Datasheet

ManualsBrandsEverlight Electronics ManualsIR LEDsIR-LED 940nm SMD

Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 1 of 10

Device No：DTR-017-041 Prepared date：07-20-2005 Prepared by：Jaine Tsai

Technical Data Sheet

0805 Package Infrared Chip LED

IR17-21C/TR8

Features

․Small double-end package

․Low forward voltage

․Good spectral matching to Si photo detector

․Package in 8mm tape on 7” diameter reel

․Pb free

․The product itself will remain within RoHS compliant version.

Descriptions

․IR17-21C is an infrared emitting diode in

miniature SMD package which is molded in a

water clear plastic with flat top view lens.

․The device is spectrally matched with silicon

photodiode and phototransistor.

Applications

․PCB mounted infrared sensor

․Infrared emitting for miniature light barrier

․Floppy disk drive

․Optoelectronic switch

․Smoke detector

Device Selection Guide

Chip

LED Part No.

Material

Lens Color

IR GaAlAs Water Clear

Summary of content (10 pages)

PAGE 1
Technical Data Sheet 0805 Package Infrared Chip LED IR17-21C/TR8 Features ․Small double-end package ․Low forward voltage ․Good spectral matching to Si photo detector ․Package in 8mm tape on 7” diameter reel ․Pb free ․The product itself will remain within RoHS compliant version. Descriptions ․IR17-21C is an infrared emitting diode in miniature SMD package which is molded in a water clear plastic with flat top view lens. ․The device is spectrally matched with silicon photodiode and phototransistor.
PAGE 2
IR17-21C/TR8 Package Dimensions Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Continuous Forward Current IF 65 Units mA Peak Forward Current IFP 1.
PAGE 3
IR17-21C/TR8 Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Ee Radiant Intensity Condition IF=20mA Min. Typ. Max. 0.2 0.8 -- IF=100mA -- 4.0 --- nm -- nm Pulse Width≦100μs ,Duty≦1% Peak Wavelength λp IF=20mA -- Spectral Bandwidth Δλ IF=20mA -- 940 45 IF=20mA -- 1.2 1.5 IF=100mA -- 1.4 1.8 VR=5V --- 2.6 -- 4.
PAGE 4
IR17-21C/TR8 Typical Electro-Optical Characteristics Curves Fig.1 Forward Current vs. Ambient Temperature Fig.2 Spectral Distribution 140 100 IF=20mA Ta=25° C 120 80 100 80 60 60 40 40 20 20 0 -25 0 20 40 60 80 100 Fig.3 Peak Emission Wavelength Ambient Temperature 0 Fig.4 Forward Current vs. Forward Voltage 4 10 980 960 3 10 940 2 10 920 900 -25 0 25 50 75 100 1 10 0 1 2 3 Everlight Electronics Co., Ltd. http:\\www.everlight.
PAGE 5
IR17-21C/TR8 Typical Electro-Optical Characteristics Curves Fig.5 Relative Intensity vs. Fig.6 Relative Radiant Intensity vs. Forward Current Angular Displacement -20 Ie-Radiant Intensity(mW/sr) 100 -10 0 10 20 30 10 1 0 0 10 10 2 1 10 10 3 1.0 40 0.9 50 0.8 0.7 60 10 4 70 80 0.6 0.4 0.2 0 0.2 0.4 0.6 IF-Forward Current (mA) Fig.8 Forward Voltage vs. Fig.7 Relative Intensity vs. Ambient Temperature(°C) Ambient Temperature(°C) 1.3 1.0 0.8 1.2 IF=20mA 0.6 1.1 0.
PAGE 6
IR17-21C/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.
PAGE 7
IR17-21C/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered.
PAGE 8
IR17-21C/TR8 Reliability Test Item And Condition The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% NO. Item Test Conditions Test Hours/ Sample Cycles Sizes 1 REFLOW Soldering TEMP.：260℃±5℃ 6Mins 5secs 15mins 50Cycles 2 Temperature Cycle H : +100℃ 5mins L : -40℃ 15mins 3 Thermal Shock H :+100℃ 4 High Temperature Storage TEMP.：+100℃ 5 Low Temperature Storage TEMP.：-40℃ 6 DC Operating Life IF=20mA 7 High Temperature/ 85℃ / 85% R.
PAGE 9
IR17-21C/TR8 Package Dimensions Taping Dimensions Unit:mm Everlight Electronics Co., Ltd. http:\\www.everlight.
PAGE 10
IR17-21C/TR8 Packing Quantity Specification 1.3000Pcs/1Volume，1Volume/1Bag 2.10Boxes/1Carton Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place RoHS IR17-21C/TR8 Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2.