Product specifications

ManualsBrandsEusso ManualsComputer equipment5-Port

FCC Warning

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limitations are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if no installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation.

Changes or modifications to the equipment that are not approved by the party

responsible for compliance could affect the user’s authority to operate the

equipment.

CE Declaration of conformity

This equipment complies with the requirements relating to electromagnetic

compatibility, EN 55022 class B for ITE, the essential protection requirements

of Council Directive 89/336/EEC on the approximation of the laws of the

Member States relating to electromagnetic compatibility.

Trademarks:

All trade names and trademarks are the properties of their respective

companies.

Document Version: 2.0

Summary of content (15 pages)

PAGE 1
FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limitations are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if no installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 2
Table of Contents 1. Unpacking Information 2. Introduction To Ethernet over VDSL Converter 2.1 2.2 2.3 2.3.1 2.3.1.1 2.3.1.2 2.3.1.3 2.3.1.4 2.3.1.5 2.3.1.6 2.3.1.7 2.3.2 2.4 2.4.1 3. Installing And Using Ethernet over VDSL Converter 3.1 3.1.1 3.1.2 3.1.2.1 4.
PAGE 3
1. Unpacking Information Thank you for purchasing the Ethernet over VDSL converter. Before you start, please check all the contents of this package. The product package should include the following: 1. 2. 3. 4.
PAGE 4
2. Introduction To Ethernet over VDSL Converter 2.1 General Description The converter is a switching architecture with one RJ-45 10/100Mbps Ethernet port and one maximum 17Mbps symmetric/asymmetric RJ-11 Ethernet over VDSL port (with 2 connectors). It is ideal for signal conversion by transmitting the Ethernet data from the standard twisted pair cable to the telephone cable and extending the distance.
PAGE 5
people do not need to access the services through Internet but using local area network with better bandwidth and efficiency. Meanwhile, this kind of infrastructure will minimize the burden on the Internet. The converter is plug-n-play without any software to configure and also fully compliant with all kinds of network protocols. Moreover, the rich diagnostic LEDs on the front-panel provide the operating status of individual port and the whole system.
PAGE 6
2.2 Key Features The converter provides the following key features: • Complies with IEEE802.3 10BASE-T standard • Complies with IEEE802.3u 100BASE-TX standard • Supports Ethernet over VDSL • 5 * selective transmission modes • 2 * RJ-11 connectors for maximum 17Mbps symmetric/asymmetric Ethernet over VDSL port, one for LAN connection and one for voice connection.
PAGE 7
2.3 The Front Panel The front panel of the converter is shown below. Master Slave 2.3.1 LEDs definition The rich diagnostic LEDs on the front panel can provide the operating status of individual port and whole system. 2.3.1.1 Status LED (Master) The LED blinks periodically to show the ADSL Router is working normally. If the LED stays green/dark that means the system is fail, you need to contact your agent or try to reboot the system. 2.3.1.
PAGE 8
2.3.1.3 100M LED (Ethernet) The RJ-45 port has a 100M LED. Steady green indicates that the port is operating at 100Mbps. If the LED is off, the link speed is 10Mbps. 2.3.1.4 LINK/ACT LED (Ethernet) The RJ-45 port has a LNK/ACT LED. Steady green (link state) indicates that the port has good linkage to its associated device. Flashing green indicates that the port is receiving or transmitting data from/to its associated partner.
PAGE 9
LINK/ACT LED (Ethernet) Status Off No Connection Green 10/100Mbps 2.3.1.5 FDX/COL LED (Ethernet) A collision occurs when two stations within a collision domain attempt to transmit data at the same time. Intermittent flashing amber of the collision LED is normal; the contending adapters resolve each collision by means of a wait-then-retransmit algorithm. Frequency of collisions is an indicator of heavy traffic on the network.
PAGE 10
2.3.1.6 LINK LED (VDSL) If both ends of the VDSL devices are connected then the LED will blink for a while (in 10 seconds), this is the stage of speed auto-negotiation. After the negotiation process, the Link LED will stay green. If the LED blinks always, that means the link process is fail. 2.3.1.7 ACT LED (VDSL) If there is any traffic transverses the port then the LED will light green. Otherwise, off means no traffic on the network. 2.3.
PAGE 11
Transmission mode ANSI ETSI VE-5 VE-10 (Default) VE-15 2.4 DIP switch ON 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 ON ON ON ON The Rear Panel The rear panel of the converter is shown below 2.4.1 Power Connecting Plug the circle end of the power adapter firmly into the rear panel of the switch, and the other end into an electric service outlet then the system is ready.
PAGE 12
3. Installing And Using Ethernet over VDSL Converter 3.1 Installing The Ethernet over VDSL Converter The converter does not require any software configuration. Users can immediately use any feature of this product simply by attaching the cables and plug power on. There is some key limitation on the Ethernet over VDSL networking, please check the following items: The device is used for point-to-point connection only and allows data and voice work on the same telephone lines.
PAGE 13
3.1.1 Connect to Internet Access Concentrator In order to build up a local Internet in apartment, hotel, campus and hospitality environment, the Internet Access Concentrators need to be placed in the wiring center (MDF room) and connect to the telephone line system. On the other hand, you need to install a converter on the individual client side and connect to the Concentrator through the telephone lines.
PAGE 14
3.1.2.1 Station Connections with Telephone Wires Connect the network adapters in stations to the converter’s RJ-45 port through category 3, 4 or 5 UTP/STP cables. There are two RJ-11 phone jacks; one for telephone set connection and the other one is used for phoneline network connection. If you have telephone wall jacks at home then all you need to do is connecting the RJ-11 network port to the wall jack through telephone wires.
PAGE 15
4. Product Specifications Standard IEEE802.3 10BASE-T IEEE802.