EverFocus Operation Instruction IR Day/Night plus Wide Dynamic Range IP66 Bullet Camera EZ650
EVERFOCUS ELECTRONICS CORPORATION P/N: 4605XZ0650001AR Operation Instruction 2008 EverFocus Electronics Corp Please read this manual first for correct installation and operation. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. All rights reserved.
Precautions 1. Do not place any object on top of the cover. 2. Be careful when handling the camera, do not drop it or subject it to strong shock or vibration to prevent any damages to it. Do not disassemble it or place it on an unstable base. 3. Install the camera away from TV, radio transmitter, magnet, electric motor, transformer, audio speakers because the magnetic fields generate from above devices will distort the video image. 4.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents 1.1 FEATURES.......................................................................................................................................... 6 1.2 ACCESSORY PARTS LIST .............................................................................................................. 7 1.3 SPECIFICATIONS ............................................................................................................................. 8 1.4 DIMENSIONS .........................................
Chapter 1 1. Product Overview Achieve long range surveillance with clarity in virtually any lighting conditions. The amazing low light sensitivity of 0.05 lux before the added benefits of advanced DSP technology, delivered by a 1/3” Sony Super HAD CCD II sensor, is just the beginning with the new EverFocus EZ650. A 6-50mm varifocal auto-iris lens combined with high output IR illuminators delivers a useful range of over 80m/261ft.
Motion detection for 4 configurable zones. Privacy mask function for 8 configurable zones. Provides digital zoom up to 32x. Cables routed through weatherproof bushing in the bracket to prevent vandalism or other damage. IP66 weather resistant. Operating temperature range -40°C to 50°C/ -40°F to 122°F, with thermostatically controlled heater Vandal resistant. 1.2 Accessory Parts List Please be careful when you unpack the box due to the electronics devices inside.
1.3 Specifications Product Model Pickup Device EZ650 1/3” SONY Super HAD CCD Ⅱ Video Format NTSC or PAL Picture Elements 768 x 494 (NTSC)/752 x 582 (PAL) Horizontal Resolution Sensitivity S/N Ratio Electronic Shutter 560 TV Lines 0.05Lux/F=1.2(AGC ON); 0.0002Lux/F=1.2 (IR off ,Sens-up 256x Max; ~8X recommened) 0 Lux (IR On) Over 52dB (AGC off) 256x, 128x, ….1/50 (1/60) ~1/100,000 Video Output BNC 1.
1.4 Dimensions Drilling Dimension of holes to holes 45mm/1.8” 80mm/3.2” Dimension of Bracket 220.5mm/8.68” 84mm/3.31” 106.5mm/4.19 112.7mm/4.44 199mm/7.
Dimension of whole camera with bracket 275mm/10.8” 107.5mm/4.3” 243.5mm/9.
1.
1.6 Back Panel Layout 24VAC model (for 24VAC Power Only) 2 110V~240VAC model (for 110V ~240V Power only) 2 1 1 3 4 3 5 5 6 6 7 7 1. Video Output Connector Connect the video output of the camera to a color monitor or other video devices through a 75 Ohm type coaxial cable with BNC female connector at backside of the camera. 2. Power Input Terminal Connect the appropriate power to each model. N/L is used to connect to power in. PE is a ground pin. 3.
5. Control key selection switch Switch to OSD to control OSD menu by using the control key or switch to LENS to adjust zooming and focus (please see “2.3.1 Lens setting” and “3. OSD Menu & Configuration” for details). Note: when it is connected to RS485 for keyboard control, please switch to OSD, otherwise it cannot be controlled remotely. 6. Control key For setting Lens & OSD menu. 7. Cable clips Used to fix power cable and RS485 cable. 1.
Chapter 2 2. Installation This chapter will describe, in general terms, how to install the EZ650 camera. STEPS: 1. Wire and mount the camera. See 2.1 2. Adjust the camera position. See 2.2 3. Adjust Lens. See 2.3 4. Connect to Keyboard (Optional) See 2.4 Warning To prevent electrical shock, turn off the electrical power before making electrical connections. Do not expose the appliance to water or moisture, nor try to operate it in wet areas. 2.1 Wiring and Mounting 1.
2. Fix the bracket to wall by using 4 screws. Coaxial cable Power cable RS485 cable 3. Open camera’s back cover: Loose the 2 screws from the back panel cover, then open the back cover.
4. Take off the cap of waterproof conduit which is at the camera bottom. Power cable (Φ10.3mm) Coaxial cable (Φ6mm) RS485 (Φ5mm) Note: 1. the holes of waterproof conduit were plugged, please remove the plug when you need to use it for connection. 5. Take coaxial cable, power cable and RS485 cable to pass through waterproof conduit, place them into camera housing.
Coaxial cable Power cable RS485 cable Note: 1. Power cable’s diameter must be less than 10 mm 2. Only use RG59/5C2V for Video cable 3. RS485 cable must be less then 5 mm 6. Close the waterproof cap and fix waterproof conduit to the base of camera firmly. 7. Fix the camera body to bracket by using the 4 shorter screws.
8. Connect RG59 coaxial cable with BNC connector. 9. Unscrew both cable clips, wire power cable and RS485 cable through the cable clips. Then, screw the cable clips to rear panel. a. Connecting Power-24VAC model: connect 24VAC power on N and L 100VAC~240VAC Model: Connect PE, N and L. *Warning* To prevent electrical shock, turn off the electrical power before making electrical connections. Do not connect high voltage power to the camera. It may damage the camera.
Screws for back panel 2.2 Adjusting Camera Position Adjust camera’s angle vertically or horizontally by using hex key included in package.
2.3 Adjusting Lens Open camera’s base, a control key is attached at inner side of the base. Detach the control key and use this key for OSD or Lens setting. UP 2.3.1 Lens Setting Please turn the control key selection switch at the back panel to “Lens”.( key to do lens setting. ). Use the control UP Mini-Joystick The Cursors & the mini-joystick Turn the mini-joystick Up () or Down () to adjust zoom in / zoom out, Turn the mini-joystick Left () or Right () to adjust focus.
2.4 Keyboard Connection (Optional) Please refer to Chapter 4 for more details of Keyboard control. 1. 2. 3. 4. 5. Connect the cable from keyboard’s RS485 port to camera’s RS485 port. (Keyboard is an optional accessory). RS485 connecting accessories are included in Everfocus Keyboard package. Connect the cable from video output jack of the camera to monitor’s input jack. EZ650 recognizes EVF-1, EVF-2 and Pelco-D protocols automatically. (No setting is required) The camera default RS485_ID is 01.
Chapter 3 3. OSD Menu & Configuration This chapter introduces how to configure the camera OSD menu. 3.1 Control Key General Operation Guide Please turn the control key selection switch at the back panel to “OSD” ”( Use the control key to do OSD menu setting. ). UP Mini-Joystick The Cursors & the mini-joystick I. Bring Up the General OSD Menu Simply press the mini-joystick to bring up the general OSD menu. II.
When the item with sub-menu is selected, press the mini-joystick to switch to the sub-menu for further settings. Please refer to the diagram below. SETUP LENS > LENS DC <┘ SHUTTER ___ WHITE BAL. ATW BACKLIGHT OFF AGC MIDDLE DNR LOW Main Menu SENS-UP AUTO <┘ SPECIAL <┘ EXIT NOTE: For those selected items with “ LEVEL |+++++++++| 25 Sub-Menu s Menu ” sign in the end, they have the sub-menu for further settings. VI. Return to Previous Page Press the mini-joystick to return to previous page. VII.
3.2 RS485 ID & Baud Rate Setting Note: This section is optional preserved for the people that want to change camera ID and baud rate. In most situations, we suggest you can just use Camera ID-01 and Baud Rate-9600, Protocol-Pelco D on keyboard, then it would work. I. Please turn the control key selection switch at back panel to “OSD”( ). II. Press the mini-joystick for 4 seconds until you see the following menu.
A N a n ─ F I B O b o · C P c p D Q d q 0 E R e r 1 F S f s 2 G T g t 3 H U h u 4 I V i v 5 J W j w 6 K X k x 7 L Y l y 8 M Z m z 9 C L R P O S E N D R M W A R E _+ V E R _ _ _ b. RS485_ID- adjustable 01~128. Default value is 01. Move joystick RIGHT and LEFT to adjust it. RS485 ID of EZ650 has to be the same as Keyboard’s CAM ID.
d. DATA STORED- Confirm with you that the last 3 settings you have made will be saved. A N a n ─ B O b o · C P c p D Q d q 0 E R e r 1 F S f s 2 G T g t 3 H U h u 4 I V i v 5 J W j w 6 K X k x 7 L Y l y 8 M Z m z 9 C L R P O S E N D D A T A _ S T O R E D _ _ _ _ e. ENTER_SET_MENU- press the mini-joystick to enter OSD menu setting.
3.3 OSD Menu Setup 3.3.1 OSD Menu Tree Default settings are shown bold or in brackets.
— Motion — Privacy — Sync. — Language — Off — On — Off — On — INT / LL — English Trad. Chinese Simp.
3.3.2 LENS When the SETUP menu is displayed on the screen, please direct the arrow to point to “LENS” by using the UP and DOWN buttons. The iris opening can be adjusted in DC mode in LENS LEVEL. The level can be adjusted from 0 to 50. Please select RETURN and press the SETUP button if you would like to return to the previous menu. 3.3.3 EXPOSURE 3.3.3.1 SHUTTER 1. 2. 3.
NOTE: 1. SENS-UP will be disabled, if AGC is OFF or the default SHUTTER value (1/50 PAL / 1/60 NTSC) was changed 2. The image becomes brighter when the setting increases; however, the after image increases as well. Due to the increased light sensitivity of the Super HAD II chip, far less DSP ‘boost’ is needed, resulting in color or B/W images in low light with minimal ghosting. 3. Please note that spots and noise may appear if light amplification increases when SENSE-UP is operating.
1. Please direct the arrow to point to “BLC” by using the UP and DOWN buttons. 2. Select the HSBLC mode by pressing the LEFT or RIGHT button. Then make adjustments as below: LEVEL Adjust the sensitivity level for HSBLC from 0 to 8. DEFAULT Set the factory default values for HSBLC. LEFT/RIGHT Set the Left/Right side of an area for the HSBLC to be adjusted. The value adjustable is 0~6. WIDTH Set the width of an area for the HSBLC to be adjusted. The value adjustable is 0~6.
3.3.4 WHITE BALANCE CONTROL The screen color can be adjusted by using the WHITE BALANCE function. Please direct the arrow to point to “WHITE BAL” by using the UP and DOWN buttons. Please select the mode you would like to operate by pressing the LEFT or RIGHT button. Please select one of the 6 modes below: ATW Auto Tracking White Balance: This mode can be used within the color temperature range from 5,500°K to 6,000°K (eg, fluorescent light, outdoor, sodium vapor lamp or inside tunnels).
Press “RET” to save all settings in the DAY/NIGHT menu and returns to the previous menu. Press “END” to save all the setting menus and exit. COLOR AUTO Delay S-Level E-Level EXT The picture is always displayed in color, even at low light levels. NOTE: In “color” operation, there is an IR “cut” (blocking) filter between the lens and the sensor; thus EZ650 camera has very little IR sensitivity when the image is displayed in color.
Please direct the arrow to point to “CAM TITLE” by using the UP or DOWN button. Select “ON” by pressing the LEFT or RIGHT button. Press SETUP button. Maximum 15 characters can be used for the ID. Use UP, DOWN, LEFT and RIGHT buttons to move the cursor to the letter to be chosen. Use SETUP button to choose that letter. Once a name has been selected, please choose the position on the screen where you would like to display the name. Move the cursor onto “POS” and press the SETUP button.
3.3.7.5 D-ZOOM Setup for digital zoom. OFF ON Disable the D-ZOOM function D-Zoom: Select digital zoom from X1.0 up to X32. Note that zoom levels above X4 may lead to excessive pixellation. Setup of the position of the magnified image in view (0 is the center of the image): Pan: Select digital pan from -100 to 100. Tilt: Select digital tilt from -100 to 100. Press “RET” to saves all settings in D-ZOOM menu and returns to the previous menu. Press “END” to save all the setting menus and exit. 3.3.7.
MOTION VIEW RETURN the sensitivity value is high, motion detection sensitivity increases to sense very small movements and vice versa. Select “ON” to display motion detection pixels in the live view. Press “RET” to save all settings in MOTION menu and return to the previous menu. Press “END” to save all the menu settings and exit. 3.3.7.10 PRIVACY This mode masks areas you do not want to display on the screen or record.
3.3.8.1 SHARPNESS The contour of the video image becomes cleaner and more easily distinguished as the level of SHARPNESS increases. If the level is set too high, it may affect the video image and cause noise. The available range of level is 0~31. 3.3.8.2 BLUE Adjust image’s blue level. The available range of level is 0~100. 3.3.8.3 RED Adjust image’s red level. The available range of level is 0~100. Press “RET” to saves all settings in the ADJUST menu and returns to the previous menu.
Chapter 4 Control from Keyboard EKB500 (Optional) Note! Before being able to control keyboard, make sure Keyboard RS485 camera ID, Baud rate match the camera. (see COM port setting in EKB500 manual). EZ650 camera ID default is 01. Baud rate is 9600. Support Protocol EVF-1, EVF-2 and Pelco-D. 4.1 Key Features with Keyboard 1. OSD can be set up from Keyboard. 2. Lens Zoom and Focus can be controlled by keyboard. 4.2 OSD Menu Setting by Keyboard a. Press “Menu” to enter SETUP menu. b.
d. Move the joystick RIGHT () and LEFT () to adjust the mode and parameters of the selected item. e. Press “Menu” to leave and goes to previous menu after setting. Move to “exit” and press “menu” button when you finish all settings. f. For detail setting and every setup function, Please refer to “3.3. OSD Menu Setup”. 4.3 Lens Adjustment by Keyboard 1. Press Zoom in or Zoom out to adjust zoom or Turn Joystick clockwise to zoom out. Counterclockwise to zoom in. 2.
EverFocus Electronics Corp. EverFocus Taiwan: 12F, No.79, Sec. 1, Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886 2 2698 2334 FAX: +886 2 2698 2380 www.everfocus.com.tw marketing@everfocus.com.tw EverFocus Europe - Germany: Albert-Einstein-Strasse 1, D-46446 Emmerich, Germany TEL: +49 2822 93940 FAX: +49 2822 939495 www.everfocus.de info@everfocus.