EPN Plus Series IP Speed Dome Quick Installation Guide Copyright © EverFocus Electronics Corp, Release Date: October, 2012
EPN Plus Series 1. Overview The EPN Plus series IP Speed Dome comes in two types: Indoor (EPN4122i Plus / 4220i Plus) and Outdoor (EPN4122 Plus / 4220 Plus). 1 1 2 2 3 3 Outdoor Indoor No. Item Name No. Item Name No. Item Name 1 2 3 Top Housing Outer Housing Camera Main Body Packing List The main box contains 3 large boxes and a small box. Each box contains the items as listed below. Please check that there is no missing item in the package before installing.
EPN Plus Series 3. Cables and I/O Terminal Block Cable Descriptions 1 RS-485+ (Yellow) 2 RS-485- (Orange) 3 24V AC 4 Video Cable 5 Audio In 6 Audio Out 7 No RJ-45 Name and Descriptions No Name and Descriptions 1 RS-485+ (Yellow): Connects to an RS-485 device. 5 Audio In: Connects to a microphone. 2 RS-485- (Orange): Connects to an RS-485 device. 6 Audio Out: Connects to a speaker. 3 24V AC: Connects to the power adapter. 7 RJ-45 Cable: Connects to the network.
EPN Plus Series 4. Optional Accessories • EPTZ-PBOX (External power connection box) • • Corner mount adapter Pole mount adapter • Indoor ceiling pendant mount bracket • Outdoor sunshield • Indoor recessed mount bracket • Wall mount bracket • Indoor concrete ceiling mount adapter • EKB500 (RS-485 keyboard) • EKB200 (USB controller keyboard) 5. Installation This installation guide provides the basic instructions on installing an EPN Plus series IP camera.
EPN Plus Series To replace the desiccant bags: 1. On the Top Housing, slightly press the black plastic socket backward and lift up the base board. 2. Remove the desiccant bags from the top housing. 3. Stick the supplied 3 new desiccant bags inside the top housing. Place back the base board. Note: Ensure Not to place the desiccant bags under the position of the fan. Fan To insert a micro SD card: 1. Unscrew the four screws on the camera main body to remove the black housing. Micro SD Card Slot 2.
EPN Plus Series Installing Outdoor Models (EPN4122 Plus / 4220 Plus) Two mounting types are available for the outdoor models: Wall Mount and Ceiling Mount. Wall Mount 1. Drill 4 screw-depth holes for the bracket base plate and then drill a through-wall hole for the camera cables. You can optionally drill a second through-wall hole to separate cable feeding (see Step 4). 2. Attach the waterproof silicon pad to the bracket base plate for waterproofing. Waterproof Bracket base plate silicon pad 3.
EPN Plus Series Ceiling Mount It is required to use the optional Indoor Recessed Mount Bracket and Surface Ring to attach the camera to the ceiling. 1. Cut a hole on the ceiling using the supplied template. 2. Slightly turn the surface ring and remove it from the bracket. 3. Place and then screw the camera’s top housing on the top disk of the bracket using the 3 short screws. Top Disk 4. Use a cable or other mechanism to hang the bracket on the ceiling.
EPN Plus Series 6. Network Connections You can use one of the methods below to connect the camera to the network. Router or LAN connection This is the most common connection in which the IP camera is connected to a router and allows multiple users on and off site to see the IP camera on a LAN/WAN (Internet). The camera must be assigned an IP address that is compatible with its LAN. By setting up port forwarding on the router, you can view cameras from outside of the LAN via the Internet.
EPN Plus Series Direct High-Speed Connection In a Direct High-Speed Connection, the camera connects directly to a modem without the need for a router. You need to set the static or dynamic WAN IP address assigned by your ISP (Internet Service Provider) in the camera’s configuration web pages. To access the camera, just type “http://xxx”, where xxx is the IP address given by your ISP. If you have a dynamic IP address, this connection may require that you use DDNS for a reliable connection.
EPN Plus Series 7. Assigning an IP Address You can assign an IP address to the camera using the IP Utility (IPU) software, which is included in the software CD. 1. Install and then start the IPU program . The following dialog box appears. 2. Click Find Devices to search the cameras connected in the LAN. The default network values of the cameras will be displayed. By default, the network protocol of the camera is DHCP. 3.
EPN Plus Series 5. To change the IP address, double-click the IP Address of the camera. Type a new IP address and then click Set IP Address to save the settings. You can also change the other settings by double-clicking the values. After configuring the values, click Save Configuration. Note: Most networks support DHCP protocol, but if you are unsure of your network protocol, please consult your IP administrator for network configuration details. 6.
EPN Plus Series 8. Upgrading Firmware You can upgrade camera’s firmware using the IP Utility software, which is included in the software CD. 1. Follow Step 1 to Step 4 in 7. Assigning an IP Address to log in the camera. 2. Highlight the camera and then click Upgrade Firmware. A browsing window appears. 3. Select the firmware file (.evb) and then click Open. The IP Utility will automatically upgrade the firmware. The camera will reboot once the update is complete.
EverFocus Electronics Corp. EverFocus Taiwan: EverFocus Europe - Germany: 12F, No.79, Sec. 1, Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886 2 2698 2334 FAX: +886 2 2698 2380 www.everfocus.com.tw marketing@everfocus.com.tw Albert-Einstein-Strasse 1, D-46446 Emmerich, Germany TEL: +49 2822 93940 FAX: +49 2822 939495 www.everfocus.de info@everfocus.