V09.1.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The computer is tough, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. the tough magnesium alloy case and shock mounted design will help the computer resist shocks, bumps and small drops but If the computer falls, the case and the components could still be damaged so try and this situation. • • 2. Do not place it on an unstable surface.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. VI •Only use a power adapter approved for use with this computer.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .................................................................................I FCC Statement .............................................................II FCC RF Radiation Exposure Statement: ................... III Instructions for Care and Operation ........................... V Power Safety .............................................................. VI Battery Precautions ...................................................VII Cleaning ....................................
Preface Adding a Printer ...........................................................2-10 USB Printer ..............................................................2-10 Parallel Printer ..........................................................2-10 Power Management Overview ........................................................................3-1 The Power Sources ........................................................3-2 AC/DC Adapter ...........................................................
Preface BIOS Utilities Overview ........................................................................5-1 The Power-On Self Test (POST) ...................................5-2 Failing the POST .........................................................5-3 Fatal Errors .................................................................5-3 Non-Fatal Errors .........................................................5-3 The Setup Program ........................................................5-4 Entering Setup ...
Preface Enabling & Activating TPM ......................................7-7 Initializing TPM ..........................................................7-9 Infineon Security Platform Settings Tool ..................7-12 Fingerprint Reader Module ..........................................7-13 User Enrollment ........................................................7-14 Fingerprint Control Center Features .........................7-18 PC Camera Module ......................................................
Preface Scheme Options .......................................................... B-4 Attaching Other Displays ............................................. B-5 Display Modes .............................................................. B-7 Windows XP Information DVD Regional Codes ................................................... D-2 Windows XP Start Menu & Control Panel ................... D-3 Touchpad and Buttons/Mouse ...................................... D-4 Function Keys & Visual Indicators .....
Preface XVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Introduction This wide screen tough notebook computer provides an ideal platform for mobile computer use with a magnesium alloy case to help provide resistance to shocks, bump and drops, an anti-shock mounting design to protect the hard disk and LCD screen from damage and a spill resistant keyboard (water resistant to100cc) and case design preventing spills (see “What to do if you Spill Liquid on the Computer” on page 6 - 11 for details) from leaking into the sensitive interior.
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the remainder of this User’s Manual. You may also find the notes marked with a of interest to you.
1 Quick Start Guide Not Included Operating Systems (e.g. Windows Vista/Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in Table 4 - 1, on page 4 - 3. Drivers are programs which act as an interface between the computer and a hardware component e.
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the following operating systems are supported.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. Remove all packing materials and place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter. Pull the carrying handle out to easily access the latch.
Quick Start Guide Operating System Setup If you are installing new system software, or are re-configuring your computer for a different system, make sure you configure the appropriate OS setting in the BIOS before installing a new operating system. 1. Start-up the computer and press to enter the BIOS. 2. Go to the Advanced menu, select “Installed O/S” and make sure the appropriate operating system is selected. 3.
1 Quick Start Guide System Map: LCD Panel Open Figure 1 - 3 LCD Panel Open LCD Latch Built-In PC Camera (Optional) 3. LCD 4. Power Button 5. Keyboard 6. Fingerprint Reader Module 7. Touchpad & Buttons 8. Built-In Microphone 9. LED Indicators 10. Carrying Handle Wireless Device Operation Aboard Aircraft 1. 2. 1 2 3 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Quick Start Guide LED Indicators The LED indicators on the computer display helpful information about the current status of the computer.
1 Quick Start Guide Keyboard The keyboard has a numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly (see Figure 1 - 4). See Table 1 - 3, on page 1 - 11 for details of the function/ hot key indicators. Function Keys NumLk & ScrLk Keys Play/Pause Key Numerical Keypad 3.75G Module Power Toggle Key Fn Key Special Characters Some software applications allow the number-keys to be used with Alt to produce special characters.
Quick Start Guide Function Keys & Visual Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators (see the table below) are available when the Hot Key driver is installed (see “” on page 4 - 7). Keys Function/Visual Indicators Keys Function/Visual Indicators Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F7 Display Toggle Fn + _ Fn + F1 Fn + F2 Fn + F3 Fn + F4 Fn +F5/F6 3.
1 Quick Start Guide System Map: Front & Rear Views 1 Figure 1 - 5 Front & Rear Views 1. 2. 3. 4. LCD Latch Carrying Handle Speakers Battery 3 2 3 4 Carrying Handle Pull the carrying handle out to transport the computer, and push it in until it clicks into position for standard desktop use. Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Quick Start Guide System Map: Left View 3 1 2 4 Figure 1 - 6 Left View 5 1. 2. 9 7 6 8 8 10 7-in-1 Card Reader The card reader allows you to use the most popular digital storage card formats: MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) / MS Pro (Memory Stick Pro) / MS Duo (requires PC adapter) / Mini SD (requires PC adapter) / RS MMC (requires PC adapter) DC-In Jack External Monitor Port 3. S/PDIF-Out Jack 4. Microphone-In Jack 5. Headphone-Out Jack 6.
1 Quick Start Guide System Map: Right View Figure 1 - 7 Right View 1. 2. 3. 4. 5. Optical Device Drive Bay (for CD/ DVD Device - see page 2 - 3) 1 * USB 2.0 Port GPS Antenna Socket (for optional GPS Module) Serial (COM1) Port Security Lock Slot 1 2 3 3 4 Changing DVD Regional Codes Disk Eject Warning Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.
Quick Start Guide System Map: Bottom View CPU The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 1. 2. 2 3 3. 5 Overheating To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use. Figure 1 - 8 Bottom View 1 4 4. 4 5. Battery Hard Disk Bay Cover (3.
1 Quick Start Guide Windows Vista Start Menu & Control Panel Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display Settings control panel (in Personalization) in Windows Vista as long as the appropriate Intel video driver is installed. For more detailed video information see “Intel Video Driver Controls” on page B - 1. To access Display Settings in Windows Vista: 1. 2. 3. 4. 5. 6. 7. Click Start, and click Control Panel (or point to Settings and click Control Panel).
1 Quick Start Guide 1 4 2 3 Figure 1 - 10 - Display Properties Desktop Intel Display Mode Description Single Mode One of the connected displays is used as the display device Intel(R) Dual Display Clone Mode Both connected displays output the same view and may be configured independently Extended Desktop Mode Both connected displays are treated as separate devices, and act as a virtual desktop Table 1 - 4 - Display Options 1 - 18 Video Features
Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 16) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
1 Quick Start Guide 1 - 20
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • Hard Disk Drive/Solid State Drive Optical (CD/DVD) Device 7-in-1 Card Reader ExpressCard Slot Touchpad and Buttons/Mouse Audio Features Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive/Solid State Drive The hard disk drive/solid state drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 2). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 16).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 14. .
Features & Components 2 Card Reader Cover Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards). Make sure you install the Card Reader driver (see “Card Reader” on page 4 - 5). ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34.
Features & Components 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. Touchpad and Buttons/Mouse The Touchpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The Touchpad buttons function in much the same way as a two-button mouse.
Features & Components Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon to bring up an audio menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination or On-Screen Menu buttons. Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer).
Features & Components 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. 3 AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack on the left of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle.
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Sleep/Hibernate hotkey button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down). Use Power Options (Hardware and Sound menu) control panel in Windows Vista to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance for maximum performance when the computer is powered from an AC power source.
Power Management 3 Power Button The Power Button in the Start Menu (in Classic View use the Shut Down button ) can be used to send the computer into a powersaving state. Sleep Mode & Mobile PC Battery A mobile PC in Sleep uses very little battery power. After an extended period of time the computer will save any open documents and applications to hard disk. Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. It is recommended that you enable a password on wake up in order to protect your data. However you can disable this setting from the Power Options menu by clicking Require a password on wakeup in the left menu, and selecting the options (click Change settings that are currently unavailable).
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Power Status Icon To Resume Color Power Off Off Press the Power Button Sleep Blinking Green Press the Power Button Closing the Lid If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Power Management 3 Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Please follow these simple guidelines to get the best use out of your battery. Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g.
Power Management Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. • Reduce the amount of time before the display is turned off. • Close wireless, Bluetooth, modem or communication applications when they are not being used.
Power Management Battery Life 3 Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 6 - 3. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 14 for instructions on how to do this).
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Caution Danger of explosion if battery is incorrectly replaced. Damaged Battery Warning Should you notice any physical defects (e.g.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 3 1. 2. 3. Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management 3 How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Drivers (button) to access the optional driver menu. 1. 2. 4 3. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
Drivers & Utilities Driver Name Page # Chipset Page 4 - 5 Video Page 4 - 5 LAN Page 4 - 5 Card Reader Page 4 - 5 Touchpad Page 4 - 5 Trusted Platform Module (TPM) Page 4 - 6 Fingerprint Reader Page 4 - 6 Hot Key Utility Page 4 - 6 PC Camera (Optional) Page 4 - 6 Audio Page 4 - 7 Wireless LAN Module Page 7 - 26 3.
Drivers & Utilities 4 Updating/Reinstalling Individual Drivers User Account Control (Win Vista) If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer).
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Drivers (button) to access the optional driver menu. Driver Installation General Guidelines The driver installation procedures outlined in this Chapter (and in Chapter 7 Options & Modules), are accurate at the time of going to press. Drivers are always subject to upgrade and revision so the exact procedure for certain drivers may differ slightly.
Drivers & Utilities Trusted Platform Module (TPM) 4 Before installing the Trusted Platform Module driver you should enable the TPM State in the BIOS (see “Security Menu” on page 5 - 11 and see “Trusted Platform Module” on page 7 - 7 for full details. 1. Click 6.Install TPM Driver > Yes. 2. Click Install > Next. 3. Click the button to accept the license and click Next. 4. Click Next > Next > Install. 5. Click Finish > Yes to restart the computer. Fingerprint Reader 1. Click 7.FingerPrint > Yes. 2.
Drivers & Utilities Audio 1. Click 10.Install Audio Driver > Yes. 2. Click Next. 3. Click Finish to restart the computer. Note that after installing the audio driver the system will not return to the Drivers Installer screen. To install any of the optional drivers listed overleaf, eject the Device Drivers & Utilities + User’s Manual disc and then reinsert it (or double-click the disc icon in My Computer), and click Option Drivers (button) to access the optional driver menu.
Drivers & Utilities Optional Drivers Bluetooth Module See the pages indicated for the driver installation procedures for any optional modules included in your purchase option. Note: The operating system is the default setting for Bluetooth control in Windows Vista, and does not require a driver. See “Bluetooth Module” on page 7 - 2 for configuration instructions. 4 Wireless LAN Module See the introduction in “Wireless LAN Module” on page 7 - 26, and check the installation procedure. 3.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Phoenix SecureCore(tm) Setup Utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured right is for guideline purposes only. The POST screen on your computer may appear slightly different. If you disable the Boottime Diagnostic Screen, the POST screen will not appear. The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The Phoenix SecureCore(tm) Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu Phoenix SecureCore(tm) Setup Utility Figure 5 - 2 Main Main Advanced Security TPM State Boot Main Menu Item Specific Help System Time: System Date: [22:12:05] [06/10/2009] SATA Port 1 SATA Port 2 [FUJITSU MHY2120BH-(P] [TSSTcorp CDDVDW TS-L] System Memory Extended Memory 632 KB 989 MB BIOS Revision KBC/EC Firmware Revision ******** ******** 5 F1 Esc Help Exit Exit Select Item Select Menu -/+ Enter , , or selects field.
BIOS Utilities SATA Port1/2 (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a HDD/optical Device on the computer’s SATA Port 1 or SATA Port 2. Use the Auto (Type:) setting to have the items configured automatically for you. System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
BIOS Utilities Advanced Menu Phoenix SecureCore(tm) Setup Utility Main A dvanced Advanced Security TPM State Boot Exit Item Specific Help 5 Figure 5 - 3 Advanced Menu SIO ITE8305E Configuration Installed O/S: Legacy USB Support: Boot-time Diagnostic Screen: Legacy OS Boot: Reset Configuration Data: Power On Boot Beep Battery Low Alarm Beep: FAN Control: Power Conserve Mode: F1 Esc Help Exit Select Item Select Menu [Vista] [Enabled] [Disabled] [Enabled] [No] [Disabled] [Enabled] [Automa
BIOS Utilities Installed O/S (Advanced Menu) This setting tells the computer what kind of operating system you’re using. Make sure you choose the correct setting for your O/S in order to prevent system problems. Note: If you select the Vista O/S then the SATA Mode Selection menu will become available. If you are installing the Windows XP O/S make sure you have set the appropriate operating system here in order to prevent system problems.
BIOS Utilities Reset Configuration Data (Advanced Menu) This item is set to No as default. You can change the setting to Yes if you have installed a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot. Power On Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up.
BIOS Utilities Security Menu Phoenix SecureCore(tm) Setup Utility Main Advanced Security Security TPM State Exit Security Menu Item Specific Help The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.
BIOS Utilities Password Warning 5 If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. Set User Password (Security Menu) You can set a password for user mode access to the Phoenix SecureCore (tm) Setup Utility.
BIOS Utilities TPM Support (Security Menu) Enable TPM Support from this menu, and the TPM State menu will then appear (see “TPM State” on page 5 - 14). Note: If you disable TPM Support then your TPM information may be erased altogether. You should only disable TPM support when you need to clear the TPM information. The default setting is “Enabled”. TPM Password Note that you should set a supervisor password in the BIOS to protect the TPM information from being tampered with by unauthorized users.
BIOS Utilities TPM State Menu 5 To access this menu you must first enable TPM support from the security menu (see page 5 - 13).
BIOS Utilities If you have made any changes to the TPM State you will be asked to execute or reject the changes made after you have saved and exited the BIOS. Highlight the required option (it will be white), and then press Enter to save it. Phoenix TrustedCore(tm) Setup Utility Aded Physical Presence operations Figure 5 - 6 Item Specific Help TPM configuration change was requested to State: Clear WARNING!!! Clearing erases information stored on the TPM.
BIOS Utilities Boot Menu Figure 5 - 7 Phoenix SecureCore(tm) Setup Utility Main Advanced Security Boot Exit Boot Menu Item Specific Help Boot priority order: 1: IDE CD: TSSTcorp CDDVDW TS-L633A-( 2: USB CDROM: 3: IDE HDD: FUJITSU MHY2160BH-(PM) 4: PCI BEV: Realtek Boot Agent 5: USB HDD: 6: USB KEY: 7: USB FDC 8: Excluded from boot order: : USB ZIP: : USB LS120: : PCI SCSI: : Other USB: : PCI: 5 F1 Esc Help Exit Select Item Select Menu -/+ Enter Keys used to view or configure devices: Up
BIOS Utilities Exit Menu Figure 5 - 8 Phoenix SecureCore(tm) Setup Utility Main Advanced Security Boot Exit Exit Menu Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Utilities 5 5 - 18
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 .
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 4. 5. Carefully lift the hard disk up at point 4 . Grip the tab 5 and slide the hard disk in the direction of arrow 6 .
Upgrading The Computer 6. 7. Remove the hard disk. Carefully insert the new hard disk and replace all the covers and screws.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Locate the RAM & CPU bay cover and remove screws 1 - 4 . Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 5 , and remove the cover 6 . 1 5 2 6 6 4 Figure 6 - 6 Removing the RAM & CPU Bay Cover 3 Fan Cable Make sure you reconnect the fan cable 5 before screwing down the bay cover.
Upgrading The Computer 5. 6. 7. 8. Remove screws 7 - 9 and use a screwdriver to carefully slide out the optical device at point 10 . Insert the new device and replace the optical device screws 7 - 9 . Reconnect the fan cable before replacing the bay cover ( 5 in Figure 6 - 6 on page 6 - 7). Replace the bay cover and screws.
Upgrading The Computer Upgrading the System Memory (RAM) 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Locate the RAM & CPU bay cover and remove screws 1 - 4 . Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 5 , and remove the cover 6 .
Upgrading The Computer 5. 6. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 7 & 8 ) in Figure 6 - 9. The RAM module will 9 pop-up, and you can remove it. Contact Warning 6 Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. Figure 6 - 9 RAM Module Release Latches 7 7.
Upgrading The Computer What to do if you Spill Liquid on the Computer The keyboard incorporates a drainage system that minimizes the chances of liquid spillages on the keyboard penetrating the inside components of the computer. Liquid spilled on the computer is drained through the drainage hole at the bottom of the computer. There is no guarantee that all water can be prevented from entering the computer, and damage resulting from spillages is not covered in the warranty.
Upgrading The Computer 3. Move the computer to a dry place (while keeping it level) and wipe any liquid off the keyboard using a clean, soft, dry cloth. 4. 5. 6. Wipe any remaining liquid off the bottom of the computer. Remove the battery (see “Removing the Battery” on page 6 - 3). Remove the DVD Drive module (see “Upgrading the Optical (CD/DVD) Device” on page 6 - 7) and wipe any wet parts with a clean, soft, dry cloth. Contact your service center to have the computer examined for any problems.
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • • • • • • Bluetooth Module Security Modules (TPM & Fingerprint) PC Camera Module Wireless LAN Module 3.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Bluetooth Module The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows Vista, and therefore does not require a driver.
Modules & Options Bluetooth Configuration in Windows Vista Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). To Turn the Bluetooth Module On 1. 2. 3. Press the Fn + F12 key combination to power on the Bluetooth module. A Bluetooth icon will appear in the taskbar (see sidebar).
Modules & Options To Add a Bluetooth Device 1. 2. Figure 7 - 2 Add Bluetooth Device Wizard 3. 4. 5. Access the Bluetooth Devices control panel. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. Click Devices (tab), and then click Add. The Add Bluetooth Device Wizard will appear. Click to select “My device is set up and ready to be found”, and then click Next. 6. 7. 8.
Modules & Options To Change Settings for the Bluetooth Device 1. 2. Access the Bluetooth Devices control panel. Click on the device you want to change and click Properties to: • • Change the name of the device (click General, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. Access the Bluetooth Devices control panel.
Modules & Options Password Warning If you set passwords for any of the security modules, NEVER forget your password. 7 The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Modules & Options Trusted Platform Module Before setting up the TPM functions you must initialize the security platform. Enabling & Activating TPM 1. 2. 3. 4. 5. Restart the computer. Enter the PhoenixBIOS Setup Utility by pressing F2 during the POST. Use the arrow keys to select the Security menu. Select TPM Support and set the item to Enabled. The TPM State menu will then appear.
Modules & Options 6. 7. Use the arrow keys to select the TPM State menu. Select TPM State, and set the item to Enable & Activate. Phoenix TrustedCore(tm) Setup Utility Figure 7 - 6 Main Advanced Security TPM State Boot TPM State Exit Item Specific Help Current TPM State: Enabled and Deactivated Change TPM State [No Change Changes TPM State ] No Change Enable & Activate Deactivate & Disable Clear 7 F1 Esc Help Exit 8.
Modules & Options Initializing TPM 1. 2. 3. 4. To initialize the TPM it may be necessary to first clear any existing TPM information if applicable. Enter the PhoenixBIOS Setup Utility by pressing F2 during the POST. Use the arrow keys to select the TPM State menu. Select TPM State, and set the item to Clear.
Modules & Options 7. Run the application from the Infineon Security Platform Solution > Manage Security Platform item in the Start > Programs/All Programs menu. 8. Click User Settings (tab) and click Yes, or right-click the taskbar icon and select Security Platform Initialization (or click the Security Platform State taskbar bubble). 9.
Modules & Options 12. Click Next. 13. Choose the Security Platform Features you want to use by clicking the appropriate tickbox. 14. Enter a Basic User Password (and re-type to confirm it) and click Next. Help Right-click the taskbar icon to bring up the menu to select Help or How to use the Security Platform Features. 7 Figure 7 - 9 Settings 15. 16. 17. 18. 19. Click Next to confirm the settings. The computer will then initialize the settings. Click Finish.
Modules & Options Help Right-click the taskbar icon to bring up the menu to select Help or How to use the Security Platform Features. 7 Infineon Security Platform Settings Tool The Infineon Security Platform Settings Tool allows you to manage and check the TPM state, manage your password information, and to backup and restore the TPM data. As TPM is usually administered within large enterprises and organizations, your system administrator will need to assist you in managing the information here.
Modules & Options Fingerprint Reader Module The fingerprint reader module provides a high level of security for your computer. Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. Before beginning the enrollment process it is recommended that you go through the fingerprint tutorial. To run the tutorial click Start > Programs/All Programs > Protector Suite QL > Fingerprint Tutorial after installing the driver.
Modules & Options User Enrollment 1. Fingerprint Enrollment 2. Note that it is strongly recommended that you enroll more than one finger in case of injury etc. 3. 4. 5. Click Start > Programs/All Programs > Protector Suite > Control Center, or double click the taskbar icon (click Initialize). On the first run of the program you will be asked to click the Accept button to accept the license.
Modules & Options 6. Click the button above any of the fingers to begin the enrollment process for that finger. 7. Swipe the finger until the progress bar reaches 100% to enroll that finger. 8. Repeat the process for all the fingers you wish to enroll (see sidebar), and then click Save and Continue. 9. Enter a backup password and click Apply. 10. Close the fingerprint status window. Fingerprint Enrollment Note that it is strongly recommended that you enroll more than one finger in case of injury etc.
Modules & Options 11. Right-click the taskbar icon and select Start Control Center (and then swipe a finger) to allow you to Edit Fingerprints, register Applications, edit Settings and access the Help menu etc. You can also run the Control Center etc. from the Protector Suite item in the Programs/All Programs menu 12. Click “Help” in Control Center Home to get more information on any topic. 13. You can also run the Tutorial, or Product Tour video to get more information.
Modules & Options Protector 2009 TPM Initialization 1. 2. 3. 4. 5. 6. 7. Click Start > Programs/All Programs > Protector Suite > Control Center, or double click the taskbar icon . Swipe a registered finger or enter the password. Click Advanced Settings (Control Center Home > Settings). Click Trusted Platform Module (TPM). Click Initialize. Click Identity and then click Mulifactor to configure fingerprint authentication along with TPM. Select the method required and click Apply.
Modules & Options Fingerprint Control Center Features Help For more information on these and other features simply access “Help” in the Fingerprint Control Center and select the item from the menu on the left. 7 Application Launcher The Application Launcher allows you to register applications to be launched when assigned to a particular finger. Simply copy the application icon on to one of the registered fingers and ten click OK to close the application window.
Modules & Options PC Camera Module The PC Camera module uses the BisonCap application to capture video files and to take pictures. Before installing the driver, make sure that the optional PC Camera is on. Before installing the PC Camera driver, make sure that the optional PC Camera is on. Use the Fn + F10 key combination (see “Function Keys & Visual Indicators” on page 1 - 11) to toggle power to the PC Camera module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 7 Click Start, and click Control Panel (or point to Settings and click Control Panel). 2. Click Sound (Hardware and Sound). 3. Click Recording (tab). 4. Right-click Microphone (Realtek High Definition Audio) and make sure the item is not disabled. 5. Double-click Microphone (or select Properties from the right-click menu). 6.
Modules & Options Figure 7 - 15 Audio Setup for PC Camera Right-click 7 PC Camera Module 7 - 21
Modules & Options Pre-Allocating File Space You may pre-allocate the file size (File > Allocate File Space) for the capture file in the BisonCap program. 7 Pre-allocating space on the hard disk can improve the capture quality (particularly of large capture files), by reducing the amount of work the hard disk has to do in finding space for the video data as it is being captured. See also “Reducing Video File Size” on page 7 - 23.
Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules & Options Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the BisonCap program. Go to Options and scroll down to select Video Capture Filter.... Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Modules & Options Zoom The BisonCap program allows you to zoom the camera in and out. 1. 2. Run the BisonCap program. Go to Zoom and select Zoom Out/Zoom In. Figure 7 - 17 Zoom/Setting Taking Still Pictures The BisonCap program allows you to take still pictures. 1. 2. 3. Run the BisonCap program. Go to Options and select Take Picture. The picture (in JPEG format) will be placed in the Snapshot folder desktop. Snapshot Folder on the The Snapshot folder’s default location is on the desktop.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + F11 key combination/ button to toggle power to the WLAN module, and check the indicator to see if the module is powered on or not (see Table 1 - 3, on page 1 - 11/ Table 1 - 2, on page 1 - 9).
Modules & Options 802.11 b/g WLAN Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 1.Wireless Lan > Yes. 4. Choose the language you prefer and click Next. 5. Click Next > Install. 6. Click Finish to complete the installation. 7. The operating system is the default setting for Wireless LAN control in Windows Vista (see overleaf).
Modules & Options Connecting to a Wireless Network Make sure the Wireless LAN module is turned on. 1. Click the taskbar wireless icon , and then click Connect to a network (or rightclick the icon , and then click Connect to a network). Figure 7 - 18 Taskbar Menus Click icon Right-click icon 7 Network and Sharing Center 2. 3. In the Show list, click to choose Wireless from the drop-down menu. A list of currently available networks will appear.
Modules & Options 4. 5. Click a network, and then click Connect. If you do not see a network you want to connect to, click Set up a connection or network (a list of options will appear allowing manual searching, and creating a new network). Figure 7 - 20 Connecting 7 6. Move the cursor over the taskbar icon to see the connection status (see below).
Modules & Options 7. Security Enabled Networks To disconnect from the wireless network you can click the taskbar wireless icon , and then select Connect or disconnect to access the network menu, and click Disconnect (or right-click the icon , and then click Disconnect from). You should try to make sure that any network you are connecting to is a secure network. 7 Click icon Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Intel® My WiFi Installation & Configuration Intel® My WiFi Technology uses your WLAN module to allow you to connect up to eight other WiFi enabled devices (e.g. digital cameras, other computers, cell phones, handheld devices etc.) to your computer (similar to Bluetooth), while still connecting to the Internet through your WiFi wireless connection. Intel® My WiFi Technology offers greater range and speed than other personal area networks, and does not require an access point.
Modules & Options Intel® Wi-Fi Link 5100/5300 Series My WiFi Driver Installation 7 If you see the message “Found New Hardware” click Cancel to close the window. Intel(R) PROSet/ Wireless 1. Make sure the module is powered on, then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 1.Wireless Lan > Yes. 4. Click Next > Next. 5. Click the button to accept the license and click Next > Next. 6.
Modules & Options Intel® My WiFi Configuration You can configure the My WiFi settings as follows. 1. 2. Access the Intel® My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by clicking the taskbar icon . Click Enable (on the first run of the program there will be no connected devices listed).
Modules & Options 3. 4. 5. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Network and Sharing Center (Network and Internet). Click Manage Network Connections. Click Manage Network Connections Figure 7 - 25 Network and Sharing Center 7 6. Right-click Intel My WiFi STA (Station) in Network Connections and select Properties. Figure 7 - 26 Intel My WiFi STA Properties (Network Connections) Right-click Intel My WiFi STA (Station) and select Properties.
Modules & Options 7. 8. 9. Click Sharing (tab) and select “Allow other network users to connect through this computer’s Internet connection”. Select Intel My WiFi PAN under Home Networking Connection. Click OK. Click “Allow other network users to connect through this computer’s Internet connection”. Select Intel My WiFi PAN.
Modules & Options Figure 7 - 28 IP Address Warning 10. A message will appear to inform you that the LAN adapter will be set to use the IP address 192.168.0.1. 11. Click Yes to enable Internet Connection Sharing. IP Addresses 7 The Intel® My WiFi default gateway IP address is 192.168.0.1. DO NOT use this address for any Wireless Access Point (or any other static IP address on your network). 12.
Modules & Options 14. Click Profiles, click Intel Wireless PAN and click Edit. Figure 7 - 30 IP Address Warning 15. You can change the Profile Name and Network Name to your personal preferences in General (tab). 7 Profile and Network Names The Profile Name is the name as displayed on your computer in the Network Connections control panel (see Figure 7 - 26 on page 7 34).
Modules & Options 16. 17. 18. 19. 7 Click Security (tab). Change the Security Type to WEP and the Encryption Type to 64bit. Enter a password (5 characters long) in the Passphrase box. Click OK.
Modules & Options 20. Click Sharing (tab). 21. Make sure Filter Network Traffic and DHCP and DNS Server are Disabled. 22. Click OK. Set Filter Network Traffic & DHCP and DNS Servers to Disabled.
Modules & Options 23. Click Advanced (tab). 24. Make sure the Default Channel is set to Channel 1, 6 or 11. 25. Click OK.
Modules & Options 26. Double-click Intel My WiFi PAN (Personal Area Network) in Network Connections. 27. Click Details to display the Network Connection Details.
Modules & Options 28. Access the Intel® My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by clicking the taskbar icon . 29. To add a new device follow the instructions in the devices’ user guide for connecting to a WiFi network. 30. Click Add New Device in Intel® My WiFi Utility to confirm the security settings detail.
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules & Options 3.75G/HSPA Module Options 7 There are three optional 3.75G/HSPA modules available for this series of computer models. Each module is supplied with the appropriate application software. The module type supplied may depend upon the computer model purchased. Check with your service center for details. 3.75G/HSPA Module If you have included an optional 3.
Modules & Options Before installing the application, make sure that the 3.75G/HSPA module is ON (installing the driver with the module off will not allow the software to detect the module hardware correctly). Use the Fn + key combination (see Table 1 - 5, on page 1 - 15) to toggle power to the 3.75G/HSPA module. When the 3.75G/HSPA module is powered on, the indicator will briefly be displayed. Note that exiting the application does NOT turn off the 3.75G/HSPA module.
Modules & Options USIM Card Installation Power Safety Warning 7 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 . Before you undertake any installation procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines).
Modules & Options 5. Insert the USIM card as illustrated below until it clicks fully into position, and replace the battery. Figure 7 - 39 USIM Card Insertion 7 3.
Modules & Options 3G Watcher Application Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + key combination to toggle power to the 3.75G/HSPA module, and check the indicator to see if the module is powered on or not (see Table 1 - 3, on page 1 - 11/ Table 1 - 2, on page 1 - 9). With the 3.
Modules & Options Setting Up a Carrier Profile Although the connection information is stored on the USIM card supplied by the service provider, you may need to set up the appropriate carrier profile in 3G Watcher. 1. 2. 3. 4. Power on the 3.75G/HSPA module using the Fn + key combination. Access the 3G Watcher application from the Start menu (Start > Programs/All Programs > Sierra Wireless > 3G Watcher), or by double-clicking the desktop icon . Click Tools and select Options.
Modules & Options 5. Figure 7 - 41 You can then enter a new profile name or choose a profile from the drop-down list provided by the software (see the sidebars for information on the profile details).
Modules & Options Connecting to the Service Provider 1. 2. 3. Power on the 3.75G/HSPA module using the Fn + key combination. You can access the 3G Watcher application from the Start menu (Start > Programs/All Programs > Sierra Wireless > 3G Watcher), or by double-clicking the desktop icon . The software will run and display the service provider name (see “Setting Up a Carrier Profile” on page 7 - 49). Figure 7 - 43 Connect Button 7 4. 5. Click Connect to begin the connection process.
Modules & Options 6. When the connection is successful a taskbar notification will appear (as below). 7. You can then access the internet, download e-mail etc. as per any internet connection. While you are connected the taskbar icon will be green (it will be red when the program is running but not connected). To disconnect click the Disconnect icon. Figure 7 - 45 Connected Taskbar Notification 8. 7 9. Figure 7 - 46 3GWatcher Connected 10. The program will disconnect from the service provider. 11.
Modules & Options 12. If you click the 3G Watcher close icon to click OK to confirm the program exit. a message will be displayed asking you Figure 7 - 47 Exit Warning 7 13. Exiting the program DOES NOT turn off the 3.75G/HSPA module, and you will need to press the Fn + key combination to turn off the module (pay careful attention to this aboard aircraft - see “Wireless Device Operation Aboard Aircraft” on page 7 - 48). 14.
Modules & Options Short Messaging Service In addition to standard internet services you may also send and receive SMS text messages using the 3G Watcher program, if your service supports SMS. Reading SMS Messages 1. 2. 3. 4. 7 The SMS message indicator in the main window will notify you of any new messages received. Double-click the icon or select Tools > SMS Express. Select the inbox folder and select any message to read it.
Modules & Options HSPA Modem With the 3.75G/HSPA modem module and USIM card (supplied by your service provider) installed you may then install the HSPA modem interface. The HSPA modem interface application allows you to directly access your HSPA internet service from the computer. HSPA Modem Interface Installation 1. Enable power to the module by pressing the Fn + key combination (the on screen icon will indicate the module’s power status). 2. If a Found New Hardware window appears, click Cancel. 3.
Modules & Options HSPA Modem Interface HSPA Modem Help To get help on HSPA modem configuration and settings, click the help icon and select Help. The connection information is stored on the USIM card supplied by the service provider. 1. 2. 3. 4. 7 5. Power on the 3.75G/HSPA modem module using the Fn + key combination. Access the HSPA Modem interface from the Start menu (Start > Programs/All Programs > HSPA Modem > HSPA Modem), or by double-clicking the desktop icon .
Modules & Options 6. Click Connect to connect to your service provider. Figure 7 - 49 Connecting to Network 7. The message “Network is connected” will be displayed when the network connection is successful. Figure 7 - 50 Network is Connected 8. You can then access the internet, download e-mail etc. as per any internet connection. 3.
Modules & Options 9. Figure 7 - 51 While you are connected the upper right corner of the HSPA Modem interface will display the upload and download rates, and the taskbar icon will display the connection speed. Uploading/ Downloading Rates and Speed 10. To disconnect click the Disconnect icon (Connection Manager). 11. The program will disconnect from the service provider. 12. The module will still be on, and you will need to press the Fn + key combination to turn it off. Adding a Profile 1. 7 2.
Modules & Options 3. 4. Click Add (button) and input any Network Settings required by your service provider. Click OK to save the profile. Figure 7 - 53 Network Settings & Profiles 7 5. 6. You can Edit or Delete profiles from the Profiles tab. To use a profile click to select it, and then click Apply (button) and the settings will be transferred to Connection Manager. 3.
Modules & Options Contacts 1. 2. Access the HSPA Modem interface from the Start menu (Start > Programs/All Programs > HSPA Modem > HSPA Modem), or by clicking the desktop icon. Click Contacts (button). Figure 7 - 54 Network Settings & Profiles 7 3. 4. 5. 6. Click Refresh (button) to download the contacts from the USIM card to the computer. The Contacts will then be displayed. Double-click any contact to edit the information (or right-click and select Edit).
Modules & Options Messages 1. 2. Access the HSPA Modem interface from the Start menu (Start > Programs/All Programs > HSPA Modem > HSPA Modem), or by clicking the desktop icon. Click Messages (button). SMS Service In addition to standard internet services you may also send and receive SMS text messages using the HSPA Modem interface, if your service supports SMS. 7 Figure 7 - 55 Network Settings & Profiles 3. 4. 5. Click Refresh (button) to download the messages from the USIM card to the computer.
Modules & Options 6. 7. 8. Click to select a contact from the list and then click Add (button) and the phone number will automatically be added to the recipient field. Type the message information into the message body and click Send (button) to send it, or Save to draft (button) to save the message. Select any message to forward or delete it, or to reply to it. Settings 1. 2.
Modules & Options 3. 4. 5. Click OK alongside any of the options to configure the settings. The Network can be configured for an Automatic (usually from the USIM card) or Manual connection. The Network Mode can be configured for any appropriate mode required. Figure 7 - 57 Settings - Network/ Network Mode 6. 7. 8. You can also change your settings for the Pin #, and input your phone number. Exiting the program DOES NOT turn off the 3.
Modules & Options Mobile Partner Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + key combination to toggle power to the 3.75G/HSPA module, and check the indicator to see if the module is powered on or not (see Table 1 - 3, on page 1 - 11/ Table 1 - 2, on page 1 - 9). With the 3.
Modules & Options Mobile Partner Application You will need to contact your service provider to obtain the exact details of how exactly to configure the settings on this page. Profile Management 1. 2. 3. 4. 5. Power on the 3.75G/HSPA module using the Fn + key combination. Access the Mobile Partner application from the Start menu (Start > Programs/ All Programs > Mobile Partner), or by double-clicking the Mobile Partner icon on the desktop .
Modules & Options Connecting to the Service Provider 1. 2. 3. 4. Power on the 3.75G/HSPA module using the Fn + key combination. Access the Mobile Partner application from the Start menu (Start > Programs/ All Programs > Mobile Partner), or by double-clicking the Mobile Partner icon on the desktop . The software will run and you can select the Profile Name from the menu. Click Connect to begin the connection process. 5. The Mobile Partner application will then display the connection information.
Modules & Options 6. When the connection is successful you can move the cursor over the network icon in the taskbar to display the connection information. Figure 7 - 61 Connected Taskbar Notification 7. 8. 9. You can then access the internet, download e-mail etc. as per any internet connection. While you are connected the indicators in the Mobile Partner window will display uploading and downloading icons and a network icon in the taskbar . To disconnect click the Disconnect and select Disconnect.
Modules & Options 11. The module will still be on, and you will need to press the Fn + key combination to turn it off. 12. If you click the Mobile Partner close icon a message will be displayed asking you to click OK to confirm the program exit and to terminate the connection. Figure 7 - 63 Exit Prompt 7 13. Exiting the program terminates the connection, but DOES NOT turn off the 3.
Modules & Options GPS Module If you have included an Global Positioning System (GPS) receiver module in your purchase option, you will need to obtain map software suitable for your global location. Map software programs are both commercially available and downloadable directly from the internet. A Global Positioning System satellite continually transmits high-frequency radio signals containing the time and location of the satellite in relation to the earth.
Modules & Options 7 7 - 70
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 9) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator , is blinking orange. Low Battery. Plug in the DC power source.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 15). Make sure you’re using the correct adapter.
Troubleshooting Problem You forget password. the Possible Cause - Solution boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Unwelcome numbers appear when typing. Possible Cause - Solution If the LED is lit, then Num Lock is turned ON (see “LED Indicators” on page 1 - 9). Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work. 8 The system freezes or the screen goes dark.
Troubleshooting ? Problem Possible Cause - Solution The PC Camera module cannot be detected. The module is off. Press the Fn + F10 key combination in order to enable the module (see “Function Keys & Visual Indicators” on page 1 - 11). Run the camera program to view the camera picture. The Wireless LAN/ PC Camera/3.75G modules cannot be configured. The driver(s) for the module(s) have not been installed.
Troubleshooting Problem Possible Cause - Solution The Hibernate function has disappeared. You have a computer with 4GB of RAM and have installed Windows Vista Service Pack 1. This is a known issue if your computer has 4GB of RAM and is running Windows Vista Service Pack 1. To re-enable Hibernate mode go to the Command Prompt and type the command “powercfg -h on” (make sure you are logged on as an Administrator): 1. 2. 3. 4. 5. 6. Click Start (menu button). Type “cmd” in the Start Search box .
Troubleshooting Screen Resolution Error If you are experiencing either screen resolution reduction, or screen flickering after resuming from Sleep in Windows Vista only then follow the instructions below to fix this problem. This error arises in compliance with Windows Vista policy, which triggers TMM (Transient Multi-Monitor Manager) when the notebook lid (S3) is closed. TMM disconnects the LCD display from the OS and then adds the LCD display back when the lid is opened.
Troubleshooting 3. 4. 5. Double-click Task Scheduler Library > Microsoft > Windows. Click MobilePC to open the control panel. Right-click TMM and select Disable. 8 Figure 8 - 2 - TMM Disable 6. Close all the control panels.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
Interface (Ports & Jacks) Item Description Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. Serial (COM1) Port The serial communication port allows you to connect various RS232 supported devices to the computer. Serial ports are still used in legacy applications e.g. industrial automation systems.
Interface (Ports & Jacks) A A - 4
Intel Video Driver Controls Appendix B: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 17. DVMT Notes Intel Video Driver Installation Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Video 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Install Drivers. 3. Click 2.Install Video Driver > Yes. 4. Click Next > Yes > Next > Next. 5.
Intel Video Driver Controls Taskbar Icon The Intel GMA control panel can also be accessed by clicking the icon in the taskbar and selecting Graphics Properties from the menu. Intel Graphics Properties More advanced video configuration options are provided by the Intel(R) Graphics Media Accelerator Driver for Mobile. 1. 2. Open the Display Settings control panel (see “Video Features” on page 1 - 17) and click Advanced Settings (button). Click the Intel(R)... tab and click Graphics Properties (button).
Intel Video Driver Controls You may make changes to the devices, color, schemes, Hot Keys etc. by clicking the appropriate menu item or button. Help Menus Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu. Operating Mode At least one other display must be attached in order to view Display Selection options.
Intel Video Driver Controls Application.exe You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application rightclick its shortcut on the desktop click Properties. Click the Shortcut (tab) and see where the executable file is located by clicking the Find Target (button). Note the location and you will then be able to browse to this file.
Intel Video Driver Controls Attaching Other Displays Besides the built-in LCD, you can also use an external monitor/flat panel display, connected to the external monitor port at the rear of the computer, as your display device. The following are the display options: 1. 2. The built-in LCD OR an external monitor/flat panel display connected to the external monitor port (Single Display). The built-in LCD AND an external monitor/flat panel display connected to the external monitor port (Multiple Display).
Intel Video Driver Controls Configuring from Intel® GMA Driver for Mobile 1. Operating Mode 2. 3. At least one other display must be attached in order to view Display Selection options. Go to the Intel Graphics Properties control panel (see “Intel Graphics Properties” on page B - 2) and click Display Devices. Click to choose the display option from the Operating Mode menu. Click Apply (and OK to confirm the settings change) and OK (button).
Intel Video Driver Controls Display Modes Single Display Only one of your attached displays is used. Intel(R) Dual Display Clone (mirrored) This mode will drive multiple displays with the same content. Each device may be configured independently for different resolutions, refresh rates, color quality etc. Use this feature to display the screen through a projector for a presentation.
Intel Video Driver Controls To Enable Intel(R) Dual Display Clone 1. 2. 3. 4. 5. Figure B - 6 Display Devices & Settings B B - 8 Display Modes Attach your external monitor to the external monitor port, and turn it on. Go to the Intel Graphics Properties control panel (see “Intel Graphics Properties” on page B - 2) and click Display Devices. Click to choose Intel(R) Dual Display Clone (Operating Mode). Click Apply, and OK to confirm the settings change.
Intel Video Driver Controls To Enable Extended Desktop 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port, and turn it on. Go to the Intel Graphics Properties control panel (see “Intel Graphics Properties” on page B - 2) and click Display Devices. Click to choose Extended Desktop (Operating Mode). Click Apply, and OK to confirm the settings change. Click Display Settings to adjust the settings for the attached devices.
Intel Video Driver Controls Using Windows Vista to Enable Extended Mode Display Settings Extended Desktop Use the control panel to drag the monitors to match the physical arrangement you wish to use. 1. 2. 3. 4. 5. You can drag any icons or windows across to either display desktop, which makes it possible to have one program visible in one of the displays, and a different program visible in the other display.
Intel Video Driver Controls Using Display Settings to Enable Extended Mode 1. 2. 3. Attach your external display to the external monitor port, and turn it on. Open the Display Settings control panel (see “Video Features” on page 1 - 17). Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend my Windows desktop onto this monitor.” and click Apply. Click the appropriate monitor icon (e.g. 2 ) to be able to select the option to extend the desktop on to it.
Intel Video Driver Controls TV Wizard Use the TV Wizard to configure the external display settings either manually or automatically. The wizard will take you though any necessary steps in order to configure the optimal video settings e.g HDTV Format, Display Size and Position etc.
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.
Specifications Processor Memory Storage Intel® Core™2 Duo Processor ULV: SU9300 (1.20GHz) 45nm (45 Nanometer) Process Technology, 3MB L2 Cache & 800MHz FSB - TDP 10W, BGA Socket P Pin-Out, 22 * 22mm CPU On Board 64-bit Wide DDRII (DDR2) Data Channel Supporting Dual Channel DDRII (DDR2) SDRAM One 200 Pin SO-DIMM Socket Supporting DDRII (DDR2) 800MHz Memory Expandable up to 2GB One Changeable 12.7mm(h) Super Multi Optical Device Drive - SATA interface Intel® Celeron® Processor ULV: 723 (1.
Specifications Interface Communication Power Management Three USB 2.0 Ports One Serial (COM1) Port One External Monitor Port One Headphone-Out Jack One Microphone-In Jack One S/PDIF-Out Jack One RJ-45 LAN Jack for 10/100/1000Mb Fast Ethernet One DC-In Jack Built-In 10M/100M/100M Base-TX Ethernet LAN Bluetooth 2.1 + EDR (Enhanced Data Rate) Module (Factory Option) Intel® WiFi Link 5300 Series (3*3 802.
Specifications Environmental Spec Optional Temperature Operating: Non-Operating: Relative Humidity Operating: Non-Operating: Super Multi Optical Device Drive 5°C - 35°C -20°C - 60°C 20% - 80% 10% - 90% Dimensions & Weight 317mm (w) * 229mm (d) * 35mm (h) 2.0 kg (full system with 1G RAM, 2.5” HDD, ODD and 4 Cell Battery) Intel® WiFi Link 5300 Series (3*3 802.11a/g/n) Wireless LAN PCIe interface Half Mini-Card Module Intel® WiFi Link 5100 Series (1*2 802.
Windows XP Information Appendix D: Windows XP Information This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows XP OS.
Windows XP Information DVD Regional Codes Changing DVD Regional Codes Go to the Control Panel and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialogue box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code. DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times.
Windows XP Information Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Windows XP Information Touchpad and Buttons/Mouse The Touchpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The Touchpad buttons function in much the same way as a two-button mouse. Once you have installed the Touchpad driver (see “Touchpad” on page D - 31) you can configure the functions by double-clicking the Touchpad driver icon on the taskbar.
Windows XP Information Function Keys & Visual Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators (see the table below) are available when the hot key driver is installed (see “Module Drivers” on page D - 33). Keys Function/Visual Indicators Keys Function/Visual Indicators Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F7 Display Toggle Fn + _ 3.
Windows XP Information Audio Features You can configure the audio options on your computer from the Sounds and Audio Devices Windows control panel, or from the Realtek HD Audio Manager icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration menus). The volume may also be adjusted by means of the Fn + F5/F6 key combination.
Windows XP Information Video Features You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate Intel video driver is installed. To access Display Properties in Windows: 1. 2. 3. 4. 5. 6. 7. Click Start, point to Settings and click Control Panel (or just click Control Panel). Double-click Display (icon) - In the Appearances and Themes category. Click Settings (tab) in the Display Properties dialog box.
Windows XP Information Display Properties Taskbar Icon The Intel GMA control panel can also be accessed by clicking the icon in the taskbar and selecting Graphics Properties from the menu. 1 2 If you cannot see the tray icon click the “Show Tray Icon” tickbox in the Intel(R) Graphics Media Accelerator for Mobile tab.
Windows XP Information Intel GMA Driver Controls Access the Intel GMA control panel as indicated on page D - 7. You may make changes to the Display Devices, Display Settings, Color Correction, Hot Keys etc. by clicking the appropriate menu item. Help Menus Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu. Operating Mode At least one other display must be attached in order to view Display Selection options.
Windows XP Information Application.exe You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application rightclick its shortcut on the desktop click Properties. Click the Shortcut (tab) and see where the executable file is located by clicking the Find Target (button). Note the location and you will then be able to browse to this file.
Windows XP Information Display Devices & Options Besides the built-in LCD you can also use an external monitor/flat panel display connected to the external monitor port as your display device.
Windows XP Information Attaching Other Displays (Intel GMA) 1. 2. 3. 4. 5. Attach your external display to the external monitor port and turn it on. Go to the Intel GMA control panel and click Display Devices. Click to choose the display option from the Operating Mode menu. Click to choose the display selection from the Display Selection menu. Click Apply, and OK to confirm the settings change.
Windows XP Information To Enable Intel(R) Dual Display Clone (Intel GMA) 1. 2. 3. 4. 5. 6. Attach your external display to the external monitor port and turn it on. Go to the Intel GMA control panel and click Display Devices. Click to choose Intel(R) Dual Display Clone from the Operating Mode menu. Choose which device is to be the Primary Device from the Display Selection menu. Click Apply, and OK to confirm the settings change. Click Display Settings to adjust the settings for the attached devices.
Windows XP Information To Enable Extended Desktop (Intel GMA) 1. 2. 3. 4. 5. 6. Attach your external display to the external monitor port and turn it on. Go to the Intel GMA control panel and click Display Devices. Click to choose Extended Desktop from the Operating Mode menu. Choose which device is to be the Primary Device from the Display Selection menu. Click Apply, and OK to confirm the settings change. Click Display Settings to adjust the settings for the attached devices.
Windows XP Information To Enable Extended Desktop (Windows Display Properties) 1. 2. 3. 4. 5. Attach your external display to the external monitor port and turn it on. Click Start, point to Settings (or click Control Panel) and click Control Panel (if you are in Category View choose Appearance and Themes). Double-click Display (icon). In the Display Properties dialog box, click Settings (tab). Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend my Windows desktop onto this monitor.
Windows XP Information OS Note Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system. (Note: All pictures used on the following pages are from the Windows XP OS.) Power Management Features To conserve power, especially when using the battery, your computer uses the ACPI power management system.
Windows XP Information The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack on the left of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle.
Windows XP Information Shutdown Note that you should always shut your computer down by choosing the Turn Off Computer command from the Start menu in Windows. This will help prevent hard disk or system problems. Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.
Windows XP Information Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes. You can also adjust the settings for each scheme to set the monitor to turn off after a specified time, and the computer's hard disk motor to turn off if the hard disk drive has not been accessed for a specified period of time (if the system reads or writes data, the hard disk motor will be turned back on).
Windows XP Information Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Windows XP Information System Power Options You can use the system power options to stop the computer’s operation and restart where you left off. This system features Stand by and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - see “Hibernate” on page D - 22). Hibernate Mode vs. Shutdown Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to turn it on.
Windows XP Information Stand by System Resume The system can resume from Stand by mode by: • Pressing the power button • Pressing the Sleep/ Resume key combination • Network card (Wake On LAN) activity (if enabled) Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory.
Windows XP Information Configuring the Power Button The power button may be set to send the computer in to either Stand by or Hibernate mode. In Stand by mode, the LED will blink green. In Hibernate mode the LED will be off (battery) or orange (AC/DC adapter). If you are in a power saving mode set to save power through individual components (e.g. hard disk, monitor), the LED will remain green. Sleep Button You may also configure the Sleep/Resume key combination (Fn + F4) from the menu illustrated.
Windows XP Information Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Please follow these simple guidelines to get the best use out of your battery. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page D - 27 for instructions on how to do this).
Windows XP Information Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you need to remove the battery for any reason, see “Removing the Battery” on page 6 - 3.
Windows XP Information Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Windows XP Information Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer by yourself even when you see a message that indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
Windows XP Information Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc, click Install Drivers/Option Drivers (button) and then click the appropriate driver name from the Drivers Installer menu. Follow the instructions to install the driver. 1. Check the driver installation order from Table D - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below. 2.
Windows XP Information WinXP SP3 Driver Page # Chipset Page D - 30 Video Page D - 30 LAN Page D - 30 CardReader Page D - 30 Touchpad Page D - 31 Trusted Platform Module (TPM) Page D - 31 Hot Key Utility Page D - 31 PC Camera (Optional) Page D - 31 Wireless LAN Module (Optional) Page D - 32 Audio Page D - 33 Fingerprint Reader Module Page D - 47 3.
Windows XP Information Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Drivers (button) to access the optional driver menu. Windows XP Service Pack 3 Make sure you install Windows XP Service Pack 3 (or a Windows XP version which includes Service Pack 3) before installing any drivers.
Windows XP Information Touchpad 1. Click 5.Install Touchpad Driver > Yes. 2. Click Next > Next > Next. 3. Click Finish to restart the computer. Hot Key Utility 1. Click 7.Install Hotkey Utility > Yes. 2. Click Next > Install. 3. Click Finish > Finish to restart the computer.
Windows XP Information Wireless LAN Module (Optional) If you have included an Intel® Wi-Fi Link 5100/5300 Series (802.11 a/g/n) or 802.11b/g WLAN module in your purchase option, use the Fn + F11 key combination to toggle power to the module. Your installation procedure will be dependent upon which WLAN module is included in your purchase option. See “WLAN Module” on page D - 59 for details. D Intel Wireless LAN Module 1. Click 9.Wireless Lan > Yes (if SP3 is installed go straight to step 9). 2.
Windows XP Information Audio 1. Click 10.Install Audio Driver > Yes. 2. Click Next. 3. Click Finish to restart the computer. Module Drivers See the following pages for the driver installation procedures for any of the optional modules included in your purchase configuration. Note that after installing the audio driver the system will not return to the Drivers Installer screen.
Windows XP Information Bluetooth Module Note: The operating system is the default setting for Bluetooth control in Windows XP, and does not require a driver. See “Bluetooth Module” on page D 35 for configuration instructions. Fingerprint Reader Module Wireless LAN, Bluetooth & 3.75G Modules Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Windows XP Information Bluetooth Module The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows XP, and therefore does not require a driver. Use the Fn + F12 key combination (see “Function Keys & Visual Indicators” on page D - 5). Bluetooth Data Transfer Note that transferring data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported).
Windows XP Information Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Bluetooth Local Area Connection Icon If you want to display the Local Area Connection icon for the Bluetooth connection in the taskbar, set it up as follows: 1.
Windows XP Information Bluetooth Configuration in Windows XP Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). Bluetooth Taskbar Icon To Turn the Bluetooth Module On 1. 2. 3. Press the Fn + F12 key combination to power on the Bluetooth module. A Bluetooth icon will appear in the taskbar (see sidebar).
Windows XP Information To Add a Bluetooth Device Figure D - 22 1. Access the Bluetooth Devices control panel. 2. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. 3. Click Devices (tab), and then click Add. 4. The Add Bluetooth Device Wizard will appear. 5. Click to select “My device is set up and ready to be found”, and then click Next.
Windows XP Information To Change Settings for the Bluetooth Device 1. 2. Access the Bluetooth Devices control panel. Click on the device you want to change and click Properties to: • • Change the name of the device (click General, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. Access the Bluetooth Devices control panel.
Windows XP Information Password Warning If you set passwords for any of the security modules, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Windows XP Information Trusted Platform Module Before setting up the TPM functions you must initialize the security platform. Enabling & Activating TPM 1. 2. 3. 4. 5. Restart the computer. Enter the PhoenixBIOS Setup Utility by pressing F2 during the POST. Use the arrow keys to select the Security menu. Select TPM Support and set the item to Enabled. The TPM State menu will then appear.
Windows XP Information 6. Use the arrow keys to select the TPM State menu. 7. Select TPM State, and set the item to Enable & Activate.
Windows XP Information Initializing TPM 1. 2. 3. 4. To initialize the TPM it may be necessary to first clear any existing TPM information if applicable. Enter the PhoenixBIOS Setup Utility by pressing F2 during the POST. Use the arrow keys to select the TPM State menu. Select TPM State, and set the item to Clear.
Windows XP Information 7. Run the application from the Infineon Security Platform Solution > Manage Security Platform item in the Start > Programs/All Programs menu. 8. Click User Settings (tab) and click Yes (or click the Security Platform State taskbar bubble). 9. The Quick Initialization method will automatically be selected for you (if you need to use advanced settings provided by your network administrator then select Advanced Initialization) 10. You will need to use a removable media (e.g.
Windows XP Information 12. Click Next. 13. Choose the Security Platform Features you want to use by clicking the appropriate tickbox. 14. Enter a Basic User Password (and re-type to confirm it) and click Next. Help Right-click the taskbar icon to bring up the menu to select Help or How to use the Security Platform Features. Figure D - 29 Settings 15. 16. 17. 18. 19. Click Next to confirm the settings. The computer will then initialize the settings. Click Finish.
Windows XP Information Help Right-click the taskbar icon to bring up the menu to select Help or How to use the Security Platform Features. Infineon Security Platform Settings Tool The Infineon Security Platform Settings Tool allows you to manage and check the TPM state, manage your password information, and to backup and restore the TPM data. As TPM is usually administered within large enterprises and organizations, your system administrator will need to assist you in managing the information here.
Windows XP Information Fingerprint Reader Module If you have included the fingerprint reader in your purchase option you will need to install the driver as per the instructions below. Help & Manual Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. Right-click the taskbar icon to bring up the menu to select Help. Before beginning the enrollment process it is recommended that you go through the fingerprint tutorial.
Windows XP Information User Enrollment 1. 2. 3. 4. 5. 6. 7. 8. Click Start > Programs/All Programs > Protector Suite QL > User Enrollment, or double click the taskbar icon (click Start fingerprint enrollment). On the first run of the program you will be asked to click the button to accept the license, and then click OK. Click Next (the enrollment method will automatically be configured), and then click Finish.
Windows XP Information 10. 11. 12. 13. Repeat the process for all the fingers you wish to enroll (see sidebar), and then click Next > Finish. Click “Help” in the Fingerprint Control Center to get more information on any topic. You can also run the Tutorial, or Introduction (to run the product tour video) to get more information.
Windows XP Information Protector Suite TPM Initialization 1. Click Start > Programs/All Programs > Protector Suite > Control Center, or double click the taskbar icon . 2. Click System Settings and click TPM (Tab). Figure D - 33 Protector Suite TPM Initialization & Multifactor 3. Click Initialize TPM. 4. Click Next > Finish. 5. Click OK to close the System Settings control panel.
Windows XP Information 6. 7. 8. Click Enroll or Edit Fingerprints and then click Next. Enter the password or swipe a finger and click Next. Select the Authentication Factors in Mulifactor to configure fingerprint authentication along with TPM. 9. Enter a password and retype it to confirm it and then click Next. 10. Click Next > Next > Finish.
Windows XP Information Fingerprint Control Center Features Application Launcher The Application Launcher allows you to register applications to be launched when assigned to a particular finger. Simply copy the application icon on to one of the registered fingers and ten click OK to close the application window. Once registered the application will launch when you swipe the appropriate finger across the sensor.
Windows XP Information PC Camera Module Before installing the optional PC Camera module driver use the Fn + F10 key combination (see “Function Keys & Visual Indicators” on page D - 5) to toggle power to the PC Camera module. The PC Camera module uses the BisonCap application to capture video files. Make sure you install the PC Camera driver (see “PC Camera (Optional)” on page D - 31).
Windows XP Information PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then doubleclick the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View). 2. Click Advanced in the Volume > Device volume tab. 3. Click Options and scroll down and click Properties. 4.
Windows XP Information BisonCap BisonCap is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format. 1. 2. 3. Run the BisonCap application from the Start > Programs/All Programs > BisonCam menu (it is recommended that you set the capture file before the capture process - see Set Capture File below). Go to the Capture menu heading (if you wish to capture audio check “PC Camera Audio Setup” on page D - 53) and select Start Capture.
Windows XP Information Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties) If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Windows XP Information Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the BisonCap program. Go to Options and scroll down to select Video Capture Filter.... Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Windows XP Information Zoom The BisonCap program allows you to zoom the camera in and out. 1. Run the BisonCap program. 2. Go to Zoom and select Zoom Out/Zoom In. Figure D - 36 Zoom/Setting Snapshot Folder The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture. D Taking Still Pictures The BisonCap program allows you to take still pictures. 1. Run the BisonCap program. 2.
Windows XP Information WLAN Module If you have included an Intel® Wi-Fi Link 5100/5300 Series (802.11 a/g/n) or 802.11b/g WLAN module in your purchase option, use the Fn + F11 key combination to toggle power to the module. Your installation procedure will be dependent upon which WLAN module is included in your purchase option.
Windows XP Information Intel WLAN Configuration 1. 2. 3. 4. 5. Configure the settings by going to the Intel PROSet Wireless WiFi Connection Utility (Start > Programs/All Programs > Intel PROSet Wireless WiFi Connection Utility), or by double-clicking the taskbar icon . Click to select any available network, and click Connect to establish a connection. If you do not see your Wireless Access Point click Refresh (button). Click Help (link) to bring up the Help Menu.
Windows XP Information 802.11b/g WLAN Configuration 1. 2. The operating system is the default setting for Wireless LAN control in Windows XP. Access any available wireless networks from Network Connections > Wireless Network Connection menu in Windows, or click the icon in the taskbar, and click View Wireless Connections.
Windows XP Information 3.75G/HSPA Module Options If you have included an optional 3.75G/HSPA module in your purchase option follow the instructions on page 7 - 46 to install the USIM card (which will be provided by your service provider), and then install the application. There are three optional 3.75G/HSPA modules available for this series of computer models. Each module is supplied with the appropriate application software. Before installing the application, make sure that the 3.
Windows XP Information Before installing the application, make sure that the 3.75G/HSPA module is ON (installing the driver with the module off will not allow the software to detect the module hardware correctly). Use the Fn + key combination (see “Function Keys & Visual Indicators” on page D - 5) to toggle power to the 3.75G/HSPA module. When the 3.75G/HSPA module is powered on, the indicator will briefly be displayed. Make sure you install the drivers in the order indicated in Table D - 3, on page D - 29.
Windows XP Information 3G Watcher Application Installation 1. Enable power to the module by pressing the Fn + key combination (the on screen icon will indicate the module’s power status). 2. If a Found New Hardware window appears, click Cancel. 3. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 4. Click Option Drivers (button). 5. Click 2.3.5G Generation Module > Yes, and then click Next. 6. Click the button to accept the license agreement, and then click Install. 7.
Windows XP Information HSPA Modem Interface Installation 1. Enable power to the module by pressing the Fn + key combination (the on screen icon will indicate the module’s power status). 2. If a Found New Hardware window appears, click Cancel. 3. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 4. Click Option Drivers (button). 5. Click 2.3.5G Generation Module > Yes, and then click Next. 6. Click Next > Install > Finish. 7.
Windows XP Information Mobile Partner Application Installation 1. Enable power to the module by pressing the Fn + key combination (the on screen icon will indicate the module’s power status). 2. If a Found New Hardware window appears, click Cancel. 3. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 4. Click Option Drivers (button). 5. Click 2.3.5G Generation Module > Yes. 6. Choose the language you prefer and click OK. 7.
