Speed Dome EPTZ3000/EPTZ3000I USER MANUAL Date: Nov 2008
Table of Contents 1. EPTZ3000/EPTZ3000I OVERVIEW.................................................... 1-3 1.1. Introduction .............................................................................................1-3 1.2. Specifications ..........................................................................................1-5 1.3. Feature .....................................................................................................1-7 1.3.1. Profile of EPTZ3000/EPTZ3000I.................
. EPTZ3000/EPTZ3000I CAMERA SETUP MENU ............................. 3-27 3.1. Structure of the Setup Menu ................................................................3-27 3.1.1. Camera Setup Menu ........................................................................3-28 4. EPTZ3000/3000I FUNCTION SETUP AND OPERATION ................ 4-36 4.1. Manual Control Mode ............................................................................4-36 4.2. Auto Pan Mode .................................
1. EPTZ3000/EPTZ3000I OVERVIEW 1.1. Introduction EPTZ3000/EPTZ3000I, an intelligent high-speed dome camera is ready to secure your property with its omni-directional and exact monitoring. A 30X optical and 8X digital zoom combining with a high-performance chip makes captured images clear and vivid. The other powerful camera functions EPTZ3000/EPTZ3000I equips with: Wide Dynamic makes objects clear in a high illumination background.
Furthermore, the micro control unit enables camera a nimble and exact movement from minimal 0.01°/sec to maximal 360°/sec. It can go to every preset position in 1 second. It also has other advantages such as: 192 preset positions are available. 16 cruise tours can be set, and each tour contains up to 16 positions. Up to 256 speed domes can be supported on a RS-485 bus when all speed domes are controlled by keyboard EKB500. Auto heater and fan to fit all kinds of temperature (outdoor models).
1.2. Specifications Model EPTZ3000 (outdoor) EPTZ3000I (indoor) Pickup Device 1/4'' Vertical double density interline CCD Video Format NTSC or PAL Scanning System NTSC: 525 TV lines, 60 fields/sec PAL: 625 TV lines, 50 fields/sec Picture Elements 768 x 494 ( NTSC ) , 752 x 582 ( PAL ) Horizontal Resolution 520 TVL:Color ; 570TVL:B/W Sensitivity 0.3 Lux/F=1.6 Color ; 0.05 Lux/F=1.
Dwell Time (2 points) 1~127 seconds available Preset Positions 128 positions Running to Position Speed 1~239 grades available Dwell Time at Preset 1~239 seconds available Position Tour 16 groups Tour Point per Group Fan & Heater 16 preset positions Fan & Heater auto starts No ±0.
1.3. Feature 1.3.1.
1.3.2. EPTZ3000/EPTZ3000I Base Board The base board that is on the bottom of the housing connects to power cable, video cable, control cable, alarm cable, fan and heater. In order to connect to cables, the board needs to be taken off, and put back after finishing connecting to all cables. The connectors of cable names are marked on the board in white text. The details of the alarm connector (JP5) are shown on the APPENDIX A.
1.3.3. EPTZ3000/EPTZ3000I Control Board The PCB board with two dipswitches is the control board of EPTZ3000/EPTZ3000I. The two switches are used to set address, protocol, Baud Rate, video format and terminal resistance.
1.4. EPTZ3000/EPTZ3000I Connection 110V AC 24V AC POWER 24V AC / 3.5 A Adapter BNC 1.0Vpp ± 0.2V, 75 Ω Video Out RS485 Tx(+) RS485 Control Line RS485 Tx(-) Alarm 1 EPTZ3000/ EPTZ3000I Alarm 2 Alarm 3 4 ALARM INPUTS Alarm 4 GROUND ALARM OUTPUTS N.C. N.O.
1.5. EPTZ3000/EPTZ3000I Quick Operation Guide (Work with EKB500) EPTZ3000/EPTZ3000I and EKB500 (Keyboard) can work together by using factory default setting. You just need to connect cables by the following steps: 1. Connect the RS-485 cable to EPTZ3000/EPTZ3000I and a keyboard (EKB500). 2. Connect a video cable from EPTZ3000/EPTZ3000I to a monitor. 3. Connect the power to the EPTZ3000/EPTZ3000I and a keyboard (EKB500).
2. EPTZ3000/EPTZ3000I INSTALLATION 2.1. Packing List There are 3 boxes that are housing, bulb and mechanical part with a camera module, one wall mount bracket, one power adapter and one tool packet in the package.
Video Cable A BNC cable is used for connecting an EPTZ3000/EPTZ3000I to a DVR or a monitor. An amplifier may be needed if the video cable is too long. Control Cable Basically, EPTZ3000/EPTZ3000I uses a differential pair to connect to other devices by cascading. A cable that has low signal decline can be used as a control cable. Alarm Cable An alarm cable is not included in the packing list. A suitable wire that has low signal decline can be used as an alarm cable. 2.3.
2.3.1. Address Setting The address code of the EPTZ3000/EPTZ3000I should be set to correspond properly with a control device to control multiple dome cameras. The address codes are made up by the dipswitch SW1 (8 bits) on the PCB board. The 8 bits dipswitch indicates the binary coded of the address, and there are 256 addresses can be selected (0 ~ 255, 28 = 256). It also means that there are up to 256 dome cameras that can cascade on the RS-485 bus.
Switch ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1
Switch 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 ON 1
2.3.2. Communication Protocol Setting The 1st, 2nd and 3rd bits of the SW2 are used to set communication protocol. The factory default protocol is EVF.
Notice: Please make sure the power is off before setting, and restart the EPTZ3000/EPTZ3000I to enable a new value after changing.
2.4. Rack and Speed Dome Installation 2.4.1. Installation Requirements 1. Installation should be handled by a qualified service agent and should comply with all local regulations. Service personnel should expect potential problems such as surface strength, surface material, falling objects, outer breaches, building vibration or other similar conditions. 2. Check for all necessary materials, and ensure if the selected installation location is suitable for the EPTZ3000/EPTZ3000I. 2.4.2.
2. Thread the cable through the hole in the wall mount bracket, and screw in 4 M8 nuts for mounting the bracket. 3. Take off the housing from the packing, and take off the PCB board (4 bolts on it.) inside the housing. Thread the cable through the top of the housing. Fix the housing on the wall mount bracket, and screw in 3 M5 bolts (Hex) on the top of the bracket with the attached Hex Allen wrench to fix the housing.
5. Align the two screw holes on the bottom of mechanical part to the two bolts on the base of the housing, and twist the mechanical part clockwise a little bit in order to engage it with the base. Screw the two bolts on the base, and then connect and fix the connection bus to the PCB board on the mechanical part. Note: The camera module on the mechanical part is very sensitive. Please be careful when installing this part. 6. Remove the lens protection cover before installing the bulb.
Note: In order to protect the bulb from dirt and scrape, please put on the gloves before installing the bulb. 7. Turn on the power, and start to operate the EPTZ3000. Note: When turning on the power, EPTZ3000 will enter self-inspection mode, and carry out a self-testing program. After finishing self-inspection, you can start to operate the EPTZ3000. 2.4.3. EPTZ3000I Dome Camera Installation 1. Take off the housing from the packing, and take off the PCB board (4 bolts on it) inside the housing. 2.
Cut the ceiling RELAY AC24 AC24 RS485 - RS485 + Video - Video + 202 mm JP5 Note: Please notice the polarity of control line. The EPTZ3000I will not work if the polarity of control line is mis-connected. 6. Align the two screw holes on the bottom of mechanical part to the two bolts on the base of the housing, and twist the mechanical part clockwise a little bit in order to engage it with the base.
Note: The camera module on the mechanical part is very sensitive. Please be careful when installing this part. 7. Remove the lens protection cover before installing the bulb. Screw the connection wire to the housing in order to prevent the bulb from being drop down. Align the 2 buttons on the bulb base with the 2 buttons on the housing, and push bulb base to clip the housing.
2.5. Accessories 2.5.1. EPTZ-CPMA: Ceiling Pendant Mount Adapter The pole mount is used for installing a speed dome on the ceiling indoors or outdoors. The extension poles are available for the pole mount. 2.5.2. EPTZ-PMA: Pole Mount Adapter The pole adapter is used for installing a wall mount bracket to a pole indoors or outdoors. 2.5.3.
The corner mount are used for installing a wall mount bracket to a 270° corner of walls indoors or outdoors.
3. EPTZ3000/EPTZ3000I CAMERA SETUP MENU In this section, setup and operation guide of EPTZ3000/EPTZ3000I will be introduced. There are 25 items of the setting menu. However, there is only one line on the line display, so using some combination keys to operate is necessary. 3.1. Structure of the Setup Menu Press MENU to enter camera setup menu. Press Shift + Joystick up/down to change subentries, and right/left to change the setting. Items Option 1. CAM ID ----------------- 2. DZOOM OFF / ON 3.
3.1.1. Camera Setup Menu Press Menu to enter camera setup menu. Press Shift + Joystick up/down to change subentries, and right/left to change the setting. 1. CAM ID： ： The name assigned to the camera. 2. DZOOM： ： Digital zoom enable or disable. ON: Enable a digital zoom. OFF: Disable a digital zoom. ： Focus type, auto focus, manual focus and one push focus are available. 3. FOCUS： AUTO: Auto focus is enabled. MAN: Manual focus is enabled. ONE PUSH: Enable the one push trigger focus mode.
6. S.SHUTTER： ： Slow electrical shutter. In order to enhance the view in the low lux environment, slow shutter allows more light go through the shutter. X4: 4-time slow shutter. X8: 8-time slow shutter. X12: 12-time slow shutter. X16: 16-time slow shutter. X32: 32-time slow shutter. X64: 64-time slow shutter. X128: 128-time slow shutter. OFF: Disable auto slow shutter. 7. DISPLAY : Display the zoom multiple. ON: Display the zoom multiple. OFF: Disable the zoom multiple display. 8.
9. TITLE DISP: Display the title. ON: Display the title. OFF: Disable the title display. 10. ALM-IN1： ： The status of input alarm 1. N.O.: Enable a normal open alarm input. N.C.: Enable a normal close alarm input. NIGHT N.O.: Dome turns to “Night mode” if external contact open. Dome turns to “Day mode” if external contact closed. NIGHT N.C.: Dome turns to “Night mode” if external contact closed. Dome turns to “Day mode” if external contact open. OFF: Disable alarm input. ： The status of input alarm 2. 11.
OFF: Disable alarm input. 14. ALM-IN PRIO： ： The priority of alarms. 1234: The alarm priority is 1>2>3>4. 2341: The alarm priority is 2>3>4>1. 3412: The alarm priority is 3>4>1>2. 4123: The alarm priority is 4>1>2>3. 15. ALM-OUT： ： Duration time of the alarm output. OFF: Disable alarm output. 3 / 5 / 10 / 20 / 30 / 60 SEC: select alarm output’s duration time. LATCH: The alarm output will not stop until there is any operation on keyboard. 16. WDR : Wide Dynamic Range. LOW: Low wide dynamic range.
1/1000: 1/1000 sec shutter for both NTSC and PAL 1/2500: 1/2500 sec shutter for both NTSC and PAL 1/10000: 1/10000 sec shutter for both NTSC and PAL 1/120000: 1/120000 sec shutter for both NTSC and PAL x2: two-time default manual shutter x4: four-time default manual shutter x6: six-time default manual shutter x8: eight-time default manual shutter 18.
OFF: Disable the private zone masking. Press “Enter” to enter private zone setup mode, and the masking will turn into red. You can set the masking size and position in the private zone setup mode. In this mode, you can press “Shift” + “6” to increase masking horizontal size; “Shift” + “4” to decrease masking horizontal size; “Shift” + “2” to increase masking vertical size; “Shift” + “8” to decrease masking vertical size; Shift Joystick to select the position where the masking is located.
21. AUTO REGRESS： ：Auto regress to the shortest path during set a position. It can shorten the response delay, and increase the response performance and speed dome lifetime. ON: Enable the auto regress function. OFF: Disable the auto regress function. 22. MOTION: This is used to set a limitation for Auto Pan function. When Motion is ON, you can use Auto Pan function simply by pressing “Shift“+ “A.Pan “of the keyboard (according to A. Pan position you have set). OFF: Motion limitation function is disabled.
“Enter” to confirm. For Tour Run: Shift joystick to right and left for selecting RUN NUM (T01A~T16A) of the tour that you previously set. Press “Enter” to start running the tour. Alternatively, you could run the tour without entering MENU. Press “Position + 97” to run the tour that you have previously set, please be informed that this function is only valid for T01A. If you need to reset, press “IRIS –“ of the keyboard to exit. 24. X CNT： ： X-axis counter.
4. EPTZ3000/3000I FUNCTION SETUP AND OPERATION 4.1. Manual Control Mode Manual control: Shift Joystick Up/Down/Left/Right, and turn it Clockwise/Counterclockwise to control speed dome. Use the control keys which are Zoom, Focus and IRIS function keys on the keyboard to Zoom In/Out, focus N (near)/F (Far), or IRIS +/-. Note: Zoom In/Out control keys will be disabled when entering to OSD menu mode.
not tilt. 4.3. Position Setting Focus on a preset position: Press the number key, and then press Position to focus on the number of preset position; or you can press Position, then enter the preset position number, and then press Enter to focus on the number of preset position. Preset a position: Shift the Joystick to the position you would like to preset, and then press Shift + Position. The system will ask you to enter the preset position number (1~192), and then press Enter to save the position.
Dwell time: default is 2 sec; It can be changed by EVF Keyboard Set + A.Pan setting dwell time of A pos or B pos. 99 => Auto scan (360 degree) Default speed is 32. It can be changed by EVF Keyboard (Shift + A.Pan setting speed). We can even set camera’s ICR Day/Night function with RS-485 command via keyboard. How to do this? Press Position + 88 to link to Day mode or Position + 89 to link to Night mode, “ICR AUTO” message will be shown on the right-bottom part of the screen.
to enter the tour number you would like to run, and starts the tour after pressing Enter. To preset a tour before running is necessary. Preset a one-way tour: Press Set + Tour to preset a one-way tour. The system will ask you to enter preset position numbers (The positions need to be preset). After finish entering all positions, press Stop to quit, and then press Enter to save the tour. To-and-fro tour mode: Press Shift + Tour to run a to-and-fro tour.
AB two point pan if limit is ON. If you set the position number to 98, the dome will do a frame scan. Delete an alarm link: Press Clr + F1 to delete a link of alarm to position/tour. Note 1: After alarm output signal is terminated, the speed dome will resume action or return to its original position. Note 2: After powering on the speed dome, it will detect alarm status automatically. 4.6. Other Operations The EPTZ3000/EPTZ3000I can work with a DVR that has PTZ control functions, and a matching protocol.
APPENDIX : The Alarm I/O Connection There are 4 alarm inputs and 1 alarm output available. The alarm I/O connector that is marked as JP5 is a nine-pin connector. It is located on the PCB board of the housing. JP5 1 ~ 9 RELAY JP5 Video + Pin # Function 1 Alarm Input 3 2 Ground 3 Alarm Input 2 4 Alarm Input 1 5 Ground 6 Alarm Input 0 7 Normal Open (N.O.) 8 Common (COM) 9 Normal Close (N.C.
EverFocus Electronics Corp. Europe Office: Albert-Einstein-Strasse 1 D-46446 Emmerich, Germany Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886-2-26982334 TEL: 49-2822-9394-0 www.everfocus.de FAX: +886-2-26982380 www.everfocus.com.tw China Beijing Office: Room B-05D-1, KESHI PLAZA , Shangdi Information Industry Base, Haidian District, Beijing China 100085 TEL: +86-10-62973336/37/38/39 USA L.A. Office: 1801 Highland Ave. Unit A Duarte, CA 91010, U.S.A.
