600mm Curved Glass & Stainless Steel Canopy MODEL AAG6SE1 Installation and Operation
Canopy Installation and Operation Manual Dear Customer, We thank you for choosing this quality appliance and hope you enjoy many years of reliable service. Please ensure this manual is read carefully before installation and use. Keep this manual in a safe and accessible location should future reference be required. Regards Home Appliances CONTENT 2 …………………………………………………. Notice 3 …………………………………………………. Caution 4 …………………………………………………. Feature 5-8 ……………………………………………….. Installation 9 …………………………………………………..
Canopy Installation and Operation Manual NOTICE 1. Thank you for choosing our canopy rangehood. Please read the instruction manual carefully before use. 2. The installation work must be undertaken by a qualified and competent fitter. 3. The manufacturer disclaims all liability for any damage or injury caused as a result of not following instructions for installation contained in the following text. The cooker hood is used on 220/240v, 50Hz.
Canopy Installation and Operation Manual SAFETY WARNINGS Installation of this Integrated Canopy Rangehood must be carried by a qualified and competent installer. The manufacturer disclaims and liability for any damage or injury caused as a result of not following instruction of installation contained in this instruction manual. This Integrated Canopy Rangehood is not intended for use by young children or infirm persons without supervison.
Canopy Installation and Operation Manual (2)FEATURE 1. The cooker hood uses high quality materials, and is made with a streamlined design. 2. Equipped with a large power low noise electric motor and centrifugal leaf, it produces strong suction, low noise, non stick grease filter and easy to clean. 3. With the isolated low voltage circuit board control, 12vAC input, the lights are therefore safer. 4. Special wind tunnel construction and oil collector design, free dirt will be absorbed in a second.
Canopy Installation and Operation Manual (3). Installation If the model without Glass: 3.1 The cooker hood shall be placed at a distance of 65-75cm (26-30inch) from the cooking surface. See Pic 1. 3.2 Install the hook on a suitable place once the installation height is fixed, and keep it in line. The fixed position of the inside chimney bracket is the place of chimney. See Pic 2. 3.3 Fix one-way valve on the hood and connect the extensible pipe to the one-way valve. See Pic 3. 3.
Canopy Installation and Operation Manual Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards Home Appliances – October 2012 6
Canopy Installation and Operation Manual If the model with Glass: 3.1 The cooker hood shall be placed at a distance of 65-75cm (26-30inch) from the cooking surface. See Pic 1. 3.2 Install the hook on a suitable place once the installation height is fixed, and keep it in line. The fixed position of the inside chimney bracket is the place of chimney. See Pic 2. 3.3 Fix one-way valve on the hood and connect the extensible pipe to the one-way valve. See Pic 3. 3.4 Put the cooker hood on the hook. See Pic 4. 3.
Canopy Installation and Operation Manual Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards Home Appliances – October 2012 8
Canopy Installation and Operation Manual (4) NOTICE OF INSTALLATION 1. Before installation, please ensure the area is clean to avoid suction of the remaining bits of broken wood and dust. 2. It cannot share the same air ventilation tube with other appliance such as gas tube, warmer tube, and hot wind tube. 3. The bending of ventilation tube should be≥120°, parallel or above the start point and should be connected to the external wall. 4.
Canopy Installation and Operation Manual (5) SAFETY WARNING Keep your children from using the cooker hood. Your cooker hood is for domestic use only, not suitable for barbecue, roast shop and other commercial use. Any installation work must be carried out by a qualified electrician or competent person. The cooker hood and its filter mesh should be cleaned regularly in order to keep in good working order. Before cleaning, always ensure that you have switched your cooker hood off.
Canopy Installation and Operation Manual （6） USE Electronic Button 1. Turn on the power; the buzzer will buzz five times. The sound shows that the appliance is powered. 2. Push the low button, the indicating light 1 on, the buzzer will buzz once, and the motor runs at low speed. Push it again and the motor will stop. 3. Push the middle button, the indicating light 2 on, the buzzer will buzz once, and the motor runs at mid speed. Push it again and the motor will stop 4.
Canopy Installation and Operation Manual Push button 1. Push stop button, and the motor will stop. 2. Push the Low button, the buzzer will buzz once, and the motor runs at low speed. 3. Push the Mid button, the buzzer will buzz once, and the motor runs at mid speed. 4. Push the High button, the buzzer will buzz once, and the motor runs at high speed. 5. Push the light button and the two lights will come on. Push it again and the light will turn off.
Canopy Installation and Operation Manual LCD Electronic button Pic 7 1. Plug the hood; LCD will display 24-hour system with blue backlight. Backlight will be extinguished after 30 seconds without any operation. 2. Press “ ” button once; lights will be on and LCD will show “ button again; lights will be off and “ ” button will be on. Press “ speed. Press “ “ ” on LCD will disappear. ” ” button again; the hood works at MEDIUM ” button one more time; the hood works at HIGH speed.
Canopy Installation and Operation Manual button once; the number reduces by 01. When LCD shows 00; it doesn’t work by pressing “ ” button. After setting hour and minute; press “ ” to confirm. When “ ” button doesn’t work; “ ” button is used for delay timer function. Delay timer function allows you to set the hoods automatically power off according to the delay timer you set from 1 minute to 60 minutes. Press “ delay timer setting and LCD shows adds by 01. Continue pressing “ ; .
Canopy Installation and Operation Manual LCD Touch control Pic 8 1. Power on: Switch on the power supply, and the backlight is lit, displaying “24hour system”. The output is then blocked up,and the soot machine enters standby status. The backlight disappear automatically 30 seconds later under the condition of none operation. 2. on Press “Indicator” key: Press the indicator key once, the indicator is lit, and the LCD screen is lit.
Canopy Installation and Operation Manual key is null and void. If it is equal to 00, then, the void. key is null and Press the timer key for the 2nd time , time segment , and the last two minute bit segment flash, use key for the digit increase, and use key for the digit decrease. Namely: The variable is 01 each time it is pressed; the minute segment is with the largest digit of 59. If it exceeds key is null and void. If it is equal to 00, then, the key is null and 59, void.
Canopy Installation and Operation Manual (7) MAINTENANCE 7.1 The cleaning of the carbon grease filter mesh The filter mesh is made of high-density stainless steel. Please do not use the corrosive detergent on it. Keeping this filter clean will keep the appliance running correctly. Please strictly follow the guidelines below. Method 1: Put the mesh into 40-50 c clean water, pour on detergent, and soak for 23 mins. Wear gloves and clean with a soft brush.
Canopy Installation and Operation Manual (8) LIGHT REPLACING 8.1 halogen light: Use a small flat blade screwdriver to remove the inner stainless steel ring (when removing the inner ring, do so carefully so not to damage the range hood, as the glass lens could easily fall out of the inner ring) ; and remove carefully the halogen globe with a new one. 8.2 LED light: Remove the filters, and push the light downwards, and unplug the wiring connector.
Canopy Installation and Operation Manual （9） Abnormity and Solution Fault Light on, but motor does not work Light does not work, motor does not work Oil leakage Shake of the body Insufficient suction The machine inclines Cause The leaf blocked Get rid of the blocking The capacitor damaged Replace capacitor The motor jammed bearing Replace motor damaged The internal with of motor off or Replace motor a bad smell from the motor Beside the above mentioned, check the following: Light damaged Repla
