PELLET HEATER OWNER’S MANUAL WARNING: FOR OUTDOOR USE ONLY ASSEMBLY AND OPERATING INSTRUCTIONS SAVE THIS MANUAL FOR FUTURE REFERENCE Model HTR1085AS WARNING NOTICE TO INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE HEATER OWNER FOR FUTURE REFERENCE. PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET FUELBURNING APPLIANCE. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH.
IMPORTANT SAFETY WARNINGS WE WANT YOU TO ASSEMBLE AND USE YOUR HEATER AS SAFELY AS POSSIBLE. THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO ATTRACT YOUR ATTENTION TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR HEATER. WHEN YOU SEE THE SAFETY ALERT SYMBOL, PAY CLOSE ATTENTION TO THE INFORMATION WHICH FOLLOWS! READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING AND OPERATING YOUR HEATER. WARNING 1.
TABLE OF CONTENTS: General Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Operating the Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Proper Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Transporting and Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Assembly Instructions . . . . . . . . . . . . . . . . . . . . .
GENERAL WARNINGS: WARNING When using, basic safety precautions should always be followed including the following: • Always place heater on a level non-combustible surface. • Operate only per manufacturers instructions. • Keep all combustible materials at least 36 inches (66 cm) away from the heater at all times. Do not use this heater under any overhang or near any combustible structures.
Follow these guidelines to prevent this colorless,odorless gas from poisoning you, your family or others. • Know the symptoms of carbon monoxide poisoning; headache, dizziness, weakness, nausea, vomiting, sleepiness and confusion. Carbon monoxide reduces the blood’s ability to carry oxygen. Low blood oxygen levels can result in loss of consciousness and death. • See a doctor if you or others develop cold or flu-like symptoms while cooking or in the vicinity of this appliance.
LIGHTING THE HEATER: Initial Lighting Instructions (To be used on initial firing) Push shut-off lever (inside the hopper) down, turn heat adjustment lever to low before filling hopper with pellers. Fill the hopper around ½ full. This one-time initial firing needs to be done to cure the paint on the unit. Put the heat adjustment lever on the LOW setting to limit the number of pellets in the firepot for the entire initial burn period.
PROPER CARE & MAINTENANCE: • • Remove wood pellets from hopper if heater will not be used for a long period of time. Wood pellets can become soggy due to moisture/humidity and clog up the firepot and pellet chute. Disposal of ashes – Ashes should be placed in a metal container with a tight-fitting lid. The closed container of ashes should be placed on a non-combustible floor or on the ground, well away from all combustible materials, pending final disposal.
ASSEMBLY INSTRUCTIONS: Make sure you have all items listed under PARTS LIST and PARTS CARD CONTENTS before you begin the installation process.
READ ALL SAFETY WARNINGS & INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING AND OPERATING YOUR EVEN EMBERS® PELLET HEATER. FOR MISSING PARTS, PLEASE CALL CUSTOMER SERVICE AT 855-735-9922. (Proof of purchase will be required.
1 2 3 5 4 7 6 9 8 10 11 12 13 14 16 15 9
1 Place heater body upside down as illustrated. Install four M6 x 35 mm bolts and two M6 x 12 mm bolts. Heater Body 2 Install four feet.
3 Install chimney collar using four M6 x 12 mm bolts and four M6 nuts. 4 Install lower chimney to chimney collar and fasten in place with two M4 x 10 mm bolts. Install upper chimney to chimney cap and fasten in place with three M6 nuts. Install upper chimney to lower chimney and fasten in place with two M4 x 10 mm bolts.
5 Remove ash cleanout grate handle. Slide ash cleanout grate into firepot and set in place. Center heat baffle over firepot. 1 2 6 Install ash cleanout grate handle through back of heater body.
7 Install heat adjustment lever and lock into place with cotter pin. Install spring coil handle onto heat adjustment lever. 8 Install door latch using one M6 x 16 mm bolt and M6 lock nut.
9 Install ash tray handle using two pre-attached M5 x 12 mm bolts. Insert ash tray into grill body.
WARRANTY The Boltz Group warrants to the original purchaser that the Even Embers® Pellet Fuel Heater is free from defects due to workmanship or materials for One-year. The Boltz Group obligations under this warranty are limited to the following guidelines: • This warranty does not cover heaters that have been altered/modified or damaged due to: normal wear, rust, abuse, improper maintenance and/or improper use.
