User Guide EVGA Z97 FTW Specs and Initial Installation (Part 1) -1-
Table of Contents Before you Begin……………………………………………………………………..…………3 Parts Not in the kit………………………………………………………………………….…..4 Intentions of the kit…………………………………………………………………..…………4 Motherboard Specifications ...................................................................................................................... 5-6 Unpacking and Parts Descriptions ............................................................................................................... 7 Equipment ............................
Before You Begin… Welcome to a new class of high performance motherboards that boast 4th and 5th Generation Intel® Core™ Processor compatibility. The Z97 platform takes you to a new level of performance and efficiency. We have refined the GUI BIOS interface, reimagined power VRM that focuses on efficiency, added M.2 support and loaded with features like 2-Way-SLI, Intel Gigabit LAN, native SATA 6G/USB 3.0 and more. All sitting on a 6 layer PCB to improve performance and efficiency.
Parts NOT in the Kit This kit contains all the hardware necessary to install and connect your new EVGA Z97 FTW Motherboard.
EVGA Z97 Motherboard Motherboard Specifications Size: ATX form factor of 12 inches x 9.6 inches Microprocessor support: Intel Socket 1150 Processor Operating Systems: Supports Windows 8 / 7 Contains Intel Z97 chipset System Memory support: Supports Dual channel DDR3 up to 2666MHz+. Officially supports up to 32GB of DDR3 memory. USB 2.0 Ports: 6x from Intel Z97 PCH – 4x external, 2x internal Supports hot plug Supports wake-up from S1 and S3 mode Supports USB 2.
- Supports hot plug 2x SATA3/6G Marvell 88E9182 Onboard LAN: 1x Intel i217 Gigabit PHY Supports 10/100/1000 Mb/sec Ethernet Onboard Audio: Realtek Audio (ALC898) Supports 8-channel (7.1) audio Supports Jack-Sensing function Supports Optical Output PCI-E 3.
Unpacking and Parts Descriptions Equipment The following accessories are included with the EVGA Z97 FTW Motherboard: The EVGA Z97 FTW Motherboard This PCI-E motherboard contains the Intel Z97 chipset. I/O Shield Installs in the system case to block radio frequency transmissions, protect internal components from dust, foreign objects, and aids in proper airflow within the chassis. 4 x SATA 3G/6G Data Cables Used to support the SATA protocol and each one connects a single drive to the motherboard.
Intel Z97 FTW Motherboard The EVGA Z97 FTW Motherboard with the Intel Z97 and PCH Chipset. Figure 1 shows the motherboard and Figure 2 shows the back panel connectors FIGURE 1.
1. CPU Socket 1150 13. USB 2.0 Headers 25. M.2 Slot 2. Intel Z97 Southbridge 14. USB 3.0 Headers 26. Front Panel Audio Connector 3. CPU Fan Headers (1 amp PWM) 15. CMOS Battery 27. EVGauge 4. DDR3 Memory DIMM Slots 1-4 16. CMOS Reset Button 28. Back Panel Connectors (Figure 2) 5. 24-pin ATX power connector 17. Power Button 29. 8 pin EPS Connector 6. Fan Headers (1 amp DC) 18. Reset Button 30. Supplemental PCI-E 6pin Power 7. PCI-E Disable Dipswitches 19. PC Speaker 31.
Figure 2. Chassis Rear Panel Connectors 1. USB 2.0 4. NIC Port (Intel i217) 7. Optical Out 2. USB 3.0 5. Display Port 8. Analog Audio Output Jacks 3. BIOS/CMOS Reset 6. HDMI Analog Audio Port Breakdown 2/2.1 (Channel) (4.0/4.1 Channel) 5.1 (6 Channel) 7.
Preparing the Motherboard Installing the CPU Be very careful when handling the CPU. Hold the processor only by the edges and do not touch the bottom of the processor. Note: Use extreme caution when working with the CPU, not to damage any pins in the CPU socket on the motherboard! Use the following procedure to install the CPU onto the motherboard: Remove the plastic protective socket cover by pulling it straight up. Be sure not to damage any of the pins inside the socket.
Align the notches on the CPU to the notches in the socket. Lower the processor straight down into the socket. Note: Make sure the CPU is fully seated and level in the socket. Lower the load plate so it is resting on the CPU. Carefully lock the lever back into place. Installing the CPU Cooling Device There are many different cooling devices that can be used with this motherboard. Follow the instructions that come with your cooling assembly.
Installing System Memory (DIMMs) Your Z97 FTW has (4) 240-pin slots for DDR3 memory. These slots support 2GB, 4GB and 8GB DDR3 DIMMs. There must be at least one memory slot populated to ensure normal operation. The Intel Z97 chipset supports dual channel memory; supports a maximum of 32GB of DDR3 and up to 2666MHz+ in dual channel configuration. It is required to populate slot 1 first. The board will not boot if slot 1 is not populated. Use the following procedure to install DIMMs.
Compliance Information FCC Compliance Information This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
