Assembly, Operation & Maintenance Instructions FO R C E T M FUR NAC E T M Assembly, operation & maintenance instructions for Everdure by Heston Blumenthal FORCE™ & FURNACE™ gas barbeques and stands everdurebyheston.
Assembly, Operation & Maintenance Instructions DANGER If you smell gas: • Shut off gas to the appliance. • Extinguish any open flame. • Open lid. • If odor continues, keep away from the appliance and immediately call your fire department. Failure to follow these instructions could result in fire or explosion which could cause property damage, personal injury or death. CONTENTS Important Safety Instructions ......................................................................... 4-5 Appliance Details ....
4 Assembly, Operation & Maintenance Instructions IMPORTANT SAFETY INSTRUCTIONS This instruction manual contains important information necessary for the safe use of this appliance. Read and follow all warnings and instructions before assembling and operating this appliance. WARNING: Accessible parts may be very hot. Keep young children away 1. This gas barbeque and stand set are intended for USE OUTDOORS ONLY. This appliance must NOT be used indoors. 2.
6 Assembly, Operation & Maintenance Instructions Assembly, Operation & Maintenance Instructions APPLIANCE DETAILS GAS CONNECTIONS PROPANE MODEL DESIGNATION HBG2GUS BUTANE & PROPANE GAS REQUIREMENTS DESIGNATION COUNTRIES MINT HBG2RUS RED HBG2OUS ORANGE HBG2SUS STONE HBG3GUS GRAPHITE HBG3MUS MINT HBG3OUS ORANGE HBG3SUS STONE Barbeque and stand OUTPUT INJECTOR SIZE HOSE 1. To achieve the optimum performance from your barbeque, an approved gas cylinder/ bottle must be used.
8 Assembly, Operation & Maintenance Instructions CONNECTING THE LIQUID PROPANE CYLINDER: To connect the Liquid Propane gas supply cylinder: The cylinder valve should be in the “OFF” position. If not, turn the valve clockwise until it stops. Make sure the cylinder valve has the proper type-1 external male thread connections per ANSI Z211.81. Make sure the burner valves are in the “OFF” position.
10 Assembly, Operation & Maintenance Instructions Assembly, Operation & Maintenance Instructions LIGHTING PROCEDURE STORAGE READ ALL OPERATING INSTRUCTIONS BEFORE LIGHTING THE APPLIANCE OPEN THE HOOD BEFORE LIGHTING When the appliance is not in use, the cylinder valve must be turned OFF, the barbeque, stand and the cylinder together must be stored outdoors in a well ventilated area. However it is permissible to store the appliance (but not the cylinder) indoors.
12 Assembly, Operation & Maintenance Instructions Assembly, Operation & Maintenance Instructions TROUBLESHOOTING BARBEQUE AND STAND ASSEMBLY Burner will not ignite when using the igniter: The barbeque and hood come fully assembled. To assemble, the stand must first be built (note: for transportation reasons, the barbeque is packaged bolted to the stand top, and should be removed before attempting to assemble the stand).
14 Assembly, Operation & Maintenance Instructions STEP 01 /Open the hood and fix the hood handle (15) using two M5x0.6in (15mm) screws (F), two Ø0.2in (5mm) spring washers (C) and two Ø0.2in(5mm) flat washers (G). Tighten in place. Assembly, Operation & Maintenance Instructions Angle the assembly slightly to the back and remove both M6x0.8in (20mm) screws, then do the same at the front, supporting the parts so they don’t drop. Keep all of the fasteners for later use.
16 Assembly, Operation & Maintenance Instructions STEP 07 / Position the stand with the castor wheels to the right. Two people should lift the barbeque and hood assembly (01A) by the serveries, and place it within the stand (facing forwards, castors to the right). Fix the barbeque to the stand top with the four M6x0.8in (20mm) screws and 0.2in (6mm) flat washers removed at step 2 – two to the front and two to the rear. Tighten fully.
18 Assembly, Operation & Maintenance Instructions MAINTENANCE It’s recommended that you undertake the following maintenance program every 12 months or prior to the use of your grill at the beginning of every BBQ season. Assembly, Operation & Maintenance Instructions STEP 012 /Slide the burners toward the rear of the grill & remove ignition cables from the burner assembly and lift the burner rail assembly out of the gas grill.
20 Assembly, Operation & Maintenance Instructions CHECKING THE BURNERS FOR FLAME STABILITY: Visually check the burner flames for correct function when the unit’s operating by inspecting the burner flame / flames with the cooking plates & grills removed. A good flame should be blue with some yellow tipping. Note: take care when viewing the burner operation not to lean into the flame, failure to do this may result in personal injury.
Assembly, Operation & Maintenance Instructions 22 PARTS LIST: FORCETM BARBEQUES PART NAME 1 Hood HBG2 (Orange) 1 Hood HBG2 (Mint) 1 Hood HBG2 (Stone) 2 QTY 1 Hood HBG2 (Graphite) 1 Hood HBG2 (Red) 1 Temperature Gauge Bezel 1 3 Temperature Gauge 1 4 Hood Handle Spacer 2 5 Hood Handle 1 6 Hinge 2 7 Right Hand Burner (HBG2) 1 8 Hardware Kit (not shown) 1 9 Barbeque Chassis (HBG2) 1 10 Control Knob 2 11 Control Knob Bezel 2 12 Right Hand Side Servery (HBG2) 1 13 G
Assembly, Operation & Maintenance Instructions 24 PARTS LIST: FURNACETM BARBEQUES PART NAME 1 Hood HBG3 (Orange) 1 Hood HBG3 (Mint) 1 Hood HBG3 (Stone) 2 QTY 1 Hood HBG3 (Graphite) 1 Hood HBG3 (Red) 1 Temperature Gauge Bezel 1 3 Temperature Gauge 1 4 Hood Handle Spacer 2 5 Hood Handle 1 6 Right Hand Burner (HBG3) 1 7 Hinge 2 8 Hardware Kit (not shown) 1 9 Barbeque Chassis (HBG3) 1 10 Control Knob 3 11 Control Knob Bezel 3 12 Right Hand Side Servery (HBG3) 1 13
26 Assembly, Operation & Maintenance Instructions Assembly, Operation & Maintenance Instructions FORCE TM 2 BURNER GAS BARBEQUE HBG2OUS HBG2GUS HBG2SUS HBG2RUS HBG2MUS FURNACE TM 3 BURNER GAS BARBEQUE IM Ref: FORCE&FURNACEUS 11/2016/30 FOR OUTDOOR USE ONLY HBG3SUS HBG3OUS HBG3MUS HBG3GUS eve rd u re byh e s to n .
