Speed Dome EPTZ3100/EPTZ3100I USER MANUAL Date: Jan.
Table of Contents 1. EPTZ3100/EPTZ3100I OVERVIEW........................................................5 1.1. Introduction ................................................................................................5 1.2. Specifications .............................................................................................7 1.3. Feature ........................................................................................................9 1.4. 1.3.1. Profile of EPTZ3100/EPTZ3100I.......
. EPTZ3100/EPTZ3100I CAMERA SETUP MENU .................................38 3.1. Structure of the Setup Menu ...................................................................38 3.2. VIDEO SETTINGS .....................................................................................39 3.2.1. EXPOSURE ........................................................................................39 3.2.2. FOCUS MODE ....................................................................................41 3.2.3.
3.5.8. 3.6. EXIT ....................................................................................................60 ALARM ......................................................................................................60 3.6.1. ALARM INPUTS..................................................................................60 3.6.2. ALARM OUTPUTS..............................................................................63 3.6.3. MOTION DETECT.................................................
1. EPTZ3100/EPTZ3100I OVERVIEW 1.1. Introduction EPTZ3100 series has 2 types, EPTZ3100 is outdoor type whereas EPTZ3100I is indoor type, using high sensitivity and high resolution CCD to display high quality image. The design of ICR (IR cut filter removable) can provide real color even under strong sunlight in day time. Under slight light in night time, a clear image can still be displayed. WDR design allows the camera to be installed in any environment. Fast moving function can reach to 360°/1sec.
192 preset positions are available. 16 cruise tours can be set, and each tour contains up to 16 positions. Up to 256 speed domes can be supported on a RS-485 bus when all speed domes are controlled by keyboard EKB500. Built-in fan to enhance heat dissipation at high temperature and circulate heat to keep system operation at low temperature. Built-in 4 alarm inputs and 2 alarm outputs.
1.2. Specifications Product Model EPTZ3100 (outdoor) EPTZ3100I (indoor) Pickup Device 1/4” CCD Video Format NTSC or PAL Scanning System NTSC: 525 TV lines, 60 fields/sec PAL: 625 TV lines, 50 fields/sec. Picture Elements 768 x 494 (NTSC) 752 x 582 (PAL) Horizontal Resolution 520 TV Lines Sensitivity 0.4 Lux/ F1.6 (ICR OFF) 0.08 Lux/ F1.
Horizontal Rotation Speed 0.01°/s －360°/s (1-255 grade shift gears) Horizontal Rotation Range 360° unlimited rotation Tilt Rotation Range 180° pendulum motion Auto Zoom Speed Control Control speed auto-adjusted according to zoom length changing Auto Pan, 2 points Can set freely scanning Auto Pan Speed 1－255 grade available Dwell Time (2 points) 1－99 second available Preset Positions Running to position speed 192 positions 1－255 grade available,0.
1.3. Feature 1.3.1.
1.3.2. EPTZ3100/EPTZ3100I Base Board The base board that is inside the top housing connects to power cable, video cable, control cable, alarm cable and fan. In order to connect to cables, the board needs to be taken off, and put back after finishing connecting to all cables. The connectors of cable names are marked on the board in white text. The details of the alarm connector are shown on the APPENDIX. There are 4 alarm inputs and 2 alarm outputs available, represented by Pin 1~12.
Pin # Function 1 ALM_NO_B (Alarm Output Normal Open B) 2 ALM_COM_B (Alarm Output Common B) 3 ALM_NC_B (Alarm Output Normal Close B) 4 ALM_NO_A (Alarm Output Normal Open A) 5 ALM_COM_A (Alarm Output Common A) 6 ALM_NC_A (Alarm Output Normal Close A) 7 ALMIN1 (Alarm Input 1) 8 GND (Ground) 9 ALMIN2 (Alarm Input 2) 10 ALMIN3 (Alarm Input 3) 11 GND (Ground) 12 ALMIN4 (Alarm Input 4) 13 VIDEO+ 14 VIDEO- 15 RS485- 16 RS485+ 17 AC24A+ 18 AC24B- 11
1.4. EPTZ3100/EPTZ3100I Quick Operation Guide (Work with EKB500) EPTZ3100/EPTZ3100I and EKB500 (Keyboard) can work together by using factory default setting. You just need to connect cables by the following steps: 1. Connect the RS-485 cable to EPTZ3100/EPTZ3100I and a keyboard (EKB500). 2. Connect a video cable from EPTZ3100/EPTZ3100I to a monitor. 3. Connect the power to the EPTZ3100/EPTZ3100I and a keyboard (EKB500).
2. EPTZ3100/EPTZ3100I INSTALLATION 2.1. Packing List There are 3 boxes that are camera main body with a camera module, top housing with a base board & pin connector and outer housing with bubble, plus one tool packet in the package.
* EKB500 (Keyboard) * EKB200 (USB Controller Keyboard) 14
2.2. Cable Needed Yellow RS485+ Orange RS485VIDEO 24VAC Power Cable An adapter with 24VAC/3.5A output provides the power to the EPTZ3100/EPTZ3100I. An extension power line may be needed. Note: The input AC voltage range of an adapter depends on different area. Please make sure the voltage range before installing. Video Cable A BNC cable is used for connecting an EPTZ3100/EPTZ3100I to a DVR or a monitor. An amplifier may be needed if the video cable is too long.
terminal resistance settings. All of the settings should be confirmed before the dome is installed. The control-related setting that is address, communication protocol and transmission speed have to be set consistently with the control device such as a keyboard or a DVR. Notice: Please make sure the power is off before setting, and restart the EPTZ3100/EPTZ3100I to enable a new value after changing. 2.3.1.
ON ON 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Protocol/Baud rate ID address Note: You will see the label of Protocol & Baud Rate as well as RS-485 ID address show on the speed dome. White part represents the switch key. For example: for EVF protocol, white keys are all switched downward; for ID Address 0, white keys are all switched downward.
Switch ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1
Switch 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 ON 1
2.3.2. Communication Protocol Setting The 1st, 2nd and 3rd bits are used to set communication protocol. The factory default protocol is EVF. Notice: Please make sure the power is off before setting, and restart the EPTZ3100/EPTZ3100I to enable a new value after changing. Set all of protocol switches to ON; the speed dome EPTZ3100/EPTZ3100I will enter a self-test mode. 2.3.3. Transmission Speed Setting (Baud Rate Setting) The 4th and 5th bits on the PCB board are used to set the Baud Rate.
2.4. Bracket and Speed Dome Installation 2.4.1. Installation Requirements 1. Installation should be handled by a qualified service agent and should comply with all local regulations. Service personnel should expect potential problems such as surface strength, surface material, falling objects, outer breaches, building vibration or other similar conditions. 2. Check for all necessary materials, and ensure if the selected installation location is suitable for the EPTZ3100/EPTZ3100I.
2.4.2. EPTZ3100 Dome Camera Wall Mount Simple Installation 1. Screw the top housing to bracket by using a hexagon wrench. 2. Put the waterproof silicon pad on top of the bracket base for waterproof purpose.
3. Connect the cable you detached from base board to the RS485 cable, Power cable and video cable you thread from the wall or ceiling. RS485 cable has to be connected via a terminal block. If you need to connect alarm cable, thread the alarm cable through the second hole. Note: Since video cable and power cable are bare wires, installers have to prepare their own BNC connector and power cord connector. RS485 cable Video cable Power cable Alarm cable 4. Screw in 4 screws for mounting the bracket base.
5. Screw in 4 long screws to fix the bracket to bracket base.
2.4.3. EPTZ3100 Dome Camera Wall Mount Installation Note: Installation location that is a wall, a pole or a ceiling needs to support above five times the total weight of the camera assembly (about 16 kg) to avoid shaken images, and dropping. 1. Pull the hole of the base board to open it. Detach the power and RS485 wires first by using a screw driver.
2. Apply the adhesive stripe at back of desiccant pack to the inner side of the top housing. There are totally 3 desiccant packs to be applied. 3. When all the desiccant packs are pasted and alarm cables are connected properly, put the base board back to its original place, you will need to pull open the switch in order to have the base board fitted to the top housing. Pull open this switch Note: To close the base board, please push the base board twice consequently to lock it up.
4. Put the waterproof silicon pad on top of the base board for waterproof purpose. Waterproof silicon pad Base board 5. Connect the cable you detached from base board to the RS485 cable, Power cable and video cable you thread from the wall or ceiling. RS485 cable has to be connected via a terminal block. If you need to connect alarm cable, thread the alarm cable through the second hole.
6. Screw in 4 screws for mounting the bracket base. 7. Thread the cable through the bracket.
8. Screw the top housing to bracket by using a hexagon wrench. 9. Screw in 4 long screws to fix the bracket to bracket base.
10. Pull the hole of base board to open it again. Connect the power and RS485 wires back to power pin and RS485 pin. If you need to connect alarm, connect alarm cable to alarm pin. 11. Hold and push the main body toward the bracket until it is firmly fixed to the bracket. To release it, press orange buttons at both sides of the body.
Note 1: When you push the orange buttons to detach the main body from bracket, please hold the main body carefully, otherwise it may fall down. Note 2: Aim the Arrow label of the main body to the same Arrow label of the bracket when you need to push the main body toward bracket. 12. Twist the cover of main body to top housing clockwise until it is firmly fixed to top housing.
Note 1: In order to protect the bubble from dirt and scrape, please put on the gloves before installing the bubble. Note 2: The camera module on the mechanical part is very sensitive. Please be careful when installing this part. 13. Turn on the power, and start to operate the EPTZ3100. Note: When turning on the power, EPTZ3100 will enter self-inspection mode, and carry out a self-testing program. After finishing self-inspection, you can start to operate the EPTZ3100. 2.4.4.
2. Screw the 3 screws of EPTZ top housing to the 3 holes of indoor recessed mount bracket. 3. Put the indoor recessed mount bracket to the hole that you just made on ceiling. 4. Use a screwdriver to turn the rotation clips (x 3) until they firmly fix to the ceiling.
5. Snap main body to the indoor recessed mount bracket. NOTE: Aim the Arrow label of the main body to the same Arrow label of the bracket when you need to push the main body toward bracket. 6. Turn the housing of speed dome until it fixes to the top housing.
7. Aim bracket’s fillister to surface ring’s fillister, turn it until it is firmly fixed.
2.5. Bracket and Adapter 2.5.1. Indoor Ceiling Pendent Mount Bracket The indoor ceiling pendent mount bracket is used for installing a speed dome on the ceiling. 2.5.2. Pole Mount Adapter The pole adapter is used for installing a wall mount bracket to a pole indoors or outdoors.
2.5.3. Corner Mount Adapter The corner mount is used for installing a wall mount bracket to a 270° corner of walls indoors or outdoors. 2.5.4. Indoor Concrete Ceiling Mount Adapter Indoor Concrete Ceiling Mount Adapter is used for indoor installation to concrete ceiling.
3. EPTZ3100/EPTZ3100I CAMERA SETUP MENU In this section, setup and operation guide of EPTZ3100/EPTZ3100I will be introduced. There are 9 items of the setting menu. 3.1. Structure of the Setup Menu Press MENU to enter camera setup menu. Turn the Joystick up/down to change subentries, and right/left to change the setting. If there is an arrow at the end of selection, it means that selection has a sub-menu, please press Enter key of keyboard to enter sub-menu.
3.2. VIDEO SETTINGS In main menu, turn joystick Up / Down to select VIDEO SETTINGS. Turn joystick Left / Right to enter VIDEO SETTINGS sub-menu (see diagram 3.2). VIDEO SETTINGS EXPOSURE<┘ POSITIONS FOCUS MODE ONE PUSH OSD/AREAS DIGITAL ZOOM OFF AUTO MODES WHITE BALANCE OUTDOOR ALARM DAY/NIGHT AUTO PRIVATE ZONES DIG. NOISE REDUCE MIDDLE SYSTEM WIDE DYNAMIC RANGE OFF INFO EXIT EXIT (diagram 3.
EL.SHUTTER: Select electronic shutter mode from the options of the menu. There are AUTO, A.FLK , 1/50, 1/160 , 1/250 , 1/1000 , 1/2500, 1/10000, 1/120,000, X2, X4, X6 and X8. AUTO: The AUTO electronic shutter mode is enabled. The shutter speed is controlled automatically according to the brightness of the screen A.FLK: Anti-Flicker. Camera will auto adjust the shutter to reduce the flicker caused by fluorescent light. 1/60 (NTSC) and 1/50 (PAL): default auto shutter.
sec for PAL. AUTO X8, AUTO X12, AUTO X16, AUTO X32, AUTO X64, and AUTO X128 work the same as AUTO X4 with different times of shutter speeds. NOTE: If EL. SHUTTER is selected, SLOW SHUTTER will be disabled. IRIS MODE: AUTO mode or MANUAL mode can be selected. MANUAL: The brightness of the image can be adjusted. AUTO: The brightness of the image signal can be adjusted automatically depending on the amount of light.
MANUAL: Enable the manual focus mode. 3.2.3. DIGITAL ZOOM Magnification of the digital zoom can be selected among OFF, 2X, 4X and 8X. OFF: Disable the digital zoom function. 3.2.4. WHITE BALANCE The white balance function corrects the abnormal white color into the normal white color under any color temperature lighting. White Balance has the following modes: OUTDOOR: This mode is an automatic mode. It is recommended to use this mode in an area under a broad color temperature.
increased sensitivity in low light environments. Select from AUTO, DAY and NIGHT NIGHT: IR cut filter is always removed (ICR ON). DAY: IR cut filter is always attached (ICR OFF). AUTO: Auto Day/Night mode switch. The camera will automatically switch the settings needed for attaching or removing the IR cut filter. With a set level of darkness, the IR cut filter is automatically disabled (ICR ON), and the infrared sensitivity is increased.
Notice: When the wide dynamic range is ON, some part of the image may appear solarized. This is normal for the wide dynamic range, and is not a camera malfunction. 3.2.8. EXIT Select Exit to save settings and exit from current page.
3.3. POSITIONS In main menu, turn joystick Up or Down to select POSITION option. Press Enter key or turn joystick Left / Right to enter POSITION sub-menu (see diagram 3.4). VIDEO SETTINGS POSITIONS OSD/AREAS SET POSITIONS <┘ AUTO MODES FREEZE PICTURE ALARM EXIT OFF PRIVATE ZONES SYSTEM INFO EXIT (diagram 3.4) Press Enter key of keyboard to enter SET POSITIONS sub-menu. Turn the joystick Left / Right to select preset position. There are totally 36 preset positions can be set in one page.
PRESET NO. 1 POSITION SET <┘ SPEED 100 DWELL TIME (S) 4 FOCUS MODE MANUAL WHITE BALANCE AUTO TITLE 1 DEFAULT ON MOVE TO POSITION IRIS+: SAVE AND RETURN RETURN (diagram 3.6) POSITION: Select from SET and CLEAR. SET: Select SET and press Enter key of keyboard, you will be entered to a sub-menu. Turn the joystick to your desired position. Once the position is confirmed, press IRIS+ key of keyboard to save setting and return to previous menu.
SPEED: Select the speed for the preset position. The value is from 1 to 255 and 255 is the highest speed. DWELL TIME (S): Select the dwell time (in second) for the preset position from 1 to 99. FOCUS MODE: Select focus mode for the preset position from MANUAL, ONE PUSH and AUTO. WHITE BALANCE: Select the white balance for the preset position from Auto, Indoor and outdoor. TITLE: Enter title name for the preset position. Turn the joystick Up or Down to select the character.
3.4. OSD/AREAS In main menu, turn joystick Up or Down to select OSD/AREAS. Turn joystick Left or Right to enter OSD/AREAS sub-menu (see diagram 3.8) VIDEO SETTINGS POSITIONS CAM. TITLE EPTZ3100__ OSD/AREAS AREAS <┘ AUTO MODES DIRECTIONS <┘ ALARM DISPLAY <┘ PRIVATE ZONES EXIT SYSTEM INFO EXIT (diagram 3.8) 3.4.1. CAM. TITLE Enter title name for the camera. Turn the joystick Up or Down to select the character. Maximum 10 digits of character can be inputted.
In zone menu, you can set a zone and name it, when the speed dome turns to the zone you set, it will display zone name on the screen (only if “OSD/AREAS->Display -> Zone” is set as “YES”). Turn the joystick to Up/Down to select the character. Turn the joystick Left or Right to select the character position. Once the title is inputted, turn the joystick Left/Right to go “Range” section, and press Enter key to enter Range sub-menu. Use the joystick to move speed dome to its left position.
Turn joystick Right/Left to highlight the zone you have set and turn the joystick Up/Down to select another zone number. If you wish to clear the zone you have set, go to “CLR” and press Enter key. 3.4.3. DIRECTIONS Press Enter key of keyboard or turn joystick Left/Right to enter DIRECTIONS sub-menu (see diagram 3.12) DIRECTIONS NORTH CAM. TITLE SET NORTH<┘ EPTZ3100__ DEFAULT NORTH AREAS <┘ [PUSH ENT] DIRECTIONS <┘ DISPLAY <┘ RETURN EXIT (diagram 3.
3. Press IRIS+ key of keyboard to save and return. DIRECTIONS NORTH SET NORTH <┘ DEFAULT NORTH [PUSH ENT] RETURN (diagram 3.14) 4. Go to “DEFAULT NORTH” and press Enter key to set the north position as default north position. 5. Go to Return and turn joystick Left/Right to return to previous menu.
3.4.4. DISPLAY Press Enter key of keyboard or turn joystick Left/Right to enter DISPLAY sub-menu (see diagram 3.15) SHOW OSD ON CAMERA TITLE NO DIRECTIONS NO AREAS <┘ ZONES NO DIRECTIONS <┘ PRESET TITLE YES DISPLAY <┘ ZOOM NO EXIT FAN NO MOTION NO CAMERA STATUS NO CAM. TITLE EPTZ3100__ RETURN (diagram 3.15) 1. SHOW OSD: ON: show OSD of Camera Title, Directions, Zones, Preset Title, Motion, Zoom, Fan and Camera Status. OFF: do not show OSD. 2 SEC: show OSD for 2 seconds.
4. ZONES YES: show zones NO: do not show zones 5. PRESET TITLE YES: show preset title NO: do not show preset title 6. ZOOM YES: show zoom multiple when zoom in or zoom out. NO: do not show zoom multiple. 7. FAN YES: show fan indication when fan is enabled. NO: do not show fan indication. 8. MOTION YES: show motion message when a motion occurs. NO: do not show motion message when a motion occurs. 9. CAMERA STATUS YES: shows camera status NO: do not show camera status 10.
3.4.5. EXIT Select Exit to save settings and exit from current page. 3.5. AUTO MODES In main menu, turn joystick Up/Down to select AUTO MODES. Turn joystick Left/Right to enter AUTO MODES sub-menu (See diagram 3.16) VIDEO SETTINGS AUTOPAN <┘ POSITIONS PRESET TOURS <┘ OSD/AREAS PATTERN <┘ AUTO MODES AUTO RESUME OFF ALARM RESUME TO POS.1(H) PRIVATE ZONES POWER UP FUNC PREV MODE SYSTEM AUTO FLIP ON INFO EXIT EXIT (diagram 3.16) 3.5.1.
a. ENDLESS MODE ON: enable endless mode. The speed dome will perform 360 degree endless auto-pan. OFF: disable endless mode. The speed dome will perform auto-pan between position left and position right. b. SPEED Select speed from 1~255 and 255 is the highest speed. c. DWELL TIME L (S) Select dwell time of the left position from 1~99 seconds. d. DWELL TIME R (S) Select dwell time of the right position from 1~99 seconds e. SET LEFT POS.
AUTOPAN ENDLESS MODE ON SPEED 32 DWELL TIME L (S) 4 DWELL TIME R (S) 4 MOVE TO POSITION SET LEFT POS. <┘ IRIS+: SAVE AND RETURN SET RIGHT POS. <┘ DEFAULT ON IRIS-: RETURN (diagram 3.18) f. SET RIGHT POS. Press Enter key or turn the joystick Left/Right to enter SET RIGHT POS. menu. Turn the joystick to the position where you wish to set RIGHT position. Press IRIS+ key of keyboard to save setting and return to previous menu. (see diagram 3.
g. DEFAULT ON: all settings in AUTOPAN menu will be returned to default values. OFF: the setting in AUTOPAN menu is not default value. h. RETURN Turn joystick Left/Right to return to previous menu 3.5.2. PRESET TOURS Press Enter key or turn the joystick Left/Right to enter PRESET TOURS sub-menu (see diagram 3.20) TOUR NO. 1 AUTOPAN <┘ PRESET TOURS <┘ PATTERN <┘ AUTO RESUME OFF RESUME TO POS.
setting of preset position. e. PREV PAGE/NEXT PAGE: Turn the joystick Left to go previous page or turn joystick Right to go next page. f. RETURN: Turn joystick Left/Right to return to previous menu. 3.5.3. PATTERN Press Enter key of keyboard to enter PATTERN sub-menu (see diagram 3.21) AUTOPAN <┘ PATTERN SETUP PRESET TOURS <┘ PATTERN DURATION ACTION PATTERN <┘ AUTO RESUME OFF PAT1 --- PLAY<┘ RESUME TO POS.
d. Turn the joystick to record the tour you wish to set. Press IRIS+ when you finish setting pattern tour. Press IRIS- if you wish to cancel this action. At duration column of PATTERN SETUP menu, you will see the duration time of pattern you set. e. When you return to PATTERN SETUP menu, turn the joystick Left/Right to PLAY. Press Enter key of keyboard. The camera starts to run the pattern tour you set.
MODE, POS.1 (H), TOUR1, PAT.1 and AUTOPAN. 3.5.6. POWER UP FUNC Turn the joystick Left or Right to select the mode to return to when power failure occurs. It is selectable from PREV MODE, POS.1 (H), TOUR1, PAT.1, AUTOPAN and OFF 3.5.7. AUTO FLIP Select ON to enable Auto Flip function or select OFF to disable Auto Flip. 3.5.8. EXIT Exit from the current menu. 3.6. ALARM In main menu, turn joystick Up or Down to select ALARM. Turn joystick Left or Right to enter ALARM sub-menu (see diagram 3.
a. Go to INPUT NO. selection and turn the joystick Left/Right to select alarm input number from 1 ~4. b. Type: Select Normal Close (NC), Normal Open (NO), NIGHT NC, NIGHT NO, or OFF for alarm type. NC: Enable a normal close alarm input. NO: Enable a normal open alarm input. NIGHT NC: Set camera at night mode with normal close alarm input. When there is event triggered, the camera will be changed to day mode. NIGHT NO: Set camera at night mode with normal open alarm input.
PATTERN: When the alarm is triggered, speed dome will run the pattern. Turn the joystick Left/Right to select on Pattern and press Enter key to select pattern number. Turn joystick Left/Right to make selection. It is selectable from1~4. Press Enter key again to confirm selection. TOUR: When the alarm is triggered, speed dome will run the tour. Turn the joystick Left or Right to select on Tour and press Enter key to select tour number. Turn joystick Left or Right to make selection. It is selectable from1~16.
3.6.2. ALARM OUTPUTS Press Enter key of keyboard to enter ALARM OUTPUTS sub-menu. (see diagram 3.26) ALARM OUTPUT TRIGGER ALARM INPUTS<┘ ALARM OUTPUTS <┘ OUTPUT NO 1 INPUT1 YES INPUT2 YES INPUT3 YES INPUT4 YES MOTION NO MOTION DETECT <┘ EXIT SYSTEM ERROR NO REMOTE NO RETURN (diagram 3.26) a. OUTPUT NUM: Select Output number from 1~2. b. INPUT1: Select YES to enable Alarm input 1 for the alarm output selected. Select NO to disable Alarm input 1. c.
Select NO to disable this function. i. RETURN: RETURN to the previous menu. 3.6.3. MOTION DETECT Press Enter key of keyboard to enter MOTION DETECT sub-menu. (see diagram 3.27) ALARM INPUTS <┘ MOTION DETECT 1 OFF ALARM OUTPUTS <┘ SENSITIVITY 50 MOTION DETECT <┘ EXIT EXIT (diagram 3.27) a. Turn the joystick Left or Right to select ON for motion detection. A window as below pops up. MOTION DETECT INFO M1: 67 M2: 87 (diagram 3.28) b.
3.7. PRIVATE ZONES In main menu, turn joystick Up/Down to select PRIVATE ZONES masking. Turn joystick Left/Right to enter PRIVATE ZONE sub-menu (see diagram 3.29) VIDEO SETTINGS PRIVATE ZONE 1 ON <┘ POSITIONS PRIVATE ZONE 1 OFF OSD/AREAS PRIVATE ZONE 1 OFF AUTO MODES PRIVATE ZONE 1 OFF ALARM PRIVATE ZONE 1 OFF PRIVATE ZONES PRIVATE ZONE 1 OFF SYSTEM PRIVATE ZONE 1 OFF INFO PRIVATE ZONE 1 OFF EXIT ZONE COLOR BLACK EXIT (diagram 3.29) a. ON: Turn joystick Left/Right to select ON/OFF.
c. Select the area to be covered first. Turn joystick Left/Right to adjust width of the private zone area. Turn joystick Up or Down to adjust height of the private zone area. Press IRIS- key to set private zone position. Press IRIS+ to save and return to previous menu.
3.8. SYSTEM In main menu, turn joystick Up/Down to select SYSTEM. Turn joystick Left/Right to enter SYSTEM sub-menu (see diagram 3.32) VIDEO SETTINGS AUTO INIT OFF POSITIONS LANGUAGE ENGLISH OSD/AREAS PASSWORD <┘ AUTO MODES LOAD DEFAULT [PUSH ENT] ALARM RESTART [PUSH ENT] PRIVATE ZONES EXIT SYSTEM INFO EXIT (diagram 3.32) a. AUTO INIT: Select auto initiation time from OFF, DAILY, WEEKLY.
PASSWORD ACTIVE: Select YES to activate password mode. Select NO to disable password mode. ENTER PASSWORD: Enter the password VERIFY PASSWORD: Enter the password again to confirm your input. Press IRIS+ key to save and return to previous menu. Press IRIS- key to cancel. SAVE AND RETURN: Turn joystick Left/Right to save the changes and return to previous menu. RETURN: Turn joystick Left/Right to return to previous menu without saving changes. d.
c. BAUDRATE: shows baud rate of this speed dome d. RS-485-ID: shows RS-485 ID of this speed dome e. PRESET-CNT: Preset counter. This counter counts the preset movement, and 1 is counted when the speed dome runs to preset position. f. X-CONT: X-axis counter. This counter counts the x axis movement, and 1 is counted when the speed dome pans 360°. g. Y-CONT: Y-axis counter. This counter counts the y axis movement, and 1 is counted when the speed dome tilts 180°. h. Press IRIS+ key to return to previous menu.
4. EPTZ3100/3100I FUNCTION SETUP AND OPERATION 4.1. Manual Control Mode Manual control: Shift Joystick Up/Down/Left/Right, and turn it Clockwise/Counterclockwise to control speed dome. Use the control keys which are Zoom, Focus and IRIS function keys on the keyboard to Zoom In/Out, focus N (near)/F (Far), or IRIS +/-. Note: Zoom In/Out control keys will be disabled when entering to OSD menu mode.
4.3. Position Setting Focus on a preset position: Press the number key, and then press Position to focus on the number of preset position; or you can press Position, then enter the preset position number, and then press Enter to focus on the number of preset position. Preset a position: Shift the Joystick to the position you would like to preset, and then press Shift + Position. The system will ask you to enter the preset position number (1~192), and then press Enter to save the position.
speed. Dwell time: default is 2 sec; It can be changed by EVF Keyboard Set + A.Pan setting dwell time of A pos or B pos. 99 => Auto scan (360 degree) Default speed is 32. It can be changed by EVF Keyboard (Shift + A.Pan setting speed). We can even set camera’s ICR Day/Night function with RS-485 command via keyboard. How to do this? Press Position + 88 to link to Day mode or Position + 89 to link to Night mode, “ICR AUTO” message will be shown on the right-bottom part of the screen.
One-way tour Mode: Press Tour to enter the tour mode. The system will ask you to enter the tour number you would like to run, and starts the tour after pressing Enter. To preset a tour before running is necessary. Preset a one-way tour: Press Set + Tour to preset a one-way tour. The system will ask you to enter preset position numbers (The positions need to be preset). After finish entering all positions, press Stop to quit, and then press Enter to save the tour.
If you set the position number to 99, the dome will do a 360 degree auto scan or AB two point pan if limit is ON. If you set the position number to 98, the dome will do a frame scan. Delete an alarm link: Press Clr + F1 to delete a link of alarm to position/tour. Note 1: After alarm output signal is terminated, the speed dome will resume action or return to its original position. Note 2: After powering on the speed dome, it will detect alarm status automatically. 4.6.
EverFocus Electronics Corp. Head Office: Europe Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886-2-26982334 FAX: +886-2-26982380 Albert-Einstein-Strasse 1 D-46446 Emmerich, Germany TEL: +49(0)-2822-9394-0 www.everfocus.com.tw FAX: +49(0)-2822-9394-95 www.everfocus.de USA L.A. Office: China Office: 1801 Highland Ave. Unit A Duarte, CA 91010, U.S.A.
