User Guide EVGA X99 Classified Specs and Initial Installation (Part 1) -1-
Table of Contents Before you Begin………………………………………………………………………3 Parts Not in the kit…………………………………………………………………….4 Intentions of the kit……………………………………………………………………4 Motherboard Specifications……………………………………………………………5 Unpacking and Parts Descriptions……………………………………………………..7 Equipment……………………………………………………………………………..7 Hardware Installation…………………………………………………………………..8 Component legend………..……………………………………………………………8 PCI-E Slot Breakdown………………………………………………………………....9 Rear I/O Panel legend………………………………………………………………..
Before You Begin… EVGA welcomes you to the next generation of ground breaking performance, the X99 Classified. The X99 platform redefines high performance with the introduction of the first ever quad channel DDR4 architecture fueled by Intel’s Haswell-E/Broadwell-E CPU family for up to 128GB’s of RAM running at a maximum memory speed up to 3000MHz+ (OC), possible due to the 4 layer memory T-Routing design.
Parts NOT in the Kit This kit contains all the hardware necessary to install and connect your new EVGA X99 Classified Motherboard.
Motherboard Motherboard Specifications Size: EATX form factor of 12 inches x 10.375 inches (305x264mm) Microprocessor support: Intel Socket 2011-3 Processor Operating Systems: Supports Windows 8 / 7 Contains Intel X99 chipset System Memory support: Supports Quad channel DDR4 up to 3000MHz+ (OC). Supports up to 128GB of DDR4 memory. USB 2.0 Ports: 8x from Intel X99 PCH – 6x external, 2x internal Supports hot plug Supports wake-up from S1 and S3 mode Supports USB 2.
Ethernet Teaming Supported Onboard Audio: Creative Core3D Quad-Core Audio Processor (CA0132) Supports 6-channel (5.1) audio Supports Optical Output PCI-E 3.0 Support: Low power consumption and power management features Power Functions: Supports ACPI (Advanced Configuration and Power Interface) Supports S0 (normal), S1 (power on suspend), S3 (suspend to RAM), S4 (Suspend to disk - depends on OS), and S5 (soft - off) Expansion Slots: 5x PCI-E 16x slot 2x16/8, 3x8, 4x8 1x PCI-E 4x slot 2x M.
Unpacking and Parts Descriptions Equipment The following accessories are included with the EVGA X99 Classified Motherboard: The EVGA X99 Classified Motherboard This PCI-E motherboard contains the Intel X99 chipset. I/O Shield Installs in the system case to protect internal components from dust, foreign objects, and aids in proper airflow within the chassis. 6x SATA 6G Data Cables Used to support the SATA protocol and each one connects a single drive to the motherboard.
Intel X99 Classified Motherboard The EVGA X99 Classified Motherboard with the Intel X99 and PCH Chipset. Figure 1 shows the motherboard and Figure 2 shows the back panel connectors FIGURE 1.
1. CPU Socket 2011-3 13. USB 3.0 Headers 25. EVGauge 2. Intel X99 Southbridge 14. USB 2.0 Headers 26. Thunderbolt GPIO Connector 3. CPU Fan Header (1 amp PWM) 15. CMOS Reset Button 27. MCU Firmware update connector 4. DDR4 Memory DIMM Slots 1-8 16. Power Button 28. Back Panel Connectors (Figure 2) 5. 24-pin ATX power connector 17. Reset Button 29. 8 pin EPS Connector 6. Fan Headers (1 amp DC) 18. PC Speaker 30. Supplemental PCI-E 6pin Power 7. PCI-E Disable Dipswitches 19.
Figure 2. Chassis Rear Panel Connectors 1. USB 2.0 4. Intel i217 NIC 2. USB 3.0 5. Intel i210 NIC 3. BIOS/CMOS Reset 6. Optical Out 7. Analog Audio Output Jacks Analog Audio Port Breakdown 2/2.1 (Channel) 4.0/4.1 (Channel) 5.
Preparing the Motherboard Installing the CPU Be very careful when handling the CPU. Hold the processor only by the edges and do not touch the bottom of the processor. Note: Use extreme caution when working with the CPU, not to damage any pins in the CPU socket on the motherboard! Use the following procedure to install the CPU onto the motherboard: Unhook the left socket lever by pushing down and towards the socket. Unhook the right socket lever by pushing down and towards the socket.
Align the notches on the CPU to the notches in the socket. Lower the processor straight down into the socket. Note: Make sure the CPU is fully seated and level in the socket. Lower the load plate so it is resting on the CPU. Press the right socket lever down to lock into place. Carefully lock the left lever back into place. Installing the CPU Cooling Device There are many different cooling devices that can be used with this motherboard.
Installing System Memory (DIMMs) Your X99 Classified has (8) 288-pin slots for DDR4 memory. These slots support 2GB, 4GB, 8GB and 16GB DDR4 DIMMs. There must be at least one memory slot populated to ensure normal operation. The Intel X99 chipset supports quad channel memory; supports a maximum of 128GB of DDR4 and up to 3000MHz+ (OC) in quad channel configuration. It is required to populate an odd slot (1, 3, 5, 7) first. The board will not boot if only even slots (2, 4, 6, 8) are populated.
Compliance Information FCC Compliance Information This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
