VERSES Takeoff contents {en 3 Table of contents % Safety 4 1.1 important safety instructions 4 1.2 Battery and internal charger safety roles 8 1.3 Suspension 7 1.4 FOO information 7 1.5 Precautions & 18 Certifications @ 7 Motives $ 2 Description 11 2% Short information 11 22 System features 12 23 Click setup 132 3 Pairing the Quick Smart Mobile app 15 4 Tripod and floor monitor operation iz 4.1 Tripod or pole mount 17 4.2 Floor monitor & kickback 13 5 Amplifier DSF 23 5.1 Amplifier DSP controls 21 5.
on Safety EVER BE 8 Safety 1.1 important safety instructions The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user fo the WARNING: TO REDUCE THE RISK OF presence of insulated "dangerous FIRE OR ELECTRIC SHOCK, DO NOT voltage” within the product's enclosure OVEREXPOSE THIS APPLIANCE TO RAIN that may be sufficient magnitude to OR MOISTURE constitute a risk of electric shock to VASE: RISQUE DE CHOC ELECTRIC, persons. HE FAS QUIRINAL.
VERSES Safety fan Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, Guided has banes spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. No naked flame sources, such as lighted candies, should be placed on the apparatus.
8 end Safety EVER BE 8 8, Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. Damaged plug and cord may result in electric shock ar fire. 18. Disconnect the VERSE 8 loudspeaker by pulling the plug rather than the cord. Do not operate the VERSE & loudspeaker with damaged cord or plug. Have them replaced immediately. Damaged plug or cord may result in electric shock or fire. 11.
VERSES Safety fan 7 Battery protection mode The lithium-ion battery is protected against deep discharging by the “Battery protection made”. When the battery is employ, the VERSE 8 loudspeaker enters a battery protection mode. The battery is supplied partially charged. Completely charge the battery before using your loudspeaker for the first time. The lithium-lon battery can be charged at any Hume, without reducing its service Fe. Interrupting the charging procedure does not damage the battery.
safety EVER BE 8 ~ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ~ Consult the dealer or an experienced radio/TV/ communications equipment technician. The device has been granted by FOC and IC, the FOC ID-PERSEVERE and 10: PERSEVERANCE Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
en Safety EVER BE 8 Alf content including specifications, date, and illustrations in this manual are subject to change without prior notice. Notice! Bluetooth® is available in select countries. Contact your nearest Electra-Voice dealer or Electra-Voice distributor for more information. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Bosch Security Systems, LLC is under license.
VERSES Description fan 11 2 Zi Description Thank you for choosing an Electromotive powered loudspeaker system. Please take time to consult the manual to understand all the features built into your Electra-Voice system and fully utilize its performance capabilities. The VERSE 8 is a versatile, says to use, compact, battery-powered speaker system. ft provides professional level performance and is housed in a robust weatherized enclosure.
en Description EVER BE 8 2.2 importer and after-sales service China Bosch {Shanghai} Security Systems Ltd. 433 Fugue Road North iBP Changing District Shanghai 200335 P.R. China HE (LE) SELLERS FIR ATH ERA BRIER Eu Bosch Sicherheitssysteme Gm Robert-Bosch-Ring § 85830 Grassland Germany UK Robert Bosch Lid. Broad water Park Mort Orbital Road Bridge UBS SHS ux Mexico Robert Bosch Callie Robert Bosch No. Ext. 408 C.P.
VERSES Description fan 13 audio functions. The Quick Smart Mobile app allows pairing and grouping speakers, in any combination, including VERSE B, ELX200 powered family, and the EVOLVE family. High Quality Stereo Bluetooth® streaming. The VERSE 8 features Bluetooth® streaming using the codex for high quality stereo audio streaming with compatible devices. Two VERSE 8 speakers can be paired for True Wireless Stereo (TWAS] streaming farm a mobile device.
en Description EVER BE Push the input selection soft key to exit the channel menu. Connect an audio source using an XLR or TRS cable fo INPUT 1, INPUT 2, or 2 3.8mm i jack to INPUT 3/4. Push the input selection soft key for INPUT & or INPUT 2 if using LR or TRS cable, or push the input selection soft key for INPUT 344.1 using 3.5mm mint jack. Lie the MASTER VOL knob to adjust gain to the required audio level slowly. Press the input soft key again to exit the channel menu. Adjust the MASTER VOL knob to 0 dB.
VERSES Pairing the Marksman Mobile app fen 15 3 Pairing the Quick Smart Mobile app The BV Quick Smart Mobile app is available for download for the #05 12 and higher tablets and smart phones from the iTunes App Store or Android 8.0 and higher tablets and smart phones from the Google Play Store. Notice! The EV Quick Smart Mobile app is designed to only find speakers from Electra-Voice with Bluetooth® enabled. The EV Quick Smart Mobile app will not display other types of Blustooth® devices, e.g.
en Pairing the Charismatic Mobile app EVER BE 8 ~ Finding nearby speakers is displayed on the screen The EV Quick Smart Mobile app is looking for available Blustooth® enabled Electron-Voice loudspeakers, The available loudspeakers ars displayed on the screen. The app will display up to eight available loudspeakers. Tap the loudspeaker you want to pair with the app. The selected loudspeaker will have a red line under it acknowledging i is selected.
VERSES Tripod awd finer manor preparation {en AF 4 Tripod and floor monitor operation 4.1 Tripod or pole mount VERSE 8 loudspeakers mount on a tripod stand or on z pole above a sub woofer. Mounting a loudspeaker on a tripod tam Caution! Tripod is not evaluated for safety with this loudspeaker. Check the specifications of the tripod stand to be certain it is capable of supporting the weight of the loudspeaker. To rout a loudspeaker on a tripod stand, do the following: 1.
38 en Tripod and Boor monster operation EVER BE & Mounting a loudspeaker on a pole To aunt a loudspeaker on a pole, do the following: 1. Place the sub woofer on a level and stable surface. 2. Insert the M20 threaded pole into the combo pole cup on the top of the sub woofer. 3. Turn the M20 threaded pole clockwise to secure the pole to the sub woofer. 4. Lift the loudspeaker using two hands. &. Set the pole cup located on the bottom of the loudspeaker onto the pole. {1F.
en Tripod and Boor monster operation EVER BE & Notice! Secure cables with wire ties or tape whenever possible.
VERSES Amplifier BSP fan 21 Amplifier DSP Amplifier DSP controls The amplifier has a combination of controls and connectors to ensure the most versatile found speaker system. Full-Range loudspeaker control and monitoring Interface The foll-tangs loudspeaker DSP control menu selections are available for the VERSE 8. Figure 5.4: Full range loudspeaker amplifier panel i. 2. 10. LOD — DSP control and monitoring interface. MASTER VOL Adjusts the sound level and navigates DSP menu.
en Amplifier DSP EVER BE 8 5.2 System status Normal LE i range is from mute increments. INPUT VU meter displays the signal revel of INPUT 1 undo the amplifier from INPUT © connector. The display of P indicates 48 V phantom power is switched on. INPUT YU meter displays the signal level of INPUT 2 inch the amplifier from INPUT 2 connector. The display of H indicates Hi-Z instrument connection is present on the INPUT 2 TRS connection.
VERSES Amplifier DSP LIMIT protects the loudspeaker from short-term peaks which can cause distortion. When LIMIT is shown small on the screen, the limiter is active but keeps distortion under control. The large LIMIT indicates the sound is negatively affected. Reducing the output volume {MASTER VOL) is strongly recommended when the large limit indication is shown. DSP controls An integrated DOP control menu allows the user 1o select multiple DSP system settings on the loudspeaker.
en Amplifier DSP EVER BE 8 531 Full-Range loudspeaker DSP control menu The fool-rangs loudspeaker DSF control menu selections are available for the VERSE BS loudspeakers.
VERSES Amplifier DSP {an 25 RESET ALL HO BYPASS OFF ON PEG # 1 108 TYPE PEL Hi SHELF LOW SHELF Hi PASS LOW PASS a7 05-100 FREQ 120 Hz 20 20.0kHz GAIN GdB “1248 6 6B RESET BACK ENABLE ON OFF AFS OFF ON MD LOUT L+R BLUETOOTH BACK.
2% en Amplifier DSP EVER BE 8 LINK SPEAKERS BACK LED ON {Default) OFF LIMIT DISPLAY BACK LOD Di ON {Default) OFF BRIGHT 3 1-10 CONTRAST 5 1-10 BACK STORE EXIT, 1,2, 8,4, 5, EXIT RECALL EXIT, L, 2,3, 4, 5,6 EXIT RESET RESET ARE YO SURE? NO {Default) YES INFO [PRODUCT NAME] {FIRMWARE VERSION] 2021 Electra-Voice EXIT Tab. 5.1: Full-Sarge Loudspeaker DSP contrived Deena EXIT menu The Exit menu is used 10 return fo the home screen.
VERSES Amplifier BSP an 27 The default is MUSIC. LOCATION menu The Location menu is used to optimize the loudspeaker for different boundaries. Available options for this selection are: TRIPOD, MONITOR, and KICKBACK, — TRIPOD is used when the loudspeaker is placed on a tripod stand or placed on a pole. — MONITOR is sad when the loudspeaker is placed on the angled monitor panel in monitor position.
en Amplifier DSP EVER BE 8 LD DIM menu The LOD Dis menu is used to dim the display when the display is idle for two minutes. Available options for this selection are: ON or OFF. The default is ON. BRIGHT menu The Bright menu is used to determine the brightness of the LCD. The range The default is five. CONTRAST menu The Contrast menu is used to increase or decrease the visibility of the LUD screen. The default is five. STORE menu The Sterne menu allows you create up to five customized user settings.
VERSES Amplifier BSP {on 28 LOCK many The Lock menu is designed to prevent users from inadvertently changing settings. Available options for this selection are: NO or YES. The default is NO. Lacking the DSP menu To dock the DSP menu, do the following: 1. From the DSP menu, scroll to LOCK. 2. Select ON. Notice! i menu dock is ON, the user is allowed to adjust the MASTER VOL. Unlocking the DSP menu To unlock the DSP menu, do the following: ¥ Press and hold the MASTER VOL knob for three seconds.
3% en Amplifier DSP EVER BE 8 Notice! The reset menu item is used to revert the loudspeaker to the original factory default settings. All user settings will be deleted. The user customized settings in the STORE and RECALL menus rectum to EMPTY. INFO menu The information menu is used to display the product name and firmware version. {1F.
VERSES Mb Operation fen 31 Mixer Operation inputs 1,2, 4 3/4 INPUT LEVEL contra The INPUT LEVEL control adjusts the sensitivity of the incoming signals to the internal operation level of the mover. To achieve a good signal input level 1. Set the MASTER volume controls Set the INPUT LEVEL control Connect the sound source (microphone, instrument and 50 on} to the required LINE/MIC input. 4. Start the sound source at the highest volume level to be expected.
en Mixer Operation EVER BE & Phantom power +48 ¥ DC Phantom power is available on the XLR connector of INPUT 4 only. There is no phantom prows on the TRS connectors. Phantom power is switchable, Notice! Switch off Phantom power (default) for devices which do not require phantom power such as dynamic microphones and mixer outputs. COMP control The COMP control controls the onboard compressor to adjust the input signal processing during operation.
VERSES Embosser Operation [en 33 Reducing feedback To reduce feedback: i. Set the speaker and microphone or instrument according fo your performance. Follow appropriate microphone placement and use practices: Do not place the microphone directly in front of the speaker. Refer to the user manual of your microphone to know the pickup and rejection patterns of your microphone.
en Recommended configurations EVER BE & 7 Recommended configurations 7.1 Connecting with mobile device Notice! ©) The direction of the arrow indicates the signal path. Mode: Music Location: Tripod Subs: Off INPUT preset: None Tab. 7.2: DSP settings loudspeaker on 2 triad {1F.
VERSES Recommended configurations [en 35 7.2 Street Musician performance Nat ice! @ The direction of the arrow indicates the signal path. Mode: Live Location: Kickback Sulla: Off INPUT 1 preset: Vocal Mic INPUT 2 preset: Acoustic GTR Tal. 7.
3% en Recommended configurations EVER BE & 7.3 reo (TWS} Sy re Mode: Music Location: Tripod Subs: Off INPUT preset: None Ta. 7.4: DSP settings loudspeaker on a tripod 7.4 Using as monitor LINE and MIC input feel control is available for both INPUT L and INPUT 2. The 12 o'clock position is unity gain {no gain or attenuation} and the range to the right of zero is for adjusting microphone levels. {1F.
VERSES Recommended configurations [en 37 Notice! The direction of the arrow indicates the signal path. Modes Live Location: Monitor Sub: off INPUT 1 preset: Vocal Mic INPUT 2 preset: Bass GTR Tab. 7.
en Recommended configurations EVER BE & 7.5 Using as monitor while recording ELXZ00-15F ELXHO0-1BEF Notice! The direction of the arrow indicates the signal path. Mode: Live Location: Kickback INPUT 4 preset: Low CUT 120 Hz INPUT 2 preset: Electric GTR Tab. 7.6: DSP settings loudspeakers as monitors while retarding {1F.
VERSES Troubleshooting Troubleshooting Problem Possible Causes) Action i. No sound Amplifier Verify all the electronics are on, the signal routing is correct, the source is active; the volume is turned up, ete. Correctfrepair/replace as necessary. If there is still no sound, then the problem may be wiring. Wiring Verify you have connected the correct cables to the amplifier. Play something at a low level through the amplifier. Connect 5 best loudspeaker in parallel with the malfunctioning line.
43 en Troubleshoot ng EVER BE 8 Problem Possible Cause{s} Action Incorrect gain structure or source input {mixing comprehensions) is overdrive Verify level controls of the source are properly structured by using the VU meter indicator on the LOD screen. if the Vi meter bar is solid or the system indicates LIMIT, the input or source level is too high. 7.
VERSES Nonchalant data {en 41 9 Technical data E VERSES-EU 8” 2-way speaker and VERSES-US 8” 2-way speaker Frequency response [8 dB): kHz Frequency range (-10 kHz Wap. SPL 12148 Coverage angle (Hx Vi 100° x 100° Power rating: 200W LF transducer: 8 in. woofer fer rite magnet HF transducer 1 in. titanium dome, neodymium magnet, ferry-fluid cooled Crossover frequency: 2280 Hz Connectors: 2 AXLETREES Combo, 1 3.
