User Manual

ManualsBrandsEverdure by Heston Blumenthal ManualsGas GrillsFORCE Gas Grill - Orange

Assembly, Operation & Maintenance InstructionsAssembly, Operation & Maintenance Instructions

Barbeque

FORCE

FURNACE

Barbeque only LENGTH

(mm)

WIDTH

(mm)

HEIGHT

(mm)

LENGTH

(mm)

WIDTH

(mm)

HEIGHT

(mm)

1170 515 410 1310 515 410

Barbeque and

stand

1170 750 1170 1310 750 1170

Barbeque

FORCE

FURNACE

Barbeque only LENGTH

(ft)

WIDTH

(ft)

HEIGHT

(ft)

LENGTH

(ft)

WIDTH

(ft)

HEIGHT

(ft)

4 1.7 1.3 4.3 1.7 1.3

Barbeque and

stand

4 2.5 4 4.3 2.5 4

GAS CONNECTIONS

BUTANE & PROPANE GAS REQUIREMENTS

Check Gas Type and specications plate on the underside of the RHS servery.

FOR GAS CYLINDER CONNECTION

1. To achieve the optimum performance from your barbeque, an approved gas cylinder/

bottle must be used. The supplied hose and/or regulator must rst be connected to the

barbeque inlet.

2. Do not connect a gas cylinder/ bottle to a barbeque that is not secured in the supplied

stand or on a stable raised surface. The cylinder should be lower than the barbeque, in

a protected place on a stable surface.

3. Before connecting gas supply, take care that all gas control knobs are in the o position.

Once connected, turn the regulator handle to on to turn on the gas supply. Check all

joints are secure.

NOTE: Only one gas cylinder should be stored on the stand at any one time.

LEAK TESTING

1. Make sure the gas control knob is O and turn the cylinder valve On.

2. Check for leaking joints by brushing with solution of half-liquid detergent and half water.

If a leak is present, bubbles will appear (or you may hear a hissing sound). Retightening

connections can generally repair a leaking joint. You must also check the gas hose and

connection at the gas cylinder. If a leak cannot be resolved, do not proceed and turn

the gas cylinder/bottle valve o.

SPECIAL INSTRUCTIONS FOR THE USE OF

REGULATOR AND PROPANE CYLINDER

GAS HOOK-UP: Only the pressure regulator and hose assembly supplied with the grill

should be used. Any replacement pressure regulator and hose assembly must be specied

by the grill manufacturer. This grill is congured for Liquid Propane. Do not use a Natural Gas

supply.

LIQUID PROPANE CYLINDER REQUIREMENTS: (The LP cylinder must be a 20-lb). A

dented or rusty Liquid Propane cylinder may be hazardous and should be checked by your

supplier. Never use a cylinder with a damaged valve. The Liguid Propane cylinder must be

constructed and marked in accordance with the specications for Liquid Propane cylinders

by United States Department of Transportation (DOT) or the National Standard of Canada,

CAN/CSA-B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods

Commission. The 20-lb cylinder must have a shut o valve terminating in a valve outlet

specied, as applicable, for connection type QCC1 in the standard for compressed gas

cylinder valve outlet and inlet connection ANSI/CGA-V-1. Storage of an outdoor cooking

gas appliance indoor is permissible only if the cylinder is disconnected and removed from

the outdoor cooking gas appliance. The cylinder system must be arranged for vapor

withdrawal. The cylinder must include a collar to protect the cylinder valve. Manifold

pressure: (operating) 11 inches water column (W.C.), (non-operating) 11.2 inches water

column (W.C.). The Liquid Propane cylinder must be tted with an Overll Protection

Device (OPD). Remove the plastic valve cover from the Liquid Propane cylinder is placed

into the cart.

DO NOT USE NAKED FLAME FOR LOCATING GAS LEAKS.

IF A LEAK PERSISTS CALL AN AUTHORISED GAS FITTER.

APPLIANCE DETAILS

PROPANE

MODEL

DESIGNATION

COUNTRIES

BURNERS COUNTRY GAS