Contents = Installation Condition 1 = Two-Function Rain Shower System (MOI BOBBY 2 = Three-Function Rain Shower System (MOE BBL) 8 = Clean and Maintenance coon 15 .
= Installation Condition 1. Check the Accessories List to verify that all parts are complete in this package. 2. Do not disassemble the main body by yourself. 3. Connect inlet pipes to supply valves. 4. Make sure inlet pipes and supply valves have been installed and cleaned, with no impurities in the pipeline. 5. After installation, check all joints for leakages. 6. Do not leave the rain shower system exposed to a severely corrosive environment.
= Two-Function Rain Shower System = Accessories List Part name Qty No. Part name Qty Shower head 11 Water diverted screw Handle cap 10 Water diverted cap Shower arm 1 12 Water diverted 1 3 Shower arm cover 1 13 Panel 1 4 Hand shower 1 14 Main body 1 § Hand shower holder 1 145 Body box fittings 4 § Shower hose 1 16 Wrench 1 7 Handle 1 17 Water-saving film 1 8 Handle screw 1 18 Gloves WARNING: Choking hazard. Please keep all small parts and plastic bags out of the reach of children.
Installation Depth of Main Body 2 14/18" {ES imminent i The wall _— Hf thenceforward bon sup forth ceramic Be surface, hen if whi be vat tush te embedded Guo healthy th ceramic repudiates. 1 boil size | 1 Authoritarian | ACETATE WET wt BFE Edm AGE Lien Notice: The installation depth of main body should be no less than 2 11/16" (68mm) and no more than 3 7/16" (88mm), including the thickness of tile. Otherwise, the panel cannot be installed.
= Main body Valve Installation 1. Make marks according to the size of the main body valve, and then drill anchors into the wall. A Please note that the level meter should be parallel with the wall, otherwise the panel cannot be installed. 2. Please fix the main body to the wall, remove the plastic protective cover and install panel, water diverted, screw and water diverted cap step by step. 3. Install the handle with the screw and handle cap.
= Piping Instructions Before Tiling N , Embarrassing Comte top ok pp FINESPUN T152% Recommend using Copper drop oar pipe nanobot 412} USA /TENPIN 2 Canada: 1/214 NAT Cold water riot pie Lo inlets 1. Connect the water pipes as illustrations. Please make sure the mark 1 is facing upward. 2. Before tiling, turn on the water and pull the shower handle to check for leakages. Nn ‘Housewarming install hot water and cold water inlet strictly as { instructions.
= Shower Head and Shower Arm installation Mainframe TVA Alton 1. Connect shower arm with the cover before screwing arm into riser connection to prevent damage. 2. Fix shower head onto shower arm, and apply tape to pipe threads on both ends. 3. Do not over tighten shower head. It is 360° swivel connection. = Hand Shower Holder Installation Step 1. Screw the thread into the water pipe inside the wall. Step 2. Screw the hand shower holder with cover into the thread. Step 3.
= Three-Function Rain Shower System Model 6603 # Accessories List _8No Part name Qty No, Part name Qly i Shower head 7 13 Water diverted 1 2 “Shower arm 1 i4 Panel 1 3 Shower arm cover 1 15 Main body 1 4 Hand shower 1 18 Bathtub spout body 1 5 Alder parts 1 17 Bathtub spout pane 7 6 Hand shower holder 1 11" Body box filings Wrench 1 8 Handle 1 2% Water-saving film 1 9 Handle screw 1 2% Gloves 2 10 Handle cap 2 11 Water diverted cap 7 12 Water diverted screw 1 431 Choking hazard, Pleads esp al small pairs an
= Installation Dimensions of Embedded Pipes Chumming Pleas refer to shove for height dimensions of shower Installation. STILTS TTT = Installation Depth For Shower Arm & Shower Holder Fas of plasterboard should bu flush with finish wai: ding Please refer to above for height 184 dimensions of shower Installation.
Installation Depth of Main Body *{Bernini Like wall if ibe embedded box is exposed Ter the colonnade the surface, then it i Bee cat Bath Hee edibleness of bow with the carmine tle surface. i nde size : Hab sender inset TATE IWS 3 THE me bs HOE Pam Notice: The installation depth of main body should be no less than 2 11/16" (68mm) and no more than 3 7/16" (88mm), including the thickness of tile. Otherwise, the panel cannot be installed.
= Main body Valve Installation 30 in Dep ge sas 57116" 1. Make marks according to the size of the main body valve, and then drill anchors into the wall. A Please note that the level meter should be parallel with the wall, otherwise the panel cannot be installed. 2. Please fix the main body to the wall, remove the plastic protective cover and install panel, water diverted, screw and water diverted cap step by step. 3. Install the handle with the screw and handle cap.
= Piping Instructions Before Tiling Preoperative pps car sin SOWN TUR Hed water sutler pips Cold water inlet pipe Hol water ind at pipe Ll sled 1. Connect the water pipes as illustrations. Please make sure the mark 1 is facing upward. 2. Before tiling, turn on the water and pull the shower handle to check for leakages. ON Warning:must install hot water and cold water inlet strictly as _ instructions.
Step 1. Put the bathtub spout panel on the top of the bathtub spout body. Step 2. Screw the bathtub spout body into the thread. = Shower Head and Shower Arm installation Female thread rainbow 1. Connect shower arm with the cover before screwing arm into riser connection to prevent damage. 2. Fix shower head onto shower arm, and apply tape to pipe threads on both ends. 3. Do not over tighten shower head. It is 360° swivel connection.
= Hand Shower Holder Installation Step 3 tep 2 Step Tums Step 1. Screw the thread into the water pipe inside the wall. Step 2. Screw the hand shower holder with cover into the thread. Step 3. Rotate and fix the holder with the wrench. Step 4. Connect hand shower and the hose.
= Clean and Maintenance Do's 1. In order to keep the mixer surface bright, please clean the mixer regularly. 2. Rinse faucet with clean water and wipe it with soft cotton cloth. 3. Use one of the following cleaners to remove dirt on the surface: a. Mild liquid cleaner. b. Colorless glass cleaner and powder cleaner which does not cause abrasion and can be dissolved completely. c. Polish liquid which does not cause abrasion. Don'ts a.
= Warranty Warranty Duration All parts of this faucet system are warranted to the original purchaser to be free from defects in material and workmanship for 5 years from the date of purchase as shown on the invoice. Repair and Replacement Within the warranty period, if the product has defects in material and workmanship, Ever stein will repair or replace the product free of charge. Ever stein may require you provide the invoice when repairing or replacing the product.
