Wireless-G Outdoor PoE AP User’s Manual BEFORE INST ALLING THE UNIT, PLEASE RE AD THIS M ANU AL THOROUGHLY, AND RET AIN IT FOR FUTURE REFERENCE. Copyright 2008 EUSSO Technologies, Inc. All rights reserved.
► Contents Chapter 1. Introduction............................................................................................... 4 1.1 Introducing the UOW2000 Series............................................................ 4 1.2 Product Features ....................................................................................... 4 1.3 Package Contents ...................................................................................... 4 1.4 System Requirements ....................................
6.1.1 WIZARD ........................................................................................ 56 6.1.2 LAN .................................................................................................. 57 6.1.3 DHCP............................................................................................... 57 6.1.4 WIRELESS.................................................................................... 58 6.2 ADVANCE ........................................................................
Chapter 1. 1.1 Introduction Introducing the UOW2000 Series The UOW2000 Series is fully interoperable with IEEE 802.11a and/or 802.11b/g compliant Outdoor Wireless Last-mile product. The UOW2000 SERIES operates in AP mode or remote bridge mode, and connects to UOW2000 SERIES AP/CB to construct point-to-point as well as point-to-multipoint topologies, for maximum flexibility in configuring building-to-building networks and WISP functions. 1.
1.4 System Requirements Installation of the UOW2000 Series Outdoor Wireless Access Point/Client Bridge requires the following: 1. A Windows-based PC/AT compatible computer （ PC system requirement：better than PIII 800 or other 100% compatible equipment , OS： windows 2000/XP ） or Ethernet data device with an available RJ-45 Ethernet port to run the configuration program or with TCP/IP connection to the Ethernet network. 2. A 10/100Base-T Ethernet RJ-45 Ethernet cable is connected to Ethernet network. 3.
Chapter 2. Installation and Basic Configuration This chapter describes the procedures of installing the UOW2000 Series. 2.1 Before You Start After unpacking the system, make sure the following items are present and in good condition. Refer to below pictures for product image. 1. UOW2000 Series Outdoor Wireless Access Point/Client Bridge unit 2. 100~240VAC, 50~60Hz AC to 48V/0.375A DC switching adapter 3. Inline Power Injector (PoE) 48VDC, 0.375A 4. RJ-45 CAT-5 Ethernet cable 30 m 5.
2.2 Locate the UOW2000 Series and Inline Power Injector Ports ► Interface on the UOW2000 Series Unit ¾ Ethernet Port 1 : for connecting the 30m RJ-45 CAT-5 Ethernet cable. ► Interface on the Inline Power Injector ¾ Data Input Port 2 : for connecting cross-over Ethernet Cable to PC or straight Ethernet cable to Hub Switch Router . ¾ DC Input Port 3 : power adapter 48V, 0.375A DC input. ¾ Power & Data Output Port 4 : for connecting the 30m RJ-45 CAT-5 Ethernet Cable.
► Mount UOW2000 Series on A Wall/Mast The UOW2000 Series can be mounted on the wall, you can use the Wall Mount kit to mount the UOW2000 Series as shown in Figure 2-2. Figure 2-2 You can also mount the UOW2000 Series to the mast as shown in Figure 2-3.
2.3 Preparing Installation Before installing UOW2000 Series for outdoor application or hard-to-reach location, we recommend configuring and test all the devices first. For configuring the UOW2000 Series, please follow the quick steps below to power up the UOW2000 Series. Refer to Figure 2-4 for steps 1 through 5. Figure 2-4 Step1 : Connect the DC plug of the AC/DC power adapter into the DC Input Port of Inline Power Injector and the wall-mount plug into a power outlet or power strip (refer to page 6).
2.4 2.4.1 Basic Configuration Basic Configuration Steps This section describes a two-step BASIC configuration procedure to setup UOW2000 Series. Step1 : Modify the factory-default parameters on the web page “/BASIC/LAN/”, and click Save Settings to save the changes, than click Continue . Step2 : Modify the factory-default parameters on the web page “/BASIC/Wireless/”, and click Save Settings to save the changes, than click Reboot the Device to take effect on the previous configuration changes. 2.4.
Figure 2-5 Step3 : Enter “admin” in the Password fields, and click Log In to enter the web configuration user interface screen as shown below. Figure 2-6 ► Web Configuration Structure The web configuration user interface shown above in Figure 2-6 is grouped into a tree structure, and contains the following settings or information.
▽ BASIC ● WIZARD ● LAN ● DHCP ● WIRELESS ▽ ADVANCED ● MAC ADDRESS FILTER ● ADVANCED WIRELESS ▽ TOOLS ● ADMIN ● TIME ● SYSTEM ● FIRMWARE ▽ STATUS ● DEVICE INFO ● WIRELESS ● LOGS ● STATISTICS ▽ HELP ● MENU ● BASIC ● ADVANCED ● TOOLS ● STATUS ● GLOSSARY Move through the tree by clicking on an icon to expand or collapse the tree. The nodes on the tree represent web pages that allow viewing and modifying the parameters.
2.4.3 Set Operating Mode, IP Address, Subnet Mask, Default Route IP, DNS Server IP of UOW2000 SERIES ► LAN Settings These are the settings of the LAN (Local Area Network) interface for the Access Point. The Access Point's local network (LAN) settings are configured based on the IP Address and Subnet Mask assigned in this section. The IP address is also used to access this Web-based management interface. This option is available in the “/BASIC/LAN/” page as shown in Figure 2-7.
The IP address of the AP on the local area network. Assign any unused IP address in the range of IP addresses available for the LAN. For example, 192.168.0.1. ► Subnet Mask The subnet mask of the local area network. ► Gateway The IP address of the router on the local area network. ► Local Domain Name This entry is optional. Enter a domain name for the local network. The AP's DHCP server will give this domain name to the computers on the wireless LAN. So, for example, if you enter mynetwork.
2.4.4 Set Wireless SSID for Wireless Interface ► Wireless Network Name （Also called the SSID） When you are browsing for available wireless networks, this is the name that will appear in the list (unless Visibility Status is set to Invisible, see below). This name is also referred to as the SSID. For security purposes, it is highly recommended to change from the pre-configured network name.
2.4.5 Set Wireless Encryption for Wireless Interface The UOW2000 Series supports 64-bit and 128-bit WEP encryption. For 64-bit WEP encryption, an encryption key is 10 hexadecimal characters (0-9 and A-F) or 5 ASCII characters. For 128-bit WEP encryption, an encryption key is 26 hexadecimal characters or 13 ASCII characters. Modify the WEP encryption parameters on the web page “/BASIC/WIRELESS/WIRELESS SECURITY MODE”.
2.4.6 Change Supervisor Account & Password Enter the TOOLS > ADMIN page. Figure 2-9 below shows the TOOLS/ ADMIN page. Figure 2-9 ► ADMIN PASSWORD Change the ADMIN PASSWORD’s user name and password in the ADMIN PASSWORD Account field, and click Save Setting ，than Reboot the Device. to take effect on the previous configuration changes.
2.4.7 ► Upgrade the Firmware Update the Firmware Enter the TOOLS > FIRMWARE page as shown in Figure 2-10 to upgrade UOW2000 Series. Here, user must select which file you want to upgrade it (Program image), then click Upload button to start the upgrade process. Hint: It takes about 1 min, to complete the restart process. Figure 2-10 Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using integrated antennas.
Chapter 3. Network Topologies This chapter describes several common types of installations implemented by using the UOW2000 Series’s line of Outdoor Wireless System. This is by no means intended to be an exhaustive list of all possible configurations, but rather shows examples of some of the more common implementations. The UOW2000 Series CB can be configured to function as a Wireless Client Router or Bridge to a central access point like the UOW2000 Series AP see Figure 3-1 below.
3.1 Wireless Client Bridge-to-Central Wireless Bridge Figure 3-2 Refer to Figure 3-2 for the following setup. Note: The UOW2000 Series AP is the Central Wireless Bridge and UOW2000 Series CB is the Wireless Client Bridge Step 1 Set the UOW2000 Series AP to perform a bridge (bridge IP address: 192.168.1.1). Step 2 Set Wireless parameters on the AP11 to: Channel (1) and SSID (wireless) Step 3 Set the UOW2000 Series CB to function in the bridge mode (bridge IP address: 192.168.1.241).
Chapter 4. 4.1 4.1.1 All function on Device BASIC Wizard This wizard guides you through the following basic Access Point setup steps: Set your Password Select your Time Zone Configure your Wireless Connection WCN Wizard If your PC's operating system is Windows XP Service Pack 2 (SP2) or later and you are using Windows Internet Explorer (IE) as your browser, you can use Windows Connect Now (WCN) technology to help configure the Access Point's wireless security settings.
Note that WCN only sets a few of the wireless options. You will still need to go to the Home -> Wireless page to set other wireless options such as Super G Mode and transmission rate.
4.1.2 LAN These are the settings of the LAN (Local Area Network) interface for the Access Point. The Access Point's local network (LAN) settings are configured based on the IP Address and Subnet Mask assigned in this section. The IP address is also used to access this Web-based management interface. Figure 4-2 Get LAN IP From Choose "DHCP (Dynamic)" if your router supports DHCP and you want the router to assign an IP address to the AP. In this case, you do not need to fill in the following fields.
IP Address The IP address of the AP on the local area network. Assign any unused IP address in the range of IP addresses available for the LAN. For example, 192.168.1.101. Subnet Mask The subnet mask of the local area network. Gateway The IP address of the router on the local area network. Local Domain Name This entry is optional. Enter a domain name for the local network. The AP's DHCP server will give this domain name to the computers on the wireless LAN. So, for example, if you enter mynetwork.
4.1.3 DHCP DHCP stands for Dynamic Host Configuration Protocol. The DHCP section is where you configure the built-in DHCP Server to assign IP addresses to the computers and other devices on your local area network (LAN).
In most situations, the router provides DHCP services, and you can leave this option disabled. However, if for any reason the router does not provide DHCP services, enable this option. The AP's DHCP Server will then manage the IP addresses and other network configuration information for wireless clients associated with the AP. The computers (and other devices) connected to your LAN also need to have their TCP/IP configuration set to "DHCP" or "Obtain an IP address automatically".
manually configured. Suppose you have a web server computer that has a manually configured address of 192.168.1.100. Because this falls within the "managed range" be sure to create a reservation for this address and match it to the relevant computer (see Static DHCP Client below). DHCP Lease Time The amount of time that a computer may have an IP address before it is required to renew the lease. The lease functions just as a lease on an apartment would.
Reservations are helpful for server computers on the local network that are hosting applications such as Web and FTP. Servers on your network should either use a static IP address or use this option. MAC Address: To input the MAC address of your system, enter it in manually or connect to the Access Point's Web-Management interface from the system and click the Copy Your PC's MAC Address button. A MAC address is usually located on a sticker on the bottom of a network device.
deleted by clicking the Delete icon. When you click the Edit icon, the item is highlighted, and the "Edit DHCP Reservation" section is activated for editing.
4.1.4 WIRELESS The wireless section is used to configure the wireless settings for your Access Point. Please note that changes made on this section may also need to be duplicated on your Wireless Client. To protect your privacy, use the wireless security mode to configure the wireless security features. This device supports three wireless security modes including: WEP, WPA-Personal, and WPA-Enterprise. WEP is the original wireless encryption standard. WPA provides a higher level of security.
This option turns off and on the wireless connection feature of the Access Point. When you set this option, the following parameters are displayed. Wireless Network Name When you are browsing for available wireless networks, this is the name that will appear in the list (unless Visibility Status is set to Invisible, see below). This name is also referred to as the SSID. For security purposes, it is highly recommended to change from the pre-configured network name.
By default the fastest possible transmission rate will be selected. You have the option of selecting the speed if necessary. 802.11 Mode If all of the wireless devices you want to connect with this Access Point can connect in 802.11g mode, you can improve performance slightly by changing the mode to 802.11g only. If you have some devices that are 802.11b, leave the setting at Mixed. Super G™ Mode Super G without Turbo: Performance enhancing features such as Packet Bursting, FastFrames, and Compression.
Both of these options select some variant of Wi-Fi Protected Access (WPA) -- security standards published by the Wi-Fi Alliance. The WPA Mode further refines the variant that the Access Point should employ. WPA Mode: WPA is the older standard; select this option if the clients that will be used with the Access Point only support the older standard. WPA2 is the newer implementation of the stronger IEEE 802.11i security standard.
Authentication Timeout: Amount of time before a client will be required to re-authenticate. RADIUS Server IP Address: The IP address of the authentication server. RADIUS Server Port: The port number used to connect to the authentication server. RADIUS Server Shared Secret: A pass-phrase that must match with the authentication server. MAC Address Authentication: If this is selected, the user must connect from the same computer whenever logging into the wireless network.
4.2 4.2.1 ADVANCED MAC Address Filter The MAC address filter section can be used to filter network access by machines based on the unique MAC addresses of their network adapter(s). It is most useful to prevent unauthorized wireless devices from connecting to your network. A MAC address is a unique ID assigned by the manufacturer of the network adapter. Figure 4-5 Enable MAC Address Filter When this is enabled, computers are granted or denied network access depending on the mode of the filter.
Filter Settings Mode When "only allow listed machines" is selected, only computers with MAC addresses listed in the MAC Address List are granted network access. When "only deny listed machines" is selected, any computer with a MAC address listed in the MAC Address List is refused access to the network. Filter Wireless Clients When this is selected, the MAC address filters will be applied to wireless network clients.
4.2.2 Advance Wireless Figure 4-6 Fragmentation Threshold This setting should remain at its default value of 2346. Setting the Fragmentation value too low may result in poor performance. RTS Threshold This setting should remain at its default value of 2346. If you encounter inconsistent data flow, only minor modifications to the value are recommended. Beacon Period Beacons are packets sent by a wireless Access Point to synchronize wireless devices. Specify a Beacon Period value between 20 and 1000.
Access Point has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. Wireless clients detect the beacons and awaken to receive the broadcast and multicast messages. The default value is 1. Valid settings are between 1 and 255. 802.11d Enable Enables 802.11d operation. 802.11d is a wireless specification for operation in additional regulatory domains. This supplement to the 802.
4.3 4.3.1 TOOLS Admin The Admin option is used to set a password for access to the Web-based management. By default there is no password configured. It is highly recommended that you create a password to keep your new Access Point secure.
Figure 4-7 Admin Password Enter a password for the user "admin", who will have full access to the Web-based management interface. User Password Enter a password for the user "user", who will have read-only access to the Web-based management interface. Access Point Name The name of the Access Point can be changed here. Admin Idle Timeout The amount of time before the administration session (either remote or local) is closed when there is no activity.
Note that WCN only saves a few of the wireless security settings. When you use WCN to propagate settings to other wireless devices, you may have to make additional settings manually on those devices. Note that, in Microsoft's current implementation of WCN, you cannot save the wireless settings if a profile of the same name already exists.
4.3.2 Time The Time Configuration option allows you to configure, update, and maintain the correct time on the Access Point's internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight saving can also be configured to automatically adjust the time when needed.
Time Configuration Time Zone Select your local time zone from pull down menu. Daylight Saving Enable Check this option if your location observes daylight saving time. Daylight Saving Offset Select the time offset, if your location observes daylight saving time. DST Start and DST End Select the starting and ending times for the change to and from daylight saving time. For example, suppose for DST Start you select Month="Oct", Week="3rd", Day="Sun" and Time="2am".
4.3.3 System This section allows you to reboot the device, and restore the Access Point to the factory default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you've created. Figure 4-9 Reboot the Device This restarts the Access Point. Useful for restarting when you are not near the device.
4.3.4 Firmware The Firmware Upgrade section can be used to update to the latest firmware code to improve functionality and performance. Figure 4-10 To upgrade the firmware, follow these steps: 1. Click the Browse button to locate the upgrade file on your computer.
2. Once you have found the file to be used, click the Upload button below to start the firmware upgrade process. This can take a minute or more. 3. Wait for the Access Point to reboot. This can take another minute or more. 4. Confirm updated firmware revision on status page. Firmware Information Here are displayed the version numbers of the firmware currently installed in your Access Point and the most recent upgrade that is available.
4.4 4.4.1 Status Device Info All of your Internet and network connection details are displayed on the Device Info page. The firmware version is also displayed here. Note: Some browsers have limitations that make it impossible to update the WAN status display when the status changes. Some browsers require that you refresh the display to obtain updated status. Some browsers report an error condition when trying to obtain WAN status.
LAN Computers This area of the screen continually updates to show all DHCP enabled computers and devices connected to the LAN side of your Access Point. The detection "range" is limited to the address range as configured in DHCP Server. Computers that have an address outside of this range will not show. If the DHCP Client (i.e. a computer configured to "Automatically obtain an address") supplies a Host Name then that will also be shown.
4.4.2 Logs The Access Point automatically logs (records) events of possible interest in its internal memory. If there is not enough internal memory for all events, logs of older events are deleted, but logs of the latest events are retained. The Logs option allows you to view the Access Point logs. You can define what types of events you want to view and the level of events to view.
What to View Select the kinds of events that you want to view. • System View Levels Select the level of events that you want to view. • • • Critical Warning Informational Apply Log Settings Now Click this button after changing Log Options to make them effective and permanent. Refresh Clicking this button refreshes the display of log entries. There may be new events since the last time you accessed the log. Clear Clicking this button erases all log entries.
4.4.3 Statistics The Statistics page displays all of the LAN, WAN, and Wireless packet transmit and receive statistics. Figure 4-13 Sent The number of packets sent from the Access Point. Received The number of packets received by the Access Point. TX Packets Dropped The number of packets that were dropped while being sent, due to errors, collisions, or Access Point resource limitations.
The number of packets that were dropped while being received, due to errors, collisions, or Access Point resource limitations. Collisions The number of packets that were dropped due to Ethernet collisions (two or more devices attempting to use an Ethernet circuit at the same time). Errors The number of transmission failures that cause loss of a packet. A noisy radio-frequency environment can cause a high error rate on the wireless LAN.
Chapter 5. Specifications The UOW2000-Series Outdoor Wireless Multi-Client Bridge/Access Point/WDS (wireless distribution system) operates seamlessly in the 2.4 GHz frequency supporting the IEEE 802.11b/802.11g wireless standards. It's the best way to add wireless capability to your existing wired network, or to add bandwidth to your existing wireless installation.
Features z z z z z z z z High Speed Data Rate Up to 54Mbps Output Power up to 17 dBm (23dBm, 26dBm optional requirement) IEEE 802.11b/g Compliant Point-to-point, Point-to-multipoint Wireless Connectivity WEP/WPA/WPA2/ IEEE 802.1x Authenticator support WDS (Wireless Distribution System) Dust tight and Watertight and Weatherproof (IP67/IP68) Wide temperature range and robust mechanical design z Power-over-Ethernet (IEEE802.3af Compliant) Technical Specifications Data Rates 1, 2, 5.
Antenna 5dBi External RF Connector SMA Type (AP only) Networking Topology Ad-Hoc, Infrastructure Operation Mode Point-to-Point/ Point-to-Multipoint Bridge/ AP/ Client Bridge/ WDS Interface One 10/100Mbps RJ-45 LAN Port Security IEEE802.
Chapter 6. 6.1 Default Settings BASIC 6.1.1 WIZARD 6.1.1.1 CONNECTION SETUP WIZARD Parameter Description Password Web Login password Default Value admin Verify Password Time admin GTM-08:00,Tijuana Time Zone 6.1.1.2 MICRPSOFT WINDOWS CONNECT WIZARD 6.1.1.
6.1.2 LAN Parameter Description Default Value Get LAN IP from A name it can be easily recognized by wireless clients Static IP(Manual) IP Address In order to protect your network from hackers and unauthorized users 192.168.1.1 Subnet Mask 255.255.255.0 Gateway 0.0.0.0 Local Domain Name NULL 6.1.3 DHCP 6.1.3.1 ENABLE Parameter Description Enable DHCP Server Default Value Select 6.1.3.2 DHCP SETTING Parameter Description Default Value 192.168.1.100 DHCP IP Address Range ~ 192.168.1.
6.1.3.3 ADD DHCP RESERVATION Parameter Enable Description Enable DHCP RESERVATION Default Value Select IP Address 0.0.0.0 MAC Address 00:00:00:00:00:00 Copy Your PC’s MAC If you press this icon your Address PC’s MAC will show on table Computer Name 6.1.4 NULL WIRELESS 6.1.4.1 ENABLE Parameter Description Enable DHCP Server Default Value Select 6.1.4.
6.2 ADVANCE 6.2.1 MAC Address Filter Parameter Description Enable MAC Address Filter 6.2.2 Default Value No Select Advanced Wireless Parameter Description Default Value Fragmentation Threshold 2346 RTS 2346 Beacon Period 100 DTIM Interval 1 802.11d No Select Transmit Power High WDS Enable No Select 6.3 TOOLS 6.3.1 ADMIN 6.3.1.1 ADMIN PASSWORD Parameter Password Description Web Login password Default Value admin Verify Password admin 6.3.1.
6.3.1.4 SAVE CONFIGURATION TO WIRELESS NETWORK SETUP WIZARD 6.3.2 TIME 6.3.2.1 TIME CONFIGURATION Parameter Description Time Zone Default Value GTM-08:00,Tijuana 6.3.2.2 SET THE DATE AND TIME MANUALLY Parameter 6.3.3 Description Default Value Year 2004 Month Jan Day 31 Hour 1 Minute 7 Second 45 A.M. / P.M. PM SYSTEM Parameter Description Default Value Description Default Value Reboot the Device Restore all Setting to the Factory Defaults 6.3.
Chapter 7. Regulatory Compliance Information 15.21 CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Prohibition of co-location This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 15.
Caution Statement of the FCC Radio Frequency Exposure This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65C and found compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247(b)(4) addressing RF Exposure from radio frequency devices. The radiation output power of this Wireless LAN device is far below the FCC radio frequency exposure limits.
MPE Statement (Safety Information) Your device contains a low power transmitter. When device is transmitted it sends out Radio Frequency (RF) signal. Safety Information CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Use on the supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations.
