V09.1.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The computer is rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. • • 2. Do not place it on an unstable surface. Do not place anything heavy on the computer Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. • The power adapter may have either a 2-prong or a 3-prong grounded plug.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Pay careful attention to the instructions on swapping the battery. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter. However, check with your travel agent to see if you need any socket adapters.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the computer - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Upgrading the Memory and HDD/SSD If you want to upgrade your computer by upgrading the system memory or the hard disk drive/solid state drive you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the mainboard. Warranty Warning Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.
Preface Contents Notice .................................................................................I FCC Statement .............................................................II Instructions for Care and Operation .......................... IV Power Safety ............................................................... V Battery Precautions .................................................... VI Travel Considerations ...............................................VII Cleaning .......................
Preface 5-in-1 Card Reader ........................................................2-3 ExpressCard Slot ...........................................................2-4 Inserting and Removing ExpressCards .......................2-4 Audio Features ...............................................................2-5 Tablet PC Options ..........................................................2-6 Screen Orientation .......................................................2-7 Adding a Printer .........................
Preface Bluetooth Module .......................................................4-7 Wireless LAN Module ...............................................4-7 PC Camera Module ....................................................4-7 Fingerprint Reader Module ........................................4-7 BIOS Utilities Overview ........................................................................5-1 The Power-On Self Test (POST) ...................................5-2 Failing the POST ...........................
Preface Configuring the COM Port for the GPS Module ......6-23 RFID Reader Module ..................................................6-24 Configuring the COM Port for the RFID Reader .....6-25 Troubleshooting Overview ........................................................................7-1 Basic Hints and Tips ......................................................7-2 Backup and General Maintenance .................................7-3 Viruses ...............................................................
Preface Video Features .............................................................. D-9 Attaching Other Displays ........................................... D-12 Display Modes ............................................................ D-13 Power Management Features ...................................... D-17 The Power Sources ..................................................... D-18 Turning on the Computer ............................................ D-19 Power Schemes .................................
Preface XVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: A guide to using some of the main features of the computer e.g. the storage devices (hard disk/ Solid State Drive, 5-in-1 card reader, ExpressCard), Audio, Tablet PC Options & Printer. • Chapter 3 The computer’s power saving options.
1 Quick Start Guide Introduction This semi-ruggedized tablet computer provides an ideal platform for outdoor computer use with an IP54 (Ingress Protection) rating against dust and spray and features an optional sunlight readable LCD touch panel; all touch panels support both finger and stylus pen input.
Quick Start Guide Optional Accessories This computer features a range of options including a GPS module (including an optional active aerial), HF RFID reader, as well as a range of optional accessories including car adapter, charger box, USB to RS 232 cable, hand holder, shoulder strap and carrying handle.
1 Quick Start Guide Attaching the Optional Hand Holder. The hand holder offers ease of use when using the computer on the move outdoors. Attach the hand holder as follows: 1. 2. 3. 4. Place the hand holder at the rear of the computer with the screws facing inwards towards the computer. Align the screws on the hand holder with the screw holes 1 - 4 in the rear of the case (you may need to adjust the straps to do this). Fully tighten the screws 5 - 8 using a flathead screwdriver.
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1 and “BIOS Utilities” on page 5 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a of interest to you.
1 Quick Start Guide Not Included Operating Systems (e.g. Windows Vista or XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1 (you will need an external USB optical device drive).
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the following operating systems are supported.
1 Quick Start Guide System Startup 1. 2. Remove all packing materials. Place the computer flat on a stable surface with LCD panel facing upwards. Shutdown Touch Panel Input Device Please note that you should always shut your computer down by choosing the Turn Off Computer command from the Start menu in Windows. This will help prevent hard disk or system problems. External Optical (CD/DVD) Device Drives To install applications and drivers etc.
Quick Start Guide Operating System Setup If you are installing new system software, or are re-configuring your computer for a different system, make sure you configure the appropriate OS setting in the BIOS before installing a new operating system. 1. Start-up the computer and press to enter the BIOS. 2. Go to the Advanced menu, select “Installed O/S” and make sure the appropriate operating system is selected. 3.
1 Quick Start Guide System Software Installation Your computer may come with an operating system software and all necessary drivers pre-installed. If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers after installing the operating system.
Quick Start Guide Tablet Notebook Input Use the stylus pen provided to interact with the computer in the same way you would use the mouse (tap twice to double-click and keep the pen in contact with the screen to right-click). Before using the stylus pen you should calibrate the touch screen. Calibrating the Touch Panel 1. 2. 3. Double-click the Touch tool utility icon on the desktop OR from the Touch Package folder in the Programs/All Programs group (the driver must be installed). Click General.
1 Quick Start Guide 4. 5. 6. 7. Use the stylus pen to touch the blinking symbol until symbol changes color (maintain contact until the symbol stops blinking) and you will be prompted to lift up the pen. Repeat the process for all the remaining screen points. Click Free Draw (button) to test the calibration. Use the Mouse Emulation and Sound control panels to further adjust the settings to your preference.
Quick Start Guide Pen Options & Tablet Settings Configure the stylus pen input settings, from the Pen and Input Devices control pane in Windows Vista; the Tablet PC Settings control panel allows you to configure the tablet screen appearance. Access the control panels as follows: 1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Mobile PC and click Pen and Input Devices (or just double-click Pen and Input Devices).
1 Quick Start Guide On-Screen Keyboard The On-Screen Keyboard allows you to input text without the use of a keyboard. Move the pen over any character and then tap it to activate it. 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Ease of Access and click Start On-Screen Keyboard. Use the stylus pen to tap the appropriate keys to input. Click the Help menu to get more information.
Quick Start Guide System Map: LCD Panel View - Front Figure 1 - 10 LCD Panel View - Front 1 1. 2. 3. 2 7 7 3 4 4. 5. 6. 7.
1 Quick Start Guide LED Indicators The LED indicators on the computer display helpful information about the current status of the computer.
Quick Start Guide Function Buttons The function buttons provide easier access to functions on the computer.
1 Quick Start Guide On-Screen Menu Pressing the Menu button (or double-click the Pop Menu icon in the taskbar) on the computer will bring up the on-screen menu (make sure you install the pop menu driver - see “Pop Menu Utility” on page 4 - 6). Use the stylus pen to touch any of the buttons to activate the control. Press the Menu button (or double-click the Pop Menu icon in the taskbar) to quit the menu.
Quick Start Guide Function On-Screen Button Function Brightness Decrease/Increase Bluetooth Module Power Toggle Volume Decrease/ Increase PC Camera Module Power Toggle Mute Toggle G-Sensor Protection Mode Toggle Display Toggle GPS Module Power Toggle Display Battery Level RFID Module Power Toggle On-Screen Button WLAN Module Power Toggle Note: Any modules not included in your purchase configuration will appear grayed out when the key combination is pressed.
1 Quick Start Guide G-Sensor - Hard Disk Drive Protection The built-in G-Sensor gives protection to the system and hard disk (the G-Sensor does not function with Solid State Drives) in the event that the computer is accidentally dropped when the system is powered on (40cm drop approved when the system is powered on and 120cm drop approved when the system is powered off).
Quick Start Guide System Map: Rear View Figure 1 - 13 LCD Rear View - 2 1. 2. 1 3. 4. 3 3 4 5. 6. Built-In PC Camera GPS Active Aerial Socket (for optional Active Aerial) Protective Surround Stylus Pen & Holder Battery Gauge Battery 5 6 Battery Information See “Battery Information” on page 3 - 9 for full instructions.
1 Quick Start Guide Figure 1 - 14 Left View 1. 2. 3. 4. System Map: Left View Security Lock Slot Stylus Pen & Holder DC-In Jack 1 * USB 2.0 Port 1 3 1 2 3 4 Touch Panel Input Device Mouse & Keyboard You can use any external mouse and keyboard attached to any of the USB ports. 4 2 Do not use any sharp or pointed objects as your input device e.g. the end of a pen or pencil. You should only use the provided stylus pen (PDA type) as your input device.
Quick Start Guide System Map: Right View Figure 1 - 15 Right View 1. 2. 1 1 2 2 3 3. 4 4. 5 5.
1 Quick Start Guide Figure 1 - 16 Top & Rear Views 1. 2. 3. 4. 5. Strap Holders (for Carrying Strap) Power Button RFID (Radio Frequency Identification) Reader (Factory Option) RJ-45 LAN Jack 1 * USB 2.0 Ports System Map: Top & Bottom Views 1 2 1 3 4 5 External Optical (CD/DVD) Device Drives To install applications and drivers etc. you will need to attach an external optical CD/DVD device to the USB ports.
Quick Start Guide Windows Vista Start Menu & Control Panel Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
1 Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display Settings control panel (in Personalization) in Windows Vista as long as the appropriate Intel video driver is installed. To access Display Settings in Windows Vista: 1. 2. 3. 4. 5. 6. 7. Click Start, and click Control Panel (or point to Settings and click Control Panel).
Quick Start Guide 1 4 2 3 Figure 1 - 18 - Display Properties Desktop Intel Display Mode Description Single Mode One of the connected displays is used as the display device Intel(R) Dual Display Clone Mode Both connected displays output the same view and may be configured independently Extended Desktop Mode Both connected displays are treated as separate devices, and act as a virtual desktop Table 1 - 5 - Display Options Video Features 1 - 27 1
1 Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 25) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Quick Start Guide Optimizing Battery Life To optimize your battery life, follow the instructions below and also see “Conserving Battery Power” on page 3 - 10. You can check the battery’s current capacity from the gauge at the rear of the computer (see “Battery Gauge” on page 3 - 16). Set the Power Plan to Power saver: 1. Click Start, and click Control Panel (or point to Settings and click Control Panel). 2. 3. 4.
1 Quick Start Guide Removing the Battery If you need to remove the battery follow the procedure below. 1. 2. 3. 4. Turn the computer off (unless you are hot swapping the battery), and turn it over. Remove screws at points 1 - 4 . Remove the battery cover 5 . Grip the tab 6 and lift the battery out in the direction of the arrow 7 .
Quick Start Guide Hot-Swapping the Battery If you have more than one battery included in your purchase option you can swap the battery while the system is running. 1. 2. Check the level of the backup battery from the on-screen menu. Press the battery level button to display the indicator: Main Battery Level Bridge Battery Level Figure 1 - 22 - Battery Level Indicator 3. 4. 5. The lower indicator will display the bridge battery level and the upper indicator displays the main battery level.
1 Quick Start Guide 1 - 32
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer.
Features & Components 2 Upgrading the HDD/SSD If you want to upgrade your computer by upgrading the hard disk drive/solid state drive you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the computer. Hard Disk Drive/Solid State Drive The hard disk drive or solid state drive (factory options) is used to store your data in the computer.
Features & Components 5-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). • MMC (MultiMedia Card) • SD (Secure Digital) • Mini SD (requires PC adapter*) • SDIO (requires PC adapter*) • RS MMC (requires PC adapter*) Card Reader Cover Make sure you keep card reader cover closed when not in use.
Features & Components 2 ExpressCard Slot Cover ExpressCard Slot The computer is equipped with an ExpressCard 34 slot. ExpressCards are the successors to PCMCIA (PC Cards). Make sure you install the Card Reader driver Make sure you keep card reader cover closed when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. ExpressCard Support 1 2 Figure 2 - 2 Right View 1. 2.
Features & Components Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon to bring up an audio menu). The volume may be adjusted by means of the On-Screen Menu buttons or the volume icon in the taskbar (see sidebar).
Features & Components 2 Tablet PC Options Chapter 1 contains basic information on calibration (see “Calibrating the Touch Panel” on page 1 - 11), pen options and tablet settings (see “Pen Options & Tablet Settings” on page 1 - 13) and the On-Screen keyboard (see “On-Screen Keyboard” on page 1 - 14). The following pages will add some more detailed information on Tablet PC input and settings.
Features & Components Screen Orientation 2 If you prefer to orientate the screen differently follow these steps. Screen Orientation - Windows Control Panel 1. 2. 3. 4. 5. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Mobile PC (or just double-click Tablet PC Settings) and then click Tablet PC Settings. Click Display (tab) and select the orientation required. Click Apply. It is advisable to calibrate the touch panel after rotating the screen (see page 1 - 11).
Features & Components Screen Orientation - Intel GMA Control Panel 2 1. 2. 3. 4. 5. 6. Figure 2 - 5 Intel GMA Display Settings (Rotation) 2 - 8 Tablet PC Options Open the Display Settings control panel (see “Video Features” on page 1 - 26) and click Advanced Settings (button). Click the Intel(R)... tab and click Graphics Properties (button). Go to the Intel GMA control panel (see “Video Features” on page 1 - 26) and click Display Settings.
Features & Components Touch Package Settings You can also configure the pen options from the Touch Package control panel. 1. 2. 3. Double-click the Touch tool utility icon on the desktop OR from the Touch Package folder in the Programs/All Programs group (the driver must be installed). Click Mouse Emulation. Double-click either Drawing Mode or Button Mode to configure the Right-Click or Double-Click settings (you can also disable touch altogether if you prefer).
Features & Components Pen and Input Devices You can configure the pen options from the Pen and Input Devices control panel. 2 1. 2. 3. 4. Figure 2 - 7 Double Tap & Press and Hold Settings 2 - 10 Tablet PC Options Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Mobile PC (or just double-click Pen and Input Devices) and then click Pen and Input Devices. Select the Pen action from the left menu and click Settings to configure the setting.
Features & Components Other Useful Windows Vista Features for Tablet PC Users 2 Multi-Select Files in Windows Explorer The option to multi-select files in Windows Explorer in Windows Vista is very useful when using a pen as your input device. 1. 2. 3. 4. 5. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Appearance and Personalization and click Folder Options (or just double-click Folder Options).
Features & Components 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. 3 AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. Attach the AC/DC adapter to the DC-in jack on the left of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Press the power button and then release it to turn the computer “on”.
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on press the power button and release it. When the computer is on, you can use the power button as a Sleep/Hibernate hotkey button when you press and release it in less than 4 seconds (pressing the power button without releasing it for longer than this will force the computer to shut down). Use Power Options (Hardware and Sound menu) control panel in Windows Vista to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose High performance for maximum performance when the computer is powered from an AC power source.
Power Management 3 Power Button The Power Button in the Start Menu (in Classic View use the Shut Down button ) can be used to send the computer into a power-saving state. Sleep Mode & Mobile PC Battery A mobile PC in Sleep uses very little battery power. After an extended period of time the computer will save any open documents and applications to hard disk. Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power button, sleep button (on any attached keyboard) or Sleep command from the Lock Button Menu in Windows Vista may be set to send the computer in to a power-saving state. It is recommended that you enable a password on wake up in order to protect your data.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button on an attached keyboard.
Power Management 3 Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Please follow these simple guidelines to get the best use out of your battery. Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g.
Power Management Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. • Reduce the amount of time before the display is turned off. • Close wireless, Bluetooth or communication applications when they are not being used.
Power Management Battery Life 3 Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 1 - 30.
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Caution Danger of explosion if battery is incorrectly replaced. Damaged Battery Warning Should you notice any physical defects (e.g.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 3 1. 2. 3. Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options. Choose the options below (click Yes if a warning appears).
Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. 3 How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. Battery Gauge The battery gauge at the rear of the computer provides a clear indication of remaining battery life. Firmly press the PUSH CHECK button and the Led will show the current battery level.
Power Management Battery Indicators On-screen indicators will display the battery status if the battery level button is pressed or the AC/DC adapter is not connected. Action Icon Description The on-screen Main Battery Level Indicator battery level button is pressed.
Power Management 3 3 - 18
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Drivers (button) to access the optional driver menu. 1. 2. 4 3. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
Drivers & Utilities Vista (SP1) Driver Page # Chipset Page 4 - 5 Video Page 4 - 5 LAN Page 4 - 5 Touch Panel Application Page 4 - 6 Pop Menu Utility Page 4 - 6 Audio Page 4 - 6 Wireless LAN Module Page 6 - 6 PC Camera Module Page 6 - 11 Fingerprint Reader Module Page 6 - 17 Manual Driver Installation Click Browse CD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder.
Drivers & Utilities 4 Updating/Reinstalling Individual Drivers User Account Control (Win Vista) If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer).
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc into your attached CD/DVD drive and click Install Drivers (button), or Option Drivers (button) to access the optional driver menu. Driver Installation General Guidelines The driver installation procedure outlined in this Chapter (and in Chapter 7 Options & Modules), are accurate at the time of going to press.
Drivers & Utilities 4 Touch Panel Application 1. Click 4.Install Touch Panel Driver > Yes. 2. Click Next > Next > Install. 3. Click Finish. 4. Click OK to restart the computer. 5. You will then need to calibrate the touch panel (see “Calibrating the Touch Panel” on page 1 - 11). Pop Menu Utility 1. Click 5.Install POP Menu Utility > Yes. 2. Click Next > Install. 3. Click Finish > Finish to restart the computer. 4. See “On-Screen Menu” on page 1 - 18 for details. Audio 1. Click 6.
Drivers & Utilities Optional Drivers Bluetooth Module See the pages indicated overleaf for the driver installation procedures for any modules included in your purchase option. Note: The operating system is the default setting for Bluetooth control in Windows Vista, and does not require a driver. See “Bluetooth Module” on page 6 - 2 for configuration instructions. Wireless LAN Module See the introduction in “Wireless LAN Module” on page 6 - 6, and check the installation procedure.
Drivers & Utilities 4 4 - 8
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility Note that you will need to attach a USB keyboard to one of the USB ports in order to edit the BIOS settings. BIOS Settings Warning Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Setup Defaults with .
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured right is for guideline purposes only. The POST screen on your computer may appear slightly different. If you disable the Boottime Diagnostic Screen (see page 5 - 9), the POST screen will not appear.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Note that you will need to attach a USB keyboard to one of the USB ports in order to edit the BIOS settings. 5 Entering Setup To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds after you turn on the system.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu Phoenix SecureCore(tm) Setup Utility Figure 5 - 2 Main Main Advanced Security Boot Exit Main Menu Item Specific Help System Time: 5 System Date: [22:12:05] [04/24/2009] Large Disk Access Mode: [DOS] Primary Master Primary Slave [TOSHIBA MK1246GSX-(P] [None] System Memory Extended Memory 640 KB 1014 MB BIOS Revision KBC/EC Firmware Revision ******** ******** F1 Esc Help Exit Select Item Select Menu -/+ Enter , , or selects
BIOS Utilities Large Disk Access Mode (Main Menu) This refers to the representation of hard disk drive geometries as addressed by different operating systems. Select “Other” if you are using systems such as Novell, UNIX etc. Select “DOS” (default) if you are using Windows. Primary Master/ Primary Slave (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a HDD/optical device on the computer’s Primary Master/Primary Slave channels is applicable.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu Phoenix SecureCore(tm) Setup Utility Main A dvanced Advanced Security Boot Exit Item Specific Help Installed O/S: Reset Configuration Data: Boot-time Diagnostic Screen: POST Boot Sound Battery Low Alarm Beep: Hyperthreading: 5 [WinXP/Vista] [No] [Disabled] [Disabled] [Disabled] [Enabled] Select the operating system installed on your system which you will use most commonly.
BIOS Utilities Reset Configuration Data (Advanced Menu) This item is set to No as default. You can change the setting to Yes if you have installed a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot. Boot-time Diagnostic Screen (Advanced Menu) Use this menu item to enable/disable the Boot-time Diagnostic Screen (see Figure 5 - 1 on page 5 - 2).
BIOS Utilities Security Menu Security Menu Phoenix SecureCore(tm) Setup Utility Main Advanced Security Security Boot Exit = 5 Item Specific Help The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.
BIOS Utilities Set User Password (Security Menu) You can set a password for user mode access to the Phoenix SecureCore Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below). Many menu items in the Phoenix SecureCore Setup Utility cannot be modified in user mode. You can only set the user password after you have set the supervisor password.
BIOS Utilities Password Warning 5 If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. 5 - 12 Security Menu System backup reminder (Security Menu) You can set a system backup reminder here to be enabled at system boot.
BIOS Utilities Boot Menu Phoenix SecureCore(tm) Setup Utility Main Advanced Security Boot Figure 5 - 5 Exit Item Specific Help Boot priority order: 1: IDE FDC: 2: USB CDROM: 3: USB KEY: 4: USB HDD: 5: PCI SCSI: 6: IDE CD: 7: IDE HDD: TOSHIBA MK1246GSX-(PM) 8: PCI BEV: Realtek Boot Agent Excluded from boot order: : USB ZIP: : USB LS120: : Other USB: : 1394 CDROM: F1 Esc Help Exit Select Item Select Menu -/+ Enter Boot Menu Keys used to view or configure devices: Up and Down arrows select
BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu Phoenix TrustedCore(tm) Setup Utility Main Advanced Security Boot Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes 5 F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
Modules Chapter 6: Modules Overview This chapter contains information on the following modules, which come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • • • • • • Bluetooth Module (Factory Option) Wireless LAN Module PC Camera Module Fingerprint Reader Module GPS Module RFID Reader Module Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Modules Wireless Device Operation Aboard Aircraft 6 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Bluetooth Module The operating system’s Bluetooth Devices (the Bluetooth module is a Factory Option) control panel is used to configure the Bluetooth settings in Windows Vista, and therefore does not require a driver.
Modules Bluetooth Configuration in Windows Vista Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). To Turn the Bluetooth Module On 1. 2. 3. Press the On-Screen Menu button to toggle power to the Bluetooth module. A Bluetooth icon will appear in the taskbar (see sidebar). You can then do any of the following to access the Bluetooth Devices control panel.
Modules Passkey Options 6 You can allow the system to choose a passkey for you. You will then be prompted to enter the generated passkey on your Bluetooth device. To Add a Bluetooth Device 1. 2. 3. 4. 5. Access the Bluetooth Devices control panel. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. Click Devices (tab), and then click Add. The Add Bluetooth Device Wizard will appear.
Modules To Change Settings for the Bluetooth Device 1. 2. Access the Bluetooth Devices control panel. Click on the device you want to change and click Properties to: • • Change the name of the device (click General, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. Access the Bluetooth Devices control panel.
Modules Wireless Device Operation Aboard Aircraft 6 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the On-Screen Menu button to toggle power to the WLAN module, and check the menu icon to see if the module is powered on or not (see Table 1 - 4, on page 1 - 19).
Modules Connecting to a Wireless Network Make sure the Wireless LAN module is turned on. 1. Click the taskbar wireless icon , and then click Connect to a network (or rightclick the icon , and then click Connect to a network). Figure 6 - 5 Taskbar Menus Click icon Right-click icon 2. 3. In the Show list, click to choose Wireless from the drop-down menu. A list of currently available networks will appear.
Modules 4. 5. Click a network, and then click Connect. If you do not see a network you want to connect to, click Set up a connection or network (a list of options will appear allowing manual searching, and creating a new network). 6. Move the cursor over the taskbar icon Figure 6 - 7 Connecting 6 Figure 6 - 8 Connection Status 6 - 8 Wireless LAN Module to see the connection status (see below).
Modules 7. To disconnect from the wireless network you can click the taskbar wireless icon , and then select Connect or disconnect to access the network menu, and click Disconnect (or right-click the icon , and then click Disconnect from). Click icon Security Enabled Networks You should try to make sure that any network you are connecting to is a secure network. Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. 6 Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules PC Camera Module Before installing the PC Camera module driver use the On-Screen Menu button to power ON (the default setting is OFF) the PC Camera module (see “OnScreen Menu” on page 1 - 18). Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. PC Camera Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into your external optical device drive. 2. Click 2.Install Camera Driver > Yes. 3.
Modules PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. 6 Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone (Realtek High Definition Audio) and make sure the item is not disabled. 5. Double-click Microphone (or select Properties from the right-click menu). 6.
Modules Figure 6 - 11 Audio Setup for PC Camera 6 Right-click PC Camera Module 6 - 13
Modules Pre-Allocating File Space You may pre-allocate the file size (File > Allocate File Size) for the capture file in the BisonCap program. 6 BisonCap BisonCap is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format. 1. 2. 3. Run the BisonCap program from the Start > Programs/All Programs > BisonCam menu (it is recommended that you set the capture file before the capture process - see Set Capture File below).
Modules Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules Zoom The BisonCap program allows you to zoom the camera in and out. 1. 2. Run the BisonCap program. Go to Zoom and select Zoom Out/Zoom In. Figure 6 - 12 Zoom/Setting 6 Snapshot Folder The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture. If you accidentally delete or move the folder, you can create a new Snapshot folder on the desktop in order to capture the files.
Modules Fingerprint Reader Module If you have included the fingerprint reader in your purchase option you will need to install the driver as per the instructions below. Help & Manual Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. Right-click the taskbar icon to bring up the menu to select Help. Before beginning the enrollment process it is recommended that you go through the fingerprint tutorial.
Modules User Enrollment 1. Fingerprint Enrollment 2. Note that it is strongly recommended that you enroll more than one finger in case of injury etc. 6 3. 4. 5. Click Start > Programs/All Programs > Protector Suite > Control Center, or double click the taskbar icon (click Initialize). On the first run of the program you will be asked to click the Accept button to accept the license.
Modules 6. Click the button above any of the fingers to begin the enrollment process for that finger. 7. Swipe the finger until the progress bar reaches 100% to enroll that finger. 8. Repeat the process for all the fingers you wish to enroll (see sidebar), and then click Save and Continue. 9. Enter a backup password and click Apply. 10. Close the fingerprint status window. Fingerprint Enrollment Note that it is strongly recommended that you enroll more than one finger in case of injury etc.
Modules 11. Right-click the taskbar icon and select Start Control Center (and then swipe a finger) to allow you to Edit Fingerprints, register Applications, edit Settings and access the Help menu etc. You can also run the Control Center etc. from the Protector Suite item in the Programs/All Programs menu 12. Click “Help” in Control Center Home to get more information on any topic. 13. You can also run the Tutorial, or Product Tour video to get more information.
Modules Fingerprint Control Center Features Application Launcher The Application Launcher allows you to register applications to be launched when assigned to a particular finger. Simply copy the application icon on to one of the registered fingers and ten click OK to close the application window. Once registered the application will launch when you swipe the appropriate finger across the sensor.
Modules GPS Module If you have included an Global Positioning System (GPS) receiver module in your purchase option, you will need to obtain map software suitable for your global location. Map software programs are both commercially available and downloadable directly from the internet. A Global Positioning System satellite continually transmits high-frequency radio signals containing the time and location of the satellite in relation to the earth.
Modules Configuring the COM Port for the GPS Module You need to make sure that the COM port for the GPS module is set to COM 3 at a 4800 baud rate. To do this follow the instructions below: 1. 2. 3. 4. 5. 6. Click Start (menu), point to Settings and click Control Panel (or click Control Panel). Double-click Device Manager (icon); Device Manager (icon) is in Hardware and Sound (category). Click “+” next to Ports (COM & LPT) if its sub-items are not shown. Double-click Communications Port (COM3).
Modules RFID Reader Module If you have included the RFID Reader module in your purchase option, you will need to obtain software suitable for your system. The scanner for the module is located at the top of the computer. • For RFID Reader - Simply hold any RFID enabled card (up to a distance of 2CM) in front of the scanner to obtain a reading.
Modules Configuring the COM Port for the RFID Reader You need to make sure that the COM port for the RFID reader is set to COM 1 at a 9600 baud rate. To do this follow the instructions below: 1. 2. 3. 4. 5. 6. Click Start (menu), point to Settings and click Control Panel (or click Control Panel). Double-click Device Manager (icon); Device Manager (icon) is in Hardware and Sound (category). Click “+” next to Ports (COM & LPT) if its sub-items are not shown. Double-click Communications Port (COM1).
Modules 6 6 - 26
Troubleshooting Chapter 7: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Indicators (see “LED Indicators” on page 1 - 16) to see the computer’s power status. • Connections - Check all the cables to make sure that there are no loose connections anywhere.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. 7 • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing (please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty). • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator , is blinking orange. Low Battery. Plug in the DC power source.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer isn’t sitting on a thermal surface. Make sure you’re using the correct adapter. Make sure that your computer is completely powered off before putting it into a travel bag (or any such container). Nothing screen. appears on The system is in a power saving mode. Press the power button (see “Configuring the Power Button” on page 3 - 8). The screen controls need to be adjusted.
Troubleshooting Problem You forget password. the Possible Cause - Solution boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting 7 Problem Possible Cause - Solution The Hibernate function has disappeared (in Windows Vista). You have a computer with 4GB of RAM and have installed Windows Vista Service Pack 1. This is a known issue if your computer has 4GB of RAM and is running Windows Vista Service Pack 1. To re-enable Hibernate mode go to the Command Prompt and type the command “powercfg -h on” (make sure you are logged on as an Administrator): 1. 2. 3. 4. 5. 6. Click Start (menu button).
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc. Ports and Jacks View Port/Jack Left View 1 2 3 Description 1.Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. 2.
Interface (Ports & Jacks) View Right View Port/Jack Description 4.Headphone-Out Jack Headphones or speakers may be connected through this jack. Note: Set your system’s volume to a reduced level before connecting to this jack. 5.External Monitor Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD. 6.RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g.
Intel Video Driver Controls Appendix B: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 26. Intel Video Driver Installation DVMT Notes Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Video Driver 1. Insert the Device Drivers & Utilities + User’s Manual disc into an attached CD/DVD drive. 2. Click Install Drivers. 3. Click 3.Install Video Driver > Yes. 4. Click Next > Yes > Next > Next. 5.
Intel Video Driver Controls Taskbar Icon The Intel GMA control panel can also be accessed by clicking the icon in the taskbar and selecting Graphics Properties from the menu. Intel Graphics Properties More advanced video configuration options are provided by the Intel(R) Graphics Media Accelerator Driver for ultra mobile. 1. 2. Open the Display Settings control panel (see “Video Features” on page 1 - 26) and click Advanced Settings (button). Click the Intel(R)...
Intel Video Driver Controls You may make changes to the devices, color, schemes, Hot Keys etc. by clicking the appropriate menu item or button. Click Information (button) to obtain useful information about the graphics properties of the computer, and see the Support tab in Information to get weblinks to the latest information on the Intel Website. Help Menus Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu.
Intel Video Driver Controls Display Settings You can adjust the Color Quality, Screen Resolution and Refresh Rate for any attached display(s) from the Intel(R) GMA Driver for ultra mobile control panel, or from Display Settings (see page 1 - 26) in Windows. Note: MID (Mobile Internet Device) is the computer’s LCD display.
Intel Video Driver Controls Power Settings Use the Power Settings control to allow the Intel(R) GMA Driver for ultra mobile control panel to adjust the power options when the computer is running on battery power. To set the power settings: 1. 2. 3. 4. 5. 6. Attach your external monitor to the external monitor port, and turn it on. Go to the Intel GMA control panel (see “Intel Graphics Properties” on page B 2) and click Display Settings. Click Power Settings (button).
Intel Video Driver Controls On-Screen Menu Button You can use the OnScreen Menu button to quickly toggle through the display options. Attaching Other Displays Besides the built-in LCD, you can also use an external monitor/flat panel display, connected to the external monitor port at the rear of the computer, as your display device. The following are the display options: 1. 2. The built-in LCD OR an external monitor/flat panel display connected to the external monitor port (Single Display).
Intel Video Driver Controls Configuring Displays from Intel® GMA Driver for ultra mobile 1. 2. 3. Go to the Intel GMA control panel (see “Intel Graphics Properties” on page B 2) and click Display Devices. Click to choose the display option from the Multiple Display menu. Click Apply (and OK to confirm the settings change) and OK (button). Multiple Display At least one other display must be attached in order to view Multiple Display options.
Intel Video Driver Controls Display Modes Single Display Only one of your attached displays is used. Intel(R) Dual Display Clone (mirrored) This mode will drive multiple displays with the same content. Each device may be configured independently for different resolutions, refresh rates, color quality etc. Use this feature to display the screen through a projector for a presentation. Extended Desktop (extended) This mode allows a desktop to span multiple displays and acts as a large workspace.
Intel Video Driver Controls To Enable Intel(R) Dual Display Clone 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port, and turn it on. Go to the Intel GMA control panel (see “Intel Graphics Properties” on page B 2) and click Display Devices. Click to choose Intel(R) Dual Display Clone (Multiple Display). Click Apply, and OK to confirm the settings change. Click Display Settings to adjust the settings for the attached devices.
Intel Video Driver Controls To Enable Extended Desktop Display Settings Extended Desktop You can have different Colors, Screen Area and Monitor Refresh Rates for each display device provided your monitor can support them. 1. 2. 3. 4. 5. You can drag the monitor icons to match the physical layout of your displays. Icons and programs may also be dragged between the displays.
Intel Video Driver Controls Using Windows Vista to Enable Extended Mode 1. 2. 3. 4. 5. Attach your external display to the external monitor port, and turn it on. If a New Display Detected window does not appear in Windows Vista, go to the Windows Mobility Center control panel (Mobile PC > Adjust commonly used mobility settings) and click Connect display. Click to select Show different parts of my desktop on each display (extended). Click Right or Left under Extend your desktop. Click Apply > OK.
Intel Video Driver Controls Using Display Settings to Enable Extended Mode 1. 2. 3. Attach your external display to the external monitor port, and turn it on. Open the Display Settings control panel (see “Video Features” on page 1 - 26). Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend my Windows desktop onto this monitor.” and click Apply. Click the appropriate monitor icon (e.g. 2 ) to be able to select the option to extend the desktop on to it.
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.
Specifications Processor Options Video Adapter Audio Intel® Atom Processor: Intel® US15W Integrated Video (Intel® Graphics Media Accelerator 500) Intel® High Definition Audio Built-In Microphone 2 * Built-In Speakers (1.5W) 512K On-die L2 Cache, 533MHz FSB, FC-BGA8 Package Z520 (1.33GHz), Z530 (1.60GHz), Z540 (1.86GHz) Core Logic Intel® US15W Chipset LCD Options 8.9” WSVGA (1024 * 600) TFT LED Backlight LCD with Touch Panel (Stylus Pen & Finger Sensitivity) - Factory Option 8.
Specifications Card Reader/ExpressCard Power Dimensions & Weight Intel® US15W Integrated 5-in-1 Card Reader (SD/ Mini SD/ SDIO/ MMC/ RS MMC) Note: Mini SD/ SDIO/ RS MMC Cards require a PC adapter One ExpressCard 34 Slot (see Approved ExpressCard list in Table E - 1, on page E - 1) Full Range AC/DC Adapter AC input 100 - 240V, 50 - 60Hz, DC Output 19V, 1.58A or 19V, 1.57A (30 Watts) Li-Polymer 6600mAH Battery Pack Energy Star 4.
Specifications Factory Options GPS Module Bluetooth 2.1 + EDR (Enhanced Data Rate) Module HF RFID Reader 8.9” WSVGA (1024 * 600) TFT LED Backlight LCD with Touch Panel (Stylus Pen & Finger Sensitivity) 8.
Windows XP Information Appendix D: Windows XP Information This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows XP OS.
Windows XP Information Tablet Notebook Input Use the stylus pen provided to interact with the computer in the same way you would use the mouse (tap twice to double-click and keep the pen in contact with the screen to right-click). Before using the stylus pen you should calibrate the touch screen. Calibrating the Touch Panel 1. 2. 3. Double-click the Touch tool utility icon on the desktop OR from the Touch Package folder in the Programs/ All Programs group (the driver must be installed). Click General.
Windows XP Information 4. 5. 6. 7. Use the stylus pen to touch the blinking symbol until symbol changes color (maintain contact until the symbol stops blinking) and you will be prompted to lift up the pen. Repeat the process for all the remaining screen points. Click Free Draw (button) to test the calibration. Use the Mouse Emulation and Sound control panels to further adjust the settings to your preference.
Windows XP Information On-Screen Menu Pressing the Menu button (or double-click the Pop Menu icon in the taskbar) on the computer will bring up the on-screen menu (make sure you install the pop menu driver - see “Pop Menu Utility” on page D - 35). Use the stylus pen to touch any of the buttons to activate the control. Press the Menu button (or double-click the Pop Menu icon in the taskbar) to quit the menu.
Windows XP Information Function On-Screen Button Function Brightness Decrease/Increase Bluetooth Module Power Toggle Volume Decrease/ Increase PC Camera Module Power Toggle Mute Toggle G-Sensor Protection Mode Toggle Display Toggle GPS Module Power Toggle Display Battery Level RFID Module Power Toggle On-Screen Button WLAN Module Power Toggle Note: Any modules not included in your purchase configuration will appear grayed out when the key combination is pressed.
Windows XP Information G-Sensor - Hard Disk Drive Protection The built-in G-Sensor gives protection to the system and hard disk (the G-Sensor does not function with Solid State Drives) in the event that the computer is accidentally dropped when the system is powered on (40cm drop approved when the system is powered on and 120cm drop approved when the system is powered off).
Windows XP Information Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Windows XP Information Audio Features You can configure the audio options on your computer from the Sounds and Audio Devices Windows control panel, or from the Realtek HD Audio Manager icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration menus). The volume may be adjusted by means of the On-Screen Menu buttons or the volume icon in the taskbar (see below).
Windows XP Information Video Features You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate Intel video driver is installed. To access Display Properties in Windows: 1. 2. 3. 4. 5. 6. 7. Click Start, point to Settings and click Control Panel (or just click Control Panel). Double-click Display (icon) - In the Appearances and Themes category. Click Settings (tab) in the Display Properties dialog box.
Windows XP Information Display & Graphics Properties Taskbar Icon Besides the built-in LCD, you can also use an external VGA monitor (CRT) or external Flat Panel Display connected to the external monitor port as your display device. You can also access the controller properties from the taskbar. Click on the icon to bring up the menu and scroll to Graphics Properties.
Windows XP Information You may make changes to the devices, color, schemes, Hot Keys etc. by clicking the appropriate menu item or button. Help Menus Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu. Multiple Display At least one other display must be attached in order to view Multiple Display options.
Windows XP Information Attaching Other Displays Besides the built-in LCD, you can also use an external monitor/flat panel display as a display device. The following are the display options: 1. 2. The built-in LCD OR an external monitor/flat panel display connected to the external monitor port (Single Display). The built-in LCD AND an external monitor/flat panel display connected to the external monitor port (Multiple Display). If you want use an external display follow these instructions: 1. 2. 3. 4.
Windows XP Information Display Modes Single Display Only one of your attached displays is used. On-Screen Menu Button Intel(R) Dual Display Clone This mode will drive multiple displays with the same content. Each device may be configured independently for different resolutions, refresh rates, color quality etc. Use this feature to display the screen through a projector for a presentation. You can use the OnScreen Menu button to quickly toggle through the display options.
Windows XP Information To Enable Intel(R) Dual Display Clone Mode 1. 2. 3. 4. 5. Attach your external display to the external monitor port and turn it on. Open the Intel(R) GMA Driver for ultra mobile control panel. Click to choose Intel(R) Dual Display Clone from Display Devices (tab). Click Apply, and OK to confirm the settings change. Click Display Settings to adjust the settings for the attached devices.
Windows XP Information To Enable Extended Desktop Mode: 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port and turn it on. Open the Intel(R) GMA Driver for ultra mobile control panel. Click to choose Extended Desktop from Display Devices (tab). Click Apply, and OK to confirm the settings change. Click Display Settings to adjust the settings for the attached devices.
Windows XP Information To Enable Extended Desktop (Display Properties) 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port and turn it on. Click Start, point to Settings (or click Control Panel) and click Control Panel (if you are in Category View choose Appearance and Themes). Double-click Display (icon). In the Display Properties dialog box, click Settings (tab). Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend my Windows desktop onto this monitor.
Windows XP Information Power Management Features To conserve power, especially when using the battery, your computer uses the ACPI power management system. Power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system. The Power Options control panel icon in Windows allows you to configure power management features for your computer.
Windows XP Information The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/DC adapter will damage the computer and its components. 1. 2. 3. 4. 5. Attach the AC/DC adapter to the DC-in jack on the left of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Press the power button to turn the computer “on”.
Windows XP Information Turning on the Computer Now you are ready to begin using your computer. To turn it on press the power button and release it. When the computer is on, you can use the power button as a Sleep/Hibernate hot-key button when you press and release it in less than 4 seconds (pressing the power button without releasing it for longer than this will force the computer to shut down). Use Power Options (Hardware and Sound menu) control panel in Windows Vista to configure this feature.
Windows XP Information Resuming Operation Press a key on an attached keyboard, or move an attached mouse/TouchPad to resume from Monitor or Hard Disk Stand by. Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes.
Windows XP Information Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Windows XP Information System Power Options You can use the system power options to stop the computer’s operation and restart where you left off. This system features Stand by and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - see “Hibernate” on page D - 23). Hibernate Mode vs. Shutdown Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to turn it on.
Windows XP Information Stand by Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Stand by mode to save power.
Windows XP Information Configuring the Power Button The power button may be set to send the computer in to either Stand by or Hibernate mode. In Stand by mode, the LED will blink green. In Hibernate mode the LED will be off (battery) or orange (AC/DC adapter). If you are in a power saving mode set to save power through individual components (e.g. hard disk, screen), the LED will remain green.
Windows XP Information Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery Warning New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page D - 28 for instructions on how to do this). Battery Life Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached.
Windows XP Information Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. If you need to remove the battery for any reason, see “Removing the Battery” on page D - 30. Recharging the Battery with the AC/DC Adapter The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet.
Windows XP Information Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Windows XP Information Battery FAQ Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery.
Windows XP Information Battery Indicators On-screen indicators will display the battery status if the battery level button adapter is not connected. Action Icon is pressed or the AC/DC Description The on-screen Main Battery Level Indicator battery level button is pressed.
Windows XP Information Removing the Battery If you need to remove the battery follow the procedure below. 1. 2. 3. 4. Turn the computer off (unless you are hot swapping the battery), and turn it over. Remove screws at points 1 - 4 . Remove the battery cover 5 . Grip the tab 6 and lift the battery out in the direction of the arrow 7 .
Windows XP Information Hot-Swapping the Battery If you have more than one battery included in your purchase option you can swap the battery while the system is running. 1. 2. Check the level of the backup battery from the on-screen menu. Press the battery level button to display the indicator: Main Battery Level Bridge Battery Level Figure D - 18 - Battery Level Indicator 3. 4. 5. The lower indicator will display the bridge battery level and the upper indicator displays the main battery level.
Windows XP Information Driver Installation You will need to attach a CD/DVD drive to the computer in order to access the drivers on the Device Drivers & Utilities + User’s Manual disc. This contains the drivers and utilities necessary for the proper operation of the computer. 1. Check the driver installation order from Table D - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below. 2.
Windows XP Information WinXP SP3 Driver Page # Chipset Page D - 34 Windows XP Service Pack 3 Video Page D - 34 Audio Page D - 34 Make sure you install Windows XP Service Pack 3 (or a Windows XP version which includes Service Pack 3) before installing any drivers.
Windows XP Information Updating/Reinstalling Individual Drivers Driver Installation Procedure If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and doubleclick the Add/Remove Programs item. If you see the individual driver listed (if not see below), uninstall it, following the on screen prompts (it may be necessary to restart the computer).
Windows XP Information LAN 1. Click 4.Install LAN Driver > Yes. 2. Click Next > Install. 3. Click Finish. 4. The network settings can now be configured. Module Drivers See the following pages for the driver installation procedures for any of the optional modules included in your purchase configuration. Touch Panel Application 1. Click 5.Install Touch Panel Driver > Yes. 2. Click Next > Next > Install. 3. Click Finish. 4. Click OK to restart the computer. 5.
Windows XP Information Bluetooth Module Note: The operating system is the default setting for Bluetooth control in Windows XP, and does not require a driver. See “Bluetooth Module” on page D 37 for configuration instructions. Wireless LAN Module See “Wireless LAN Module” on page D - 42. PC Camera Module See “PC Camera Module” on page D - 44. Fingerprint Reader Module See “Fingerprint Reader Module” on page D - 49.
Windows XP Information Bluetooth Module The operating system’s Bluetooth Devices (the Bluetooth module is a Factory Option) control panel is used to configure the Bluetooth settings in Windows XP, and therefore does not require a driver. Use the On-Screen Menu button to power ON the Bluetooth module (see “On-Screen Menu” on page D - 4).
Windows XP Information Bluetooth Local Area Connection Icon If you want to display the Local Area Connection icon for the Bluetooth connection in the taskbar, set it up as follows: 1. Access the Network Connections control panel in Windows (Start > Settings > Network Connections OR Start > Connect To > Show all Connections) or by clicking the taskbar icon . 2. Right-click the Bluetooth connection icon, and select Properties. 3.
Windows XP Information Bluetooth Configuration in Windows XP Setup your Bluetooth Device so the Computer Can Find it 1. 2. Bluetooth Taskbar Icon Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). To Turn the Bluetooth Module On 1. 2. 3. Press the On-Screen Menu button to toggle power to the Bluetooth module. A Bluetooth icon will appear in the taskbar (see sidebar).
Windows XP Information To Add a Bluetooth Device Figure D - 25 1. Access the Bluetooth Devices control panel. 2. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. 3. Click Devices (tab), and then click Add. 4. The Add Bluetooth Device Wizard will appear. 5. Click to select “My device is set up and ready to be found”, and then click Next.
Windows XP Information To Change Settings for the Bluetooth Device 1. 2. • • Access the Bluetooth Devices control panel. Click on the device you want to change and click Properties to: Change the name of the device (click General, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). Bluetooth Module & Resuming From Sleep Mode To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3.
Windows XP Information Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the On-Screen Menu button to toggle power to the WLAN module, and check the menu icon to see if the module is powered on or not (see Table D - 1, on page D - 5).
Windows XP Information Network Connection Use the Windows Network Connections control panel to access available wireless networks (Start > Settings > Network Connections or Start > Connect To > Show all Connections).
Windows XP Information Camera Button Press the Camera Button to run the BisonCap application program. When the BisonCap application is running, press the Camera Button to take a still picture (see also “Taking Still Pictures” on page D - 48). Note press the Camera Button and release it after you hear the camera shutter sound.
Windows XP Information PC Camera Audio Setup To capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double-click the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View). 2. Click Advanced in the Volume > Device volume tab. 3. Click Options and scroll down and click Properties. 4.
Windows XP Information Pre-Allocating File Space You may pre-allocate the file size (File > Allocate File Space) for the capture file in the BisonCap program. Pre-allocating space on the hard disk can improve the capture quality (particularly of large capture files), by reducing the amount of work the hard disk has to do in finding space for the video data as it is being captured. See also “Reducing Video File Size” on page D - 47.
Windows XP Information Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties) If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Windows XP Information Snapshot Folder The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture. If you accidentally delete or move the folder, you can create a new Snapshot folder on the desktop in order to capture the files. Zoom The BisonCap program allows you to zoom the camera in and out. 1. Run the BisonCap program. 2. Go to Zoom and select Zoom Out/Zoom In.
Windows XP Information Fingerprint Reader Module If you have included the fingerprint reader in your purchase option you will need to install the driver as per the instructions below. Help & Manual Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. Right-click the taskbar icon to bring up the menu to select Help. Before beginning the enrollment process it is recommended that you go through the fingerprint tutorial.
Windows XP Information User Enrollment 1. Click Start > Programs/All Programs > Protector Suite QL > User Enrollment, or double click the taskbar icon (click Initialize). 2. On the first run of the program you will be asked to click the button to accept the license, and then click OK. 3. Click Next (the enrollment method will automatically be configured). 4.
Windows XP Information 9. 10. 11. 12. 13. 14. 15. 16. Click Next > Next (if you have the “Run interactive tutorial” tickbox selected you will run through the Fingerprint Tutorial). Click Next for each window of the tutorial (you can click the button to “skip tutorial” at any time). Click the button above any of the fingers to begin the enrollment process for that finger. Swipe the finger five times to enroll that finger.
Windows XP Information 17. Right-click the taskbar icon to Start Control Center to allow you to Edit Fingerprints, register applications, manage Password Bank, File Safe and access the Help menu etc. You can also run the Control Center etc. from the Protector Suite QL item in the Programs/All Programs menu. Figure D - 32 Control Center & Biomenu 18. See “Help & Manual” on page D - 49 for further details. 19.
Windows XP Information Fingerprint Control Center Features Application Launcher The Application Launcher allows you to register applications to be launched when assigned to a particular finger. Simply copy the application icon on to one of the registered fingers and ten click OK to close the application window. Once registered the application will launch when you swipe the appropriate finger across the sensor.
Windows XP Information GPS Module If you have included an Global Positioning System (GPS) receiver module in your purchase option, you will need to obtain map software suitable for your global location. Map software programs are both commercially available and downloadable directly from the internet. A Global Positioning System satellite continually transmits high-frequency radio signals containing the time and location of the satellite in relation to the earth.
Windows XP Information Configuring the COM Port for the GPS Module You need to make sure that the COM port for the GPS module is set to COM 3 at a 4800 baud rate. To do this follow the instructions below: 1. 2. 3. 4. 5. 6. 7. Click Start (menu), point to Settings and click Control Panel (or click Control Panel). Double-click System (icon); System (icon) is in Performance and Maintenance (category). Click the Hardware (tab) > Device Manager (button).
Windows XP Information RFID Reader Module If you have included the RFID Reader module in your purchase option, you will need to obtain software suitable for your system. The scanner for the module is located at the top of the computer. •For RFID Reader - Simply hold any RFID enabled card (up to a distance of 2CM) in front of the scanner to obtain a reading.
Windows XP Information Configuring the COM Port for the RFID Reader You need to make sure that the COM port for the RFID reader is set to COM 1 at a 9600 baud rate. To do this follow the instructions below: 1. 2. 3. 4. 5. 6. Click Start (menu), point to Settings and click Control Panel (or click Control Panel). Double-click Device Manager (icon); Device Manager (icon) is in Hardware and Sound (category). Click “+” next to Ports (COM & LPT) if its sub-items are not shown.
Windows XP Information D D - 58
ExpressCard 34 Approved List Appendix E: ExpressCard 34 Approved List The ExpressCards listed in the table below are approved for use with this computer. Please make sure any ExpressCards you use with this computer are included in the list. For further information contact your service center. Model Brand 5-In-1 APIOTEK GIGA-LAN Abocom 32G SSD ExpressCard Transcend 16G SSD ExpressCard Transcend AVerMedia AVerTV DVB-T AVerMedia Brand Luxe 3.
ExpressCard 34 Approved List E E - 2
