WM5 Washing Machine
Safety instructions 1 Warnings General Safety • Never place your machine on a carpet covered floor. Otherwise, lack of airflow from below of your machine may cause electrical parts to overheat. This may cause problems with your washing machine. • If the power cable or mains plug is damaged you must call Authorized Service for repair. • Fit the drain hose into the discharge housing securely to prevent any water leakage and to allow machine to take in and discharge water as required.
2 Installation Removing packaging reinforcement Tilt the machine to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon. Opening the transportation locks A Transportation safety bolts must be removed before operating the washing machine! Otherwise, the machine will be damaged! 1. Loosen all the bolts with a spanner until they rotate freely (“C”) 2. Remove transportation safety bolts by turning them gently. 3.
Electrical connection Connect the machine to an earthed outlet protected by a fuse of suitable capacity. Important: • Connection should comply with national regulations. • The voltage and the allowed fuse protection are specified in the section “Technical Specifications”. • The specified voltage must be equal to your mains voltage. • Connection via extension cords or multiplugs should not be made. B A damaged power cable must be replaced by a qualified electrician.
4 Selecting a Program and Operating Your Machine Control panel Figure 1 1 2 1 2 3 4 - 7 3 5 4 6 Spin Speed Adjustment Button Time Delaying Button (+/-) Temperature Adjustment Button Start/Pause/Cancel Button 5 6 7 8 - 8 Auxiliary Function Keys Program Selection Knob Display On/Off Button Display symbols 7.a 7.b 7.c 7.d 7.e - Spin Speed Indicator Temperature Indicator Spin Symbol Temperature Symbol Remaining Time and Delaying Time Indicator 7.
• Cotton You can wash normally soiled durable cotton clothes with this program. Your laundry will be washed with vigorous washing movements during a longer washing cycle. • Synthetics You can wash your less durable clothes on this program. Lighter washing movements and shorter washing cycle is used compared to “Cottons” program. It is recommended for your synthetic clothes (such as shirts, blouses, synthetic/cotton blended garments, etc.).
rinse hold and no spin options are shown respectively. ” and no spin is Rinse hold is shown with “ shown with “ ” symbols. If you do not want to unload your clothes immediately after the program, you may use the rinse hold function in order to prevent your clothes become wrinkled in an anhydrous condition. With this function, your laundry is kept in the final rinsing water. If you want to spin your laundry after the rinse hold function: - Adjust the spin speed. - Press “Start/Pause/Cancel” button.
Auxiliary functions Auxiliary Function Selection Buttons C Select the required auxiliary functions before starting the program. C Some combinations cannot be selected together. (Ex.: Pre-wash) (Figure 1-5a) and Quick Wash (Figure 1-5b). Auxiliary function selection If an auxiliary function that should not be selected together with a previously selected function is chosen, the first selected function will be cancelled and the last auxiliary function selection will remain active. (Ex.
5 Maintenance and cleaning Switching the machine to standby mode Detergent Drawer Remove any powder residue buildup in the drawer. To do this; 1. Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine. Press “Start/Pause/Cancel” button momentarily to switch your machine to the standby mode. Auxiliary functions can be cancelled or selected in accordance with the step the program is at.
Draining any remaining water and cleaning the pump filter Your product is equipped with a filter system which ensures a cleaner water discharge that extends pump life by preventing solid items such as buttons, coins and fabric fibers from clogging the pump propeller during discharge of the washing water. • If your machine fails to drain the water, the pump filter may be clogged. You may have to clean it every 2 years or whenever it is plugged. Water must be drained off to clean the pump filter.
6 Solution suggestions for problems Cause Explanation / Suggestion Program cannot be started or selected. • Machine may have switched to self protection mode due to an infrastructure problem (such as line voltage, water pressure, etc.). • Reset your machine by pressing “Start/ Pause/Cancel” button for 3 seconds. (see, Canceling a Program) There is water coming from the bottom of the machine. • Be sure the seals of the water inlet hoses are securely fitted. • Tightly attach the drain hose to the tap.
7 Specifications WM5 Models Maximum dry laundry capacity (kg) 5 Height (cm) 84 Width (cm) 60 Depth (cm) 45 Net Weight (±4 kg) 60 Electricity (V/Hz.) 220-240 V / 50Hz Total Current (A) 10 Total Power (W) 2000-2350 1000 Spinning cycle (rpm max.) Specifications of this appliance may change without notice to improve the quality of the product. Figures in this manual are schematic and may not match your product exactly.
- EN
- EN
ELECTRICAL DISTRIBRUTORS Service & Care Centre PTY LTD ABN 11 051 297 557 1/9 TERAN CLOSE WHITEBRIDGE NSW 2290 PH: 02 49 209114 FAX: 02 49209115 EMAIL: sales@euromaid.com.au WEBSITE: www.euromaid.com.
FOR OUTSIDE SERVICE AREAS PLEASE CONTACT OUR SERVICE & CARE CENTRE AT NEWCASTLE 02 49 209114
