Datasheet

ManualsBrandsEverlight Electronics ManualsLEDsSMD LED 518nm 0603 360mcd 20mA

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 1 of 10

Device No:SZDSE-193-G18 Prepared date: 27-May-2005 Prepared by: Denghuadong

Technical Data Sheet

0603 Package Chip LED (0.6 mm Height)

19-213/GHC-XS1T1N/3T

Features

․Package in 8mm tape on 7〞diameter reel.

․Compatible with automatic placement equipment.

․Compatible with infrared and vapor phase reflow

solder process.

․Mono-color type.

․Pb-free.

․RoHS refer to SMD B type SGS report

Descriptions

․The 19-213 SMD Taping is much smaller than

lead frame type components, thus enable smaller

board size, higher packing density, reduced

storage space and finally smaller equipment to be

obtained.

․Besides, lightweight makes them ideal for

miniature applications. etc.

Applications

․Automotive: backlighting in dashboard and switch.

․Telecommunication: indicator and backlighting in

telephone and fax.

․Flat backlight for LCD, switch and symbol.

․General use.

Device Selection Guide

Chip

Part No.

Material Emitted Color

Lens Color

19-213/GHC-AS1T1N/3T InGaN Brilliant Green Water Clear

Summary of content (10 pages)

PAGE 1
EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 0603 Package Chip LED (0.6 mm Height) 19-213/GHC-XS1T1N/3T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free.
PAGE 2
EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-XS1T1N/3T Package Outline Dimensions - + Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev.
PAGE 3
EVERLIGHT ELECTRONICS CO.,LTD.
PAGE 4
EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-XS1T1N/3T Bin Range Of Dom. Wavelength Group X Bin Min Max W 515 520 X 520 525 Y 525 530 Unit Condition nm IF =20mA Bin Range Of Luminous Intensity Bin Min Max S1 180 225 S2 225 285 T1 285 360 Unit Condition mcd IF =20mA Bin Range Of Forward Voltage Group N Bin Min Max 10 2.70 2.90 11 2.90 3.10 12 3.10 3.30 13 3.30 3.50 14 3.50 3.70 Unit Condition V IF =20mA Notes: 1.Tolerance of Luminous Intensity ±10% 2.
PAGE 5
EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-XS1T1N/3T Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. http://www.everlight.com Rev.
PAGE 6
EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-XS1T1N/3T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank xxxxxx xxxxxx REF: Forward Voltage Rank RoHS xxxxxxxxxxxx xxxx xxxxxxxx Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev.
PAGE 7
EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-XS1T1N/3T Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Everlight Electronics Co., Ltd. http://www.everlight.com Rev.
PAGE 8
EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-XS1T1N/3T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs.
PAGE 9
EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-XS1T1N/3T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.
PAGE 10
EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-XS1T1N/3T 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. . EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.