/3” CCD Color Day/Night plus Wide Dynamic Range Outdoor Vandal Dome Camera Operation Instructions Model No. ED610 Please read this manual first for correct installation and operation. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. PRECAUTIONS 1. Do not install the camera near electric or magnetic fields.
TABLE OF CONTENTS 1. PRODUCT OVERVIEW ............................................................................................................... 3 1.1 Main Features ............................................................................................................................................... 3 1.2 Content List................................................................................................................................................... 3 1.3 Specifications ...........
.4.2 AGC (Auto Gain Control)............................................................................................................................ 22 3.4.3 SENSE-UP............................................................................................................................................... 22 3.4.4 BLC ......................................................................................................................................................... 23 3.4.5 HSBLC................
1. PRODUCT OVERVIEW Amazing color low light sensitivity of .05 lux before the added benefits of digital signal processing technology, delivered by a 1/3” Sony Super HAD II sensor, is just the beginning with the new EverFocus ED610. Get color without compromise: 560TVL resolution, your choice of full motion color or true day/night images in low light without ghosting, plus 120dB Digital Wide Dynamic Range to handle the most challenging of bright or unbalanced scene lighting conditions.
Video Test Cable x 1 Power Adapter Cable x 1 Desiccant Pack x 1 Focus Aiding Lens Cap (for 9~22mm models only) x 1 Please Note: If an item appears to have been damaged in shipment, replace it properly in its carton and notify the shipper. If any items are missing, notify your EverFocus Electronics Corp. Sales Representative or Customer Service. The shipping carton is the safest container in which the unit may be transported. Save it for possible future use.
1.3 Specifications Items Pickup Device Video Format Scanning System Picture Elements Horizontal Resolution Sensitivity S/N Ratio Electronic Shutter Video Outputs Gamma Correction Lens Type Back Light Comp. Auto Gain Control White Balance Sync.
1.4 Dimensions 123mm x 107.8mm ; 4.8” x 4.2” Ø 5.143mm//0.2” Ø 94.7mm/3.
1.
1.
(1) External Light Sensor External Light sensor is used to detect the lighting level the environment. (The light sensor is “down” when the internal camera module is properly positioned). (2) Focus Ring To set the focus, and loosen the focus ring knob, and turn the ring toward or as necessary, and re-tighten when the adjustment is complete. (3) Zoom Ring To adjust the viewing angle, loosen the zoom ring knob.
2. INSTALLATION This chapter will describe, in general terms, how to install the ED610 camera. STEPS: 2.1. Mounting Camera: 1. Drill the Holes. See 2.1.1 2. Mounting: See 2.1.2 2.2. Adjusting Camera: 1. Adjust the camera position. See 2.2.1 2. Adjusting Zoom and Focus See 2.2.2 3. Camera Setting. See 2.2.3 4. How to close camera cover after installation. See 2.2.4 Warning • • To prevent electrical shock, turn off the electrical power before making electrical connections.
Wire outlet hole for Surface mounting Power/Video Cable Screw A,B,C Camera base 2.1.2 Mounting 1. Take off camera’s cover by rotating the cover counter clockwise.
2. Pull the cables to be connected to the power and video cables from the ceiling or wall. Video output Power input 3. Fix the camera base to ceiling or wall by using 3 screws and washers. The washers are used to create the IP66 seal and must be used.
Wall Mount: 2.2 Adjusting Camera 2.2.1 Adjusting Camera Position Adjust the camera to best angle for viewing. When you install on the ceiling, change angle of view by turning these joints.
2.2.2 Adjusting Zoom and Focus It is highly recommended to use an EverFocus Test Monitor to set up the camera. Find the Video test connection on the back of the camera module. Connect using the video cable included in the package. Video out Connect with Test Monitor 1. Loosen the zoom ring knob, and then turn the ring towards or as necessary to obtain the desired view angle. W side (Zoom out) The viewing range will be wider and the subject is smaller.
Step 2 Open the dome cover and place the Focus aiding lens cap on the lens, making sure that the cap’s notch is resting on the zoom knob. Step 3 With cap on, adjust the focus and zoom rings by loosening the knobs and turning the rings until subject is in focus. Retighten the knobs when done. Step 4 When finished adjusting focus and zoom, remove the focus aiding cap from the camera lens, replace the dome cover and secure the cover by turning it clockwise. See Section 2.2.4 below for additional information.
2.2.3 Camera Setting 2.2.3.1 OSD User Setup Menu This camera utilizes an On Screen Display (OSD) user setup menu. Please refer to Chapter 3 OSD Menu & Configuration, to get more details about OSD menu usage. 2.2.4 Close the Camera Cover (after installation is complete) The ED610 is specially designed with one inner cover and one outer cover ring for water-proofing and ease of installation. Please follow these instructions for closing the camera cover. 1. Align the window in the cover with the lens 2.
Correct Wrong (not aligned) 3. If the lens is not aligned with the window, loosen the outer cover, adjust the inner cover so that the lens aimed exactly at the window. Slightly adjust the cover 4. Tighten the outer cover ring until it is firmly secured.
3. OSD MENU & CONFIGURATION This chapter introduces how to configure the camera OSD menu. Joystick 3.1 Access the user setup menu screen I. Press inward on the end of the joystick The menu screen will appear on the monitor. II. Navigating with the joystick Angle the joystick or to move the cursor up or down. Angle the joystick or to adjust the mode or value of a setting. III.
3.
- 20 -
- 21 -
3.3 LENS 1. When the SETUP menu is displayed on the screen, please direct the arrow to point to “LENS” by moving the joystick UP and DOWN. NOTE: The brightness of the screen can be adjusted in the BRIGHTNESS sub menu. The level can be adjusted from 0 to 100. 2. Select “RET” to save all settings in the LENS menu and returns to the previous menu. Select “END” to save all the menu settings and exit from the OSD menu. 3.
NOTES: 1 The maximum amplification in low light level situations can be adjusted by pressing the ○ SETUP button in “AUTO” mode. This sets an upper limit on the ‘boost’. 2 The image becomes brighter when the setting increases; however, the after image increases ○ as well. Due to the increased light sensitivity of the Super Had II chip, far less DSP ‘boost’ is needed, resulting in color or B/W images in low light with minimal ghosting.
3.4.5 HSBLC HSBLC (Highlight Suppression BLC) is used to reduce the brightness of light sources in a specific area. It is activated only in a low illumination environment to minimize the effects of glare from bright lights such as spotlights, street lights or headlights in the field of view. Where ‘traditional’ BLC can increase the exposure of a dark area surrounded by a brighter area, HSBLC can decrease the exposure of bright areas surrounded by darker areas. 1.
3.5 WHITE BALANCE CONTROL The screen color can be adjusted by using the WHITE BALANCE function. 1. Please direct the arrow to point to “WHITE BAL” by moving the joystick UP and DOWN. 2. Please select the mode you would like to operate by moving the joystick LEFT or RIGHT. Please select one of the 6 modes below: ATW (Auto Tracking White Balance): This mode can be used within the color temperature range from 5,500°K to 6,000°K (eg, fluorescent light, outdoor, sodium vapor lamp or inside tunnels).
COLOR: The picture is always displayed in color, even at low light levels. AUTO: The picture switches to color in a normal (bright) environment and switches to B/W when the ambient illumination is low. The switching point is determined by the AGC level. Note: AGC selection must be set as middle or high in order to employ the auto switching function. Delay: Set the switchover delay time from 0~63 seconds. S-Level: Set the start level from 0~100. E-Level: Set the end level from 0~100.
6) If you would like to cancel the ID entered, please move the cursor to “CLR”, press in on the joystick, and all the letters entered will be deleted. 7) Select “END” and press in on the joystick to complete the ID input. 3.8.2 D-EFFECT 3.8.2.1 FREEZE (Note that practical application of this feature requires direct access to the camera menu in real time). OFF: Select “OFF” to view moving pictures. ON: Select “ON” to view still pictures. 3.8.2.2 MIRROR OFF: Disable the effects.
ON: D-Zoom: Select digital zoom from X1.0 up to X32. To control the portion of the magnified image in view (0 is the center of the image): Pan: Select pan digital zoom from -100 to 100. Tilt: Select tilt digital zoom from -100 to 100. Return: Select “RET” to save all settings in D-ZOOM menu and returns to the previous menu. Select “END” to save all the menu settings and exit from the OSD menu. 3.8.2.4 GAMMA To adjust displayed brightness from 0.05 up to 1.0. 3.8.2.5 NEG.
3.8.4 PRIVACY This mode covers the areas you do not want to see on the screen. OFF: Disable the PRIVACY function. ON: AREA SELECT: Please select the area you would like to hide from the 8 areas in AREA SELECT mode AREA DISPLAY: Select “ON” to use the area selected in the AREA SELECT. Select “OFF” to disable this function. LEFT/RIGHT: Set the coordinate of the horizontal axis 6~98. WIDTH: Set the size of horizontal area 0~93. TOP/BOTTOM: Set the coordinate of the vertical axis 0~60.
3.9.2 BLUE Adjust image’s blue level. The available range of level is 0~100. 3.9.3 RED Adjust image’s red level. The available range of level is 0~100. 3.9.4 RETURN Select “RET” to save all settings in ADJUST menu and returns to the previous menu. Select “END” to save all the menu settings and exit from OSD menu. 3.10 RESET 3.10.1 FACTORY RESET Reset to the default settings. 3.10.2 RETURN Select “RET” to save all settings in RESET menu and returns to the previous menu. Select “END” to exit from OSD menu. 3.
EverFocus Electronics Corp. Headquarter Office 12F, No.79 Sec.1 Shin-Tai Wu Road, Hsi-Chi, Taipei, Taiwan Tel: +886-2-26982334 Fax: +886-2-26982380 Beijing office Room 609,Technology Trade Building.
