEAR SPECIFICALLY DESIGNED FOR PAINTBALL. First time users follow instructions carefully until familiar with EVIL® Pimp Kit™ 1 Attach threaded barrel firmly to marker. 2 Install barrel blocking device (barrel condom, bag, sock or plug) firmly into or onto barrel. 3 Attach empty loader into feed tube.
EVIL® Pimp Kit™ Specifications Velocity Adjustment Action: Semi-automatic Length: 11 inches without barrel Weight: 3.45 lbs. Height: 9.5 inches Barrel: Two piece construction with Impulse threads. Mid-grade .689 back. EVIL® Pipe™ front anodized to match can be used interchangeably with EVIL® Pipe™ backs. .689 backs available in high polish or matte finish Paintballs: For use only with standard “.68 caliber” (.
EVIL® Pimp Kit™ Parts Location EVIL® Pimp Kit™ Body Diagram 54 1 56 55 5 Shortstack Feed Tube Dual Ball Detents 2 6 4 Venturi Style Quick Release Delrin Bolt 57 58 60 2 2 3 59 7 26 8 Electronic Anti-Chop Eye 21 Ram 9 Evil Respirator Low Pressure Regulator (LPR) 22 24 23 20 27 18 12 85 19 84 39 11 11 15 15 86 30 10 12 13 25 31 17 16 32 41 Low Pressure Gauge 34 31 34 33 28 28 On/Off Safety Switch Adjustable Double Trigger 35 35 28 29 36 42 Indicator LED
EVIL® Pimp Kit™ Ram & Reg Diagram 61 65 62 63 63 68 67 66 69 62 64 ™ 70 73 71 76 72 83 79 74 56515 56517 56534A 10608 56532 57994 56533A 56531A 57643 56530SB 57625 57490SB 57497 10257 57491SB 40920 57489 10361 57487B 10265 57608 57488 57486 47028 11442 57747 56543 56517 Tape Here 14 Pimp Kit™ Bolt Pin Pimp Kit™ Bolt Pin Spring Pimp Kit™ Hammer 011-70 Urethane O-ring Pimp Kit™ Ram Bumper 018-70 Urethane O-ring Pimp Kit™ Ram Body Pimp Kit™ Ram Piston 009-70 Urethane O-ring Pimp Kit™ Ram Cap
EVIL® Pimp Kit™ Warranty Registration Please fill out entirely this EVIL® Pimp Kit ™ Warranty Registration form including the checklist and mail it to: Pursuit Marketing, Inc., 55 Howard Ave, Des Plaines, IL 60018 USA. Save your original sales purchase receipt or packing slip. A copy must accompany the marker when warranty repairs are sought. Consult owners manual for warranty information and instructions on obtaining repair service.
Parts Kit 1. 20/70 Buna O-Ring 2. 21/70 Buna O-Ring 3. 22/70 Buna O-Ring 4. 3/32 long arm 5. 3/16 short arm 6. 5/64 short arm 7. 1/8 short arm 8. Regulator Reg Seat 9. Evil Pus 10. 4 Ball Detents 11. Barrel Centering O-ring 19/70 U 12. Evil Barrel Condom 40920 40921 40922 42033 42028 42038 42026 57486 62221 10160 10265 61228 ™ Trigger Adjustment Remove Trigger Frame from the marker. You will have to disconnect the Solenoid to completely remove the Trigger Frame.
EVIL® Pimp Kit™ Bolt Removal EVIL® Pimp Kit™ Eye & Ball Detent Replacement The EVIL® Pimp Kit ™ stock delrin bolt needs no maintenance. Always clean marker after every day of play. This usually does not mean a complete strip. On the contrary, most warranty calls originate from improper assembly by the operator. However, do not hesitate to call Evil HQ with questions. REMOVING BOLT UNLOCKING BOLT The ball detents will wear over time and will have to be replaced.
EVIL® Pimp Kit™ Detonator Diagram EVIL® Pimp Kit™ Detonator Maintenance EVIL® Detonator™ Service Procedures DO NOT ATTEMPT TO PERFORM MAINTENANCE PROCEDURES UNLESS QUALIFIED TO DO SO. DO NOT DISASSEMBLE MARKER UNTIL IT IS COMPLETELY DRAINED OF COMPRESSED GAS OR AIR AND ALL PAINTBALLS HAVE BEEN REMOVED. FILLING OF COMPRESSED GAS OR AIR CYLINDERS MUST BE DONE BY QUALIFIED PERSONS. DISASSEMBLY OF REGULATOR MAY VOID WARRANTY.
LPR Adjustment and Maintenance LPR Maintenance Cont. Respirator LPR Adjustment LPR Seat Seal • Always degas the marker before adjusting the LPR. If the LPR creeps or doesn’t adjust properly after greasing the internals, the seat seal may need to be replaced. • From the front of the marker, screw the cap further in (clockwise) to raise the LPR pressure. Unscrew the cap to lower the LPR pressure. • Unscrew the LPR base from the Pimp Kit.
Tuning Tuning The EVIL® Pimp Kit ™ ships from the factory already tuned, and with regular cleaning and lubrication should only require pressure regulator adjustments to set the velocity and avoid shoot down. Setting the Ghetto Board Respirator LPR Adjustment Board Adjustments-Instructions for ROF, ETS and BIP The LPR should be set at about 100-150 psi.
Troubleshooting No velocity Low velocity Troubleshooting • Bolt installed improperly. See page 16. • See page 8 for set up instructions. • Check battery. • Verify LPR is between 100-150 psi. • Increase regulator output pressure. (See page 11). • Reg pressure that is way too high (400 psi or more) can also lead to low velocity. • Grease Ram • Increase Dwell. High velocity • Decrease Detonator regulator output pressure. • Verify LPR is between 100-150 psi. • Decrease Dwell.
Warranty Repair Procedure Original Sales Purchase Receipt or Packing Slip Save your original sales purchase receipt or packing slip. A copy must accompany the marker if warranty repairs are needed. EVIL® takes pride in manufacturing high quality paintball products for many years of trouble free enjoyment. Should you experience any difficulty in operating or maintaining this paintball marker, please re-read the operator’s manual carefully. If further assistance is needed, contact PMI, Inc., at 1.800.579.
Manual #56547 EVIL® Pimp Kit ™ Paintball Markers manufactured by: Pursuit Marketing, Inc. 55 Howard Ave Des Plaines, Illinois 60018 USA Phone 1.800.579.1633 847.233.2545 www.evil-paintball.com Please visit www.EVIL-PAINTBALL.
