Installation Guide

ManualsBrandsEverbilt ManualsCloset OrganizersGenevieve 6 ft. Gray Adjustable Closet Organizer Double Long Hanging Rod with Shoe Rack, 6 Shelves, and 2 Drawers

73.5 in. Double Long Hang with Shoe Rack, Six Shelf Stack and

Two Drawers ( One Large and One Small)

SKU#: 1008446114 / 1008446099 / 1008446085

Summary of content (23 pages)

PAGE 1
73.5 in.
PAGE 2
INSTRUCTION TABLE OF CONTENTS: • Quick Start Guide • 73.5 in. Long Hang with Shelf Stack – Base Kit • 49 in. White / Gray / Birch Shoe Rack • 48 in. x 16 in. White / Gray / Birch Shoe Rack • 24 in. White / Gray / Birch Décor Shelf Cover • 24 in. x 16 in. Large Drawer Kit, White / Gray / Birch • 24 in. x 16 in.
PAGE 3
Quick Start Guide Look for packet in this ‘BASE KIT’ box labeled “Modular Configuration Guide”, find your layout in the packet, and make sure you received the correct number of boxes and contents to build your specific layout. 1. First, find the “Assembly and Installation” instructions for building your ‘BASE KIT’ in this base kit box. a) Measure your space to make sure the complete closet design will fit. b) Be sure to install the ‘Base Kit’ at the furthest left side of your closet space.
PAGE 4
Item # 1006-844-947 Model # 90441 ASSEMBLY AND INSTALLATION GUIDE 73.5 IN. LONG HANG WITH SHELF STACK - BASE KIT Questions, problems, missing parts? Before returning to the store, call Everbilt Customer Service 8 a.m. – 7 p.m., EST, Monday-Friday, 9 a.m. – 6 p.m., EST, Saturday 1-800-305-1726 HOMEDEPOT.COM THANK YOU We appreciate the trust and confidence you have placed in Everbilt through the purchase of this closet organizer.
PAGE 5
Table of Contents Table of Contents..........................................................2 Installation ......................................................................6 Install Hang Tracks...................................................................6 Install Upper Vertical Rails.......................................................6 Install Vertical Rail Joiners and Lower Vertical Rails................7 Install Brackets......................................................................
PAGE 6
Pre-installation PLANNING INSTALLATION 1. 2. 3. 4. Measure the closet width and plan the layout. See the “Plan Your Closet Layout” section for illustration examples. Select the correct hardware for assembly. See "choose your hardware" section below. Use stud finder to locate the studs and mark. It is recommended to mount hang tracks onto studs.
PAGE 7
Pre-installation (continued) CHOOSE YOUR HARDWARE DRYWALL DD Drill a 1/2 in. hole in the drywall. If you hit a stud during drilling, use above stud hardware/instructions for each stud location. CC Insert bolt through hang track (or vertical rail/vertical rail joiner) then screw on toggle (DD). Install toggles (DD) in each hole of the component you are attaching before attaching to the wall. Compress and pass the toggle (DD) through the hole you drilled.
PAGE 8
Plan Your Closet Layout When planning your installation, measure the dimensions of your installation location. For specific designs refer to separate Modular Closet System Configuration Guide. TIP: Shelf height can be adjusted per your personal needs. NOTE: All vertical measurements are taken from the floor. 5 HOMEDEPOT.COM Please contact 1-800-305-1726 for further assistance.
PAGE 9
Installation 1 Install Hang Track □ Use a stud finder to locate and mark your studs if installing on drywall. □ Place the longest hang track (C) flush against the wall, the bottom of the track should be 84 in. off the ground. The thicker side should be on top, closest to the ceiling. TIP: When creating larger closet layouts that include multiple hang tracks, install this kit hang track to the far-left of your planned closet design.
PAGE 10
Installation (continued) 3 Install Vertical Rail Joiners and Lower Vertical Rails SCENARIO 1: STUD □ Push vertical rail joiner (I) up into upper vertical rail (A) as shown, secure the vertical rail joiner (I) on hole B with panhead screw (#12 x 2 in.) (see Fig. 5). □ Put the lower vertical rail (B) as shown and secure the lower vertical rail (B) on the hole C and D with panhead screw (#12 x 2 in.) (see Fig. 6).
PAGE 11
Installation (continued) SCENARIO 3: DRYWALL □ Tear the drilling template box (P) according to the dashed line (see Fig. 14). □ Align the drilling template box (P) as a locator as shown and mark the holes on the wall (see Fig. 15). □ Drill 1/4 in. holes for hole B and C, drill 1/2 in. hole for hole D. Insert wall anchors (1/4 in.) into hole B and C (see Fig. 16).
PAGE 12
Installation (continued) 5 Install Shelves 2 □ Make sure your shelves (G) fit your closet layout design. □ Hold the shelf’s (G) front rod, let it fit into the bracket’s (H) front notches as the diagram shows, then push down the shelf’s rear part allowing the shelf’s rear horizontal rod to lock into the back clip of bracket. 1 H Two shelves share one bracket NOTE: The bracket is supposed to be shared by two shelves in system as shown on the right. Each end of shelf will take up half of bracket.
PAGE 13
Installation (continued) 7 Install Closet Rod End Caps N M □ Measure length of closet rod assembly needed based on your closet layout. □ Push end caps (N) into both ends of closet rod (L) (see Fig. 9). □ Position closet rod assembly at desired location and snap into closet rod brackets (M) (see Fig. 10 and Fig. 11). L J K Fig. 89 Fig. L M NOTE: Make sure to complete joiner assembly (if needed based on layout) before adding end caps to the finished ends of closet rod. Fig. Fig.
PAGE 14
Questions, problems, missing parts? Before returning to the store, call Everbilt Customer Service 8 a.m. – 7 p.m., EST, Monday-Friday, 9 a.m. – 6 p.m., EST, Saturday 1-800-305-1726 HOMEDEPOT.COM Retain this manual for future use.
PAGE 15
Item #1006-844-927 / 1006-844-921 / 1006-844-911 Model #90451 / 90453 / 90455 Assembly and Installation Guide 49 in. White / Gray / Birch Shoe Rack - Add-On PARTS LIST B A C D Part A Description 49 in. x 12 in. Wire Shelf Quantity 1 B Shoe Shelf Bracket 3 C 49 in. Décor Shoe Shelf Cover 1 D Décor Shoe Shelf Cover Endcap Set (both ends) 1 Installation NOTE: PLEASE REMOVE PROTECTIVE FILM (TWO SIDES) BEFORE INSTALLATION. 1 2 B Center-to-center spacing 24 in. (60.
PAGE 16
Item #1007-781-988 / 1007-782-044 / 1007-782-347 Model #90677 / 90679 / 90681 Assembly and Installation Guide 48 in. White / Gray / Birch Shoe Rack - Add-On PARTS LIST A B Part A B C D E E C D Description Quantity 48 in. x 16 in. Wire Shelf 1 16 in. Shoe Shelf Bracket 3 48 in. Décor Shoe Shelf Cover 1 Décor Shoe Shelf Cover End cap Set (both ends) 1 Shoe Shelf Bracket Clip 6 Installation NOTE: Please remove protective film on the decor shoe shelf cover before installation.
PAGE 17
Item #1006-841-112 / 1006-841-104 / 1006-841-024 Model #90442 / 90444 / 90446 Assembly and Installation Guide 24 in. White / Gray / Birch Décor Shelf Cover (2-Pack) PARTS LIST B (Right) Part A Description 24 in. Décor Shelf Cover Quantity 2 B Décor Shelf Cover Endcap Set (both ends) 2 A B (Left) Installation 1 REMOVE PROTECTIVE FILM (TWO SIDES) BEFORE INSTALLATION. 2 PUT ON ENDCAPS (B) AS SHOWN BELOW (SINGLE OR CONNECTED).
PAGE 18
Item # 1007-775-352 / 1007-775-625 1007-775-795 / 1007-775-807 1007-775-821 / 1007-775-837 Model # 90670 / 90671 90672 / 90673 90674 / 90675 ASSEMBLY AND INSTALLATION GUIDE 24 IN. X 16 IN. WHITE / GRAY / BIRCH DRAWER KIT-ADD-ON Vertical rails (not included) Questions, problems, missing parts? Before returning to the store, call Everbilt Customer Service 8 a.m. – 7 p.m., EST, Monday-Friday, 9 a.m. – 6 p.m., EST, Saturday 1-800-305-1726 HOMEDEPOT.
PAGE 19
Table of Contents Table of Contents..........................................................2 Installation ......................................................................4 Safety Information.........................................................2 Install Handles.........................................................................4 Product Specifications.................................................2 Install Brackets.......................................................................
PAGE 20
Pre-installation PLANNING INSTALLATION 1. If installing 2 or more drawer kits, install bottom drawer kit first. 2. Drawer kit is heavy. It is recommended to install the drawer kit on the brackets with two people. 3. Please remove all packaging paperboards from inside the drawer kit before installation. COMPONENT PACKAGE CONTENTS A B C D E Part A Description Drawer Kit Quantity 1 B 16 in. Heavy Duty Multi Bracket 2 C 16 in.
PAGE 21
Installation 1 Install Handles D A E 2 Install Brackets 1 2 B 4 HOMEDEPOT.COM Please contact 1-800-305-1726 for further assistance.
PAGE 22
Installation (continued) drawer kits 3 Install on the bracket A 1 2 NOTE: Please remove all packaging paperboards from inside the drawer kit before installation. Insert to the end of groove. B bracket 4 Install covers C A 1 2 B Care and Cleaning Everbilt closet organizer is powder coated and drawer kit is made of particle board.
PAGE 23
Questions, problems, missing parts? Before returning to the store, call Everbilt Customer Service 8 a.m. – 7 p.m., EST, Monday-Friday, 9 a.m. – 6 p.m., EST, Saturday 1-800-305-1726 HOMEDEPOT.COM Retain this manual for future use.