EQN2200 User’s Manual Copyright © EverFocus Electronics Corp, Release: Mar.
EQN2200 Product Name: EQN2200 EverFocus Network Cameras Model Number(s): EQN2200 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
EQN2200 EverFocus Electronics Corp. 12F, No. 79, Sec. 1, Shin-Tai Wu Rd., His-Chi, Taipei Hsien, Taiwan, R.O.C. EQN2200 complies with CE and FCC rules.
EQN2200 About this document All the safety and operating instructions should be read and followed before the unit is operated. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. Safety Notices -These limits are designed to provide reasonable protection against interference.
EQN2200 use a mild detergent and wipe gently. Do not operate the camera beyond its specified temperature, humidity or power source ratings. Do not use the camera in an extreme environment where high temperature or high humidity exists. Use the camera at temperature within 0℃ ~ +40℃ / 32۫F~ 104۫F and a humidity below 90%. The input power source for this camera is 12 VDC & 802.3af PoE. Use only the recommended power supplies.
EQN2200 TABLE OF CONTENTS 1. INTRODUCTION....................................................................................................7 2. FEATURES ..............................................................................................................7 3. SPECIFICATIONS..................................................................................................8 4. ACCESSING THE CAMERA MENU ...................................................................9 5. SETTING...................
EQN2200 1. INTRODUCTION EQN22 series Q-cam is an entry-level network camera which provides competitive price but superior image quality with up to 30fps in 720p (1280x720) resolution. For easy and flexible installation, EQN2200 and EQN2200W offer the choice of either a wireless or a wired connection to the network.
EQN2200 3. SPECIFICATIONS MODEL CAMERA Pickup Device Lens Sensitivity VIDEO STREAMING Video Compression Video Resolution Frame Rate AUDIO Microphone & Speaker Operation Mode NETWORK Interface Supported Protocols Client Limit TERMINAL I/O Alarm Input/Output EVENT MANAGEMENT Event Trigger Notification BUILT IN LIGHT Type Brightness POWER Power Supply Power Consumption PHYSICAL Weight Dimension ENVIRONMENTAL Operating Temp.
EQN2200 4. ACCESSING THE CAMERA MENU Step 1.Start an Internet Explorer browser session. Step 2. Enter the IP address or host name of the camera in the Location/Address field of your Internet Explorer browser in the form http://nn.nn.nn.nn:port, or http://ddnsname.everfocusddns.com. (Please refer to EQN2200 Installation Guide for how to find the IP address by using the IP Finder) Step 3. At the login popup window enter “Username” and “Password”.
EQN2200 3 ○ Press button to close the EQN2200 network page. 4 Video Stream ○ Select the desired Video Stream from Stream 1 / Stream 2, Stream 3 and Stream 4 stream must be enabled in camera Setting menu). Please refer to "Section 4.4.1 Multi Streaming” for further information. 5 View Size ○ You can select View size to either reduce or enlarge the image to the appropriate view size.
EQN2200 9 ~ ○ 10 Play Audio/Transmit Audio ○ Click the “Play Audio” and “Transmit Audio” buttons to switch the sound off and on for the audio input and output, respectively. 11 Manual Control – Trigger Event ○ Press “Trigger Event” button to trigger an event directly from the live view page, and event actions will be initiated if they have been set up in the “Event” menu. (Please refer to “Section 4.7.
EQN2200 5. SETTING Click this button to display the camera setup menu. 4.1 System Info System information and system log events can be accessed on this page via 2 tabs: [Information] tab and [Log] tab. 4.1.1 Information Tab System Information: Firmware version, MAC address, Video Type, Model number.
EQN2200 4.1.2 Log Tab System Log: Date/Time: displays date and time of the log event. Log message: all information and event message, including login, user’s IP, reboot, firmware upgrade, load factory default, configuration reset and event detected. System will keep the newest 256 records.
EQN2200 Press button to export the system log into a “.txt” file and select the location where the exported log file will be saved. 4.2 User Config The configuration and operation of the Live View screen can be changed based on the login user ID. The settings which can be customized for each of the 10 possible login IDs are: Text Setting Check the box to enable display of the Machine name, Date/Time or Frame Rate on the screen.
EQN2200 Press Apply to apply the setting changes or Reset to reset without saving the changes. Date/Time Format Used in Text Select Date/Time Format from the following options: * day of week, Month, date, year Time Format: choose between 24 Hours or 12 Hours. Press Apply to apply the setting changes or Reset to reset without saving the change. Recording/Snapshot Export Setting Enable Event Recording to PC: Allow event video recorded to users' PC if any events have been set to record to PC.
EQN2200 Note: 1. A maximum five languages can be in the language list. 2. Uploading a new language file will reboot the system automatically. Please reconnect to the IP camera after reboot. Press Apply to apply the setting changes or Reset to reset without saving the change. 4.3 Network The network settings and the settings relating to DDNS, Bandwidth, SMTP/FTP and Network Alarm can be configured on this page.
EQN2200 • IP Type • IP address • Subnet mask • Gateway (when using the gateway server/router) • Primary DNS, Secondary DNS (when using DNS) IP Type DHCP: Configure the DHCP server not to assign the same IP addresses used for the other network cameras and PCs whose IP address is unique. Refer to the network administrator for the settings of the server. Default: DHCP. Static IP: User can manually set the static IP for network connection.
EQN2200 An IP address of DNS server that is provided by ISP. This address may be assigned automatically if DHCP is used. A correct DNS IP is essential if DDNS will be used. Secondary DNS If your ISP provides you an IP address secondary DNS, please set it here. Username Enter User name of the account (used only for PPPoE). Password Enter Password of the account (used only for PPPoE). Press Apply to apply the setting changes or Reset to reset without saving the change.
EQN2200 4.3.2 DDNS DDNS setting When accessing the camera via the Internet in a network environment where the site IP address is obtained using DHCP, the DDNS function is necessary. To use the DDNS function, it is necessary to connect to the dedicated DDNS server. We support 4 DDNS server providers as follows: www.everfocusddns.com www.sitelutions.com www.dyndns.com www.no-ip.com ○ ○ ○ ○ 3 3 3 Enable: Check the box to enable DDNS setting.
EQN2200 necessary to configure Record ID, FQDN, Username and password and register in advance for DDNS services. Refer to the web site for further information about the DDNS provider. Press Apply to apply the setting changes or Reset to reset without saving the change. 4.3.3 Bandwidth Bandwidth Setting Max. Bandwidth: Specify, Unlimited / 64 K/ 128 K/ 256 K / 512 K / 1M / 2M / 4M / 8M bps. the maximum bandwidth that the camera is allowed to use on the network.
EQN2200 4.3.4 SMTP/FTP Set SMTP The settings relating to the mail server used to send the e-mail notification from the camera to predefined addresses via SMTP can be configured. SMTP Server: Enter the IP address or the host name of the SMTP server used to send e-mails. SMTP Port: Enter the port number for SMTP. Default is 25. Authentication: Check the box, if the SMTP server requires Authentication (user/ password). User name: Input the login user ID if the SMTP server requires Authentication.
EQN2200 Sender Address: Input sender’s e-mail address, so that receiver can recognize the sender when an event message is sent out. Send Test Mail: Press address. button to send a test e-mail to the designated Set FTP The settings relating to an FTP server to be used to receive alarm images can be configured. FTP Server: Enter the IP address or the host name of the FTP server. FTP Port: Enter the port number for FTP server. Default is 21. Recording Path: Assign the recording path.
EQN2200 4.3.5 Network Alarm (reserved for PowerCon) Set Network Alarm This function is reserved for PowerCon software, for the details regarding these settings please refer to the documentation for the PowerCon network alarm protocol. 4.4 Video The settings relating video such as streaming, camera OSD can be configured on this page. The "Video" page has 2 tabs: the [Multi-streaming] tab and the [Camera] tab.
EQN2200 4.4.1 Multi Streaming Stream Setting The system can output 4 video streams simultaneously. For each of them, the user can set compression format, resolution, quality and frame rate individually. Stream 1 is always enabled for live view. Check “Enable” box to enable other streams. Format: Select compression format from H.264, MPEG4 and MJPEG.
EQN2200 Note: Total frame rate cannot exceed 60 fps. System performance may be influenced if user enables 4 video streams simultaneously. Press Apply to apply the setting changes or Reset to reset without saving the change. Video Recording Setting User can set video recording by selecting one of the enabled video streams. This will allow users to view live images while also recording video from another video stream. Video Stream: Select video recording stream from any enabled stream.
EQN2200 configured using the operation buttons on this tab. OSD setting: Use the following buttons on the operation panel to operate the "Camera OSD setting" remotely from a PC. (Please refer to Section 4.4.2.1 for a detailed guide to the Camera OSD Setting menu) [SET] button: Click this button to select choices or to bring up the menu and submenus. [Left] button/ [Right] button: Click these buttons to change or select the parameters. [Down] button/ [Up] button: Click these buttons to move the cursor.
EQN2200 4.5 Audio The EQN2200 camera can transmit audio to client PCs by connecting an external source (line-in), and can play audio received from clients PCs (line-out) into amplified speakers. This section describes how to configure the basic audio settings. Audio Check Enable Audio box to enable audio function. Audio Input: Audio from an internal microphone or a line source can be connected to the Audio connector of EQN2200.
EQN2200 4.6 USER User Information Maximum 10 user IDs can be created to access the IP camera. The user information screen displays the authorized IDs. Access levels are: • Supervisor/Administrator –a supervisor/administrator has unrestricted access to the Setting menus and can determine the registration of all other users. However, an administrator is not allowed to change a supervisor’s account and password.
EQN2200 4.7 EVENT An event in the camera is when an Event Type is activated and causes certain actions to be performed. The event type is the set of conditions that specifies how and when which actions will be performed. This table describes how to setup action types and event type.
EQN2200 4.7.1 Event The settings relating to event occurrences such as settings for motion, alarms and time mask can be configured on this page. The "Event" page has 4 tabs: [Event] tab, [Motion] tab, [Alarm] tab and [Time Mask] tab. Press button to add an event condition. To modify the event list, click on the event and it will be highlighted. Press button to modify the setting. To remove an event from event list, click on the event and it will be highlighted. Press button to remove the event.
EQN2200 or button to change the priority of events. The event that has highest priority will be activated first. Press Apply to apply the setting changes or Reset to reset without saving the change. This example describes how to set the camera to upload images to an FTP site when someone press Manual trigger button: button in Event page. 1. Click 2. Enter an event name for the event, e.g. Event 1 3. Select “Manual Trigger” as event type. 4. Select “Upload to FTP” as action type. 5.
EQN2200 post alarm buffer setting, please refer to “4.7.3 Alarm”. 6. Check “Enable This Event”. 7. Select “Always” for time mask. For detail about Time Mask, please refer to “4.7.4 Time Mask”. 8. Click to save this event in event list. 4.7.2 Motion Motion Detection Users can define the motion areas to be detected by left clicking the mouse to draw lines. Every click is an end point of the line. When the detection area is formed, double click the mouse to have all the lines connected.
EQN2200 There are 5 possible motion trigger areas, which can be distinguished by 5 different colors. Check the Enable checkbox to enable event actions related to that area. For each area, you can set the event action in response to motion detection in that area. Event actions can be set in “Event” section. In addition, you can set the Sensitivity level for the motion trigger separately for each area by selecting from 1 (low), 2, 3, 4, 5, 6, 7, 8, 9 to 10 (high). 4.7.
EQN2200 motion detection ceases. Pre-Alarm Buffer: Image saved internally in the camera from the time immediately preceding the trigger. Input the desired length of pre-trigger buffer time. It can be set up to 120 seconds. Post-Alarm Buffer: Image saved internally in the camera from the time immediately after the trigger condition has ceased/been reset. Input the desired length of post-trigger buffer time. It can be set up to 120 seconds.
EQN2200 Time Mask Setting Time mask setting allows you to schedule the times when the system will respond to event actions. Select Always for event action to be taken continuously. Press button to add new time period. Mask name: Input a mask name for the new time period. Check the check box for the day to be scheduled: Sun, Mon, Tue, Wed, Thu, Fri & Sat. Set the Start time and End time for time mask by clicking Up arrow or Down arrow. Or simply press Press for a full day of event action.
EQN2200 4.8 SYSTEM Date/Time, Daylight Saving, SD card and Maintenance settings can be accessed on this page. The "System" page has 4 tabs: [Date/Time] tab, [Daylight Saving] tab, [SD card] tab and [Maintenance] tab. 4.8.1 Date/Time Machine Name Setting Machine Name: Enter the name for the camera. The entered name will be displayed in the status display area, and used to label any recoding and/or snapshot folders created on a user’s PC.
EQN2200 Set Date/Time Manually Date: Click the calendar and pick the date. Press << to go previous year, < to go previous month, > to go next month and >> to go next year. Time: Click on Hour, Minute, Seconds, am/pm; then use up arrow to increase value and down arrow to decrease value. Press Apply to apply the setting changes or Reset to reset without saving the change. Set Date/Time Sync. Check Enable NTP checkbox to enable NTP server.
EQN2200 4.8.2 Daylight Saving Set Daylight Saving Check Enable Daylight Saving checkbox to enable daylight saving. Set the start time for daylight saving time.
EQN2200 Press Apply to apply the setting changes or Reset to reset without saving the change. 4.8.3 SD Card Setup SD Card NEED A DIAGRAM SHOWING WHERE/HOW TO INSERT THE CARD (it’s displaying in installation guide) Notification: Notification will be made via e-mail when the remaining space of the SD memory card reached the value selected from the following.
EQN2200 connection to the FTP server is unavailable. Normal: Follows the event action settings you have made in the “Event” menu to record event video to the SD card. Overwrite: Select ON for overwriting older data when the SD card memory is full. Select OFF for not overwriting the SD card data. Note: no recording can take place if the SD card is full and Overwrite is “Off”. Press Apply to apply the setting changes or Reset to reset without saving the change.
EQN2200 Note: - It is impossible to access the SD memory card in the process of formatting. - All data saved on the SD memory card will be deleted when the SD memory card is formatted. - Do not turn the power of the camera off in the process of formatting. 4.8.4 Maintenance Maintenance Tab Reboot: The unit is rebooted without changing any of the settings. Use this method by pressing Reboot button if the unit is not behaving as expected.
EQN2200 To take a backup of all of the settings in the current configuration, press Save to save the configuration to a config. file. Once saved, it is then possible to return to the previous settings if/when desired. To return to a previously saved configuration, press the Browse button to locate and select the saved config. file (see above) and then click the Load button. The settings will be restored to the previous configuration. Upgrade Firmware Upgrade the EQN2200 with the latest firmware.
EQN2200 43
EQN2200 44 EverFocus Electronics Corp.
