NVR/DVR/Hybrid NDVR User Manual Ver. 11.350. A112.
NVR/DVR/Hybrid NDVR System TABLE OF CONTENTS TABLE OF CONTENTS ........................................................................................................................1 INSTALLATION ....................................................................................................................................7 Remote Desktop Tool ..............................................................................................................................................
NVR/DVR/Hybrid NDVR System 2.2.7 Withdraw the Record ................................................................................................................................ 35 2.3 Search Mode...................................................................................................................................................... 36 2.3.1 Unusual Event-General Motion ............................................................................................................... 36 2.3.
NVR/DVR/Hybrid NDVR System 4.2 Action................................................................................................................................................................... 65 4.2.1 Action - Assign a action type .................................................................................................................. 65 4.2.2 Action Type - On Screen display............................................................................................................. 66 4.2.
NVR/DVR/Hybrid NDVR System 6. E-MAP.........................................................................................................................................101 6.1 Edit Mode .......................................................................................................................................................... 102 6.1.1 Add/Edit/Delete Map ............................................................................................................................. 102 6.1.
NVR/DVR/Hybrid NDVR System 9.5.3 I/O Control................................................................................................................................................. 124 9.6 Playback............................................................................................................................................................ 124 9.6.1 Add Remote Playback Site...................................................................................................................
NVR/DVR/Hybrid NDVR System -6-
NVR/DVR/Hybrid NDVR System INSTALLATION The Installation CD contains the software you need to run the complete system. If you are installing the system on multiple PCs, install the appropriate software for each PC: - Server Application: All functions of NVR/DVR/Hybrid NDVR systems including Main Console, Playback, Remote Live Viewer, Backup, and Verification Tool. - Remote Desktop Tool: The tool to access main console and setup configuration remotely.
NVR/DVR/Hybrid NDVR System Step 1: Select Setuptool.exe to start installation. Step 2: There are 4 system types listed in the System Setup Tool window. Choose one and select Next. IP Surveillance System/Trial System MPEG-4 Hybrid System H.264 Hybrid System Full D1H.264 Hybrid System Note: The Setup Tool will detect the type of capture cards installed on PC and enable the system options automatically. Step 3: Select Next to continue.
NVR/DVR/Hybrid NDVR System COMPLETE SETUP TYPE Installs all program features into the default directory. Check Complete, and then select Next. All program features will be installed. [COMPLETE SETUP requires the most disk space.] CUSTOM SETUP TYPE Allows you to install the system to a preferred directory and select whichever program feature(s) to install. [Recommended for advanced users] Check Custom, and then select Next. Select Change if you wish to modify the installation directory.
NVR/DVR/Hybrid NDVR System Step 8: Select Finish, installation complete.
NVR/DVR/Hybrid NDVR System Remote Desktop Tool Remote Desktop Tool allow user remote to access Main Console System and setup configuration. Step 1: Run Setup.exe from RemoteDesktopViewer to start the installation. Step 2: Select Next in the Install Shield Wizard dialog box. Step 3: Check the option I accept the terms of the license agreement. Select Next. Step 4: Enter your information, select Next. Step 6: Select Complete or Custom setup type.
NVR/DVR/Hybrid NDVR System COMPLETE SETUP TYPE Install all program features into the default directory. Check Complete, and then select Next. All program features will be installed. [Requires the most disk space.] CUSTOM SETUP TYPE Install the system to a preferred directory. Select program feature(s) to install. advanced users] Check the option Custom, select Next. Select Change to select folder setup will install files. Select the features setup will install.
NVR/DVR/Hybrid NDVR System DVR Driver Installation Driver Install Tool help user to auto detect type of capture card and install corresponding drivers. Step 1: Run InstallDri.exe to start the installation. Step 2: In the Driver Setup dialog box, select Next. Step 3: Check I Agree to continue. Step 4: Installing driver. Step 5: Click Finish after installing the system completely, and then choose to reboot now or later.
NVR/DVR/Hybrid NDVR System - 14 -
NVR/DVR/Hybrid NDVR System PDA Client Installation Step 1: Connect PDA device to the PC. Step 2: Run Setup.exe from the directory/PDAClient to install PDA Client. Note: If you do not have Microsoft® ActiveSync installed, a message will appear “Cannot find ActiveSync, install ActiveSync and run installation again”. Step 3: Check that the client application is installed completely in PDA device. Smart Phone Client Installation Step 1: Connect Smart Phone device to the PC. Step 2: Run Setup.
NVR/DVR/Hybrid NDVR System - 16 -
NVR/DVR/Hybrid NDVR System Quick Start Execute Main Console Step 1: Go to Start > All Programs > Surveillance System > Main Console to execute Main Console. Step 2: Enter your own password into the edit box, enter it again for double confirm and then click on OK. Activate IP Camera License(s) Step 1: Open License Manager Tool in Config menu. Step 2: Select Activate tab, check the PC in Online network environment. Step 3: Insert the SN, SN file or dongle to activate license.
NVR/DVR/Hybrid NDVR System Add IP camera(s) Step 1: Execute Main Console. Step 3 Step 2: Type in user name and password and log in to the system. Step 3: In Main Console, go to Config and select Setting to obtain the Setting panel. Step 4: Go to Camera tab. Note: If the IP camera supports UPnP, follow step 5. Otherwise, follow step 8. Step 5: Click on Search to detect IP cameras under this local area network (LAN). Note: The Search function is available only when the IP cameras support UPnP.
NVR/DVR/Hybrid NDVR System Set Schedule Step 1: Execute Main Console. Step 2: Type in user name and password. Step 3 Step 3: Select Schedule. Step 4: The default schedule is “always record' when a camera is newly inserted. Step 5: Choose a camera and then select Configure or just double click on the schedule bar to modify the recording mode. Step 6: Select OK to update the recording schedule. Step 7: Select OK to go back to Main Console.
NVR/DVR/Hybrid NDVR System Start Recording & Smart Guard Step 1: Execute Main Console. Step 3 Step 2: Type in user name and password and log in the system. Step 3: Click on Start. Step 4: Click on Start Recoding Schedule and Start Smart Guard System to enable the two functions. Step 4 Playback Step 1: Execute Main Console. Step 2: Type in user name and password and log in the system. Step 3 Step 3: Click on Playback. Step 4: In Playback, click on Date Time Search Dialog.
NVR/DVR/Hybrid NDVR System 1. Main Console This is the main operating system - to activate schedule recording, setup smart guard and configure system setting.
NVR/DVR/Hybrid NDVR System 1.1 User Interface Overview Information Window Exit Minimize Screen Division Exit: Shut down the Surveillance System or log out current user. Minimize: Minimize the Main Console window. Screen Division: Allocate the sub-screen display by clicking on the desired layout icon. To switch to single camera display, double click on a particular sub-screen. Double click on the screen again to regain previous screen division layout.
NVR/DVR/Hybrid NDVR System Stop Note: To customize Information about window’s setting, go to Config - Setting - General - Status Display. Select Advanced Setting for further information like Temperature, Fan speed, System Resource and Network Utilization. Start Playback Schedule Guard Config Start: Click on the Start icon and select from the drop down menu to activate/ deactivate: (a) Recording Schedule System, (b) Smart Guard System, or (c) Counting Application.
NVR/DVR/Hybrid NDVR System Add/edit type(s) of events that you want to detect; setup action(s) responding to events. See Guard on page 57 for detail. Config: Select from the drop down menu to modify the general settings, user account settings, save/ load configuration settings, open License Manager, edit counting application and POS application, access log viewer and backup files, or setup network services. See Config on page 70 for detail.
NVR/DVR/Hybrid NDVR System Note: You can define up to four groups of auto patrol. To start or stop, click on Go to Preset Point in the Main Console, and select Start Patrol or Stop Patrol.
NVR/DVR/Hybrid NDVR System 1.3 On Screen Menu Right click on the camera screen and get the On Screen Menu, from which you can quickly adjust the setting of camera. 1.3.1 Camera Setting Click to go to the camera setting page for configuration. See page Error! Reference source not found.Error! Bookmark not defined. for details. 1.3.2 Enable Move/Area Zoom With cameras that support PT function, click the Enable Move function to adjust the current camera’s view by clicking on the display screen.
NVR/DVR/Hybrid NDVR System 2. The settings will apply to all divisions and also the right column of monitor display. 1.3.10 Enable Digital PTZ To enable the PTZ functions of the camera, select the Enable digital PTZ option. Use mouse wheel or click on the + and – signs to zoom in and zoom out on the camera, or drag a rectangle to enlarge the area. The square flashing on the video grid indicate the correspondent view ratio of the camera. 1.3.
NVR/DVR/Hybrid NDVR System Note: This camera list is also available at the monitor display tab from the Config/Setting window. monitors can have two independent lists.
NVR/DVR/Hybrid NDVR System video. Export Period: indicates the period of video you desire to export. Default is set as available play period. Tool: Adjust to original video resolution button: Press to adjust the video to original video resolution. Audio button: Press to turn on / off the audio. POS button: Press to enable / disable POS transaction data overlay. 1.5.
NVR/DVR/Hybrid NDVR System If the selected video sequence uses multiple image resolutions (CIF, 2CIF, 4CIF, etc.) or multiple video format(MPEG-4, M-JPEG, H.264), the exported video sequence will create separate export files every time the resolution changes.
NVR/DVR/Hybrid NDVR System 2. Playback Watch the recorded video, view and/or search for unusual events and recorded system information.
NVR/DVR/Hybrid NDVR System 2.1 User Interface overview: Search Mode Screen Divisions Open Record Enhancement /Post Processing Tool Exit Minimize Scroll Bar Information Window Audio Volume Control Save Image Print Minimize: Minimize the Playback console. General Setting Backup Export Video / Audio Log Viewer Exit: Shut down the Playback console. Scroll bar: Indicates the status of the playing video; drag it to where you want to review.
NVR/DVR/Hybrid NDVR System Zoom: Zoom in and zoom out. On Screen Menu: Toggle Fullscreen: Select to view cameras under full screen. Press “Esc” or right click to go back to original view. Enable ImmerVision PTZ: Adjust PTZ in PTZ mode. (Depend on device) ImmerVision Lens Setting: Select the mode of lens, original, PTZ mode, Quad mode and Perimeter mode.
NVR/DVR/Hybrid NDVR System 2.2 Open Record / Date Time Search Dialog Click on the Open Record / Date Time Search Dialog button withdraw the video record that you want to review. to access the Date-Time Panel and 2.2.1 Date Time Panel 2.2.2 Record Display Window The record display window shows the information of the available video clips. It may show in calendar or list control view. For further details about how to modify the record display window view, see page 46.
NVR/DVR/Hybrid NDVR System * Note: Some event types will not be available under Lite License. 2.2.6 Time Table Utilize the the scale bar to modify the scale of the time table. Selecting “Show Records” makes Time Table show the period of recording data as below: icon to select all channels; also utilize the icon to deselect all channels. Finally, utilize Show Records Selecting Show Event Log makes Time Table show the time of event detection like below: Show Event Log 2.2.
NVR/DVR/Hybrid NDVR System Step 4: Check the Enable Preview option to get the preview of the video you select. Step 5: Click the camera name to increase or decrease cameras you want to playback. Step 6: Click OK when setting is complete. 2.3 Search Mode Click on the Search Mode icon to obtain the Intelligent Search Tool panel. * This feature is not available under Lite License. Intelligent Search Tool Panel: Click on the Search Mode icon to open the Intelligent Search Tool.
NVR/DVR/Hybrid NDVR System can lower the Interval to avoid the alarm being triggered by a pedestrian. 2.3.3 Unusual Event-Missing Object Missing Object: Detection of selected objects removed from the defined area on the screen. Define detection zone: Left click and drag to draw a detection zone. The search tool will detect selected objects removed in this zone. Sensitivity: Modify the sensitivity setting with the slider.
NVR/DVR/Hybrid NDVR System Cue In Cue Out Step 3: Click on the Save Video button file name and click SAVE. , choose the folder where you want to save the file at, enter the Step 4: Set the Export Format (ASF recommend) and set the Use Profile. ASF – more efficient than AVI format. [Recommended format] AVI (Microsoft Video 1) – Supports Windows Media Player with Vista & XP, quality may be poorer than recorded video by transcode process.
NVR/DVR/Hybrid NDVR System automatically save the image file at page 46.) 2.7 Print Click on the Print button the video you choose. to print the current image of Print Content: Print the image from the current selected channel or all the channels shown on the screen. Select to print original view or selected region on camera. Page Setting: Set to print the image with original size or fit to page. Align image to Top, Center, or Bottom. Set 2.
NVR/DVR/Hybrid NDVR System - 40 -
NVR/DVR/Hybrid NDVR System 2.9 Log Viewer Click on the Log Viewer button to activate the Log Viewer dialog. 2.9.1 Unusual Event View the unusual event history that had been detected by the Smart Guard System. Step1 Step2 Step 4 Step 3 Step1: Choose the type of events you wish to view or select “All” from the drop-down menu to view all types of events.
NVR/DVR/Hybrid NDVR System search period. For a particular data: check the Date box right and indicate the date. For a period: check the DateTime and then enter the date and time. Step 3: Click Search 2.9.3 System Log Step 1 Step 2 Step 3 Select Log Type from the drop-down menu.
NVR/DVR/Hybrid NDVR System 2.9.4 Counting Application Display the history of Counting Application during a given time period. * This feature is not available under Lite License. Step 4 Step1: Select the channel you want to check or select All from the drop-down menu for all channels. Step 2: Select search period. View the events that happened on a particular date or during a given time period by selecting search period. For a particular date: check the Date box right and indicate the date.
NVR/DVR/Hybrid NDVR System 2.9.5 Counting Application (Diagram) Display the Counting Application data in diagram format. * not available under Lite License Step 4 Step1: Select the channel you want to check or select All from the drop-down menu for all channels. Step 2: From the drop-down menu, set up how you would like the diagram to be displayed. You have the options of one day, one month, or one year. Step 3: Select a specific date to make it the start point of the diagram. Step 4: Click Search.
NVR/DVR/Hybrid NDVR System Step 4: Click Search. A link ( ) will appear next to each event time where video is available. By clicking on the link, the video will jump to the point where the unusual event takes place. Step 5: Press the button Export to. Step 6: Type the file name and choose the file format (.xls or .txt). 2.9.7 Export and Backup Log View the Export and Backup Log history that had been operated by local or remote user.
NVR/DVR/Hybrid NDVR System .txt .xls 2.10 Setting Click on the General Setting button and go to Setting for system configurations. Record Display setting: Calendar View: Choose to display records under calendar view. List Control: Choose to display records under checklist. Play setting: Play when open: Check the option and set the system to start playing the video clip every time a record is withdrawn.
NVR/DVR/Hybrid NDVR System OSD Setting Enable Camera OSD to display video information on recorded video. Information includes camera name, camera number, date and time. User can also set up OSD font; include the font, size, font color and any font effects desired.
NVR/DVR/Hybrid NDVR System 2.11 Remote Server 2.11.1 Add Remote Playback Site Press the Remote Server Icon or go to setting – server to config remote playback site management to add and setup remote playback sites. Step 1: Enter the IP address or DNS, Port, Username, and Password. Step 2: Click Add to add the server. Step 3: Click OK to exit the “Settings” panel. 2.11.
NVR/DVR/Hybrid NDVR System 3. Schedule Click on the Schedule icon on the Main Console and set up the time duration for video recording on the schedule configuration panel.
NVR/DVR/Hybrid NDVR System 3.1 Day / week Mode Load Camera / Channel Day /Week Mode Schedule Details Day Mode: Schedule the cameras to turn the recorder on and off at the same time every day according to your setting. Week Mode: Allows you to schedule each camera for a different day of the week, additionally, you may assign extra holidays in the “Week” mode Schedule Details: An outline of start time, end time, Record mode, frame rate, quality and resolution.
NVR/DVR/Hybrid NDVR System IPS-1000, IPS-2000, IPS-3000, IPS-4000 series (Analog camera) Mode Format Time Record FPS Quality Resolution Regular MPEG-4 0:00-24:00 Always 30 Normal CIF Office MPEG-4 8:00-20:00 Always 30 Normal CIF Shop MPEG-4 10:00-22:00 Always 30 Normal CIF Highly Secure MPEG-4 0:00-24:00 Always 30 Highest Max Disk Saving MPEG-4 0:00-24:00 Motion 30 Normal CIF Minor MPEG-4 0:00-24:00 Motion 15 Low CIF IPS-5000 series (Analog camera) Mode Fo
NVR/DVR/Hybrid NDVR System 3.1.2 Insert a New Schedule Manually Step 1: Left-click and draw the bar you want add to the time table. The scheduled time will show as a grey bar. Step 1 Step 2 Step 3 Step 4 Step 2: Click the Insert icon and add a new schedule in the Regular Mode, i.e. to record video during the time period you set with 30 FPS, normal video quality, and normal resolution.
NVR/DVR/Hybrid NDVR System Holiday: You may assign holidays where the system will work according to the setting for Sunday. Note: The default Holiday setting will apply Sunday’s settings. For the Middle East region where Friday is a holiday, please adjust setting by right clicking on From…”. and select “Apply Holiday Schedule Custom: You can assign a particular date(s) on which the system will work according to a special schedule(s) different from the others. 3.
NVR/DVR/Hybrid NDVR System 3.3 Encoding Option Original Video Time Option Record Mode Encoded Video Video Encoder 3.3.1 Pre-record/ Post-record Time The pre-record/ post-record function saves the recording data accordingly. For instance, to set up a 5 second pre-record time means the system will start saving the recording data 5 seconds before the event happens. Note: The maximum of pre-record/post record period is 60 seconds. 3.3.2 Record Mode There are four recording modes to choose from.
NVR/DVR/Hybrid NDVR System record on event” to trigger recording. Record on Event: Select this option to start recording at any predefined event, including Smart Guard events, metadata events, digital input events and video analytics from devices. * Some options are not available under NVR Lite License Select this option to obtain the “Select Event” panel. From the Smart Guard list, check the camera events or digital inputs to trigger the recorded action. Click OK.
NVR/DVR/Hybrid NDVR System - 56 -
NVR/DVR/Hybrid NDVR System 4. Guard Click on the Guard button on the Main Console to start the “Event and Action Configuration” panel. You will need to specify an event to be detected as well as set the appropriate action for the system when the event occurs. Note: 1. Event Report: When the crystal ball is red, you can click it to obtain the Smart Guard Event Report and cancel the event(s).
NVR/DVR/Hybrid NDVR System 4.1 Event Insert Event There are 4 sources of events: Camera (video image), POS, Digital Input (device connected to your PC) and System (condition of your hardware). You can assign multiple events by following the instructions below. * Note: Some event types will not be available under Lite License. 4.1.1 Camera Event - Assign a Camera Event Step 1: Select a camera and click “Insert Event” icon. .
NVR/DVR/Hybrid NDVR System Function 2 : Click the red crystal ball to obtain the Smart Guard Event Report than cancel the event(s). Cancel event after timeout xx seconds: Enable checkbox and set the timeout seconds to cancel the event after a specific time whether the event disappears or not. 4.1.3 Camera Event - Signal Lost Detect the loss of video signal from camera. 4.1.4 Camera Event - General Motion - Detect any movement in the defined detection zone.
NVR/DVR/Hybrid NDVR System 4.1.5 Camera Event - General Motion (Device) - Detect movement with motion detectors of devices (IP cameras or video servers). * Note: This function is only available on devices with built-in motion detection. Please refer to the user manual of your device to set up motion detection. Start Simulation Click to test if motion detection is set up correctly. Go to Web Interface Click to go directly to device web page for configurations. 4.1.
NVR/DVR/Hybrid NDVR System briefcase and define it as the object size. Remove the briefcase and then activate the Smart Guard function on the Main Console. The system will consider everything on the screen normal when you click Start to activate the monitor function. Start Simulation: Click the Start Simulation button and test the function on the preview screen. 4.1.7 Camera Event - Missing Object Alarm triggers when an object disappears in the defined area on the screen.
NVR/DVR/Hybrid NDVR System 4.1.8 Camera Event - Lose Focus This function alarms you when any of the cameras is losing focus and has blur image. Sensitivity Interval Ignore Lighting Start Simulation Alarm Event Option: Sensitivity: Click and move the slider control to the right to increase sensitivity so that a relatively small movement will trigger the alarm. Move the bar to the left to reduce the sensitivity of movement detection.
NVR/DVR/Hybrid NDVR System Alarm Event Option: Sensitivity: Click and move the slider control to the right to increase sensitivity so that a relatively small movement will trigger the alarm. Move the bar to the left to reduce the sensitivity of movement detection. Set up an appropriate Sensitivity value will reduce the chance of false alarm. For example, you can lower the Sensitivity to avoid the alarm being triggered by a swinging tree in the breeze.
NVR/DVR/Hybrid NDVR System Step 1 Step 2 Step 1: Click and highlight Digital Input on the event type list, and then click the Step 2: Select the device that is connected to your system. Insert Event icon. 4.1.12 System Event - Assign a System Event Step 1 Step 2 Step 1: Click and highlight System on the event type list, and click the Step 2: There are four events, select the event you want to detect. Insert Event icon. 4.1.
NVR/DVR/Hybrid NDVR System 4.1.16 System Event – Network Congestion This function alarms you when network bandwidth is overloaded. Current Status: Shows you the current Total Upload/Download bit rates. Options: Fix maximum bit rate (Kbps) for High Upload/Download Bit rate Alarms. System Health Unusual Resource Depleted 4.1.16 System Event – TV-Out * Note: This function is not available if there is no IPS-7108/7116 card installed. Pop-up video to TV-Out monitor on event. 4.2 Action 4.2.
NVR/DVR/Hybrid NDVR System Step 1 Step 2 To insert a new action: Step 1: Choose an event and click the insert action icon . Step 2: There are 10 types of actions, select the actions you want and then click OK. 1. On Screen Display 6. DI/DO 2. Play Sound 7. Send a SMS Message 3. Send E-mail 8. Send to Central Server 4. Phone Call 9. Send snapshot to FTP 5. PTZ Preset Go 10. Popup E-Map on event. * Note: Some actions will not be available under Lite License.
NVR/DVR/Hybrid NDVR System 4.2.4 Action Type - Send E-mail The system will send an E-mail immediately to given accounts indicating the type of event, the time, and attaching a picture taken while the event is detected. Step 1: Select the “Send E-mail” action and then click OK. Step 2: The responding window will popup to Select Contact, type the message to append. (You can choose more than one contact). Edit Address Book: Insert the contact information here. Note: 1.
NVR/DVR/Hybrid NDVR System Step 1: Select the “DI/DO” action and then click OK. Step 2: The responding window will prompt user to Select Digital Input Module. Click the “DI/DO” indicator to modify the setting. Step 3: Select the device that is connected to your system, that is, the PC you are working with. You can enable the Automatically Popup I/O Control Panel check box to obtain the correspondent panel to monitor the I/O status.
NVR/DVR/Hybrid NDVR System Please refer to I/O settings for details. 2. To define an FTP server, go to Config > Setup > Hotline. See Configuration at page 81 for detail. 4.2.11 Action Type – Popup E-Map on Event The system will auto popup E-Map window and show the assigned map and indicator. * Note: This function is not available under Lite License. Step 1: Select the “Popup E-Map on Event” action and then click OK. Step 2: The responding window will popup to Popup e-map on event.
NVR/DVR/Hybrid NDVR System 5. Configuration Config Click on the Config icon, select from the drop-down menu and open the Configuration panel. Modify the setting and access License Manager, Counting application, POS application, Log viewer, Backup, Network Services. Select Save/Load Configuration to save/load all the settings. * Counting Application and POS Application not available under Lite License. * Video Source function available only with MPEG-4 software compression captures devices.
NVR/DVR/Hybrid NDVR System 5.1 Setting – General Storage Status Display Startup Miscellaneous Audio Preview Auto Reboot 5.1.1 Startup Check the Main Console box to execute Main Console system when windows startup.
NVR/DVR/Hybrid NDVR System Note: 1. The system will detect the storage space of default location firstly, if the default storage space is exhausted, the video will be stored to the next directory. 2. If all the status of locations exceeds the storage rule, the system will start recycling in an hour progress. Only keep video for: Delete the video records that are older than the number of days set.
NVR/DVR/Hybrid NDVR System Note: Insert the username and password of MainConsole again when clicking the minimized MainConsole icon in notification area of windows task bar to start monitoring. Synchronize video frames: Select to avoid image tearing problems that may occur while CPU loading is increased. DDNS Service: Dynamic Domain Name Server (DDNS) function allows you to use Live View or Web View to connect to the Main Console through Internet event if you have a dynamic IP address.
NVR/DVR/Hybrid NDVR System - 74 -
NVR/DVR/Hybrid NDVR System 5.2 Setting - Camera Config Search Insert Config Delete 5.2.1 Add Camera Four function buttons will be included in the Setting/Camera panel if you have our Hybrid Surveillance System license for IP camera. Search: Click on the Search icon for the Search IP Camera panel. The system will start scanning automatically; click on the Stop Scan button to stop scanning any time. Fill in the user name and password for each IP camera found and click OK to add it to the camera list.
NVR/DVR/Hybrid NDVR System settings with the Setting panel. See following part (IP Camera / Video Server Setting panel) for detail. 5.2.2 IP Camera / Video Server Setting panel Network Device Description Network: Fill in required info of the Network field (including Name, IP Address, Http Port, User Name, Password and Protocol) referring to the instruction provided by the camera manufacturer. Check “Use DNS” to use domain name instead of IP address.
NVR/DVR/Hybrid NDVR System such as camera position. Stream Profile: Stream profiles are pre-defined to preferred settings which will respond from the query of the remote live view function. Each profile has different Format, Frame, Resolution, Quality and Bit rate (Kbps) settings. Stream Profile Options Note: The types of stream profiles and options will differ among stream sources.
NVR/DVR/Hybrid NDVR System 5.3 Setting - I/O Device Device Setting I/O Device Setting List of devices Input Monitor Output Monitor I/O Device Setting: Module Setting: Name the module device and ID that has been connected to the digital input/output device(s) to your system. Device: This column displays the device(s) already installed to the system. ID: Select the number of the I/O port to which you plug the ribbon cable. Input Monitor: The device(s) is turned on if the dot is red.
NVR/DVR/Hybrid NDVR System Advanced Setting Miscellaneous Install PTZ cameras and follow the instructions of the camera manufacturer. A PTZ camera is usually connected to the PC with RS-485/RS-422. Check the box on the camera list to activate the PTZ control function of a PTZ camera. Basic Setting: Select the camera model, com port, baud rate, and address according to your PTZ camera.
NVR/DVR/Hybrid NDVR System Step 2: Type the Preset Number. Step 3: Select the Preset Type. Step 4: Press the buttons to Add, Delete, or Update preset setup.
NVR/DVR/Hybrid NDVR System 5.5 Setting – Hotline Configure the settings of various contacts or devices, including E-mail, FTP, GSM modem and Telephone calls which will be triggered upon event detection. E-mail: Input the following information: Server, Port, and Sender’s E-mail address, E-mail’s subject title, Body content and SSL option for encrypted transmission. Click on the Send Test Mail button to test the settings.
NVR/DVR/Hybrid NDVR System 5.6 Setting - Address Book Manage the address book from which you may send out a phone call or an E-mail when an unusual event is detected. 5.7 Setting – Monitor Display Playback Option Cameras List Auto Scan Layout Playback Option: Execute Playback on the secondary monitor by checking the box. Make sure to adjust the display setting of your computer in advance to avoid system error.
NVR/DVR/Hybrid NDVR System 5.8 Setting – Joystick * Note: This function is not available under Lite license. Function Import Export Parameter Default Function: You can choose the function from the drop-down menu for the button of the joystick. Note: Following is a complete list of all log types: 1. N/A 9. Start/Stop Auto Scan 2. Goto Preset Point 10. PTZ Speed Up 3. Goto Camera 11. PTZ Speed Down 4. Goto Previous Camera 12. Zoom Wide 5. Goto Next Camera 13. Zoom Tele 6. Switch Screen Layout 14.
NVR/DVR/Hybrid NDVR System Import: You can import the setting of the joystick.
NVR/DVR/Hybrid NDVR System 5.9 User Account Setting Configure all user accounts under this settings page. Note that this page is only accessible by the default admin account. User Add new users and modify or remove existing users. You may choose to add Basic Users directly in the system or import users from MS Active Directory (MSAD) as Windows Users. *Note: Please remember to add your Windows login AD user account to the local PC's administrators user group.
NVR/DVR/Hybrid NDVR System Windows Users Click on to add/remove/synchronize Windows Users. Select User Check users or folders under Select Active Directory user(s) and click OK to add Windows Users. Click Select All to check all available users and folders, or click Deselect All to uncheck all users.
NVR/DVR/Hybrid NDVR System Automatic Synchronize Windows User Setting Instead of manually adding and updating Windows users, you may also configure the system to automatically synchronize all Windows users at a specific period. Click on to do this. Automatically synchronize Windows users: Check to enable automatic synchronization. Synchronized period: Configure the synchronization to start every ___ days. Synchronized time: Define at what time the synchronization should start.
NVR/DVR/Hybrid NDVR System 5.10 Auto Backup Setting Configure your system to automatically backup video data on a daily or weekly basis. * Note: This function is not available under NVR Lite license. Auto Backup Config: Configure auto backup settings on this page. Enable Schedule Backup: Check to enable backup process. Select Camera(s) to Backup: Choose all channels to backup. Option Location: Define backup route. Backup Playback System: Check to backup the playback application with each process.
NVR/DVR/Hybrid NDVR System Auto Backup Statistic: Shows statistics on current or latest backup status. Click Refresh to update. Refresh Current Backup Status: Idle: not active or awaiting next backup process Backup…: Backup under process Retry…: Previous backup failed, awaiting retry Next Backup Start Time: Scheduled time for next backup process Next Retried Process Time: Scheduled time for next backup retry process. under Backup.
NVR/DVR/Hybrid NDVR System 5.12 Save/ Load Configuration The Save/ Load Configuration function allows system users to save any specific setting as a CFG (config) file. You may save several different CFG files at a time. Save Configuration: To save a specific setting, go to Config - Save/Load Configuration - Save. In the popup window, type in the file name and then save it as a CFG file. Load Configuration: To load a specific setting, go to Config - Save/ Load Configuration - Load.
NVR/DVR/Hybrid NDVR System 「TV-Out Setting」 window appears. TV-Out Monitor Auto Scan Camera Monitor Display TV Adjustment Miscellaneous TV-Out Monitor: Display all IPS-6000/7000/7100 series cards installed in this computer, choosing IPS-7100 series one to click on for TV-out function then users can start to edit the right parts. Camera: Displays a list of all cameras. Monitor Display: Modify the cameras shown on Monitor Display in the right window.
NVR/DVR/Hybrid NDVR System 5.14 Counting Application Count objects, people or vehicles passing through pre-defined detection zones. To access this page, login with admin account or user account with privilege of configuring main system. * Note: This function is not available under Lite license. Camera List Operation Start Simulation Options Runtime Camera List: Select which camera would enable counting application. Operation: Define detection zones: Defined the detection zone.
NVR/DVR/Hybrid NDVR System 5.15 Video Analytics – Privacy Mask Mask your video with dark areas to protect your privacy. To access this page, login with admin account or user account with privilege of configuring main system. * Note: This function is not available under NVR Lite license. Privacy mask settings will apply to local and remote live view, web live view, local playback, remote playback and web playback.
NVR/DVR/Hybrid NDVR System 5.17 Network Service There are 5 types of network services: Live streaming server, Remote playback server, 3GPP service, Remote Desktop, and Central Management Service. From the Main Console, go to Config - Network Service to obtain the Network Service panel. An icon shows for each network service in the information window of Main Console when started. See 1.1 User Interface Overview for details. LiveView Playback 3GPP Desktop CMS Start Stop 5.17.
NVR/DVR/Hybrid NDVR System Options: Adjust the setting only when the server is stopped. Port: Assign a port for the clients to connect to your system via Remote Live Viewer. Default port is 5150. Maximum Connections: Number of connections that are allowed to connect to the system. Default is 16 channels and maximum is 128, one camera video counts as one connection. Use Default Web Server: Activate the Web server by checking the box; clients will be able to watch live video via Internet Explorer.
NVR/DVR/Hybrid NDVR System Performance Total bit rate Individual Camera bit rate information Live Streaming Server log information 5.17.2 Remote Playback Server When starting the remote playback function, the system allows remote users to log in to the specific computer and withdraw data files that are stored on it. As system administrator, user could be able to monitor the accounts logging in to maintain the system efficiency.
NVR/DVR/Hybrid NDVR System Client list: User Count: Show the number of users that are connecting to system. Kill Client: Highlight an IP address and click on the “Kill Client” button to block the client from your client list. Kill All Clients: Click on this button and then block all the clients logging to your system. Service: Server Status: Click on Start/Stop to turn on/off this option. Options: Adjust the setting only when the server is stopped.
NVR/DVR/Hybrid NDVR System 5.17.3 3GPP Service When starting the 3GPP service function of your computer, the system allows remote users to log in and view cameras that are connecting to it with 3GPP supported mobile phone. See Appendix A for more details about 3GPP Service. Client list Service Options Client list: Client Count: Show the number of channels that are connected to system. Service: Server Status: Click on Start/Stop to turn on/off this option.
NVR/DVR/Hybrid NDVR System Options: Port: Assign a port for Desktop tool to login and configure system. Disconnect idle client after (300~3600 sec): Auto disconnect the on-line user who idled more than set period. Authentication: Enabling this option would only allow admin account to use Desktop tool to login system. Service: Server Status: Click on Start/Stop to turn on/off this option. 5.17.5 Central Management Service * Note: This function is not available under Lite license.
NVR/DVR/Hybrid NDVR System NCS Servers and maximum is 16. 5.18 Help Click Help to connect to FAQ of website http://support..com/mediawiki/index.php/Main_Page . 5.19 About Main Console Go to About Main Console for detailed system and license information. 5.20 Video Source (For system with MPEG4 capture device only, not supported under Lite license) Step 1: Go to Video Source to adjust the Video Standard to NTSC or PAL. Step 2: Adjust the maximum Video Resolution for all analog cameras.
NVR/DVR/Hybrid NDVR System 6. E-Map With E-Map, users can easily track the actual location of an occurring event, at the moment it happens. The arrow and lightning icons on E-Map represent cameras and I/O devices. These icons will turn red once they are triggered by alarms. To launch the E-Map application, simply click on Start and select Open E-Map from the start menu for the E-Map window.
NVR/DVR/Hybrid NDVR System 6.1 Edit Mode All E-map modifications must be configured in Edit Mode. Function button Edit mode/ Operate mode Switch button 6.1.1 Add/Edit/Delete Map Add E-Map: Step 1: Click on the switch button to switch to Edit mode. Make sure all devices are connected and setup properly. Step 2: Right click on the Map icon in device and map list to obtain the option menu to add map, or just click “Add Map” button to obtain the “Map Config” dialog.
NVR/DVR/Hybrid NDVR System 6.1.2 Add/Rotate/Delete Device Indicator Add Indicator: Step 1: Make sure you are in Edit mode and all devices are connected and inserted. Step 2: Click on the “ Map” icon to go to the desired map layer. Step 3: Please make sure the map you want is displayed. Select device from the list and directly drag a device to the desired location on the map. Note: Different devices are symbolized by different indicators. - Camera indicator, - digital Output indicator, -POS indicator.
NVR/DVR/Hybrid NDVR System 6.2.2 E-Map picture This window will show the map layer and indicators. Device Indicator: Select device indicators from the Device and Map Tree list for related information and to preview video. Map indicator: Selecting a map indicator will bring you to that map layer. To return to an upper layer, right click on the map and select UP or click on the map layer. 6.2.3 Information and Preview windows This window will show the related information of each indicator.
NVR/DVR/Hybrid NDVR System screen mode of E-Map.
NVR/DVR/Hybrid NDVR System 7. Log Viewer View the history and export reports of unusual events detected by the Smart Guard System. To launch Log Viewer, simply click on Config and select Log Viewer from the menu.
NVR/DVR/Hybrid NDVR System 7.1 System Log Step 1 Step 2 Step 3 Step1: Choose the type of event you want to check or select All from the drop-down menu for all types of events. Select Log Type form the drop-down menu.
NVR/DVR/Hybrid NDVR System Step 3: Click Search 7.3 Unusual Event Step1 Step2 Step 4 Step 3 Step1: Choose the type of events you wish to view or select All from the drop-down menu to view all. The types of Unusual Events include General Motion, Foreign Object, Missing Object, Focus Lost, Camera Occlusion, Signal Lost, Disk Space Exhausted, System Health Unusual, Digital Input Triggered and General Motion (Device). * Note: Detection of some events is not available under NVR Lite license.
NVR/DVR/Hybrid NDVR System For a period: check the DateTime and then enter the date and time. Step 4 Step 3: Click Search. Step 4: Press the button Export to. Step 5: Type the file name and choose the file format (.xls or .txt). 7.5 Counting Application (Diagram) * Note: This function is not available under NVR Lite license. Display the Counting Application data in diagram format. Step 4 Step1: Select the channel you want to check or select All from the drop-down menu for all channels.
NVR/DVR/Hybrid NDVR System For a particular date: check the Date box right and indicate the date. For a period: check the DateTime and then enter the date and time. Step 4: Click Search. A link ( ) will appear next to each event time where video is available. By clicking on the link, an instant playback window will pop up to show recorded video Step 5: Press the button Export to. Step 6: Type the file name and choose the file format (.xls or .txt). Step 5 7.
NVR/DVR/Hybrid NDVR System 8. Backup The backup function saves recorded video and other log information. Backup files may be reloaded on any PC with the Playback System installed. Follow the instructions below for more information on obtaining backup files.
NVR/DVR/Hybrid NDVR System 8.1 Backup Recorded files Step 1 Step 2 Step 3 Step 1: Add (Remote) Backup Site: Press the “Remote Server ” button to go to remote backup site management to add and setup the backup site. Enter the IP address or DNS, Port, Username, and Password. Click Add to add the server. Click OK to exit the Setting panel. Step 2: Access (Remote) Backup Site: Click on the icon and insert the username/password of the remote server to access the backup Site.
NVR/DVR/Hybrid NDVR System Step 8: If there is any data period not wanted, click Remove Period to remove the data period on the backup list. Step 8 Step 9 Step 9: Click the Backup icon to obtain Backup panel. Step 10 Step 11 Step 12 Step 10: Summary: Check the summary section to see the size of the file(s). Step 11: Media: Choose the path you want to save the file or burn the file into a CD (direct CD burning for Windows XP only), DVD or on Hard Disk.
NVR/DVR/Hybrid NDVR System Step 3: Click on the Delete icon and delete all the data in the backup list from the database. Note: Deleted video cannot be recovered.
NVR/DVR/Hybrid NDVR System 9. Remote Live Viewer With the Remote Live Viewer console, remote users may watch up to 128 channels real-time video from remote live streaming servers. * Note: Maximum 32 channels under Lite license.
NVR/DVR/Hybrid NDVR System 9.1 Setting Click General Setting to obtain setting dialog. General Setting 9.1.1 General Setting Audio preview: Enable audio on active channel: Select to enable audio streaming on active channel. Miscellaneous: Synchronize video frames: Select to avoid image tearing problems that may occur while CPU loading is increased. 9.1.2 Server setting Server List Step 1: Enter the Server Name. Step 2: Enter the Address, Port, User Name, and Password to log in the server.
NVR/DVR/Hybrid NDVR System To change the setting, select a server on server list and click “Update” after modify setting. To remove the server, select a server on server list and then click “Delete”. 9.1.3 Group Setting Allocate different cameras into each appointed group. * Note: Cameras under Lite license cannot be included in a group with other servers. Step 1 Step 2 Step 4 Step 3 Step 1: Log in to all the servers that contain the camera(s) you would like to put into the group(s).
NVR/DVR/Hybrid NDVR System Stream profile: List differs according to different types of video inputs and licenses. Auto: The system will adjust the stream type automatically to fit different screen divisions. Recoded: The system will follow the stream profile set in Main Console >Schedule > Encoding Options. High / Normal / Low/ Minimum / H.264 (IPS-7000s only): The system will follow the stream profile set in Main Console - Setting - Camera - Stream Profile.
NVR/DVR/Hybrid NDVR System 9.1.7 Monitor Display Setting Activate auto scan to rotate the channels/ cameras on screen. Note: For instance, you may select to show only 4 sub-screens on the live viewer while having 16 channels connected to the system. With auto scan function, you will be able to see all 16 channels by turns. Each monitor supports up to an 8x8 layout with auto scan function to show 128 channels. Step 1 Step 2 Step 3 Step 4 Step 5 Step 1: Select the Monitor connected to the system.
NVR/DVR/Hybrid NDVR System Status display: Show recording status: Select it to show the crystal ball with recording status on monitor display. Show camera event: Select it to show the smart guard detected event appointed in Main Console on each channel. Note: To execute this function, need setup on screen display as an action of Smart Guard instant response. Show counting result: Select it to show the counting result appointed in Main Console on each channel.
NVR/DVR/Hybrid NDVR System 9.2 Server/Group/Camera Display a complete list of the server(s), group(s) and camera(s) that are added to the system. Server View: Cameras are listed according to recording server. Group View: Cameras are listed according to customized grouping. Server View Group View 9.2.1 login/logout server Option1: Select a server on the list and click on LOG IN/ LOG OUT to access/ logout the server. Option2: On the server list, right click to obtain menu options. Log In/Log Out Server 9.2.
NVR/DVR/Hybrid NDVR System the menu options. Step2: Select Duplicate Camera and the duplicate camera with green indicator will display below on camera list. Step3: Double click on the duplicated camera to connect and display on screen. 9.3 PTZ Control Control the movement of PTZ cameras. With cameras that support PTZ control, you can move, zoom, patrol, adjust the focus, and set preset points of the cameras. 9.3.1 Preset/ Go Adjust the camera view until satisfied.
NVR/DVR/Hybrid NDVR System The square flashing on the video grid indicate the correspondent view of the camera. 9.4.5 ImmerVision Lens Setting *This feature is not available under NVR Lite License. With cameras that support ImmerVision Lens. Right click on the display screen and select the mode of lens, original, PTZ mode, Quad mode and Perimeter mode. If the lens setting set as Quad, PTZ, or Perimeter mode, the Enable Digital PTZ option would become Enable ImmerVision digital PTZ. 9.4.
NVR/DVR/Hybrid NDVR System 9.4.9 Snapshot The snapshot function copies and captures a specific video image to the clipboard or to save as a bmp file. The snapshot can be customized with/without OSD, metadata information and selectable range after digital zoom in. 9.4.10 Toggle Full screen Switch to view video with full screen display. To disable the function, right click on screen and de-select option or simply press “ESC” to go back to original window. 9.5 Start Monitor 9.5.
NVR/DVR/Hybrid NDVR System - 125 -
NVR/DVR/Hybrid NDVR System 10. Web View Server IP Remote Live Viewer Note: Remote Playback Download Client Pack Make sure the Live Stream Server is enabled. Check 5.14 Network Service for more detail. 10.1 Server IP Start Internet Explorer browser and enter the IP address or DDNS name of the server followed by the connecting port. Example: http://192.168.1.16:8080/ Note: 192.168.1.16 is the IP address of the server. 8080 is the port specified in Use Default Web Server in Network Service. 10.
NVR/DVR/Hybrid NDVR System 11. Utilities A. B. C. D.
NVR/DVR/Hybrid NDVR System A. Verification Tool The Verification Tool verifies whether the data created by the system has been tampered with. It is the process by which a digital watermark (a digital signature) is added to each recorded video frame to ensure its authenticity. There are 3 types of data that can be verified by the Verification Tool: 1. File in (.DAT) (.264) format will be displayed as . 2. File in (.AVI) (.ASF) format will be displayed as . 3. File in (.BMP) (.
NVR/DVR/Hybrid NDVR System window to play , Pause and Stop the file. Note: Preview of (.bmp) (.jpg) format is not allowed. 1.3 Verify Image/Video Step 1: Select single or multiple files for verification. Step 2: Click “verify ”to start verification. Step 3: The verification result will show on the watermark column. If a file was tampered with, it will show . If a file passes verification, it will show .
NVR/DVR/Hybrid NDVR System B. License Management Tool The license of the software should be registered before you start using the Intelligent Surveillance System. Execute the License Management Tool to activate the license from dongle or serial number included with the software package, or de-activate the license then bring it to another PC to activate it again. Please note different level licenses cannot coexist under one license server.
NVR/DVR/Hybrid NDVR System Transfer Transfer Tab SN status Transfer type Transfer 1.2 Activate/Transfer License 1.2.1 Activate License Activation Online Step 1: Open License Manager Tool. Step 2: Select On line as Activate type. Step 3: Input the SN (Serial number)or Import SN file, and then click on Activate button. Step 4: Restart Main Console if activation is successful. Activation Offline Step 1: Open License Manager Tool. Step 2: Select Offline as Activate type.
NVR/DVR/Hybrid NDVR System Step 4: Save Request file, and then take it to another PC that is connected to the Internet. Step 5: Execute OffLineTool.exe click on Activate button. in the other PC. Input the SN (Serial number) or Import SN file, and then Step 6: Save License file, and then take it to original NVR system. Step 7: Open License Manager Tool again, select Import offline license, then click Import button to activate. Step 8: Restart Main Console if activation is successful. 1.2.
NVR/DVR/Hybrid NDVR System Step 4: Restart Main Console if transfer is successful. Transfer Offline Step 1: Open License Manager Tool. Step 2: Select Transfer Tab, and then check Offline as Transfer type. Step 3: Select SN, and then click Transfer button to transfer SN. Step 4: Save Request file. Restart Main Console if transfer is successful.. Step 5: Copy request file to another PC connected to internet. Step 6: Execute OffLineTool.
NVR/DVR/Hybrid NDVR System re-activate again!! - 134 -
NVR/DVR/Hybrid NDVR System C. Resource Management Tool The Resource Management Tool detects whether the system is operational. Note: For further application of the Resource Management Tool, please refer to page 57 In “Guard” chapter. 1.1 Execute Resource Management tool Step 1 Step 1: Open Resource Report from start menu. Step 2: The Resource Management Tool will appear. 1.2 System Resource Overview System Resource History Diagram Advanced 1.2.
NVR/DVR/Hybrid NDVR System each variable in Vertical Axis; the unit of Horizontal Axis will be displayed as “Per Second”. Vertical Axis Horizontal Axis 1.3 Advanced Resource Report Click the Advanced button to search and export system logs in “Search” tab and obtain the history diagram of an specified period in “Diagram” tab. 1.3.1 Search Step 4 Step 3 Step 1 Step 2 Step 5 Step 1: Choose the system event type, and then select the standard percentage to search system log.
NVR/DVR/Hybrid NDVR System 1.3.2 Display Step 4 Step 5 Step 1 Step 2 Step 3 Step 6 Step 1: Choose the system event type. Step 2: Select the Date/Time to draft history diagram. Step 3: Setup the start time and duration for charting. User can choose “One Day”, “One Hour” or “One Minute” as the duration. Step 4: Click “Display” to start charting, the diagram will be displayed at below column. Step 5: Click “Save” to save the diagram in (*.bmp) format. Step 6: Click “OK” to close the report window.
NVR/DVR/Hybrid NDVR System D. DB Tool The DB Tool repairs database files and Export configurations. Warning: improper use of this DB Tool may cause loss of recorded video. Step 1: Execute DB Tool from program files. Step 1 Step 2: Enter the password of administrator to log in. Step 2 1.1 Repair Database This page has three repair method, Modify Location, Verify Only, and Repair.
NVR/DVR/Hybrid NDVR System Step 3: For add database location, please click on button and use URL to choose location. For remove database location, please choose location form list and click on button to remove location. Step 4: Click on Modify button to modify location. After modification, the Modify Result will show on the panel. Example of modify database: In certain cases where video data needs to be transferred from one PC to another PC, user will need to perform the following: 1.
NVR/DVR/Hybrid NDVR System Step 2: Select the repair Method as Modify Location. Step 3: Check the video location windows. The system will list all video locations in table, but if there are any omit, please use Note: After inserting location, the system will show files count below table. to insert. Step 4: Choose the method of “Verify Only”, and click “verify”. This method will only check the files without modify. Verify result will show how many files broken or missing.
NVR/DVR/Hybrid NDVR System 1.2 Export Configurations This tool is used when user wants to export all system configurations to backup, take to another PC for technical trouble shooting. Step 1: Press “Export”. Step 2: Select the location you want to Export and type the name of the configurations. Step 3: Press “Save” to start to import database.
NVR/DVR/Hybrid NDVR System Appendix A - 3GPP Service How to setup 3GPP streaming connection (using BenQ-Siemens mobile phones) System Configuration DVR / NVR server v2.6 CPU: Memory: Ethernet: Hard Disk: Graphic card: Operating System: Mobile Phone: Intel core2 Duo 1.86 GHz 512 DDR RAM Realtek RTL8168/8111 PCI-E 160GB ASUS Extreme AX550 Windows XP Professional SP2 BenQ-Siemens E81 1.
NVR/DVR/Hybrid NDVR System 1.2 Configuration from 3G Mobile Phone 1.2.1 BenQ-Siemens E81 Step 1: Go to Menu, then Internet Step 2: Select Bookmarks Step 3: Add New Bookmark Step 4: Configure the Adress setting as the following example.
NVR/DVR/Hybrid NDVR System Ex: rtsp://61.216.97.69:554/media00.3gp 61.216.97.69:554 is the IP address of NVR or DVR system Port : port specified in 3GPP Service from NVR or DVR system Step 5: Save the settings and start playing 1.2.2 BenQ P50 Step 1: Connect GPRS Step 2: Download and install the [PLATFORM4] software. Step 3: Execute the Main Console.
NVR/DVR/Hybrid NDVR System Step 8: Go back to PLATFORM4, searching and get the video.
NVR/DVR/Hybrid NDVR System Appendix B – PDA / Smart Phone Client PDA / SP (Smart Phone) Client are only applied for devices with Windows Mobile 5.0 platform or above. See the sections below to find how to install and execute PDA / SP Client. Note: 1. The different between Smart Phone and PDA Client is navigation of operation, user can only control client with phone buttons. 2. The resolution of PDA / SP Client is limited in 240*320 (QVGA). 1.
NVR/DVR/Hybrid NDVR System 1.2.2 Execute and Login Step 1: Make sure your PDA/Smart Phone device is connected to network, and then go to Start - Programs PDA/Smart Phone Client to execute application. Step 2: Insert Address, Port, Name and Password of the server and click on to login. 1.3 PDA/Smart Phone Client Overview There are 3 main pages of Client application: Monitor Preview, I/O Control and System Info. Switch between these buttons to adjust overall configuration.
NVR/DVR/Hybrid NDVR System Camera List: Displays all “snapshots” of channels connected to server as camera list. Click on indicated snapshot to get to display live video. the channel information, and then click on Note: The Screen Division and Refresh option could help to quick find the channel. Screen Divisions Refresh Live Video Display: Live View panel could display “live video”, control PTZ, and snapshot. Click to go back camera list.
NVR/DVR/Hybrid NDVR System I/O Control I/O Device list: Select and monitor the device connected with Server. DI/DO status: Monitor the DI/DO status synchronized with Server, and then click Output button to trigger the DO action. Gray icon indicates the normal status of DI/DO devices. Red icon indicates the alarm status of DI/DO devices. Green icon indicates the synchronization process. 1.3.3 System Info Display the server and client information. Server information includes address, post, and version.
NVR/DVR/Hybrid NDVR System Appendix C – iPhone Browser Live Streaming service can handle requests from iPhone’s Safari browser. use this feature with iPhone devices. This section will guide you how to 1.1 Configuration from Main Console server Step 1: Go to “Config” and select “Network Service” Network Service Step 2: Select “Live Streaming”, and then click “Start”. Note: The “Port” selected here will be the same as the web live view and web playback. Live Streaming Start Port 1.
NVR/DVR/Hybrid NDVR System Appendix D - Remote Desktop Tool How to install Remote Desktop Tool Step 1: Insert the Installation CD. Step 2: Go to Remote Desktop Viewer directly and Run Setup.exe file. How to Start Remote Desktop Tool Step 1: Start - All Programs - Remote Desktop Viewer - Remote Desktop Viewer. Step 2: Enter address, Port, Password of server. Enable the option to use 8 bits color level to show steadier screen. Step 3: Click OK to Start Remote Desktop.
