EHD150 1/3” B/W Rugged Dom e Cam era User’s Manual and Operation Instructions
Notice This manual is presented to the users of EHD150 by EverFocus Electronics Corp. With years of engineering researches, EverFocus has spared no effort to provide the high quality products to the worldwide users. For the policy of continual product improvement, EverFocus reserves the right to make changes to the product specifications and documentation without notice.
Table of Contents Safety Warning … … … … … … … … … … … … … … … … 1 Introduction… … … … … … … … … … … … … … … … … ..2 Specification… … … … … … … … … … … … … … … … … .3 Installation Instructions… … … … … … … … … … .… .… 4 Dip Switch Functions… … … … … … … … … … … .… .
Safety Warning 1. Do not install the camera near electric or magnetic fields. Installed the camera away from TV, radio transmitter, magnet, electric motor, transformer, audio speakers because the magnetic fields generate from above devices will distort the video image. 2. Do not install the camera in the high temperature environment. Installed the camera away from stoves, or other heat generating devices as the high temperature could cause deformation, discoloration or other damages of the camera.
Introduction The most technically advanced EHD150 is the newest vandal-resistant B/W Rugged Dome Camera from EverFocus Electronics. The B/W Rugged Dome Camera can withstand a blow from a 10-pound sledgehammer and has a built-in heater that allows for operation in low temperatures. It is perfect for all high-profile crime-prone applications such as building entrances, retail stores, and shopping malls.
Specification Pickup device: 1/3” interline transfer CCD Picture element: NTSC :768(H) × 494(V) PAL: 752(H)×582(V) Horizontal resolution: 560 TV lines Sensitivity: 0.06 lux / F=1.6 S/N ratio: >48dB(AGC off) Weatherproof ratings: IP66 Electronic shutter: 1/60(1/50)~1/100,000(Board lens only) IRIS Control: Auto (vari-focal lens only) Auto gain control: on/off switch Back light comp: on/off switch Line Lock: on/off switch for 24VAC Gamma correction: 0.45 Video output: 1.
Installation Instructions 1. Loosen the 4 fix screws on the housing cover by using the attached wrench (Figure 1). Carefully uncap the housing cover as the direction shown below (Figure 2), please pay attention not to damage the lens. To remove the housing cover, push the hinges to the bottom of the bracket, the hinges can be easily removed from the bracket. Figure 1 Figure 2 2. Remove the camera.
3. Mounting the base. Side conduit entry Conduit plug setscrew Back conduit entry Mounting Setscrew Mounting Setscrew Mounting Setscrew Mounting Setscrew Figure 4 Attach the base to the wall or ceiling, fix the base by the 4 setscrews attached in the accessory pack. The dome is weighted 1.7kg, please make sure if the mounting is strengthened enough to support it, if not, please reinforce the mounting according to the environment. Note: The diameter of the screw hole isψ4.7mm.
4. Wire Connection Termination Board Micro Switch for Alarm trigger Power In GND Alarm COM Alarm NO V. Phase Adjustment VR Video DC12V (+) or AC24V Power In DC12V (-) or AC24V Alarm NC Figure 6 Connect the power supply cable (AC24V/DC12V), video output and alarm output to the proper connectors shown as Figure 6. The V. Phase adjustment screw is located on the termination board.
5. View Angel Adjustment The camera can be rotated 360°horizontally, and the vertical view angle is 140°(as shown in Figure 7). needed. Adjust the proper camera view angel as If a vari-focal lens is used, you may adjust the focus and zoom of the lens to bring the object in focus. Be sure to loosen the locking screws on the lens before you do the adjustments. .
LL (Line-Lock) Off/On To select the sync mode between Internal Sync.(LL off) and Line-Lock (LL on). Set the line-lock off, the camera will synchronize to the internal time base. Set the line-lock on, the camera’s vertical synchronization can be driven by the AC signal in the power lines.
BLC (Back Light Compensation) On/Normal When BLC is turned on, the AGC, ES and IRIS operating point is determined by averaging over the center area instead of entire field-of-view, so that a dimly-lit foreground object at center area can be clearly distinguished from brightly-lit backgrounds. BLC should not be used unless it is needed to compensate for back-lit. The default setting is Normal.
IRIS Level Adjustment Brightness Level can be adjusted from the IRIS level VR while using the direct drive lens. ? Turn counterclockwise to L to get darker picture. ? Turn clockwise to H to get brighter picture. IRIS ALC Adjustment To select light metering method – ? Turn the IRIS ALC Adjustment VR counterclockwise for Average Metering. ? Turn the IRIS ALC Adjustment VR clockwise for Peak Metering.
EverFocus Electronics Corp. Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chi, Taipei, Taiwan TEL: 886-2-26982334 FAX: 886-2-26982380 http:// www.everfocus.com.tw USA Office: 2445 Huntington Drive, San Marino, CA, 91108 U.S.A. TEL: 1-626-844-8888 FAX: 1-626-844-8838 Toll free: 1-888-383-6287 or 1-888-EV-FOCUS http://www.everfocus.com European Office: Albert-Einstein-Strasse 1 D-46446 Emmerich, Germany TEL: 49-2822-9394-0 FAX: 49-2822-939495 http://www.everfocus.de Hong Kong Office: Room 0, 10/F.