Datasheet

ManualsBrandsEverlight Electronics ManualsLEDsSMD LED 632nm 1206 285mcd 25mA

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 1 of 10

Device No:DSE-0001603 Prepared date: 29-May-2009 Prepared by: Liu guosheng

Technical Data Sheet

1206 Package Chip LED with Inner Lens

11-21/R6C-AR2S2B/2T

Features

․Package in 8mm tape on 7〞diameter reel.

․Compatible with automatic placement equipment.

․Compatible with infrared and vapor phase reflow

solder process.

․Mono-color type.

․Pb-free.

․The product itself will remain within RoHS complaint version

Descriptions

․The 11-21 SMD LED is much smaller than lead

frame type components, thus enable smaller board

size, higher packing density, reduced storage space

and finally smaller equipment to be obtained.

․Besides, lightweight makes them ideal for

miniature applications. etc.

Applications

․Backlighting in dashboard and switch.

․Telecommunication: indicator and backlighting in

telephone and fax.

․Flat backlight for LCD, switch and symbol.

․General use.

Device Selection Guide

Chip

Part No.

Material

Emitted Color Resin Color

11-21/R6C-AR2S2B/2T AlGaInP Brilliant Red Water Clear

Summary of content (10 pages)

PAGE 1
Technical Data Sheet 1206 Package Chip LED with Inner Lens 11-21/R6C-AR2S2B/2T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free.
PAGE 2
11-21/R6C-AR2S2B/2T Package Outline Dimensions - + Notes: The tolerances unless mentioned are ±0.1, unit=mm. Everlight Electronics Co., Ltd. http://www.everlight.com Rev.
PAGE 3
11-21/R6C-AR2S2B/2T Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA IFP 60 mA Power Dissipation Pd 60 mW Electrostatic Discharge(HBM) ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Peak Forward Current (Duty 1/10 @1KHz) Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec.
PAGE 4
11-21/R6C-AR2S2B/2T Bin Range Of Dom. Wavelength Group A Bin Min Max E4 617.5 621.5 E5 621.5 625.5 E6 625.5 629.5 E7 629.5 633.5 Unit Condition nm IF =20mA Unit Condition mcd IF =20mA Unit Condition nm IF=20mA Bin Range Of Luminous Intensity Bin Min Max R2 140 180 S1 180 225 S2 225 285 Bin Range Of Forward Voltage Groups B Bin Min Max 0 1.75 1.95 1 1.95 2.15 2 2.15 2.35 Notes: 1.Tolerance of Luminous Intensity: ±11% 2.
PAGE 5
11-21/R6C-AR2S2B/2T Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. http://www.everlight.com Rev.
PAGE 6
11-21/R6C-AR2S2B/2T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned are ±0.1, Unit = mm. Everlight Electronics Co., Ltd. http://www.everlight.com Rev.
PAGE 7
11-21/R6C-AR2S2B/2T Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned are ±0.1, Unit = mm. Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Everlight Electronics Co., Ltd. http://www.everlight.com Rev.
PAGE 8
11-21/R6C-AR2S2B/2T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level : 90 % LTPD : 10 % Test Sample No. Items Test Condition Hours/Cycles Size Temp. : 260℃±5℃ 1 Reflow Soldering 22 PCS. 6 Min. Min. 5sec. 2 3 4 5 Ac/Re 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS.
PAGE 9
11-21/R6C-AR2S2B/2T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.
PAGE 10
11-21/R6C-AR2S2B/2T 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered.