Datasheet

ManualsBrandsEverlight Electronics ManualsLEDsSMD LED 591nm 0805 38mcd 20mA

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 1 of 9

Device No:SZDSE-171-019 Prepared date: 27-Oct-2007 Prepared by: Zhouhua

Technical Data Sheet

0805 Package Chip LED (1.0m Height)

17-21SURC/S530-XX/TR8

Features

ԦPackage in 8mm tape on 7ϛdiameter reel.

ԦCompatible with automatic placement equipment.

ԦCompatible with infrared and vapor phase reflow

solder process.

ԦMono-color type.

ԦPb-free.

ԦThe product itself will remain with in RoHS complaint version

Descriptions

ԦThe 17-21 SMD Taping is much smaller

than lead frame type components, thus

enable smaller board size, higher packing

density, reduced storage space and finally

smaller equipment to be obtained.

ԦBesides, lightweight makes them ideal for

miniature applications. etc.

Applications

ԦBacklighting in dashboard and switch.

ԦTelecommunication: indicator and backlighting in

telephone and fax.

ԦFlat backlight for LCD, switch and symbol.

ԦGeneral use.

Device Selection Guide

Chip

Part No.

Material

Emitted Color Resin Color

17-21SURC/S530-XX/TR8 AlGaInP Brilliant Red Water Clear

Summary of content (9 pages)

PAGE 1
EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 0805 Package Chip LED (1.0m Height) 17-21SURC/S530-XX/TR8 Features ԦPackage in 8mm tape on 7ϛdiameter reel. ԦCompatible with automatic placement equipment. ԦCompatible with infrared and vapor phase reflow solder process. ԦMono-color type. ԦPb-free.
PAGE 2
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SURC/S530-XX/TR8 Package Outline Dimensions - 1.05 + Note: The tolerances unless mentioned is ²0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No:SZDSE-171-019 Prepared date: 27-Oct-2007 Rev.
PAGE 3
EVERLIGHT ELECTRONICS CO.,LTD.
PAGE 4
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SURC/S530-XX/TR8 Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. http://www.everlight.com Device No:SZDSE-171-019 Prepared date: 27-Oct-2007 Rev.
PAGE 5
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SURC/S530-XX/TR8 Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank ̋̋̋̋̋̋ ̋̋̋̋̋̋ REF: Forward Voltage Rank RoHS ̋̋̋̋̋̋̋̋̋̋̋̋ ̋̋̋̋ ̋̋̋̋̋̋̋̋ Reel Dimensions Note: The tolerances unless mentioned is ²0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No:SZDSE-171-019 Prepared date: 27-Oct-2007 Rev.
PAGE 6
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SURC/S530-XX/TR8 Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel Note: The tolerances unless mentioned is ²0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. http://www.everlight.com Device No:SZDSE-171-019 Prepared date: 27-Oct-2007 Desiccant Rev.
PAGE 7
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SURC/S530-XX/TR8 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence levelΚ90% LTPDΚ10% Test Sample Hours/Cycles Size Ac/Re No. Items Test Condition 1 Reflow Soldering Temp. : 260к²5к Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100к 15min Н 5 min L : -40к 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100к 5min Н 10 sec L : -10к 5min 300 Cycles 22 PCS. 0/1 Temp.
PAGE 8
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SURC/S530-XX/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30к or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30кor less and 60% RH orless.
PAGE 9
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SURC/S530-XX/TR8 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350к for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered.