Owner`s manual

25
LIQUID CRYSTAL DISPLAY (LCD)
Continually provides feedback on the operating status of the hot tub.
Icons indicate various functions and programming information.
LCD INVERT
This feature inverts the LCD readout for convenient viewing from inside
the hot tub. To invert the readout,
Platinum Series: press or then
Titanium Series: press
To return the LCD readout to normal viewing (from outside of the hot
tub), repeat.
TOPSIDE PANEL LOCK FEATURES
TEMPERATURE LOCK
The temperature lock feature prevents unauthorized
temperature adjustment of the hot tub water. When the temperature
lock is activated, all automatic functions will continue to operate
normally.
The following pads must be pressed within 3 seconds of each other to
activate the lock:
then then P1 then
TEMPERATURE UNLOCK
The following pads must be pressed within 3 seconds of each other to
deactivate the lock:
then then P1 then
When locked, the TL (Temperature Lock) light on the left side of the
topside control panel will illuminate. Only the topside control panel
temperature pads will be deactivated.
TOPSIDE PANEL FULL LOCK
The topside panel lock feature prevents unauthorized use of the hot
tub controls. When the topside control panel lock is activated, all
automatic functions will continue to operate normally.
The following pads must be pressed within 3 seconds of each other to
activate the lock:
then P1 then
TOPSIDE PANEL UNLOCK
The following pads must be pressed within 3 seconds of each other
to deactivate the lock:
then P1 then
When locked, the PL light (Panel Lock) on the left side
of the topside control panel will illuminate. All of the topside
control panel pads will be deactivated except for the pad.
STANDBY / DRAIN ASSIST
The standby/drain assist feature stops the system from
operating automatically, allowing for convenient filter cartridge
removal and for safe draining of the hot tub. The following pads
must be pressed within 3 seconds of each other.
The system will automatically exit Standy Mode after 1 hour and
resume normal operating functions.
Press then the P2 pad and the display will flash:
If the system is heating when Standby Mode is activated,
will flash on the display and the pump will continue to operate for
15 seconds to allow the heater to cool off before stopping.
All functions will turn off, but P1 low speed can be
activated (by pressing the P1 pad) to facilitate draining
the hot tub and the display will show
Press any pad other than the P1 pad to return the system to
normal operation. See section DRAINING YOUR HOT TUB for detailed
instructions.
LED MOOD LIGHTING
Press the pad on the topside control to start the
selection of LED lighting modes. Pressing the pad
on/off within 3 seconds cycles through the various ‘light
shows’. When the LED lighting is turned off for more than 5
seconds, then turned back on, the system will resume the last ‘light
show’. The system will automatically turn off the mood lighting after
4 hours.
OZONATOR OPTIONAL
The ozonator operates during FILTER CYCLES and CLEAN UP CYCLES
only. The display will show the O3 icon while the ozonator is operating.
Pressing any pad on the topside control panel will suspend ozonator
function for 1 hour.
FREEZE PROTECTION
If the temperature sensor detects a drop to 4˚C (39˚F)
within the heater chamber, the system automatically activates
the pumps to provide freeze protection. The pumps will
operate until the temperature reaches 5˚C (41˚F) before returning to
normal system mode.
VARIABLE AIR THERAPY SYSTEM (VATS) - Factory installed
Press this pad to turn the (VATS) on and off. The system will
automatically turn off the blower after 15 minutes.
VARIABLE SPEED BLOWER CONTROL FUNCTIONS:
1) ON/OFF :
Press 1: The Blower starts at maximum Speed. LED: ON
Press 2: The blower stops. LED: OFF
2) TO CONTROL SPEED:
Press 1 and hold: Speed goes up or down, LED: ON when
pressing. Release pressure at the desired speed.
3) TO CONTROL PULSATION:
Press 1: Slow Pulsation Cycle, LED: ON.
Press 2: Quick Pulsation Cycle, LED: Flashes.
Press 3: Pulsation Cycle OFF, LED: OFF.
1
3
2
or
or