Datasheet

ManualsBrandsEverlight Electronics ManualsLEDsSMD LED 575nm 0805 17mcd 20mA

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 1 of 9

Device No:SZDSE-171- 110 Prepared date:12-09-2008 Prepared by:Cheng Dejiang

Technical Data Sheet

0805 Package Chip LED(1.0mm Height)

17-21SYGC/S530-E2/TR8

Features

․Package in 8mm tape on 7〞diameter reel.

․Compatible with automatic placement equipment.

․Compatible with infrared and vapor phase reflow

solder process.

․Mono-color type.

․Pb-free.

․The product itself will remain with in RoHS complaint version

Descriptions

․ The 17-21 SMD LED Taping is much

smaller than lead frame type components,

thus enable smaller board size, higher

packing density, reduced storage space

and finally smaller equipment to be

obtained.

․Besides, lightweight makes them ideal for

miniature applications. etc.

Applications

․ Backlighting in dashboard and switch.

․Telecommunication: indicator and backlighting in

telephone and fax.

․Flat backlight for LCD, switch and symbol.

․General use.

Device Selection Guide

Chip

Part No.

Material

Emitted Colour

Resin Colour

17-21SYGC/S530-E2/TR8 AlGaInP Brilliant Yellow Green Water Clear

Summary of content (9 pages)

PAGE 1
EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 0805 Package Chip LED(1.0mm Height) 17-21SYGC/S530-E2/TR8 Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free.
PAGE 2
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SYGC/S530-E2/TR8 Package Outline Dimensions - 1.05 + Note: Tolerances Unless Dimension ±0.1mm , Unit = mm Everlight Electronics Co., Ltd. Device No:SZDSE-171- 110 http://www.everlight.
PAGE 3
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SYGC/S530-E2/TR8 Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA IFP 60 mA Pd 60 mW ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40~ +90 ℃ Soldering Temperature Tsol Peak Forward Current (Duty 1/10 @1KHz) Power Dissipation Electrostatic Discharge(HBM) Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec.
PAGE 4
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SYGC/S530-E2/TR8 Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. Device No:SZDSE-171- 110 http://www.everlight.
PAGE 5
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SYGC/S530-E2/TR8 Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: Tolerances Unless Dimension ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No:SZDSE-171- 110 http://www.everlight.
PAGE 6
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SYGC/S530-E2/TR8 Carrier Tape Dimensions: Loaded quantity 10000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm , Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. Device No:SZDSE-171- 110 http://www.everlight.
PAGE 7
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SYGC/S530-E2/TR8 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs.
PAGE 8
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SYGC/S530-E2/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.
PAGE 9
EVERLIGHT ELECTRONICS CO.,LTD. 17-21SYGC/S530-E2/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered.