E334518W Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Installation Guide BEFORE YOU START Please Read the instructions carefully to familiarize yourself with every detail and step involved. Keep this manual for future reference. Find a suitable space to assemble the Everbloom Garden Bed. You need at least 46” x 19” (117 x 49cm) for the finished product. A flat and firm area (like a garage floor or flat yard space) is perfect! The only tool you may need is a rubber mallet.
PARTS LIST Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Left Corner Right Corner Post Post X2 X2 Bottom Short Board A X2 Short Board B X2 400mm 400mm Bottom Board X4 5 holes Top 440mm Bottom 1140mm Post Cap X8 Long Support Board X2 8 holes 8 holes 5 holes Top Long Board X2 Caster Wheel X4 Bolt X4 1140mm Nut X4 Nut Driver X1 Hex Key X1 Garden Bed Liner X1
ASSEMBLY 1 Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Start by making sure each corner post is oriented correctly. Refer to image 1 and ensure that the 8 holes are on the bottom half of the standing corner posts. Slide one short board B into the corner brackets from above. Note: The short boards need to be placed in the inward “U” shape of the brackets. (Image 2).
ASSEMBLY 2 Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Slide the long support boards into the corner posts, as shown in Image 3.
ASSEMBLY 3 Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Carefully flip over the garden bed so that it lays flat with the long support boards pointing towards the sky. Slide the bottom boards through the slots of the long support boards. All 4 boards can be slided in now.
ASSEMBLY 4 Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Slide the remaining corner posts into place as shown in Image 5. Ensure that the direction of the each post is symmetric for the remaining short board.
ASSEMBLY 5 Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Slide one short board B into the corner brackets, as shown in Image 6.
ASSEMBLY 6 Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Flip over the bed so it stands upright. Slide the remaining boards into place, as shown in image 7.
ASSEMBLY 7 Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Use the rubber mallet to ensure the boards are tightly in place. Cover the brackets with the 8 end caps, as shown in Image 8.
ASSEMBLY 8 Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Carefully flip over the garden bed again so that it lays flat with the long support boards pointing towards the sky. Insert caster wheels into corner brackets, as shown in Image 9 and Image 10.
ASSEMBLY 9 Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Fix the wheels with bollts and nuts, as shown in Image 11.
ASSEMBLY 10 Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Fasten bolts and nuts with nut driver and hex key which are included in pack , as shown in Image 12.
ASSEMBLY 11 Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Flip over the bed again so it stands upright, as shown in Image 13.
ASSEMBLY 12 Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Unfold the liner and cover the bottom of the garden bed, as shown in Image 14 and Image 15.
Notes 13 Elevated Garden Bed, wheeled 45” L x 18” W x 33" H Sometimes there might be mis-alignment of corner brackes as showed in Image 15 and Image 16, which may result in difficulty of sliding boards into the bracks. Please adjust them to the right position.
Questions or Comments? Email us at service@everbloom-garden.com Welcome to our website: www.everbloom-garden.com Distributed by: Dynaforge Trading LLC St. Paul, MN55101 Email: service@everbloom-garden.
