Item # 1002 782 613 Model # 9236061 INSTALLATION INSTRUCTION 21 IN. UNDERMOUNT RUNNER Questions, problems, missing parts? Before returning to the store, call Everbilt Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday 1-800-305-1726 THANK YOU 924 395 600 or refer to HOMEDEPOT.
Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Is this the right drawer for my project? . . . . . . . . . . . . . . . . . 3 Pre-Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Planning Installation . . . . . . . . . . . . . . .
Installation Options 1 Is this the right slide for my project? Please check the following points Drawer dimensions need to be met to fit slides Fits 21 in. deep drawers These slides can be installed in frameless and face frame cabinetry. Instructions for both options are provided in this manual. The drawer side thickness can be 1/2 in. (13 mm) or 5/8 in. (16 mm), but no thicker.
Pre-Installation PLANNING INSTALLATION Ensure all parts listed in the Package Contents section are included and that you have the listed Tools Required on hand. TOOLS REQUIRED Pencil Drill with 3/32" Drill bit for screws 1/4" Drill bit for rear hole Phillips Screwdriver Measuring Tape PACKAGE CONTENTS A B C E *May be placed right side up as well.
Dimensions Please review these diagrams and measure and mark your installation location before you begin the installation procedures. DRAWER DIMENSIONS Cabinet opening height Inside Cabinet Width (ICW) Drawer height CABINETRY DIMENSIONS 1-15/32" (37 mm) Drawer side thickness 1/2" (13 mm) or 5/8" (16 mm) Outside drawer width Inside drawer width 1-3/16" (30 mm) 13/16" (21 mm) Drawer depth: 21 in.
Face Frame Installation 1 Preparing the slides A /B Slide plastic connector from rear metal bracket into the notch on the left and right drawer slides (A and B) forward, as shown. 2 Face frame application Cabinet front edge 3/8" (10 mm) Setback 3/32" (2 mm) Front gap 1/16" (1.5 mm) Face frame application with overlay decorative front Minimum/maximum cabinet depth (see below) Inset application increases minimum cabinet depth by thickness of decorative front.
Face Frame Installation 3 Metal rear attachment set (screw-on) Set contains 2 metal rear mount brackets and 2 plastic connectors Non-handed, two-piece design For up to 50 mm (1 15/16") depth adjustment and ± 1,5 mm (1/16") side adjustment Additional adjustment via oblong holes Installation recommended with minimum of four panhead screws (F) * Center of rear bracket * Center of rear bracket 3/8" (10 mm) 11/32" (9 mm) 25/32" (20 mm) 5/16" (8 mm) 3/8" (10 mm) Face frame Face frame * Center of the meta
Frameless Installation 1 Frameless application Cabinet front edge 1 7/16" (37 mm) Min. 5/8" (16 mm) 3/8" (10 mm) Setback 3/32" (2 mm) Front gap 1/16" (1.5 mm) Frameless application with overlay decorative front Minimum cabinet depth (see below) Inset application increases minimum cabinet depth by thickness of decorative front.
Drawer Installation and Removal 1 Installing the drawer catches Install each drawer catch (C) into the two front corners of the drawer using #6 x 3/4 in. screws (H) or #6 x 1 in. screws (I). If you need to install the screws at an angle, do not angle the screws more than 30°. If your door subfront is 1/2 in. (13 mm) use the optional spacers (D).
Questions, problems, missing parts? Before returning to the store, call Everbilt Customer Service 8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-800-305-1726 HOMEDEPOT.COM For the most up to date instructions - please visit HomeDepot.com. Retain this manual for future use.
