Datasheet

ManualsBrandsEverlight Electronics ManualsLEDsSMD LED 650nm 0603 72mcd 20mA

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 1 of 10

Device No:DSE-0002398 Prepared date:17-Sep-2009 Prepared by:Wuhongmei

Technical Data Sheet

0603 Package Chip LED(0.6mm Height)

19-213/R8C-FN1P2/3T

Features

․Package in 8mm tape on 7〞diameter reel.

․Compatible with automatic placement equipment.

․Compatible with infrared and vapor phase reflow

solder process.

․Mono-color type.

․Pb-free.

․The product itself will remain within RoHS complaint Version.

Descriptions

․The 19-213 SMD LED is much smaller than lead frame

type components, thus enable smaller board size, higher

packing density, reduced storage space and finally

smaller equipment to be obtained.

․Besides, lightweight makes them ideal for miniature

applications. etc.

Applications

․Backlighting in dashboard and switch.

․Telecommunication: indicator and backlighting in

telephone and fax.

․Flat backlight for LCD, switch and symbol.

․General use.

Device Selection Guide

Chip

Part No.

Material

Emitted Color Resin Color

19-213/R8C-FN1P2/3T AlGaInP Deep Red Water Clear

Summary of content (10 pages)

PAGE 1
Technical Data Sheet 0603 Package Chip LED(0.6mm Height) 19-213/R8C-FN1P2/3T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within RoHS complaint Version.
PAGE 2
19-213/R8C-FN1P2/3T Package Outline Dimensions - + 1.0 Note: Tolerances Unless Dimension is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No:DSE-0002398 http://www.everlight.
PAGE 3
19-213/R8C-FN1P2/3T Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA IFP 60 mA Pd 60 mW ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Peak Forward Current (Duty 1/10 @1KHz) Power Dissipation Electrostatic Discharge(HBM) Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec.
PAGE 4
19-213/R8C-FN1P2/3T Bin Range Of Luminous Intensity Bin Min Max N1 28.5 36.0 N2 36.0 45.0 P1 45.0 57.0 P2 57.0 72.0 Unit Condition mcd IF=20mA Unit Condition nm IF=20mA Bin Range Of Dom. Wavelength Groups F Bin Min Max FF4 636.0 641.0 FF5 641.0 646.0 Notes: 1.Tolerance of Luminous Intensity ±11% 2.Tolerance of Dominant Wavelength ±1nm Everlight Electronics Co., Ltd. Device No:DSE-0002398 http://www.everlight.
PAGE 5
19-213/R8C-FN1P2/3T Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. Device No:DSE-0002398 http://www.everlight.
PAGE 6
19-213/R8C-FN1P2/3T Label explanation CAT: Luminous Intensity Rank Pb HUE: Dom. Wavelength Rank CPN : P N : XXXXXXXXXXXXX REF: Forward Voltage Rank XXXXXXXXXXXXX EVERLIGHT RoHS CAT : XXX HUE : XXX REF : XXX QTY : XXX LOT NO : XXXXXXXXXX Reference : XXXXXXXX MADE IN TAIWAN Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No:DSE-0002398 http://www.everlight.
PAGE 7
19-213/R8C-FN1P2/3T Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. Device No:DSE-0002398 http://www.everlight.
PAGE 8
19-213/R8C-FN1P2/3T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. Test Sample Ac/Re Hours/Cycles Size 22 Pcs. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 3 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 4 High Temperature Storage Temp. : 100℃ 1000 Hrs.
PAGE 9
19-213/R8C-FN1P2/3T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.
PAGE 10
19-213/R8C-FN1P2/3T 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered.