ENG User Guide Temperature/Process indicator and alarm unit 2116i/2132i
2132i and 2116i Temperature and Process Indicator and Alarm Units Installing and Operating Instructions Thank you for choosing the 2132i or 2116i indicator and alarm unit. It will provide accurate measurement and display of temperature and other process variables with up to two alarm outputs for operator alert and process protection. Models 2132i/ND and 2116i/ND are Indicator only units which come without the alarm relay output or logic I/O fitted.
OPERATION TO VIEW THE DISPLAY UNITS Switch on the indicator. Following a 3 second self-test sequence, you will see the display shown below. It is called the HOME display. Press and release quickly the units will be flashed for 0.5sec Output 1 Output 2 OP1 OP2 20 0.5 sec The process value (PV)* C 20 ALARM INDICATION or If you get lost, pressing and together will return you to the HOME display.
PARAMETER LISTS HIDE PARAMETERS OR MAKE THEM READ-ONLY Use these lists to change: • Alarm setpoints • Alarm setpoint limits • User calibration HOME List 20 X2 Alarm List Setpoint List AL SP Input List Access List ip ACCS Press Heading. Press 1--- Sp L FiLt CodE 2--- SP H CJC* Goto mV 3FSL HY pass PASS will be displayed when the correct password has been entered. Selecting and adjusting a parameter Use or to select Edit level. Other options are: Press edit got OFS CAL.P OFS.
CONFIGURING THE INDICATOR Linear input scaling (-12.00 to +80.00mV) Select configuration level to change: • Display units • Input sensor type • Scaling of linear inputs • Alarm configuration • Passwords. InP.L mV input low InP.H mV input high VaL.L Displayed value low VAL.H Displayed value high VAL.H VAL.L accs Press Alarm Configuration The AL list configures the three internal ‘soft’ alarms and causes the appropriate alarm message to be flashed in the HOME display.
ORDERING CODE The indicator is supplied configured to the ordering code shown below. 1 2 3 4 5 1. Model Number 2132i 1/8 DIN indicator 2116i ¼ DIN indicator 2. Function ND Indicator only* AL Indicating alarm unit 3. Supply voltage VH 85-264Vac VL 20 -29V dc or ac 4. Manual XXX None ENG English FRA French GER German NED Dutch SPA Spanish SWE Swedish ITA Italian 5.
SAFETY AND EMC INFORMATION INSTALLATION SAFETY REQUIREMENTS This indicator is intended for industrial temperature and process applications when it will meet the requirements of the European Directives on Safety and EMC. Use in other applications, or failure to observe the installation instructions of this handbook may impair safety or EMC. The installer must ensure the safety and EMC of any particular installation. Safety Symbols Various symbols may be used on the indicator.
Over-temperature protection Voltage rating When designing any control system it is essential to consider what will happen if any part of the system should fail. In temperature control applications the primary danger is that the heating will remain constantly on. Apart from spoiling the product, this could damage any process machinery being controlled, or even cause a fire.
ROHS Restriction of Hazardous Substances (RoHS) Product group 2100 Table listing restricted substances Chinese 限制使用材料一览表 产品 2100 铅 X O X X 印刷线路板组件 附属物 显示器 模块 汞 O O O O 镉 X O O X 有毒有害物质或元素 六价铬 O O O O 多溴联苯 O O O O 多溴二苯醚 O O O O O 表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006 标准规定的限量要求以下。 X 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006 标准规定的限量要求。 English Restricted Materials Table Product 2100 PCBA Enclosure Display Modules Pb X O X X Hg O O O O Toxic and hazardous substances and elements Cd Cr(V
International Sales and Service AUSTRALIA Sydney Eurotherm Pty. Ltd. Telephone (+61 2) 9838 0099 Fax (+61 2) 9838 9288 E-mail info.au@eurotherm.com HONG KONG & CHINA Eurotherm Limited North Point Telephone (+85 2) 28733826 Fax (+85 2) 28700148 E-mail info.hk@eurotherm.com AUSTRIA Vienna Eurotherm GmbH Telephone (+43 1) 798 7601 Fax (+43 1) 798 7605 E-mail info.at@eurotherm.com Guangzhou Office Telephone (+86 20) 8755 5099 Fax (+86 20) 8755 5831 E-mail info.cn@eurotherm.
