User Guide EVGA Z97 Stinger Specs & Initial Installation (Part 1) -1-
Table of Contents Before you Begin………………………………………………………………………………..3 Parts Not in the kit……………………………………………………………………………...4 Intentions of the kit……………………………………………………………………………..4 Motherboard Specifications ...................................................................................................................... 5-6 Unpacking and Parts Descriptions ............................................................................................................... 7 Equipment ............................
Before You Begin… Welcome to a new class of high performance motherboards that boast 4th and 5th Generation Intel® Core™ Processor compatibility. The Z97 platform takes you to a new level of performance and efficiency. We have refined the GUI BIOS interface, reimagined power VRM that focuses on efficiency, added MPCIE support and loaded with features like Creative Sound Core3D quad-core audio processor, Intel Gigabit LAN, native SATA 6G/USB 3.0 and more.
Parts NOT in the Kit This kit contains all the hardware necessary to install and connect your new EVGA Z97 Stinger Motherboard.
EVGA Z97 Motherboard Motherboard Specifications Size: mITX form factor of 6.7 inches x 6.7 inches Microprocessor support: Intel Socket 1150 Processor Operating Systems: Supports Windows 8 / 7 Contains Intel Z97 chipset System Memory support: Supports Dual channel DDR3 up to 2666MHz+. Officially supports up to 16GB of DDR3 memory. USB 2.0 Ports: 6x from Intel Z97 PCH – 4x external Supports hot plug Supports wake-up from S1 and S3 mode Supports USB 2.0 protocol up to a 480 Mbps transmission rate USB 3.
Onboard LAN: 1x Intel i217 Gigabit Ethernet PHY Supports 10/100/1000 Mb/sec Ethernet Onboard Audio: Creative Core3D Quad-Core Audio Processor (CA0132) Supports 6-channel (5.1) audio Supports Optical Output PCI-E 3.
Unpacking and Parts Descriptions Equipment The following accessories are included with the EVGA Z97 Stinger Motherboard: The EVGA Z97 Stinger Motherboard This PCI-E motherboard contains the Intel Z97 chipset. I/O Shield Installs in the system case to block radio frequency transmissions, protect internal components from dust, foreign objects, and aids in proper airflow within the chassis. 2x SATA 3G/6G Data Cables Used to support the SATA protocol and each one connects a single drive to the motherboard.
Intel Z97 Stinger Motherboard The EVGA Z97 Stinger Motherboard with the Intel Z97 and PCH Chipset. Figure 1 shows the motherboard and Figure 2 shows the back panel connectors FIGURE 1.
1. CPU Socket 1150 7. Intel SATA 6G/3G Ports 13. Reset Button 2. Intel Z97 Southbridge 8. Front Panel Connectors 14. PCI-E Slot 16x/8x 3. CPU Fan Header (1 amp PWM) 9. Debug LED / CPU Temp Monitor 15. Mini PCI-E/mSATA 4. DDR3 Memory DIMM Slots 1-2 10. USB 3.0 Headers 16. Back Panel Connectors (Figure 2) 5. 24-pin ATX power connector 11. CMOS Battery 17. 8 pin EPS Connector 6. Fan Headers (1 amp DC) 12. Power Button 18.
Figure 2. Chassis Rear Panel Connectors 1. USB 2.0 4. eSata 7. HDMI 2. USB 3.0 5. NIC Port 8. Optical Out 3. BIOS/CMOS Reset 6. Display Port 9. Analog Audio Output Jacks Analog Audio Port Breakdown 2/2.1 (Channel) 4.0/4.1 (Channel) 5.
Preparing the Motherboard Installing the CPU Be very careful when handling the CPU. Hold the processor only by the edges and do not touch the bottom of the processor. Note: Use extreme caution when working with the CPU, not to damage any pins in the CPU socket on the motherboard! Use the following procedure to install the CPU onto the motherboard: Remove the plastic protective socket cover by pulling it straight up. Be sure not to damage any of the pins inside the socket.
Align the notches on the CPU to the notches in the socket. Lower the processor straight down into the socket. Note: Make sure the CPU is fully seated and level in the socket. Lower the load plate so it is resting on the CPU. Carefully lock the lever back into place. Installing the CPU Cooling Device There are many different cooling devices that can be used with this motherboard. Follow the instructions that come with your cooling assembly.
Installing System Memory (DIMMs) Your Z97 Stinger has (2) 240-pin slots for DDR3 memory. These slots support 2GB, 4GB and 8GB DDR3 DIMMs. There must be at least one memory slot populated to ensure normal operation. The Intel Z97 chipset supports dual channel memory; supports a maximum of 16GB of DDR3 and up to 2666MHz+ in dual channel configuration. It is required to populate slot 1 first. Board will not boot if slot 1 is not populated. Use the following procedure to install DIMMs.
Compliance Information FCC Compliance Information This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
