Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Preface IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. VI • Only use a power adapter approved for use with this computer.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Recharge the batteries using the computer’s system. Incorrect recharging may make the battery explode. • Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qualified service personnel. • Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully.
Preface Touch Panel Care • Touch Panels are made of glass, so do not subject them to heavy shock or stress. • Do not place heavy objects on the Touch Panel. • Please use a dry soft cloth when cleaning (do not use any organic solvent acid or alkali solution). Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC adapter and cables. Stow them in the carrying bag. The AC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the computer - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eyestrain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. • Position the display directly in front of you at a comfortable viewing distance. • Adjust the display-viewing angle to find the best position.
Preface Contents Notice ...........................................................................I Trademarks .......................................................... I FCC Statement ...................................................II Instructions for Care and Operation ................. IV Power Safety ..................................................... VI Battery Precautions ..........................................VII Touch Panel Care .......................................... VIII Cleaning ...
Preface Stylus Pen Holder ................................................1-16 Right Side View .....................................................1-17 4-in-1 Flash Card Reader ....................................1-17 Two USB 2.0 Ports .............................................1-18 PC Card Slot ........................................................1-18 Rear View ...............................................................1-19 External Monitor (VGA) Port .............................
Preface TouchPad and Buttons/Mouse ...............................2-25 Configuring the Infrared Transceiver .....................2-26 Adding a Printer .....................................................2-27 USB Printer ..........................................................2-27 Install Instructions: ..............................................2-27 Parallel Printer ......................................................2-28 Install Instructions: ..............................................
Preface Set Capture File ......................................................3-29 Eliminating Screen Flicker .....................................3-30 Wireless LAN Module ...........................................3-31 Drivers & Utilities Overview ..................................................................4-1 What to Install ..........................................................4-2 Windows XP & 2000 Service Packs ......................4-2 New Hardware Found ....................................
Preface Working with Sub-Menus ........................................5-7 Startup Menu ............................................................5-8 Fast Boot (Startup Menu) .........................................5-8 Boot Device (Startup Menu) ....................................5-9 Display (Startup Menu) ............................................5-9 Enable Battery Low Beep (Startup Menu) ...............5-9 Enable Power On Beep (Startup Menu) .................5-10 Display OEM logo (Startup Menu) ....
Preface CD Device (Optional) ............................................7-12 Keyboard and Mouse .............................................7-13 Operation ................................................................7-14 Advanced Power Saving Power Schemes & Processor Performance .............A-2 Intel CPU SpeedStep Controls ................................A-3 Model A Specifications Processor Types ....................................................... B-1 Core Logic ................................
Introduction Chapter 1: Introduction Overview Notes This manual refers to the hardware and essential software required to run your computer. Depending on how your system is configured, some or all of the features described may already be set up. This chapter covers: • • The Manual System Map — — how to use it navigating around your computer Check the light colored boxes with the mark above to find detailed information about the computer’s features.
1 Introduction Warning Boxes No matter what your level please pay careful attention to the warning and safety information indicated by the symbol. Also please note the safety and handling instructions as indicated in the Preface. Not Included Operating Systems (e.g. Windows XP etc.) have their own manuals, as do applications (e.g. word processing, spreadsheet and database programs). If you have questions about the operating systems or programs then please consult the appropriate manuals.
Introduction Quick Start Guide This guide assumes that you are already familiar with computers and can tell at a glance what and where all the key components are. If you are not that comfortable with this type of device, then please refer to the following pages, which give an overview of the system. It is still best to review these steps, before taking any action. If there is anything you are not sure about, then please refer to the appropriate chapter before continuing.
1 Introduction System Map Your computer has a lot of built-in features. Most of these are enabled by your operating system. Further explanations of the various subsystems are covered in the chapter or pages indicated. Model Differences This notebook series includes two different model types. Model A includes a Touch Panel screen, Model B does not. The specifications for each model are listed in “Model A Specifications” on page B - 1 and “Model B Specifications” on page C - 1.
Introduction Getting to Know Your Computer The following graphics will help you to become familiar with the basic functions, and to learn the location of the various ports and components of your computer. Design Differences This manual refers to the two notebook designs pictured on this page. Design I Design II The designs vary slightly in external design. Photographs used throughout this manual are of Design I.
1 Introduction Top View Figure 1 - 2 Top View with LCD Panel Closed 1. 2. 2 LCD Latches LED Indicators 1 1 To open the LCD display: 1. 2. 3. 4. 5. 6. 1 - 6 Top View Place the computer on a stable surface. Press the latches in the direction of the arrows 1 (press in) to release the top cover. Lift the top cover to reveal the LCD Swivel Screen and keyboard. Adjust the LCD Swivel Screen to a comfortable viewing angle. The LED indicators 2 show the power and battery status of the computer.
Introduction The LCD Swivel Screen You can use the computer either in Notebook Mode, or in Tablet Mode. To put the computer into Tablet Mode: 1. 2. 3. Unlock the LCD side hinges 1 & 2 by moving them in the direction of the arrows. Carefully rotate the LCD fully in the direction indicated by the arrow 3 , then lock the side hinges 1 & 2 . Move latches 4 & 5 in and to the left (if they are not already in this position), then push the LCD down to lock it in position.
1 Introduction Top View with LCD Open Figure 1 - 4 1 Top View with LCD Panel Open 1. Built-In PC Camera (Optional) 2. LCD Swivel Screen 3. LED Power Indicators 4. Cover Sensors 5. LCD Swivel Hinge 6. LCD Side Hinges 7. Power Button 8. Speakers 9. Keyboard 10. TouchPad and Buttons 11.
Introduction PC Camera If you have purchased the optional PC Camera, make sure you install the software application (see pages 4 - 12, 4 - 19 & 3 - 26). LCD Swivel Screen The computer comes with a TFT (Thin Film Transistor), Liquid Crystal Display screen (see “LCD” on page B - 1/“LCD” on page C - 1 for details). The screen can rotate and tilt for best visibility in Notebook Mode, and flip for use in Tablet Mode.
1 Introduction Lid Button It is recommended that you set the lid (left LCD cover sensor) power button to “Do nothing”. This will prevent accidentally triggering a power saving mode when you rotate the LCD swivel screen. Cover Sensors These switches act as sensors to tell when the LCD Swivel Panel is closed, in Notebook Mode, or in Tablet Mode.
Introduction LCD Swivel & Side Hinges Release the side hinges in the direction indicated by the arrows on the top panel, and swivel the LCD panel in the direction indicated on the top panel. Power Button Press this button to turn your computer On or Off (see “Turning on the Computer” on page 2 - 4). This button may also be used as a suspend/resume key, once configured as such in the power management control panel of your operating system (see “Configuring the Power Button” on page 3 - 23).
1 Introduction Keyboard The computer has a “Win Key” keyboard including an embedded numeric keypad. It has the same features as a full-sized desktop keyboard and can easily be replaced with a different language keyboard should you desire. TouchPad & Buttons The pointing device features a sensitive glide pad for precise movements. It functions the same way as a two-button mouse.
Introduction Front View Figure 1 - 5 1 1 2 3 4 5 6 7 Infrared Communication The Infrared transceiver operates on a “Line of Sight”. Make sure nothing is blocking the “Line of Sight” between your system’s transceiver and the destination’s transceiver. Front View 1. 2. 3. 4. 5. 6. 7.
1 Introduction Headphone-Out Jack Headphones may be connected through this jack (the headphone-out jack is colored green). Note: Set your system’s volume to a reduced level before connecting to this jack. Infrared Transceiver The infrared transceiver enables communication between the computer and another similarly equipped device, and is 4M bps FIR, IrDA 1.1 compliant.
Introduction Hot-Key Buttons The three Hot-Key buttons include Tab & Esc keys (these keys are particularly useful in Tablet Mode), and a “Q” key (which also acts as a power button) to rotate the screen between Portrait and Landscape modes (see “Q Key Functions” on page 2 - 16 for full details). Playing DVD’s/VCD’s and Screen Rotation If you are playing a DVD/VCD video, do not rotate the screen while playing the video.
1 Introduction Figure 1 - 6 Left Side View Left Side View 1. 2. 3. Security Lock Slot Vent Stylus Pen Holder 1 2 3 Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. Vent This enables airflow to prevent the computer from overheating. Overheating To prevent your computer from overheating make sure nothing blocks the vent/fan intake while the computer is in use.
Introduction Right Side View Figure 1 - 7 Right Side View 1. 1 2 3 4-in-1 Flash Card Reader The card reader allows you to use four of the most popular digital storage cards. See “4-in-1 Card Reader” on page 2 - 14 and note the driver installation information in the sidebar. The formats that can be read include: • • • • MMC (MultiMedia Card) SD (Secure Digital) MS (Memory Stick) SM (SmartMedia Card) 2. 3. 4-in-1 Flash Card Reader Two USB 2.
1 Introduction Two USB 2.0 Ports Optional USB 2.0 CD Device If your purchase includes the external USB 2.0 CD Device, you can connect it to any USB port. USB Cables Make sure that your USB cable connector is orientated the correct way before inserting it into the USB Port. It will only fit one way (don’t force it). 1 - 18 Right Side View These USB 2.0 compatible ports (USB 2.0 is fully USB 1.
Introduction Rear View Figure 1 - 8 Rear View 1 2 3 4 5 Overheating 1. 2. 3. 4. 5. External Monitor (VGA) Port RJ-45 LAN Jack RJ-11 Phone Jack DC-In Jack Vent To prevent your computer from overheating make sure nothing blocks the vent/fan intake while the computer is in use. External Monitor (VGA) Port Connect an external monitor to this port to allow dual video or simultaneous display on the LCD and external monitor (see “Display Devices” on page 3 11).
1 Introduction RJ-11 Phone Jack This port connects to the built-in modem. You may plug the telephone line directly into this RJ-11 telephone connection. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. DC-In Jack Plug the supplied AC adapter into this jack to power your computer. Vent This enables airflow to prevent the computer from overheating.
Introduction Bottom View Figure 1 - 9 6 7 CPU The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 5 Bottom View 1. 2. 3. 4. 5. 6. 7. Stylus Pen Holder Battery Wireless LAN Module Cover Hard Disk Cover RAM Cover CPU Cover Vent 2 4 3 1 1 Overheating Stylus Pen Holder The stylus pen fits in this holder. Battery See “Battery Information” on page 3 - 24 for information on battery use and care.
1 Introduction Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module is OFF if you are using the computer aboard aircraft. When your computer ‘Boots Up’ the module will be ON. To toggle power to the WLAN module use the key combination Fn + F11, or the “VGA Rotate Application” on page 3 - 4. 1 - 22 Bottom View Wireless LAN (Network) Module The computer’s 802.
Using The Computer Chapter 2: Using The Computer 2 Overview To learn more about using your computer, please read this chapter.
Using The Computer 2 Power Button as Standby or Hibernate Button Fully ACPI-compliant OS’s such as Windows XP/2000 can use the “Power Options” control panel to set the power button to send the system into Standby or Hibernate mode (see your OS’s documentation, or “Configuring the Power Button” on page 3 23 for details). The Power Sources The computer can be powered by either an AC adapter or a battery pack. AC Adapter Use only the AC adapter that comes with your computer.
Using The Computer Battery The battery allows you to use your computer while you are on the road or an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging. We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 24.
Using The Computer 2 Shutdown Note that you should always shut your computer down by choosing the Shut Down/ Turn Off Computer command from the Start menu in Windows. This will help prevent hard disk or system problems. Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.
Using The Computer LED Indicators 2 There are two sets of LED indicators (LED Power Indicators and LED Status Indicators) on your computer that will display helpful information about the current status of the computer. The LED Power Indicators are also visible when the top of your computer is closed (in Notebook Mode).
Using The Computer LED Status Indicators 2 Icon Color Description Green The WLAN Module is On Green Hard Disk/System activity Green Number Lock is activated Green Caps Lock is activated Green Scroll Lock is activated (to activate press Fn & ScrLk) Table 2 - 2 LED Status Indicators 2 - 6 LED Indicators
Using The Computer Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" IDE hard disk drives with a height of 9.5 mm. The hard disk 1 is accessible from the bottom of your computer as seen below. Further details on removing and inserting the hard disk are available in “Upgrading the Hard Disk Drive” on page 6 - 4.
Using The Computer 2 Media Warning Don’t try to remove a floppy disk while the system is accessing it. This may cause the computer to “crash” and damage your data. The Floppy Disk Drive (Optional) The optional external 1.44 MB, 3.5" USB floppy disk drive can connect to any of the USB ports on the computer. By default it is drive “A:” and can be used as a boot device if properly set in the BIOS (refer to “Boot Device (Startup Menu)” on page 5 - 9).
Using The Computer CD Device/DVD Device (Optional) The optional external CD/DVD Device is USB 2.0 compliant and can connect to any of the USB ports on the computer. If your purchase configuration does not include this option you can purchase a USB CD/DVD Device from a computer store. AC Adapter Power Switch Optional CD Device with Desktop Computers You can use the CD device with desktop computers without the AC power adapter (the power switch should be set to USB). USB 2.
Using The Computer 2 Playing Audio CD’s in Windows 2000 To play audio CD’s in an external USB CD Device, follow this procedure: Optional CD/DVD Device Options The optional external CD device is available in CD-ROM, or DVD-ROM, or CD-RW, or Combination CD-RW and DVD-ROM drive configurations. The CD Device is usually labeled “Drive D:”, and may be used as a boot device if properly set in the BIOS (“Boot Device (Startup Menu)” on page 5 - 9).
Using The Computer Loading CDs or DVDs To insert a CD/DVD, press the eject button and carefully place a CD/DVD onto the disc tray with label-side facing up (use just enough force for the disc to click onto the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you are ready to start. The LED indicator will light up while data is being accessed, or while an audio/video CD, or DVD, is playing.
Using The Computer DVD Regional Codes 2 DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module with another computer.
Using The Computer Changing DVD Regional Codes 2 Go to the Control Panel in WindowsXP/Windows 2000 and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/ CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties menu, and select the DVD Region (tab) to bring up the control panel as seen in “DVD Regional Codes (Windows XP)” on page 2 - 12.
Using The Computer 2 SmartMedia Cards Note that SmartMedia Cards should be inserted as illustrated in Figure 2 - 5. 4-in-1 Card Reader The 4-in-1 Card Reader allows you to use four of the most popular digital storage cards. Make sure you install the ENE-PCMCIA driver as this includes support for the Card Reader (see “What to Install” on page 4 - 2).
Using The Computer PC Card Slot The computer is equipped with a PCMCIA 3.3V/5V slot for one type II PC Card. Make sure you install the driver for the PC Card (see “What to Install” on page 4 - 2). Inserting and Removing PC Cards • Align the PC Card with the slot and push it in until it locks into place. • To remove a PC Card, simply press the eject button 1 next to the slot.
Using The Computer 2 Right Cover Sensor The right LCD cover sensor (see “Cover Sensors” on page 1 10) is used in conjunction with the “Q” HotKey to tell the computer when it is in Tablet mode (when the computer is in Tablet mode the right cover sensor is depressed). If you are in Notebook mode you can perform the same set of functions listed in the table by tapping/pressing the “Q” key and pressing the right cover sensor simultaneously.
Using The Computer The Keyboard The Function Keys On the bottom-left of the keyboard is the Fn key, or Function key, which allows you to change operational features instantly. To use the functions press and hold the Fn key, and then press the appropriate function key (F3 - F11 etc.) located on your keyboard.
Using The Computer 2 Numeric Keypad Special Characters Some software applications allow the number-keys to be used with Alt to produce special characters. These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that Num Lock is on. The keyboard has an embedded numerical keypad for easy numeric data input. Activate the Number Lock feature by pressing the Fn and Num Lk key combination.
Using The Computer Touch Panel (Model A Only) If your computer is Model A the LCD screen also acts as a Touch Panel when the driver is installed (see pages 4 - 13 & 4 - 20). Use the stylus pen provided to point directly to objects on the screen in much the same way as you would use your mouse as the pointing device.
Using The Computer 2 Touch Panel Calibration Make sure you calibrate the Touch Panel from the Touch Panel Set-Up and Configuration Utility. 1.Click the Calibration tab. 2.Click the Calibrate Now button. 3.Use the input device to touch the cross at the different positions on screen. 4.Click the Update button.
Using The Computer Touch Panel Warning Touch Panel Input Device (Model A Only) Be very careful not to press too hard with the stylus pen when using it as the input device. Use only the approved stylus pen provided. When writing on the screen, avoid sliding the stylus pen (or any object) in the area around the edge of the screen (between the LCD and the frame). Do not use any sharp or pointed objects as your input device e.g. the end of a pen or pencil.
Using The Computer 2 ritePen The ritePen program is a handwriting recognition application which allows you to use the provided PDA stylus pen to write text on the screen. The handwriting will then be converted into text for use in any application. riteMail The riteMail program is a note-taking and editing application which allows you to export the notes to applications e.g as a handwritten email.
Using The Computer ritePen If you do not see the ritePen notification icon in the taskbar you can open the utility by going to the Start menu and pointing to Programs/All Programs > Parascript > ritePen, and clicking ritePen. The icon will appear in the taskbar to indicate it is active. Use the input device to click the icon to make the utility inactive (the icon will change to ).
Using The Computer 2 Emailing Notes Go to the Tools menu and select Options, then fill in the User and Mail setup information before sending any notes as emails. Click the Send button to send the mail. riteMail Run the riteMail program from the Start menu and pointing to Programs/All Programs > Parascript > ritePen, and clicking riteMail.
Using The Computer TouchPad and Buttons/Mouse The TouchPad is a device for pointing (controlling input positioning) on the computer’s display screen by sensing finger movement, and downward pressure. It is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Using The Computer 2 Infrared Communication The infrared transceiver operates on a “Line of Sight”. Make sure nothing is blocking the “Line of Sight” between your system’s transceiver and the destination’s transceiver. Configuring the Infrared Transceiver To configure the computer’s settings for Fast Infrared (FIR) communication follow these steps: 1. 2. 3. 4. 5. 6. Click Start, point to Settings (or just click Start and click Control Panel) and click Control Panel.
Using The Computer Adding a Printer 2 The most commonly used peripheral is a printer. The following conventions will help you to add a printer, however it is always best to refer to the printer manual for specific instructions and configuration options. USB Printer Most new printers have a USB interface connection. You may use any of the USB ports on your computer to connect the printer. Install Instructions: 1. 2. 3. 4. 5.
Using The Computer Parallel Printer 2 This is still a very common type of printer. A Parallel to USB converter may be purchased at most computer stores. Install Instructions: 1. 2. 3. 4. 5. 6. 2 - 28 Adding a Printer Set up the printer according to its instructions (unpacking, paper tray, toner/ ink cartridge etc.). Attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer.
Advanced Controls Chapter 3: Advanced Controls Overview This chapter covers: • • • • Advanced Video Controls Power and Battery Management Features PC Camera Module (optional) Wireless LAN Module (optional) Drivers You are unable to use most advanced controls until the necessary drivers and utilities are properly installed.
Advanced Controls 3 Protecting the LCD Do not allow any foreign objects (i.e. paper or plastic) to get between the lid/LCD and the work panel. They could damage or scratch the LCD and/or accidentally activate the close cover switch. Advanced Video Controls This section is about making adjustments for the LCD, and switching display devices. Opening the LCD As you open the lid, adjust it so you can look at the screen straight on, without any glare.
Advanced Controls Video Memory The computer does not have dedicated video memory. The video memory available on your computer is configured in two modes of operation. VGA Shared Memory This is the pre-allocated memory size for VGA compatibility. This is fixed in the BIOS at 32MB (see page 5 - 11). This memory is allocated from your system memory e.g. if you computer has 256MB of memory (RAM), then 32MB will be allocated to video leaving the system with 224MB of RAM.
Advanced Controls 3 Playing DVD’s/VCD’s and Screen Rotation If you are playing a DVD/VCD video, do not rotate the screen while playing the video. If you wish to rotate the screen quit the player program first, rotate the screen, then open the player to play the video. Screen Rotation The screen may be rotated to appear in Landscape Mode or Portrait Mode by means of the screen rotation driver or “Q” Hot-Key (see “Hot-Keys” on page 2 - 16).
Advanced Controls “Q” Hot-Key In Tablet Mode the “Q” key is used to toggle the screen rotation between Landscape and Portrait configurations; it also acts as a power button. Make sure you gently tap the “Q” key to get the screen to rotate (do not press the key for too long or it will initiate a power saving mode). See “Q Key Functions” on page 2 - 16 for full details on the “Q” key functions.
Advanced Controls 3 Screen Resolution/ Screen Area Note You may set the resolution to a higher setting than the panel supports, however this will require you to pan (scroll) around the screen as the display area will be larger than what you can see on the LCD. Video Driver Controls The video interface lets you change the screen resolution and color output to whatever is most comfortable/efficient for you. This is a matter of hardware, video memory and the driver for your operating system.
Advanced Controls Display Properties Figure 3 - 3 Display Properties 1 Intel(R) Extreme Graphics Controller Properties 2 3 When the Display Properties control panel is open, click the Advanced 3 (button) to bring up the options tabs. Clicking through these tabs allows you to make any video adjustments you require. You can click Graphics Properties (button) in the Intel(R) Extreme Graphics 2 for Mobile tab (in the Advanced options) to access the screens in Figure 3 - 5 on page 3-9.
Advanced Controls 3 Taskbar You may also access the control panel from the taskbar at the bottom right of the screen. Click on the icon to bring up the menu and scroll to Graphics Options > Graphics Properties. Intel Video Driver Controls After installing the video driver there will be an additional control panel entitled Intel(R) Extreme Graphics 2 M. To get to the control panel to make changes to the Graphics Properties, do the following: 1. 2.
Advanced Controls You may make changes to the Devices, Color, and Schemes by clicking the appropriate tab and adjusting the setting, then clicking OK. The Information and Open GL tabs display useful information about the graphics properties of your computer, and the Support item in the Information tab has weblinks to the latest information (drivers, troubleshooting issues etc.) on the Intel Website. Screen examples are shown on the following page.
Advanced Controls 3 Application.exe You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application right-click its shortcut on the desktop click Properties. Click the Shortcut (tab) and see where the executable file is located by clicking the Find Target (button). Note the location and you will then be able to browse to this file.
Advanced Controls Display Devices Besides the built-in LCD, you can also use an external monitor as your display device. A monitor connects to the external monitor (VGA) port 1 . Figure 3 - 6 Rear View 1 Switching/Enabling Displays (Keyboard) You can switch display devices with the Fn + Display (F7) toggle. With the video driver installed, you also can use its built-in controls to switch the display options.
Advanced Controls 3 Vertical Refresh Rate The vertical refresh rate of your monitor is important. If it is too low and/or you’re using fluorescent lighting, the screen will appear to flicker. To reduce flickering on a monitor, use faster refresh rates (we recommend a refresh rate of 72Hz or more). But first check your monitor’s documentation to make sure it can support the rates listed by the video driver. The default refresh rate for monitors (without drivers) is 60Hz.
Advanced Controls Multi-Monitor Modes In addition to the single LCD display mode you have the following MultiMonitor modes available when the external monitor is attached. Intel(R) Dual Display Clone This mode will drive multiple displays with the same content. Use this feature to display the screen through a projector for a presentation. Extended Desktop This mode allows a desktop to span multiple displays and acts as a large workspace. This creates a lot more screen area for display.
Advanced Controls To Enable Dual Display Clone Mode: 1. 2. 3 3. 4. 5. 6. Figure 3 - 8 Device Settings (Clone Mode) 3 - 14 Display Devices Plug the monitor into the appropriate port. Go to the Intel(R) 82852/82855 GM/GME Graphics Controller Properties control panel (see “Intel Video Driver Controls” on page 3 - 8) and select Devices (tab). Click the Intel(R) Dual Display Clone icon in the devices tab (Note: this option is only available when you have attached the monitor).
Advanced Controls To Enable Extended Desktop Mode: 1. 2. 3. 4. 5. 6. Plug the monitor into the appropriate port. Go to the Intel(R) 82852/82855 GM/GME Graphics Controller Properties control panel (see “Intel Video Driver Controls” on page 3 - 8) and select Devices (tab). Click the Extended Desktop icon in the devices tab (Note: this option is only available when you have attached the monitor). Choose which device is to be the Primary display, and which is to be Secondary.
Advanced Controls To Enable Extended Desktop (Display Properties) 3 Extended Desktop Mode If Intel Dual Display Clone mode is currently enabled, you must use the Intel(R) 82852/82855 GM/ GME Graphics Controller Properties to switch the display. 1. 2. 3. 4. 5. Plug the monitor into the appropriate port. Click Start, point to Settings (or just click Control Panel) and click Control Panel (if you are in Category View choose Appearance and Themes). Double-click Display (icon).
Advanced Controls Power Management Features To conserve power, especially when using the battery, your computer uses the ACPI power management system. Power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Advanced Controls Enabling Power Options Power Options are enabled through the control panel in your Windows system (Power Options). With other operating systems you may have power management available, so check your documentation. 3 Figure 3 - 11 Power Options Control Panel You may conserve power through Power Schemes (individual components) or throughout the whole system.
Advanced Controls Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes. You can also adjust the settings for each scheme to set the monitor to turn off after a specified time, and the computer's hard disk motor to turn off if the hard disk drive has not been accessed for a specified period of time (if the system reads or writes data, the hard disk motor will be turned back on).
Advanced Controls Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose the Home/Office scheme for maximum performance when the computer is powered from an AC power source.
Advanced Controls Conserving Power (System) With this function you can stop the computer’s operation and restart where you left off. This system features Standby and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - Figure 3 - 13 on page 3-22). Hibernate Mode vs. Shutdown Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to turn it on.
Advanced Controls 3 System Resume The system can resume from Standby mode by: • Pressing the power button • Pressing the key combination Fn + F4 • An alarm resume that is enabled and expires Standby Standby saves the least amount of power, but takes the shortest time to return to full operation. During Standby the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory.
Advanced Controls Configuring the Power Button The power button may be set to send the computer in to either Standby or Hibernate mode. In Standby mode, the LED will flash green. In Hibernate mode the LED will be Off (battery powered)/Orange (AC Adapter powered). In a power saving mode set to save power through individual components (e.g. hard disk, monitor), the LED will remain green. Lid Button It is recommended that you set the lid (left LCD cover sensor) power button to “Do nothing”.
Advanced Controls 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. Battery Information Follow these simple guidelines to get the best use out of your battery. New Battery Always completely discharge, then fully charge, a new battery before using it (see “Battery FAQ” on page 3 - 25 for instructions on how to do this).
Advanced Controls Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 6 - 3. Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery.
Advanced Controls 3 Taking Still Pictures You may take still pictures in the Windows XP operating system only. Double-click the My Computer icon on the desktop, or go the Start menu and point to My Computer, then click it. Double-click the CMM PC Camera icon. PC Camera If you have purchased the optional PC Camera you will need to install the device driver for it as indicated in “PC Camera (Win2000)” on page 4 - 12 and “PC Camera (WinXP)” on page 4 - 19.
Advanced Controls PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 3 (WinXP) 1. 2. 3. 4. 5. 6. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double-click the Sounds & Audio Devices icon (Category View > Speech, and Audio Devices). Click Advanced in the Volume tab. Click Options (Volume Control) and scroll down and click Properties.
Advanced Controls Figure 3 - 16 Audio Setup 3 3 - 28 PC Camera
Advanced Controls AMCAP AMCAP is a video viewer useful for general purpose video viewing and testing, and capturing video files to .avi format. 1. 2. 3. 4. 5. Run the AMCAP program from the Start > Programs/All Programs > CMM PC Camera menu (it is recommended that you set the capture file before the capture process - see Set Capture File below). Go to the Capture menu heading (if you wish to capture audio make sure that the Capture Audio option is ticked) and select Start Capture.
Advanced Controls Eliminating Screen Flicker If you find that the video screen in the AMCAP program is flickering, you can try to adjust the option from the Video Capture Filter options. 3 1. 2. 3. Figure 3 - 17 Camera Controls 3 - 30 PC Camera Run the AMCAP program from the Start > Programs/All Programs > CMM PC Camera menu. Go to Options and scroll down to select “Video Capture Filter...”. You can choose either 50Hz or 60Hz from the No Flicker box.
Advanced Controls Wireless LAN Module The computer’s 802.11b Wireless LAN module, and its antenna and other components, are not externally visible (please check with your service representative). Make sure you install the driver (see pages 4 - 11 & 4 - 17). The 802.11b Wireless LAN module driver is provided on its own CD, and is not on the Device Drivers & Utilities + User’s Manual CD-ROM. You will also find instructions on pages 4 - 12 & 4 - 18 for accessing the User Guides.
Advanced Controls Figure 3 - 18 3 Windows XP Network Control Panels Windows 2000 3 - 32 Wireless LAN Module
Drivers & Utilities Chapter 4: Drivers & Utilities Overview This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities What to Install 4 The Device Drivers & Utilities + User’s Manual CD-ROM contains the drivers and utilities necessary for the proper operation of the computer. (The drivers for the Wireless LAN and optional PC Camera modules and are on the separate CDs provided.) Table 4 - 1 on page 4-7 lists what you need to install manually according to your choice of the operating system. It is very important that the drivers are installed in the order indicated in the table.
Drivers & Utilities Windows 2000 with Service Pack 4 Service Pack Installed Make sure that your Windows 2000 version includes Service Pack 4 on the installation CD. To see which Service Pack is currently installed on your computer go to the General tab of the System control panel. Right-click the My Computer icon on the desktop or in the Start menu (in WinXP only) and select Properties. The Service Pack currently installed on your system will be listed under the “System:” heading.
Drivers & Utilities New Hardware Found 4 If you see the message “New Hardware Found” (Found New Hardware Wizard) during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure as directed. Navigate (Browse..) to D: You will notice that many of the instructions for driver installation require you to “Navigate (Browse) to D:”. In this case “D:” is the drive specified for your CD device.
Drivers & Utilities Authorized Driver Message If you receive a message telling you that the driver you are installing is not authorized (Digital Signature Not Found), just click Yes or Continue Anyway to ignore the message and continue the installation procedure. Updating/Reinstalling Individual Drivers You will receive this message in cases where the driver has been released after the version of Windows you are currently using.
Drivers & Utilities Driver Installation 4 1. You have a choice of installation methods to install your drivers. 2. Automatic Driver Installation 3. Insert the Device Drivers & Utilities + User’s Manual CD-ROM and the Drivers Installer application will run automatically. 4. Figure 4 - 1 - Drivers Installer 4 - 6 Driver Installation Check the driver installation order from the table Table on page 4-7 (the drivers must be installed in this order).
Drivers & Utilities Manual Driver Installation Insert the Device Drivers & Utilities + User’s Manual CD-ROM and close the Drivers Installer application. Follow the procedures listed in this chapter (the drivers for the Wireless LAN and optional PC Camera modules and are on the separate CDs provided). *Service Pack Installed To see which Service Pack is currently installed on your computer go to the General tab of the System control panel.
Drivers & Utilities Windows 2000 This section covers driver and utility installation instructions for the Windows 2000 (SP4 installed). 4 Windows 2000 with Service Pack 4 Make sure that your Windows 2000 version includes Service Pack 4 on the installation CD. Chipset (Win2000) 1. Click Start (menu) > Run... 2. Navigate (Browse..) to D:\Drivers\inf_update\infinst_autol.exe and click OK. 3. Click Next > Yes > Next. 4. Click Finish to restart the computer. Windows 2000 (SP4) Internet Explorer 5.
Drivers & Utilities Audio (Win2000) LAN (Win2000) 1. Click Start (menu) > Run... 2. Navigate (Browse..) to D:\Drivers\Audio\Setup.exe and click OK. 3. Click Next. 4. Click Finish to restart the computer. 5. You can click the AC97 Audio Configuration icon in the taskbar for configuration options. 1. Click Start (menu) > Run... 2. Navigate (Browse..) to D:\Drivers\Lan\Setup.exe and click OK. 3. Click Next. 4. Click Finish. 5. The network settings can now be configured. Modem (Win2000) Video (Win2000) 1.
Drivers & Utilities 4 ENE-PCMCIA (Win2000) TouchPad (Win2000) This driver is also required by the 4-in-1 Card Reader. 1. Click Start (menu) > Run... 2. Navigate (Browse..) to D:\Drivers\ENEPCMCIA\Setup.exe and click OK. 3. Click Next > Next. 4. Click Finish to restart the computer. 1. Click Start (menu) > Run... 2. Navigate (Browse...) to D:\Drivers\Touch Pad\Setup.exe and click OK. 3. To continue click Next > Next > Next (click Yes if asked if you want to continue). 4.
Drivers & Utilities Wireless LAN (Win2000) Make sure the module is powered on before installing the driver. To toggle power to the WLAN module use the key combination Fn + F11, or “VGA Rotate Application” on page 3 - 4. 1. Insert the Intel PRO CD-ROM into the CD drive. 2. Click Wireless LAN Adapters (button). 3. Click Install Software (button). 4. Click Next. 5. Click the button to accept the license and click Next > Next > Install > Finish. 6. Click Start (menu), point to Settings and click Control Panel.
Drivers & Utilities You can view the User Guides by inserting the Intel PRO CD-ROM and clicking Wireless LAN Adapters (button) > View User Guides (button). 4 PC Camera (Win2000) 1. Insert the PC Camera CD-ROM into the drive. 2. The program will run automatically. 3. Click Next (click Yes if asked if you want to continue at any time). 4. Click Finish and restart the computer. 5. After restart the computer will find the new hardware for you (click Yes if asked if you want to continue at any time). 6.
Drivers & Utilities Screen Rotation (Win2000) 1. Click Start (menu) > Run... 2. Navigate (Browse...) to D:\Drivers\VGARotate-AP\SETUP.EXE and click OK. 3. Click Next. 4. Click Finish to restart the computer. Touch Panel (Win2000) Only Model A computers support touch panel features. If your computer is Model B it is not necessary to install the driver. 6. Select “Display a list of the known drivers for this device so that I can choose a specific driver” and click Next. 7.
Drivers & Utilities Windows XP This section covers driver and utility installation instructions for the Windows XP OS. 4 Chipset (WinXP) 1. Click Start (menu) > Run... 2. Navigate (Browse..) to D:\Drivers\inf_update\infinst_autol.exe and click OK. 3. Click Next > Yes > Next. 4. Click Finish to restart the computer. Windows XP Service Pack 1/1a Make sure you install Windows XP Service Pack 1/ 1a (or a Windows XP version which includes Service Pack 1/1a) before installing any drivers.
Drivers & Utilities Video (WinXP) Modem (WinXP) 1. Click Start (menu) > Run... 2. Navigate (Browse..) to D:\Drivers\VGA\Setup.exe and click OK. 3. Click Next > Yes. 4. Click Finish to restart the computer. 5. See “Video Driver Controls” on page 3 - 6 for details on adjusting the video settings. 1. Click Start (menu) > Run... 2. Navigate (Browse..) to D:\Drivers\Modem\WinXP\Setup.exe and click OK. 3. Click (button). 4. Click . 5. The modem is ready for dial-up configuration. LAN (WinXP) 1.
Drivers & Utilities 4 ENE-PCMCIA (WinXP) TouchPad (WinXP) This driver is also required by the 4-in-1 Card Reader. 1. Click Start (menu) > Run... 2. Navigate (Browse..) to D:\Drivers\ENEPCMCIA\Setup.exe and click OK. 3. Click Next > Next. 4. Click Finish to restart the computer. 1. Click Start (menu) > Run... 2. Navigate (Browse...) to D:\Drivers\Touch Pad\Setup.exe and click OK. 3. To continue click Next > Next > Next (click Continue Anyway if asked if you want to continue). 4.
Drivers & Utilities Wireless LAN (WinXP) Make sure the module is powered on before installing the driver. To toggle power to the WLAN module use the key combination Fn + F11, or “VGA Rotate Application” on page 3 - 4. 1. Insert the Intel PRO CD-ROM into the CD drive. 2. Click Wireless LAN Adapters (button). 3. Click Install Software (button). 4. Click Next. 5. Click the button to accept the license and click Next > Next > Install > Finish. 6.
Drivers & Utilities 4 1. Insert the Intel PRO CD-ROM into the CD drive. 2. Click Wireless LAN Adapters (button). 3. Click Install Administration Tools (button). 4. Click Next. 5. Click the button to accept the license and click Next > Next > Install > Finish. 6. You can configure the settings by going to the Start menu and pointing to Programs/All Programs and clicking Intel Network Adapters, then clicking either the Intel (R) PROset icon, or the options under the Access Point Administration Tools.
Drivers & Utilities PC Camera (WinXP) 1. Insert the PC Camera CD-ROM into the drive. 2. The program will run automatically. 3. Click Next (click Continue Anyway if asked if you want to continue at any time). 4. Click Finish to restart the computer. 5. When the Found New Hardware Wizard appears select “Install the software automatically (Recommended)” then click Next. 6. Click Finish and restart the computer (click Yes to do so automatically when the dialog box appears). 7.
Drivers & Utilities Touch Panel (WinXP) Only Model A computers support touch panel features. If your computer is Model B it is not necessary to install the driver. 4 1. If you can see the My Computer icon on your desktop (if you cannot see the My Computer icon go to step 2) click on it once to select it, then right-click it to make the sub-menu appear and scroll down to Properties and click on it (go to step 3). 2.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter is about the computer’s built-in software. Your computer comes with built-in BIOS (Basic Input Output System) which is an essential set of software routines stored on a chip in your computer. These routines serve to describe your computer’s hardware to your chosen operating system, and provides an interface between the two. The BIOS includes the POST (Power On Self Test) and the SCU (System Configuration Utility).
BIOS Utilities The POST Screen 5 1. 2. 3. 4. BIOS information CPU type Memory status Enter SCU prompt appears only during POST Note: The POST screen pictured is for guideline purposes only. The POST screen on your computer may appear slightly different. If you choose the Fast Boot option you will see an abbreviated version of this screen. If you choose the Display OEM logo thescreen will not appear (see page 5 - 4.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non-fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities BIOS Settings V’s OS Settings 5 Though many options such as power management and display settings may be set in the BIOS, these are usually best set in your OS (e.g. Windows). Older OS’s such as DOS etc. may still rely entirely on the setup information from the BIOS. “Plug-n-Play” OS’s, such as the various Windows systems, may override these settings with the settings from the system’s Control Panel.
BIOS Utilities Working with the Menu Bar You can use the mouse to navigate around the various menus and submenus of the SCU, or alternatively, you can use the following key combinations: Keys Action Table 5 - 1 Alt Activates the menu bar SCU Menu Navigation Keys Left arrow/Right arrow → ← Type the highlighted letters Selects an option in the menu bar Left mouse button Down arrow ↓ Spacebar Enter Opens the pull-down menu bar options Right mouse button Esc Cancels the action Working with the Menu
BIOS Utilities Working with the Pull-Down Menu Table 5 - 2 Pull-Down Menu Keys 5 Once your desired menu bar item is highlighted, press Enter or left-click with the mouse to see the pull-down menu items.
BIOS Utilities Working with Sub-Menus Some pull-down menu options have an arrow to the right of the entry which indicates a sub-menu is available. Choose these sub-menus by pressing Enter and the screen will be displayed.
BIOS Utilities Startup Menu Insyde Software SCU For Intel chipset Startup Figure 5 - 2 Startup Menu 5 Aug 27, 2003 9:40:02 am Memory Disks Components Power Exit Date and Time Devices √ Fast Boot Floppy Drive A = 1.
BIOS Utilities Boot Device (Startup Menu) Specify which device your computer should look on for an operating system by priority. The default setting for the first boot device is Diskette A (external floppy disk), the second boot device is Hard Disk C (internal hard disk), the third boot device is the CD-ROM Drive (external CD device) and the fourth boot device is PXE LAN (network boot). You may also set the computer to boot from the USB HDD (external USB hard disk ).
BIOS Utilities Enable Power On Beep (Startup Menu) Enable or disable (disabled by default) the beep when the computer “boots up”. Password Warning 5 If you choose to set a boot password, NEVER forget your password. Display OEM logo (Startup Menu) Enable or disable (enabled by default) the display of the OEM logo (if applicable) during the POST process. The consequences of this could be serious.
BIOS Utilities Memory Menu Insyde Software SCU For Intel chipset Aug 29, 2003 6:40:02 am Figure 5 - 3 Startup Memory Disks Components Power Exit DevicVGA Shared Memory Hard D Drive C Memory Menu System = 20005MB VGA Shared Memory ock = 1400MHz VGA Shared Memory Size ( ) 8MB ( ) 16MB (·) 32MB Cancel 5 ed d ed d RA AM A Cache (E Ext) E = 640 KB = 252928 KB = 64 KB = 320 KB = 253952 KB = 1024 KB Press (Tab) key to select a control. button or key accept entries.
BIOS Utilities OK Disks Menu Insyde Software SCU For Intel chipset Figure 5 - 4 Disks Menu (IDE Settings) Aug 27, 2003 6:40:02 am Startup Memory Disks Components Power Exit IDE Settings Devices System _ Virus Alert Hard Dri ive C i = 20005M IDE Settings CPU Cl ck Primary ATAPI Primary HDD [X] Drive Enabled [X] Multiple Sector Mode [X] PIO Mode = 1000M MHz M [ ] Drive Enabled [X] PIO Mode Memory 5 IDE UDMA-33/66/100 Function : Enable IDE 32Bit I/O : Enable OK Base Extended Shado
BIOS Utilities Components Menu Insyde Software SCU For Intel chipset Startup Memory Disks Components COM Ports _ Keyboard Numlock = 20 0Keyboard 0 Repeat Keyboard Repeat _ Devices Hard Drive C Aug 29, 2003 6:40:02 am Figure 5 - 5 Components Menu Power Exit System CPU Clock = 1400MHz COM Ports COM A I/O Settings: ( ( ( ( ( ) ) ) ) ) . None COM 1, COM 2, COM 3, COM 4, 3F8, 2F8, 3E8, 2E8, IRQ IRQ IRQ IRQ 4 3 4 3 COM B I/O Settings: ( ( ( ( ( ) None ) COM 1, COM 2, ) COM 3, ) COM 4, .
BIOS Utilities Keyboard Numlock (Components Menu) Enable this mode to start the computer up with Number Lock enabled. Keyboard Repeat (Components Menu) Change the keyboard repeat rate and key delay from this menu.
BIOS Utilities Power Menu Insyde Software SCU For Intel chipset Startup Memory Disks Components Power √ Enable Devices Hard Drive C Aug 29, 2003 6:40:02 am = 30007 MB _ _ _ √ Figure 5 - 6 Power Menu Exit Power Saving System Low Power SavingSaving Medium Power Saving CPU Clock High Power Saving Customize = 600 MHz CPU SpeedStep Controls √ Turn on power for wireless devices 5 Memory Base Extended Shadow Reserved Total RAM Cache (Ext) = 640 KB = 252928 KB = 64 KB = 320 KB = 253952 KB = 102
BIOS Utilities CPU SpeedStep Controls & CPU Performance 5 The settings for CPU SpeedStep Controls will have an affect on the CPU’s speed and performance (in order to save power under certain conditions). See “Intel CPU SpeedStep Controls” on page A - 3 for more details on how the settings control the CPU speed and performance.
BIOS Utilities Exit Menu Insyde Software SCU For Intel chipset Aug 29, 2003 6:40:02 am Exit Menu Startup Memory Disks Components Power Exit Devices Hard Drive C = 30007 MB Figure 5 - 7 System Save and Exit Exit (No Save) CPU Clock Default Settings Restore Settings 000MHz = 10 5 Memory Base Extended Shadow Reserved Total RAM Cache (Ext) = 640 KB = 252928 KB = 64 KB = 320 KB = 253952 KB = 1024 KB Save current settings and return to previous work Save and Exit (Exit Menu) This option allo
BIOS Utilities Exit (No Save) - (Exit Menu) This option allows you to exit the SCU without saving any changes made. Default Settings (Exit Menu) This option allows you to reset the SCU settings to the original defaults before any changes were made to the system. 5 Restore Settings (Exit Menu) This option will allow you to restore the SCU settings to the last changes you had made.
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. 6 - 2 Overview When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. Battery Removal Process 1. 2. 3. 4. 5. Turn the computer off, and turn it over. Locate the battery bay as highlighted in Figure 6 - 1. Slide the battery lock in the direction of the arrow 1 . Slide the battery lock in the direction of the arrow 2 , and hold it in place.
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CDROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 4. 5. 6. Lift the hard disk assembly out of the computer. Remove screws 1 - 4 from the hard disk case and remove the hard disk. Reverse the process to install the new hard disk.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SO-DIMM) - DDR 266 MHz - type memory modules. The main memory can be expanded up to 1024MB. The SO-DIMMs supported are 256MB, and 512MB in size, and the total memory size is automatically detected by the POST routine once you turn on your computer. Memory Upgrade Process 1. 2. 6 Turn off the computer, and turn it over and remove the battery.
Upgrading The Computer 3. Gently pull the two release latches on the sides of the memory socket in the direction of the arrows ( 1 & 2 in Figure 6 - 5). Contact Warning Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. 3 1 4. 5. 6. 7. 8. 9. 2 The module 3 will pop-up, and you can remove it.
Upgrading The Computer Warranty The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 6 Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
Troubleshooting Chapter 7: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power Indicators (see “LED Power Indicators” on page 2 - 5) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. 7 • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Power Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED indicator , is blinking orange and/or a beeping sound is heard. Low Battery. Plug in the AC power source.
Troubleshooting Problem The computer feels too hot. Possible Cause - Solution Make sure the computer is properly ventilated and the vents/fan intakes are not blocked (see “Overheating” on page 1 - 16). If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface. Make sure you’re using the correct adapter.
Troubleshooting Display Problem Nothing appears on screen. Possible Cause - Solution The system is in a power saving mode. Toggle the sleep/resume key combination, Fn + F4 (see “The Keyboard” on page 2 - 17). \ The computer is set for a different display. Toggle the screen display key combination, Fn + F7. If an external monitor is connected, turn it on. The screen saver is activated. Press any key or touch the TouchPad. No image appears on the external monitor I have plugged in and powered on.
Troubleshooting Boot Password Problem You forget the boot password. Possible Cause - Solution If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. 7 Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Audio Problem Possible Cause - Solution The sound cannot be heard or the volume is very low. The volume might be set too low. Check the volume control in the Volume Control Panel in the Windows taskbar, or use the key combination Fn + F5 and F6 (see “The Function Keys” on page 2 - 17) to adjust. The sound cannot be heard when playing an audio CD in an external USB CD device in the Windows 2000 OS. The digital CD audio needs to be enabled.
Troubleshooting CD Device (Optional) Problem 7 Possible Cause - Solution The compact disc cannot be read. The compact disc is dirty. Clean it with a CD-ROM cleaner kit. The compact disc tray will not open when there is a disc in the tray. The compact disc is not correctly placed in the tray. Gently try to remove the disc using the eject hole (see “Loading CDs or DVDs” on page 2 - 11). The system cannot read from the optional CD/ DVD device. The system cannot not read from the optional USB 2.
Troubleshooting Keyboard and Mouse Problem Unwelcome numbers appear when typing. Possible Cause - Solution If the LED is lit, then Num Lock is turned ON. Press and release the Fn & Num Lk key combination (see “Numeric Keypad” on page 2 - 18). Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work.
Troubleshooting Operation 7 Problem Possible Cause - Solution The system performance appears to be getting slower. The system’s power saving features have reduced CPU performance in order to save power. The Power Schemes setting in Windows, or the Intel CPU SpeedStep settings can be configured to reduce CPU speed and performance in order to save power. See “Power Schemes” on page 3 - 19 and “Advanced Power Saving” on page A - 1 for more information on adjusting the settings.
Appendix A: Advanced Power Saving This Appendix contains information on Power Schemes and how they affect the computer’s CPU performance, and information on Intel CPU Speed Step controls.
Windows Control Policies Constant ~ CPU’s performance always runs at lowest level Adaptive ~ CPU’s performance will be adjusted as demanded by the system A Degrade ~ CPU’s performance starts at lowest level and reduces as battery discharges None ~ CPU’s performance always runs at the highest available performance state Table A - 1 Power Scheme Control Policies A- 2 Power Schemes & Processor Performance Windows defines four control policies (see sidebar) used with each power scheme.
Intel CPU SpeedStep Controls Additional controls are available to support the Intel Pentium M processor’s mobile power management features. (It is not necessary to download and run the updated driver if you have an Intel Celeron M processor, however Table A-3 on page A - 8 lists the CPU SpeedStep settings for Celeron M processors.) These controls may be adjusted in the Intel CPU SpeedStep settings in the BIOS.
Checking the Processor Driver Version 1. If you can see the My Computer icon on your desktop (if you cannot see the My Computer icon go to step 2) click on it once to select it, then right-click it to make the sub-menu appear and scroll down to Properties and click on it (go to step 3). 2. If you cannot see the My Computer icon click Start (menu), then point to (but don’t click just highlight it) My Computer.
Figure A - 1 Processor Driver Version (WinXP SP1) Updated driver If you do not see the suffix gv3.sys you will need to download and install the driver (see the instructions on page A - 3). When the driver is downloaded follow the two part instructions on the following page to install and run the driver (you will need to Unzip the contents of the Zip file to a location on your hard disk).
Installing the Driver CPU Performance with SpeedStep A The CPU SpeedStep options will adjust the speed of the CPU according to the setting in the BIOS, and in some cases this will reduce the CPU performance in order to conserve power consumption (generally speaking the higher the speed a CPU runs, the more power it will consume). You will need to set the CPU SpeedStep settings (and the Windows Power Scheme settings) in order to gain a balance between good performance and power saving. A- 6 1.
CPU SpeedStep Settings for Pentium M Processors Performance Mode Always Battery Optimized Mode Always Automatically Switch Windows 2000 or Windows XP with Basic Service Pack 1 Power Source CPU Speed Windows XP Service Pack 1 with updated Driver Power Source CPU Speed 600MHz ~ Max AC In CPU Max Speed AC In Battery (not low) 1300MHz Battery (not low) 600MHz ~ 1300MHz Low Battery 600MHz Low Battery 600MHz AC In 600MHz AC In 600MHz Battery (not low) 600MHz Battery (not low) 600MHz Lo
CPU SpeedStep Control Settings A You can adjust the SpeedStep control settings from the BIOS (see “CPU SpeedStep Controls (Power Menu)” on page 5 - 16). The default BIOS setting is Automatically Switch. However if the CPU settings are at the maximum speed, the CPU speed will still be affected by the Windows Power Scheme setting (this may also adjust the CPU speed).
Appendix B: Model A Specifications Feature Processor Types Specification Intel Pentium® M Processor (478-pin) MicroFCPGA Package Intel Pentium® M Processor (478-pin) MicroFCPGA Package Intel Celeron® M Processor (478-pin) MicroFCPGA Package (µ0.13) 0.13 Micron Process Technology, 1MB On-Die L2 Cache & 400MHz Front Side Bus 1.3/ 1.4/ 1.5/ 1.6/ 1.7 GHz (90nm) 90 Nanometer Process Technology, 2MB On-Die L2 Cache & 400MHz Processor System Bus - 1.7/ 1.8/ 1.9 GHz (µ0.13) 0.
Feature Specification Display Intel Chipset 855GM Integrated Graphics Shared Video Memory Architecture Supporting up to 32MB (Default Setting 32MB) Storage Easy Changeable 2.5" 9.5 mm (h) IDE HDD Supporting Ultra DMA 66/100 Audio Integrated Direct Sound Audio Compliant with AC’97 2.
Feature Specification Interface & Communication Two USB 2.0/1.1 Ports One Stereo Headphone-Out Jack One Monaural Microphone-In Jack One RJ-11 (V.90 K56flex™) Jack for Fax/ Modem MDC Modem Module Supporting Wake On Ring One RJ-45 Jack for 100M (Max) Fast Ethernet Intel Pro 2100 (802.11b) Mini PCI Wireless LAN Module One External (VGA) Monitor Port One DC-in Jack One Infrared FIR, IrDA 1.1 Transceiver One Type II PCMCIA 3.3V/5V Socket Supporting CardBus Power Management Supports ACPI v1.
Feature Optional Specification PC Camera (factory option) Smart Lithium-Ion Battery Pack) Standard - 1800mAH x 6 cells (40W) Optional - 1800mAH x 8 cells (53W) External FDD with USB Interface External Slim Optical Drive with One of the Following Options: CD-ROM DVD-ROM CD-RW Combo DVD-RW DVD+RW Handwriting Application Car Adapter B B- 4
Appendix C: Model B Specifications Feature Processor Types Specification Intel Pentium® M Processor (478-pin) MicroFCPGA Package Intel Pentium® M Processor (478-pin) MicroFCPGA Package Intel Celeron® M Processor (478-pin) MicroFCPGA Package (µ0.13) 0.13 Micron Process Technology, 1MB On-Die L2 Cache & 400MHz Front Side Bus 1.3/ 1.4/ 1.5/ 1.6/ 1.7 GHz (90nm) 90 Nanometer Process Technology, 2MB On-Die L2 Cache & 400MHz Processor System Bus - 1.7/ 1.8/ 1.9 GHz (µ0.13) 0.
Feature Specification Display Intel Chipset 855GM Integrated Graphics Shared Video Memory Architecture Supporting up to 32MB (Default Setting 32MB) Storage Easy Changeable 2.5" 9.5 mm (h) IDE HDD Supporting Ultra DMA 66/100 Audio Integrated Direct Sound Audio Compliant with AC’97 2.
Feature Specification Interface & Communication Two USB 2.0/1.1 Ports One Stereo Headphone-Out Jack One Monaural Microphone-In Jack One RJ-11 (V.90 K56flex™) Jack for Fax/ Modem MDC Modem Module Supporting Wake On Ring One RJ-45 Jack for 100M (Max) Fast Ethernet Intel Pro 2100 (802.11b) Mini PCI Wireless LAN Module One External (VGA) Monitor Port One DC-in Jack One Infrared FIR, IrDA 1.1 Transceiver One Type II PCMCIA 3.3V/5V Socket Supporting CardBus Power Management Supports ACPI v1.
Feature Optional Specification PC Camera (factory option) Smart Lithium-Ion Battery Pack) Standard - 1800mAH x 6 cells (40W) Optional - 1800mAH x 8 cells (53W) External FDD with USB Interface External Slim Optical Drive with One of the Following Options: CD-ROM DVD-ROM CD-RW Combo DVD-RW DVD+RW Handwriting Application Car Adapter C C- 4
