CT-CCV6X Intel® Atom D2000/N2000 Series COM Express™ Type 6 Module User’s Manual Version 1.0 C&T Solution Inc. 12F. -1, No.700, Zhongzheng Rd., Zhonghe Dist., New Taipei City 235, Taiwan TEL: 886-2-77317888 http://www.candtsolution.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module Table of Contents I. Preface ..................................................................................................... ５ 1.1 Disclaimer ...................................................................................... ５ 1.2 Copyright Notice ............................................................................. ５ 1.3 Trademarks Acknowledgment ........................................................ ５ II. Introduction..........
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 4.11 LPC ........................................................................................... ２８ SPI ............................................................................................ ２９ UART ........................................................................................ ２９ SMBus....................................................................................... ２９ ExpressCard ............................................
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module VII. Electrical Specification ....................................................................... ６６ 7.1 Input Power .................................................................................
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module I. Preface 1.1 Disclaimer All specifications and information in this User’s Manual are believed to be accurate and up to date. C&T Solution Inc. does not guarantee that the contents herein are complete, true, accurate or non-misleading. The information in this document is subject to change without notice and does not represent a commitment on the part of C&T Solution Inc. C&T Solution Inc.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module II. Introduction 2.1 Product Description The CT-CCV6X is a new COM (computer-on-module) Express® compact form factor (95x95mm) in embedded computing platforms. It combines the onboard Intel® Atom D2550/N2600 processor with Intel® NM10 Express chipset. The CT-CCV6X is based on the COM Express® specification and features a standardized connector layout that carries a specified set of signals.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 2.2 Specifications CPU Intel® Atom D2550 processor, 1.86GHz Intel® Atom N2600 processor, 1.6GHz Chipset Intel® NM10 PCH System Memory One 204-pin DDR3 SODIMM socket 800MHz or 1066MHz Up to 4GB at Intel® Atom D2550 processor Up to 2GB at Intel® Atom N2600 processor BIOS AMI uEFI BIOS 2MB SPI Flash ROM SSD 16GB SSD onboard TPM Trusted Platform Module compatible with TPM1.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module Integrated in chipset Intel® NM10 SATA Interface One SATA 3Gb/s port Optional second SATA PCIe Lane Two PCIex1 Lane Optional third PCIex1 Lane USB Interface Eight USB 2.0 ports Four USB 3.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 2.3 Block Diagram VGA 1-ch 24/18-bit LVDS CPU Intel D2550/N2600 DDR3 1067MH z SODIMM Up to 4GB/2GB DDI0 (DisplayPort/HDMI) DDI1 (DisplayPort/HDMI) SATAII Port1 Selection Circuit DMI Onboard 16GB SSD Intel NM10 8xUSB2.0 PCIex1 Port3 2xPCIex1 HDA 8-bit DIO Connector ROW CD Connector ROW AB Connector ROW A,B Connector ROW AB PCH SATAII Port0 TUSB 4xUSB3.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 2.4 SKU Product Number Processor PCH Features CT-CCV61 Intel Atom NM10 1xDDR3, 24-bit LVDS, 2xPCIex1, GbE, 4xUSB3.0, D2550 CT-CCV62 Intel Atom N2600 8xUSB2.0, 1xSATA, onboard 16GB SSD, TMP1.2 NM10 1xDDR3, 18-bit LVDS, 2xPCIex1, GbE, 4xUSB3.0, 8xUSB2.0, 1xSATA, onboard 16GB SSD, TMP1.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module III. Mechanical Specification 3.1 Module Dimensions The PCB size of CT-CCV6X is 95mm x 95mm, the standard COM Express compact Module size. The holes shown in the drawing below is for stacking the module with the Heat Spreader / Heat Sink and the Carrier Board. The mounting holes are 2.7mm, and the 2.5mm hardware shall be used. The position and the dimension of the holes are shown in the unit of millimeters.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module Side View and Bottom View: 3.2 Layout There is one SODIMM socket mounted on the top side of the CT-CCV6X. Two 220-pin COM Express connectors are mounted at the bottom side of the PCB.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module Top View: CN1 CN2 CN3 Bottom View: CN4 CN5 １３
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 3.3 Connectors Connector CN1 CN2 CN3 CN4 CN5 3.3.1 Description SODIMM Socket LPC Debug Port CPLD JTAGE COM™ Express connector Row A, B COM™ Express connector Row C, D LPC Debug Port: CN2 Pin Signal Pin Signal 1 GND 2 3.3V 3 LPC_AD3 4 BIOS_DIS0-L 5 LPC_AD2 6 RESET 7 LPC_AD1 8 CLOCK 9 LPC_AD0 10 FRAME 3.3.2 CPLD JTAGE: CN3 Pin Signal Pin Signal 1 3.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module Pin Row A Row B Row C Row D 1 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED) 2 GBE0_MDI3- GBE0_ACT# GND GND 3 GBE0_MDI3+ LPC_FRAME# USB_SSRX0- USB_SSTX0- 4 GBE0_LINK100# LPC_AD0 USB_SSRX0+ USB_SSTX0+ 5 GBE0_LINK1000# LPC_AD1 GND GND 6 GBE0_MDI2- LPC_AD2 USB_SSRX1- USB_SSTX1- 7 GBE0_MDI2+ LPC_AD3 USB_SSRX1+ USB_SSTX1+ 8 GBE0_LINK# LPC_DRQ0# GND GND 9 GBE0_MDI1- LPC_DRQ1# USB_SSRX2- USB_SSTX2- 10 GBE0_MD
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module Pin Row A Row B Row C Row D 39 USB4- USB5- NC DDI2_PAIR0+ 40 USB4+ USB5+ NC DDI2_PAIR0- 41 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED) 42 USB2- USB3- NC DDI2_PAIR1+ 43 USB2+ USB3+ NC DDI2_PAIR1- 44 USB_2_3_OC# USB_0_1_OC# NC DDI2_HPD 45 USB0- USB1- NC NC 46 USB0+ USB1+ NC DDI2_PAIR2+ 47 VCC_RTC EXCD1_PERST# NC DDI2_PAIR2- 48 EXCD0_PERST# EXCD1_CPPE# NC NC 49 EXCD0_CPPE# SYS_RESET# NC DDI2_PA
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module Pin Row A Row B Row C Row D 77 LVDS_VDD_EN NC NC NC 78 LVDS_A3+ NC NC NC 79 LVDS_A3- LVDS_BKLT_EN NC NC 80 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED) 81 LVDS_A_CK+ NC NC NC 82 LVDS_A_CK- NC NC NC 83 LVDS_I2C_CK LVDS_BKLT_CTRL NC NC 84 LVDS_I2C_DAT VCC_5V_SBY GND GND 85 GPI3 VCC_5V_SBY NC NC 86 NC VCC_5V_SBY NC NC 87 NC VCC_5V_SBY GND GND 88 PCIE_CK_REF0+ BIOS_DIS1# NC NC 89 PCIE_CK_R
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 3.4 Thermal Solutions There are two thermal solutions for the COM Express Module CT-CCV6X to dissipate the heat. One is by using a heat sink and the other one is by using a heat spreader. 3.4.1 Heat Sink Step 1: Connect the COM Express connectors on the module, CT-CCV6X, to the corresponding COM connectors on the Carrier Board. Make sure the four holes at the corners of CT-CCV6X module align to the corresponding pillars on the Carrier Board.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 3.4.2 Heat Spreader A heat spreader is designed for the CT-CCV6X to dissipate heat. All heat generating components are thermally conducted to the heat spreader in order to avoid hot spots. The assembly of the heat spreader with CT-CCV6X module and the Carrier board is same as the heat sink. Step 1: Connect the COM Express connectors on the module, CT-CCV6X, to the corresponding COM connectors on the Carrier Board.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module ２０
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module IV. Features & Interfaces 4.1 Processor The CT-CCV6X supports Intel® Atom D2550/N2600 processor. This 64-bit and multi-core mobile processor built on 32-nanometer process technology is based on a new micro-architecture. This architecture consists a processor and Platform Controller Hub (PCH) to form a two-chip platform. The processor includes Integrated Display Engine, Processor Graphics and Integrated Memory Controller. 4.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 4.4.2 Signal I/O Description VGA_RED O VGA_GRN O VGA_BLU O VGA_HSYNC O Red for monitor, analog DAC output, designed to drive a 37.5Ω equivalent load. Green for monitor, analog DAC output, designed to drive a 37.5Ω equivalent load. Blue for monitor, analog DAC output, designed to drive a 37.5Ω equivalent load.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module Signal I/O Description DDI[1:2]_PAIR[0:3]+ O DDI 1 and 2 Pair[0:3] differential pairs DDI[1:2]_PAIR[0:3]Selects the function of DDI[1:2]_CTRLCLK_AUX+ and DDI[1:2]_CTRLDATA_AUX-. This pin shall have a 1M pull-down to logic ground on the Module. If this input is floating the AUX pair is used for the DP AUX+/- signals. If pulled-high the AUX pair contains the CTRLCLK and CTRLDATA signals.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module DDI2_PAIR3+ D49 DP2_LANE3+ TMDS2_CLK+ DDI2_PAIR3- D50 DP2_LANE3- TMDS2_CLK- DDI2_CTRLCLK_AUX+ C32 DP2_AUX+ HDMI2_SCL DDI2_CTRLDATA_AUX- C33 DP2_AUX- HDMI2_SDA DDI2_DDC_AUX_SEL C34 CONFIG1 (pull down to GND) Pull up to 5V DDI2_HPD (3.3V active high signal) D44 4.4.3.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 4.4.3.4 Embedded DisplayPort (eDP) Embedded DisplayPort (eDP) is an embedded version of the DisplayPort standard oriented towards applications such as notebook and All-In-One PCs. eDP is supported only on Digital Display Port 1. The resolution is up to 1920x1080 at D2550 CPU and 1366x768 at N2600 CPU.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 4.6.1 Signal I/O Description USB_6_7_OC# I USB over-current sense, USB 6 and 7. A pull-up for this line shall be present on the Module. An open drain driver from a USB current monitor on the Carrier Board may drive this line low. Do not pull this line high on the Carrier Board. USB 3.0 There are four USB 3.0 ports by extended from the Port 3 of the PCIe x1 interface.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 4.8 PCI Express 4.8.1 PCI Express x1 There are four one-lane PCI Express ports available in the PCH NM10. The ports are compliant to the PCI Express 1.0 specification running at 2.5 Gb/s. Only two PCIe x1 Ports, 0~1, are left on the CT-CCV6X COM™ Express connector since Port 2 is occupied by GbE and Port 3 is occupied by USB3.0.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 4.10 Ethernet The Intel® 82583V, a fully-integrated Gigabit Ethernet Media Access Control (MAC) provides 10/100/1000Mb/s Ethernet interface. The Intel® 82583V is connected to Port 2 of the PCIe x1 in the PCH. Gigabit transformer has to be designed on the Carrier Board. The integrated GbE controller contains power management registers for PCIE, so it supports the Advanced Configuration and Power Interface (ACPI) specification.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module Signal I/O Description LPC_SERIRQ I/O LPC serial interrupt LPC_CLK O LPC clock output – 33MHz nominal 4.12 SPI The Serial Peripheral Interface (SPI) is a 4-pin interface that supports SPI-compatible flash devices. The SPI flash device can be up to 16MB (128Mb). The SPI bus is clocked at either 20MHz, 25MHz, 33MHz or 50 MHz. SPI devices selected should support one of these frequencies.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module Carrier Board of standards such as Smart Battery. The maximum capacitance on the Carrier Board shall not exceed 100pF. Signal I/O Description SMB_CK I/OD System Management Bus bidirectional clock line SMB_DAT I/OD System Management Bus bidirectional data line SMB_ALERT# I System Management Bus Alert – active low input can be used to generate an SMI# (System Management Interrupt) or to wake the system. 4.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module Pin # GPIO# Default Configuration A93 GPIO4 GPO0 A85 GPIO3 GPI3 A67 GPIO2 GPI2 A63 GPIO1 GPI1 A54 GPIO0 GPI0 The GPIO function, provided by Intel Tiger Point NM10, can be accessed through GPIO Base Address Register (GPIOBASE). The configuration on CT-CCV6X is described as below. Register Address GPIOBASE Base Address 0x500 The general I/O read/write function is used to access and configure the NM10.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module GPIO Input/Output Select Register 2 (Offset GPIOBASE+0x34) Bit 7 Bit 6 GPIO7 GPIO6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 GPIO5 GPIO4 Bit 0 Bit X = 0 means Output Pin Bit X = 1 means Input Pin 4.16.2.3 GPIO Level for Input or Output Register 1 (Offset GPIOBASE+0x0C) If Pin X is configured as output, the output value (0 or 1) could be selected by user. If it is programmed as an input, this register reflects the state of the input signal.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 4.16.2.5 PSUEDO CODE Example 1 Change GPIO2 from output to input Step1: ByteData = ReadIOByte(0x504) Step2: ByteData = ByteData | Bit 4 Step3: WriteIOByte(0x504, ByteData) //Read current setting from configuration register //Set Bit4 1.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 4.18 Thermal Management Signals Signal I/O Description THRMTRIP# O THRM# I Active low output indicating that the CPU has entered thermal shutdown. Input from off-module temp sensor indicating and over-temp situation. 4.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 4.20 Watchdog Timer Enable TCO Timer Reboot Function Set Initial Value into Timer Register Reload Timer Value into Register Start to Count 4.20.1 Board Design The WDT (Watchdog Timer) is implemented by using TCO function in NM10. Register Address TCO I/O Base (TCOBASE) 0x460 RCBA Memory Base (RCBA) 0xFED1C000 Notes: 1. 2. TCO (Total Cost of Ownership) RCBA (Root Complex Base Address) 4.20.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module The system will be rebooted after user’s setting +2 seconds. 2 seconds added is Intel’s limitation. Step2 Set Initial Value into Timer Register Target: Set TCO Timer Initial Value (Offset 0x12) Step1: WordData = ReadIOWord(0x472) //0x460+0x12 Step2: WordData = Set Bit[9:0] //0x000~0xFFF. 1 ticks = 0.6s Step3: WriteIOWord(0x472,WordData) //Write back to IO Example: If you want to reboot after 5 seconds, you should set WordData to 0x05.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module V. SYSTEM BIOS The system BIOS software is stored on EEPROM. The BIOS provides an interface to modify the configuration. When the battery is removed, all the parameters will be reset. Turn on the computer and press or to enter the setup screens. 5.1 Main The Main setup screen is showed as following when the setup utility is entered. System Date/Time is set up in the Main Menu.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.2 Advanced Launch PXE OpROM : Enable or Disable Boot Option for Legacy Network Devices.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.2.1 ACPI Settings Enable ACPI Auto Configuration: Enable or Disable BIOS ACPI Auto Configuration. ACPI Sleep State: Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed. Select between [Suspend Disabled], [S1 (CPU Stop Clock)] and [S3 (Suspend to RAM)].
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.2.2 Trusted Computing Security Device Support enables or disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.2.3 CPU Configuration Hyper-threading: Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and disabled for other OS (OS not optimized for Hyper-Threading Technology). When disabled, only one thread per enabled core is enabled. Execute Disable Bit: XP can prevent certain classes of malicious buffer overflow attacks when combined with a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SusE Linux 9.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.2.4 IDE Configuration The BIOS automatically detects the presence of SATA device and the hardware installed in the SATA ports will be showed in the configuration. Each port can be enabled or disabled individually. Configure SATA as: Select IDE or AHCI mode for SATA controller operations. Port0 Speed Limit: Select between [No Limit], [GEN1 Rate], or [GEN2 Rate].
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.2.5 USB Configuration Legacy USB Support: AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications. EHCI Hand-off: This is a workaround for OS without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver. USB transfer time-out: Select between [1 sec], [5 sec], [10 sec] or [20 sec].
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.2.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.2.7 W83627DHG Super IO Configuration Two serial ports could be configured.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.2.7.1 Serial Port0 Configuration Each serial port could be enabled or disabled.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.2.7.2 Serial Port1 Configuration Each serial port could be enabled or disabled.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.2.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.2.9 PPM Configuration CPU C state Report When this option is set to “enabled” (default is set to disabled), it will expand two sub-options: “Enhanced C state” and “CPU C6 state”.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.3.1 Host Bridge Select Memory Power Voltage Support: Select between [1.5V] and [1.35V].
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.3.1.1 Intel IGD Configuration IGFX – Boot Type: Select the Video Device which will be activated during POST. This has no effect if external graphics present. Select between [VBIOS Default], [CRT], [LFP], [EFP], [CRT+EFP] and [LFP+EFP].
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.3.2 South Bridge TPT Devices: Enable or disable Intel(R) IO Controller Hub (TPT) devices. DMI Link ASPM Control: The control of Active State Power Management on both NB side and SB side of the DMI Link. PCI-Exp. High Priority Port: Select a PCI Express High Priority Port between [Disabled], [Port 0], [Port 1], [Port 2] and [Port 3].
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.3.2.1 TPT Devices Azalia Controller: Select between [Disabled] and [HD Audio] USB Function: Disable or enable USB Function. USB 2.0(EHCI) Support: Enable or disable USB2.0 (EHCI) Support.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.3.2.2 PCI Express Root Port Configuration Each PCI Express Port from 0 to 3 can be setup. Each PCI Express Root Port can be enabled or disabled individually.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.4 Boot Boot Configuration: Number of seconds to wait for setup activation key. 65535 (0xFFFF) means indefinite waiting. Bootup NumLock State: Select [Enable] or [Disable] for the keyboard NumLock state. Quiet Boot: Enables or disables Quiet Boot option. GateA20 Active: [Upon Request] – GA20 can be disabled using BIOS services. [Always] – do not allow disabling GA20; this option is useful wen any RT code is executed above 1MB.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.4.1 CSM parameters OpROM execution, boot options filter, etc. Launch CSM: This option controls if CSM will be launched always or never. Boot option filer: This option controls what devices system can boot to [UEFI and Legacy], [Legacy only] or [UEFI only]. Launch PXE OpROM policy: This controls the execution of UEFI and Legacy PXE OpROM, [Do not launch], [UEFI only] or [Legacy only].
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.5 Security Administrator’s and User’s passwords could be set. If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup, the user will have administrator rights. The minimum length of the password is 3 and the maximum length is 20.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 5.6 Save and Exit Save Changes and Exit: Exit system setup after saving the changes. Discard Changes and Exit: Exit system setup without saving any changes. Save Changes and Reset: Reset the system after saving the changes. Discard Changes and Reset: Reset system setup without saving any changes. Save Changes: Save Changes done so far to any of the setup options. Discard Changes: Discard Changes done so far to any of the setup options.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module VI. Address Map 6.1 I/O Port Address Map The assignment of the I/O port addresses for the CT-CCV6X with CT-BT601 carrier board under Windows® 7 Ultimate/64bit are shown below.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module ６１
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 6.2 Interrupt Controller (IRQ) Map The interrupt controller map for the CT-CCV6X with the CT-BT601 carrier board under Windows® 7 Ultimate/64bit are as shown below.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module ６３
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module ６４
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module 6.3 Memory Map The memory map of DRAM for the CT-CCV6X with CT-BT601 carrier board under Windows® 7 Ultimate/64bit are shown below.
CT-CCV6X Intel Atom D2000/N2000 COM Express Type 6 Module VII. Electrical Specification 7.1 Input Power The carrier board for the CT-CCV6X shall supply a single main power rail with a nominal value of +12V and two additional rails, a +5V standby power and +3V RTC power.
