V12.1.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. 2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged. 3. Avoid interference.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord). You must also remove your battery in order to prevent accidentally turning the machine on. Before removing the battery disconnect the AC/DC adapter from the computer.
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern. • Use proper handling procedures when using polymer batteries.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer, use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Ergonomics We designed your Multimedia PC system to be functional as well as attractive. To get most out of it, here are some suggestions on how to position and use the computer: • The top third of the LCD (screen) should be at eye-level or slightly below. • The LCD should be at least 18"/45cm. directly in front of you. • If the screen resolution makes you strain to read, then adjust the resolution to something more comfortable (see “Video Features” on page 1 - 18).
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Wall Mounting Information The computer may be mounted on a wall for display. The system meets VESA MIS-D Standard (100mm * 100mm) for wall mounting. However if you intend to wall mount the system please contact your service center for information in order to avoid personal injury, or damage to the computer.
Preface Contents Notice .............................................................................................................................................................I EuP-Standby and Off Mode Power Consumption Statement: ..................................................................... II FCC Statement ............................................................................................................................................IV FCC RF Radiation Exposure Statement: .......
Preface Tilting the LCD Screen ..............................................................................................................................1-6 Buttons & LED Indicators .........................................................................................................................1-8 On Screen Display Indicators/Buttons .......................................................................................................1-9 System Map: Left View ...................................
Preface ExpressCard Slot .......................................................................................................................................2-7 Inserting and Removing ExpressCards ......................................................................................................2-7 Audio Features ...........................................................................................................................................2-8 Setup for Audio Recording ......................
Preface New Battery .............................................................................................................................................3-13 Recharging the Battery with the AC/DC Adapter ...................................................................................3-13 Proper handling of the Battery Pack ........................................................................................................3-14 Battery FAQ .......................................................
Preface Optional Drivers ........................................................................................................................................4-9 BIOS Utilities Overview ....................................................................................................................................................5-1 The Setup Utility ........................................................................................................................................
Preface Super IO Configuration (Advanced Menu) ...............................................................................................5-9 Security Menu ..........................................................................................................................................5-10 Password on boot (Security Menu) ..........................................................................................................5-10 Set Supervisor Password (Security Menu) .........................
Preface Removing the 3.5" (88.9mm) HDD .........................................................................................................6-10 Replacing the Brackets & Screws in the 3.5" (88.9mm) HDD ...............................................................6-12 Removing the 2.5" (63.5mm) HDD or SSD ............................................................................................6-14 Upgrading the Optical (CD/DVD) Device Drive ...........................................................
Preface Intel® Wireless Music Driver Installation ...............................................................................................7-32 Intel® WiDi Application Configuration ..................................................................................................7-33 Bluetooth & WLAN Combo Module ......................................................................................................7-36 3rd Party Bluetooth (V4.0) Combo Driver Installation ...............................
Preface Computer Ports and Jacks .........................................................................................................................A-2 Card Reader Port .......................................................................................................................................A-2 DC-In Jack ................................................................................................................................................A-2 HDMI-In Port ..........................
Preface HDMI Audio Configuration ...................................................................................................................B-10 Processor ...................................................................................................................................................C-2 Core Logic ................................................................................................................................................C-2 Display ...............................
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, Multi-in-1 card reader, ExpressCard/34/54) Audio & Printer. • Chapter 3 The computer’s power saving options.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you. Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide Not Included Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g.
1 Quick Start Guide System Startup 1. 2. 3. 4. Remove all packing materials, CDs/DVDs and floppy disks etc. Securely attach any peripherals you want to use with the computer to their ports (e.g keyboard and mouse etc.) Attach the AC/DC adapter to the DC-In jack at the rear of the LCD, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter. Push the power button at the front of the computer (along the bottom of the LCD) to turn the computer “on”.
Quick Start Guide System Map: Front View 1. 2. 3. 4. 5. 6. 7. 8.
1 Quick Start Guide Tilting the LCD Screen It is possible to tilt the LCD screen in order to get the best possible viewing angle of the screen without glare etc. 1. Place one hand at the top of the computer 1 , and use the other to open the stand 2 to an angle of around 15 degrees from the vertical position (the stand will allow you to adjust to the appropriate angle if you pull it out and let it spring back). Adjust the stand to tilt the computer to 15° from the vertical position.
Quick Start Guide 2. 3. Apply pressure with one hand at the top (at point 3 ) of the computer (while holding on to the side with the other hand) to carefully push the LCD screen down in order to tilt it to the appropriate viewing angle (up to 50 degrees from the vertical position). Use one hand at the top of the computer (while holding on to the side with the other hand) to move the computer back to the original position.
1 Quick Start Guide Buttons & LED Indicators The buttons located under the front panel icons allow you to make screen and input adjustments.
Quick Start Guide On Screen Display Indicators/Buttons Press the function menu button for about two seconds (see Table 1 - 1, on page 1 - 8) to bring up the On Screen Display. The OSD provides visual indicators for brightness, volume, camera power toggle and WLAN/ Bluetooth power toggle (the camera, WLAN and Bluetooth power indicators will only display if the modules are included in your purchase configuration) when the Hotkey AP is installed (see page 4 - 6).
1 Quick Start Guide Figure 1 - 6 Left View 1. 2. 3. 4. 5. 6. Stand Multi-in-1 Card Reader ExpressCard Slot (see page 2 - 7) 2 * USB 3.0 Ports HDMI-in Port HDMI-Out Port System Map: Left View HDMI-In Port Note that the HDMI-In Port supports video and audio signals from attached HDMI devices.
Quick Start Guide HDMI-In Port This computer features an HDMI (High-Definition Multimedia Interface) input port that allows you to display external sources such as Blu-ray players, DVDs, set top boxes and games consoles etc. on your computer screen. The computer itself does not need to be powered on to display video and audio from external HDMI input sources.
1 Quick Start Guide The following table indicates the functions when an HDMI cable is plugged in to the HDMI-In port.
Quick Start Guide System Map: Right View Figure 1 - 7 - Right View 1. 2. 3. 4. 5. Optical Device Drive Bay (for CD/DVD Device - see page 2 - 3 Headphone-Out Jack Microphone-In Jack USB 2.0 Port Stand 2 Changing DVD Regional Codes 3 Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.
1 Quick Start Guide Figure 1 - 8 Rear View 1. Rear Component Cover 2. Stand 3. Vent/Fan Intake 4. Carrying Handle Area 5. USB Wireless Transceiver Cover (for Optional RF Keyboard & Mouse Kit) 6. Security Lock Slot 7. Battery 8. 2 * RS-232 Serial Ports 9. PS/2 Port (keyboard) 10.PS/2 Port (mouse) 11.DC-In Jack 12.2 * USB Ports 13.
Quick Start Guide Optional Keyboard & Mouse Kit There is an optional RF wireless USB keyboard and mouse kit available for this computer series. A USB port located at the bottom of the rear cover (see “System Map: Rear View” on page 1 - 14) is designed to house the transceiver for the USB wireless keyboard & mouse kit. See “Wireless Keyboard & Mouse USB Transceiver” on page 1 - 16 for more information.
1 Quick Start Guide USB Port for Wireless Transceiver Note that the USB port for the wireless transceiver is designed specifically for the optional RF keyboard and mouse kit supplied with this model only. Wireless Keyboard & Mouse USB Transceiver If your purchase includes the optional wireless keyboard & mouse kit you can use the USB port located at the bottom left of the rear cover to house the USB transceiver (do not use this port for any other device, see sidebar). 1.
Quick Start Guide Windows 7 Start Menu & Control Panel Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
1 Quick Start Guide Video Features You can configure display options from the Display (Control Panel) and Screen Resolution in Windows. For more detailed video information see Chapter B“Intel Video Driver Controls” from page B - 1. To access Display (Control Panel) and Screen Resolution in Windows: 1. 2. 3. Click Start and click Control Panel. Click Display (icon) - In the Appearance and Personalization category. Click Adjust Screen Resolution/Adjust resolution. Right-Click Desktop 1. 1 2.
Quick Start Guide To access the Intel(R) Graphics Media Accelerator Driver for mobile control panel: 1. 2. Click Advanced settings 3 (Figure 1 - 12 on page 1 - 18) in the Screen Resolution control panel in Windows. Click the Intel(R)... tab and click Graphics Properties (button) 4 (Figure 1 - 13 on page 1 - 19) . OR 3. Right-click the desktop and select Graphics Properties from the menu. OR 4. Click the icon in the taskbar and select Graphics Properties from the menu.
1 Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 17) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, display and sleep mode from the left menu. Note that the power saver plan may have an affect on computer performance.
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • Hard Disk Drive Optical (CD/DVD) Device Multi-in-1 Card Reader ExpressCard Slot Audio Features Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" or 3.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 13).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes To change the DVD regional codes: 1. 2. 3. Go to the Control Panel Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.
Features & Components 2 Card Reader Cover Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. Multi-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards). • Align the ExpressCard with the slot and push it in until it locks into place. • To remove an ExpressCard, simply press the card to eject it. ExpressCard Slot Cover Make sure you keep the cover in the ExpressCard slot when not in use.
Features & Components 2 Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer). Click the volume icon in the notification area to check the setting. Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the notification area/control panel (right-click the taskbar notification area icon to bring up an audio menu).
Features & Components Setup for Audio Recording 2 To record audio sources on your computer at optimum quality follow the instructions below: 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel) and make sure you are in Classic View. Click Realtek HD Audio Manager (or right-click the taskbar icon and select Sound Manager).
Features & Components 2 2 - 10
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system. This chapter covers: • • • • • Turning On the Computer Power Plans Power-Saving States Configuring the Power Buttons Energy Star Power Saving OS Note Power management functions will vary slightly depending on your operating system.
Power Management The Power Sources The computer can be powered by either the AC/DC adapter or a battery pack. 3 AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-In jack at the rear of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Adjust the LCD to a comfortable viewing angle.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management Power-Saving States 3 You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection It is recommended that you enable a password on wake up in order to protect your data. Configuring the Power Buttons The power button may be set to send the computer in to either Sleep or Hibernate. In Sleep, the LED will blink green. In Hibernate the LED will be orange. If only the display is turned off, the LED will remain green. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (see your keyboard documentation).
Power Management Energy Star Power Saving This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. If you want to enable Energy Star power saving then follow these instructions: 3 1. 2. 3. Right-click the taskbar icon (see sidebar). Select Power Conservation Modes. Select Energy Star to use the Energy Star power management and override other power saving settings.
Power Management Battery Information Follow these simple guidelines to get the best use out of your battery. Low Battery Warning Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure 3 - 1 on page 3 - 4).
Power Management 3 Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display.
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery” on page 6 - 4.
Power Management Proper handling of the Battery Pack 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. • DO NOT disassemble the battery pack under any circumstances. • DO NOT expose the battery to fire or high temperatures, it may explode. • DO NOT connect the metal terminals (+, -) to each other.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 1. 2. 3 Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management 3 How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive and click Install Drivers/Option Drivers (button). 4 Follow the instructions to install the driver. Alternatively click Start, navigate (Browse..) to the executable file and then follow the manual setup instructions. 1. 2. 3.
Drivers & Utilities Driver for Windows 7 with Service Pack 1 Page # Driver for Windows 7 with Service Pack 1 Page # Chipset Page 4 - 6 PC Camera Module Page 7 - 2 Video Page 4 - 6 Wireless LAN Module Page 7 - 10 LAN Page 4 - 6 Bluetooth & WLAN Combo Module Page 7 - 36 ExpressCard/Card Reader Page 4 - 6 Trusted Platform (Security) Module Page 7 - 43 Hotkey AP Page 4 - 6 USB 3.
Drivers & Utilities Manual Driver Installation Click Browse CD/DVD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder. 4 Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See “Windows 7 Update” on page 4 - 8 for instructions.
Drivers & Utilities User Account Control New Hardware Found If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as directed. If you see the message “New Hardware Found” during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure.
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc into your DVD drive and click Install Drivers (button). 4 Chipset 1. Click 1.Install Chipset Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. Video 1. Click 2.Install VGA Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. 4 - 6 Driver Installation LAN 1. Click 3.Install LAN Driver > Yes. 2.
Drivers & Utilities USB 3.0 1. Click 6.Install USB 3.0 Driver > Yes. 2. Choose the language you prefer and click OK. 3. Click Next. 4. Click the button to accept the license agreement and click Next. 5. Click Finish. MEI Driver 1. Click 7.Install MEI Driver > Yes. 2. Click Next > Yes > Next. 3. Click Finish to restart the computer. Note that after installing the audio driver the system will not return to the Drivers Installer screen.
Drivers & Utilities Windows Experience Index After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experience Index: 4 1. Click Start, and click Control Panel. 2. Click Performance Information and Tools (System and Security > System > Check the Windows Experience Index). 3. Click “Rate this computer”. 4. The computer will take a few minutes to assess the system performance. 5. Close the control panel.
Drivers & Utilities Optional Drivers See the pages indicated in Table 4 - 1, on page 4 - 3 for the driver installation procedures for any modules included in your purchase option. Insert the Device Drivers & Utilities + User’s Manual disc and click Option Drivers (button) to access the optional driver menu.
Drivers & Utilities 4 4 - 10
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing.
BIOS Utilities The Setup Utility Each time you turn on the computer the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). 5 As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup. If there are no problems, the Setup prompt will disappear and the system will load the operating system.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized distributor/supplier as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities Setup Menus 5 The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configuration appropriate for your model and options. Setup Screens The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup.
BIOS Utilities Main Menu Figure 5 - 2 Main Menu System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed. 5 MB Series / BIOS Revision / KBC/EC firmware Revision This item contains information on the BIOS version etc., and is not user configurable.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu 5 Advanced Chipset Control (Advanced Menu) The sub-menu here allows you to adjust the Bluetooth Power Setting and Total Graphics Memory.
BIOS Utilities SATA Mode Selection 5 If you have installed the Windows 7 operating system with either IDE or AHCI mode enabled, DO NOT disable the set mode (if you wish to disable the set mode you will need to reinstall the Windows 7 OS). Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) You can adjust the Bluetooth module power setting to your preference. The default setting (Disabled) will see the Bluetooth module powered off when the system is started up or restarted.
BIOS Utilities Boot Logo (Advanced Menu) Use this menu item to enable/disable the Boot Logo screen at system startup. If you disable the Boot Logo you will not see the F2 Enter Setup or F7 Boot Options prompts on the screen, however you can still press these keys, while the boot screen is displayed, to perform the Enter Setup or Boot Option functions. Power On Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up.
BIOS Utilities Security Menu Security Menu 5 The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Figure 5 - 4 Security Menu Password on boot (Security Menu) Specify whether or not a password should be entered to boot the computer (you may only set a password on boot if a supervisor password is enabled).
BIOS Utilities Set Supervisor Password (Security Menu) You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility). If you set a supervisor password you can then add a user password. Set User Password (Security Menu) You can set a password for user mode access to the Aptio Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below).
BIOS Utilities Secure Boot (Advanced Menu) Enable/disable Secure Boot from this menu. The Secure Boot specification provides a clean interface between operating systems and platform firmware at boot time. In contrast to BIOS, Secure Boot defines a set of standard boot and runtime services. Secure Boot may be set to Standard (with a fixed Secure Boot policy), or Custom (which allows changes to execution policy and Secure Boot databases).
BIOS Utilities Boot Menu Figure 5 - 5 Boot Menu BIOS Screens Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS. When you turn the computer on it will look for an operating system (e.g. Windows 7) from the devices listed in this menu, and in this priority order. If it cannot find the operating system on that device, it will try to load it from the next device in the order specified in the Boot Option Priorities.
BIOS Utilities Fast Boot / UEFI Boot (Boot Menu) Fast Boot will enable a boot with the minimal set of devices required (the sub-menus will allow you to choose to skip the EFI VGA driver, USB devices and/or PS/2 devices. You can also choose to enable/disable boot from UEFI devices. Boot Option Priorities (Boot Menu) Use the arrow keys to move up and down the menu, and press Enter to select a device from the Boot Option # list.
BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu 5 Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose Load Setup Defaults to restore the original Setup defaults and return the Setup to its original state, and erase any previous changes you have made in a previous session.
BIOS Utilities 5 5 - 16
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord). These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. Before removing the battery disconnect the AC/ DC adapter from the computer first. 1. 2. 3. 4. 5. Turn the computer off, remove the AC/DC adapter and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place.
Upgrading The Computer 6. 7. Raise the battery up out of the bay 6 Remove the battery 7 . .
Upgrading The Computer Inserting the Battery 1. 2. 3. 4. Insert the battery 1 at an angle and slide it firmly into the battery bay until connected. Insert the battery bay cover by angling it to fit on the right 2 at first, and then click the left side into place 3 . Slide the cover in the direction of the arrow 4 until the top marker of the battery cover icon 5 is aligned with the marker on the side of the computer 6 . Slide the latches 7 towards the lock symbols to lock the cover in place.
Upgrading The Computer Removing the Rear Component Cover Before undertaking any upgrade procedure it is necessary to remove the rear cover component cover to access the components. 1. 2. 3. 6 Turn off the computer and disconnect all cables and peripherals. Carefully place the computer flat with the LCD facing down (make sure you cover the LCD to avoid scratches) so that you may access the rear cover. Remove screws 1 & 2 .
Upgrading The Computer 4. Slide the rear cover up in the direction of the arrow 3 , until the bottom marker of the rear cover icon is aligned with the marker on the side of the computer 4 . 4 4 4 4 3 Figure 6 - 5 Rear Cover Unlock 6 5. Carefully remove the rear cover 5 , and set it aside.
Upgrading The Computer Inserting the Rear Cover 1. 2. Carefully slide the rear cover on to the computer until the marker of the rear cover icon is aligned with the marker on the side of the computer 1 . Replace screws 2 & 3 .
Upgrading The Computer Upgrading the Hard Disk Drive/SSD The hard disk drive can be taken out to accommodate other 2.5"(63.5mm) or 3.5"(88.9mm) serial (SATA) hard disk drives (see “Storage” on page C - 3), or a Solid State Drive (SSD). Follow your operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in “Driver Installation Procedure” on page 4 - 6), when setting up a new hard disk.
Upgrading The Computer Removing the 3.5" (88.9mm) HDD 1. 2. 3. 4. 5. Remove the battery and rear cover (see pages 6 - 3 & 6 - 5). The hard disk is located at point 1 . Remove screws 2 - 5 from the hard disk bracket. Slide the HDD assembly in the direction of arrow 6 . Life the HDD assembly 7 out of the computer. 2 3 4 5 6 Figure 6 - 8 3.
Upgrading The Computer 6. 7. Remove screws 8 - 13 from the hard disk bracket Remove the left and right side brackets from the HDD. Screwdriver Types 8 10 13 12 9 11 Make sure you use a small manual screwdriver, and not an electrical screwdriver, in the course of the upgrade/disassembly procedures outlined here, due to the delicate nature of the screws. Figure 6 - 9 3.
Upgrading The Computer Replacing the Brackets & Screws in the 3.5" (88.9mm) HDD 1. Screw Types 6 Note that screws 1 & 2, and screws 3 -6 are different. Screws 1 & 2 are for the top of the bracket, and screws 3 - 6 are for the side of the bracket. 2. 3. 4. 5. 6. Before replacing the brackets and screws for any new HDD, it is important to note that there are left and right brackets for the side of the assembly, and the screws need to be inserted in the appropriate order.
Upgrading The Computer 7. 8. 9. It is important to set the screws 7 - 10 (for screwing the HDD assembly to the case) in place in the HDD assembly before sliding the assembly into the case. Once the screws are set in place slide the whole assembly including the screws into place as per Figure 6 - 8 on page 6 - 10. Make sure the HDD is connected to the slot and then tighten the four screws and replace the rear component cover and screws.
Upgrading The Computer Removing the 2.5" (63.5mm) HDD or SSD Foam Insert for SSDs 6 Note that if your computer contains an SSD in the bracket then a foam insert will be supplied. Make sure you have the foam inserted when installing an SSD to this bracket (see “Removing the SSD from the Bracket.” on page 6 16). 1. 2. 3. 4. Remove the battery and rear cover (see pages 6 - 3 & 6 - 5). The hard disk or solid state drive is located at point 1 .
Upgrading The Computer Removing the 2.5" (63.5mm) HDD from the Bracket. 5. 6. Remove screws 1 & 2 and separate the bracket 3 from the HDD 4 . Reverse the process to install a new hard disk. 4 2 6 Figure 6 - 13 3 2.
Upgrading The Computer Removing the SSD from the Bracket. 1. 2. 3. 4. Remove screws 1 & 2 and separate the bracket and sponge assembly 3 from the HDD 4 . Separate the bracket 5 from the sponge 6 . Make sure you insert the sponge when installing a new HDD. Reverse the process to install a new hard disk.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device Drive 1. 2. 3. 4. Remove the battery and rear cover (see pages 6 - 3 & 6 - 5). The ODD is located at point 1 . Remove the screw 2 , and use a screwdriver to carefully push out the optical device out in the direction of the arrow at point 3 . Reverse the process to install any new optical device.
Upgrading The Computer Contact Warning 6 Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. Upgrading the System Memory (RAM) The computer has two memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDRIII (DDR3) type memory modules (see “Memory” on page C - 2 for details of supported module types).
Upgrading The Computer 3. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 2 & 4 ) in Figure 6 - 17. 2 3 Figure 6 - 17 RAM Module Release 6 2 4. 5. 3 The RAM module will pop-up, and you can remove it. Pull the latches to release the second module if necessary.
Upgrading The Computer 6. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory socket (see sidebar note if you are inserting a single module). Figure 6 - 18 RAM Module Removal 6 Single Memory Module Installation If your computer has a single memory module, then insert the module into the Channel 0 (JDIMM1) socket. In this case this is the upper memory socket (the socket furthest from the mainboard). 7.
Upgrading The Computer Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard. Warranty The CPU is not a user serviceable part. Accessing the CPU in any way, may violate your warranty. Unauthorized tampering with the HDD may also violate your warranty.
Upgrading The Computer 6 6 - 22
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
Modules & Options Latest PC Camera Driver Information 7 Check the Device Drivers & Utilities + User’s Manual disc and any accompanying insert pages, for the latest updated information on the PC Camera driver, which may override the information provided here. PC Camera Module Before installing the driver, make sure the PC Camera is on. Use the On Screen Display button (see page 1 - 9) to toggle power to the PC Camera module.
Modules & Options PC Camera Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Make sure the camera module is on before beginning the installation process (use the On Screen Display to toggle power to the camera module - see page 1 - 9). 3. Click Option Drivers (button). 4. Click 1.Install Webcam Driver > Yes. 5. Click Finish to restart the computer. OR Click Next > Finish. 6.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. 7 Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone (Realtek High Definition Audio) and make sure the item is not disabled. 5. Double-click Microphone (or select Properties from the right-click menu). 6.
Modules & Options Figure 7 - 1 Audio Setup for PC Camera Right-click 7 PC Camera Module 7 - 5
Modules & Options Camera Application The camera application is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format. 1. 2. 3. 7 Run the camera application from the desktop shortcut (it is recommended that you set the capture file before the capture process - see below). Go to the Capture menu heading (if you wish to capture audio check “PC Camera Audio Setup” on page 7 - 4) and select Start Capture.
Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules & Options Latest PC Camera Driver Information 7 Check the Device Drivers & Utilities + User’s Manual disc, and any accompanying insert pages, for the latest updated information on the PC Camera driver, which may override the information provided here, including the figures pictured here. Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3.
Modules & Options Taking Still Pictures The camera application allows you to take still pictures. 1. 2. 3. Run the camera application from the desktop shortcut. Go to Options and select Take Picture. The picture (in JPEG format) will be placed in the Snapshot folder desktop. Snapshot Folder on the The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture.
Modules & Options Wireless LAN Module If you have included an Intel® or 3rd Party module in your purchase option use the On Screen Display button (see page 1 - 9) to toggle power to the Wireless LAN module, and make sure that the module is on before installing the driver. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules.
Modules & Options 3rd Party 802.11b/g/n Driver Installation (for WLAN Module Only) See over for information on installing the drivers for the 3rd party WLAN & Bluetooth combo module. If you see the message “Found New Hardware” click Cancel to close the window. 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. 2. Click Option Drivers (button). 3. Click 2.Install WLAN Driver > Yes. 4.
Modules & Options 3rd Party 802.11b/g/n Driver Installation (for Combo Modules) If you see the message “Found New Hardware” click Cancel to close the window. 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. 2. Click Option Drivers (button). 3. Click 2.Install WLAN Driver > Yes. 4. Click Next. 5. Click Finish to restart the computer (see sidebar for important information).
Modules & Options Intel® WLAN Driver Installation For a standard Intel® WLAN driver installation and configuration choose the Typical Installation below and use the Windows OS for Wireless LAN control (see overleaf). If you want to use Intel® PROSet/Wireless WiFi Connection Utility as your WLAN interface, and/or add Intel® MyWifi Technology (Personal Area Network) see overleaf. Typical Installation: 1. If you see the message “Found New Hardware” click Cancel to close the window. 2.
Modules & Options Custom Installation (for Intel® ProSet and/or Intel® MyWiFi Technology): Note that if you wish to install Intel® MyWiFi you will need to install Microsoft.net Framework 4.0 (or later version) before installing the driver as per the procedure below. To get the Microsoft.net Framework file go to the Microsoft website, search for the file, Download it and then install it. 7 1. If you see the message “Found New Hardware” click Cancel to close the window. 2.
Modules & Options Figure 7 - 3 Install Intel® MyWiFi Technology & Intel® PROSet/Wireless WiFi Connection Utility Wireless LAN Module 7 - 15 7
Modules & Options Network and Sharing Center You can also use the Network and Sharing Center control panel in Windows (Network and Internet) to connect to any available wireless networks. Connecting to a Wireless Network in Windows 7 Make sure the Wireless LAN module is turned on. 1.
Modules & Options 2. 3. 4. You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click “View or change settings in Network and Sharing Center” to access further options for the connection.
Modules & Options Security Enabled Networks 5. 6. Click the taskbar icon to see any currently connected networks. To disconnect from the wireless network you can click the taskbar wireless icon click the active connection and then click Disconnect (button). You should try to make sure that any network you are connecting to is a secure network. 7 Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Connecting to a Wireless Network Using Intel® PROSet Wireless (For Intel® WLAN Modules Only) 1. 2. 3. Make sure the Wireless LAN module is on. Access the Intel® WiFi Connection Utility from the Start menu (Start > All Programs > Intel PROSet Wireless > WiFi Connection Utility). Click to select a network from the found list WiFi network access points, or click Refresh to update the list.
Modules & Options 7 4. 5. Click Connect to connect to the select WiFi network access point. If the access point is encrypted then you will need to enter the password and click OK. 6. 7. 8. You can turn WiFi On/WiFi Off from the button at the bottom of the Utility. To disconnect, select the connected access point and click Disconnect. Select Help from the menu at the top of the utility (or at the bottom right) to bring up the Help menu.
Modules & Options Intel® My WiFi Configuration (For Intel® WLAN Modules Only) Intel® My WiFi Technology (Intel® MWT) uses your WLAN to transform your system into a Wi-Fi Personal Area Network, and enables you wirelessly share your videos, photos, music with other WiFi enabled devices, while still connecting to the Internet through your WiFi wireless connection. Intel® MWT also features a chat function, and offers you the option of being able to create a WiFi hotspot from your computer.
Modules & Options Intel® My WiFi Configuration You can configure the My WiFi settings as follows. 1. 2. 3. 7 Make sure the Wireless LAN module is on. Access the Intel® WiFi Connection Utility from the Start menu (Start > All Programs > Intel PROSet Wireless > Intel(R) My WiFi Dashboard), or click the icon in the notification area of the taskbar (or right-click and select Open Dashboard).
Modules & Options Intel® My WiFi Interface Help Wireless ON/OFF Configuration Options & Preferences Figure 7 - 10 Intel® My WiFi Utility - Interface Your Computer Wireless LAN Module 7 - 23 7
Modules & Options Intel® My WiFi Help Click the Help icon in the dashboard to bring up the Help menu and select and item from the Contents menu to obtain the help information.
Modules & Options Preferences Click the Options icon and select Preferences to configure the options.
Modules & Options Hotspot You can turn the computer into a hotspot to allow other devices to connect to it (and any locally connected devices), and also (if available) the internet. 1. 2. 3. Click the Hotspot icon to turn the Hotspot on. The Hotspot settings tab shows the SSID and password (you will need to enter this information when accessing the Hotspot from the client computer/device). Click OK to close the Hotspot settings.
Modules & Options Finding Devices You can find any Nearby Devices by clicking the Refresh button in the main window. Click again at any time to update the list. If a lot of devices are found they will be listed on multiple pages and you can use the left or right buttons to turn the pages. Sensitivity The Sensitivity controls displays available devices based on their signal strength and proximity e.g decreasing (-) the sensitivity lists only devices closest to the computer’s location.
Modules & Options Favorite Devices The Favorite Devices tab is where you keep devices to which you connect most often, and this is particularly useful in environments where many devices are listed nearby. A favorite device will display the icon . To make any device a favorite just click to select it and select Add Favorite.
Modules & Options Connect to a Device 1. 2. 3. 4. 5. Click the device you want to connect to, and click the connect icon . An invitation will be sent to the target device. The user must then accept the invitation. After the invitation is accepted the connection will be made. Use the Windows Network and Sharing Center to set permissions for viewing and sharing the resources on your computer with another connected computer.
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules & Options Intel® Wireless Display Application The Intel® Wireless Display Application (requires Intel® Centrino WLAN/ Combo module), in conjunction with a compatible video adapter (purchased separately), allows you to display the contents of the notebook display on another display (e.g. HDTV) without the need to have cables stretching across a room. You can then play games, browse the internet, display videos or photo slide shows on your TV/external display without using HDMI or A/V cables.
Modules & Options Intel® WiDi Application Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. 2. Click Option Drivers (button). 3. Click 3.Install WiDi AP > Yes. 4. Click Next. 5. Click the button to accept the license and click Next. 6. Click Finish.
Modules & Options Intel® WiDi Application Configuration 1. 2. 3. Click Start > All Programs > Intel Corporation > Intel(R) Wireless Display > Intel(R) Wireless Display, or double click the icon on the desktop. Click I agree to the terms of this license (button). The application will scan for any connected compatible adapters (or you can click the Scan for available adapters button to enable Intel My WiFi Technology).
Modules & Options 4. 5. 6. Click to select any detected adapters, and click Connect. The system will then prompt you to enter the 4-digit security code which will be displayed on the external TV Screen (or press the connect button on the wireless speaker adapter). Enter the code for the video adapter and click Continue.
Modules & Options 7. 8. You will then be prompted to enter a name for the video adapter and click Continue. Click Finished to complete the setup. Test Audio Adapter To verify a successful audio connection (for Intel® Wireless Music), select the “Test your audio connection” link or select “Finished” to bypass the test. You can select “Play Sample” to play an audio test sample from your adapter to the connected speaker set.
Modules & Options Bluetooth Data Transfer 7 Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported). Therefore if you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process from the computer has been completed.
Modules & Options 3rd Party Bluetooth (V4.0) Combo Driver Installation Note this driver is required for the 3rd Party combo Bluetooth and WLAN module (Bluetooth V4.0) only. 1. Before installing the driver make sure the Bluetooth module is powered on (use the On Screen Display button to toggle power to the module), then insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive.
Modules & Options Intel Bluetooth Combo Driver Installation High Speed Bluetooth Data Transfer 7 The Combination Wireless LAN & Bluetooth module supports high speed data transfer. However to achieve such transfer speeds, both devices must support high speed data transfer. To obtain high speed data transfer make sure that both the WLAN and Bluetooth modules are powered on. Note this driver is required only for the Intel combo Bluetooth and WLAN module only. 1.
Modules & Options Standard Bluetooth Configuration in Windows 7 Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). To Turn the Bluetooth Module On 1. Press the On Screen Display button to power on the Bluetooth module. 2. 3. A Bluetooth icon will appear in the taskbar. You can then do any of the following to access the Bluetooth Devices control panel.
Modules & Options To Add a Bluetooth Device 1. 2. Access the Bluetooth Devices control panel and click Add a device. Double-click the device you want to pair with the computer. 3. On first connection the computer will provide you with a pairing code to be entered onto the device. Pairing Options 7 If a device has been previously connected then the pairing option menu will appear when you attempt subsequent connections.
Modules & Options 4. Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing. Pairing Codes The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection procedure, and may require you to confirm a pairing code is correct on both devices. Follow the onscreen instructions to complete the pairing. 5. 6. 7.
Modules & Options To Change Settings for the Bluetooth Device Bluetooth Help 7 To get help on Bluetooth configuration and settings, select Help and Support from the Start menu. Type Bluetooth in the Search Help box, and select an item from the returned search results to get more information. 1. 2. • • Click the taskbar icon and select Show Bluetooth Devices.
Modules & Options Trusted Platform (Security) Module The TPM security chip allows you to create and manage digital certificates for user and platform authentication. This type of security is usually administered within large enterprises and organizations, and therefore requires implementation by a system administrator before users can access security features. Individual users can use the TPM as an authentication with the fingerprint reader.
Modules & Options Enabling & Activating TPM 1. 2. 3. 4. 5. 6. Restart the computer. Enter the Aptio Setup Utility pressing F2 during the POST/startup. Use the arrow keys to select the Security menu. Select Configuration and press Enter to access the sub-menu. Press Enter to access the Security Device Support menu and select Enable to display the full TPM configuration menu. Select TPM State, press Enter and select Enabled to change the TPM state to enabled.
Modules & Options 8. Select Pending operation, press Enter and select the option you require (if you are initializing TPM you should select Enable Take Ownership). You will then need to press F4 to save the changes and restart the computer. Figure 7 - 25 Pending operation (Enable Take Ownership) 7 9. You can now install the TPM driver (see “Trusted Platform Module (TPM) Driver Installation” on page 7 - 46) and then initialize the TPM.
Modules & Options Trusted Platform Module (TPM) Driver Installation 1. Make sure you have enabled and activated the TPM in the BIOS before installing the driver (if you do not do see the note below). 2. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 3. Click Option Drivers (button). 4. Click 5.Install TPM Driver > Yes. 5. Click Install > Next. 6. Click the button to accept the license and click Next. 7. Click Next > Next > Install. 8.
Modules & Options Initializing TPM 1. 2. 3. 4. 5. Run the application from the Infineon Security Platform Solution > Manage Security Platform item in the Start > Programs menu. Click User Settings (tab) and click Yes, or right-click the icon in the notification area of the taskbar, and select Security Platform Initialization (or click the Security Platform State taskbar bubble).
Modules & Options 6. Help 7. Choose the Security Platform Features you want to use by clicking the appropriate tickbox. Enter a Basic User Password (and re-type to confirm it) and click Next. Right-click the icon in the notification area of the taskbar to bring up the menu to select Help or How to use the Security Platform Features. 7 You can also click the Help button in any of the Infineon Security Platform Settings Tool tabs to bring up specific help topics on each tab.
Modules & Options Infineon Security Platform Settings Tool The Infineon Security Platform Settings Tool allows you to manage and check the TPM state, manage your password information, and to backup and restore the TPM data. As TPM is usually administered within large enterprises and organizations, your system administrator will need to assist you in managing the information here. Menus Note that not all the menus pictured here will be available for access.
Modules & Options User Settings This page allows the settings to be configured for the currently logged in Infineon Security Platform user including the ability to change the password, configure secure e-mail, file and folder encryption and Enhanced Authentication. You can also import or delete certificates protected by the security platform.
Modules & Options Backup Here you can configure backup and restore operations. Backup files contain the computer identification and user identification information which is used to match the machine name and user name with the current machine and user during restoration.
Modules & Options Migration The Migration tab is used to help securely transfer keys and certificates from one platform to another.
Modules & Options Password Reset Use Password Reset to reset basic user passwords when required.
Modules & Options BitLocker BitLocker Drive Encryption can be used in conjunction with the TPM to encrypt data on the disk and is done via the Microsoft BitLocker Control Panel Applet. Click Configure and select a drive to be encrypted and then follow the Wizard to begin the encryption process.
Modules & Options Access the Microsoft BitLocker Drive Encryption control panel applet from the Windows control panel (System and Security).
Modules & Options Advanced Configure all the Security Platform owner and policy settings from the Advanced tab. The settings that can be changed are for the local computer only.
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “Buttons & LED Indicators” on page 1 - 8) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems & Possible Solutions Problem Possible Cause - Solution The Battery LED power indicator , is blinking orange. Low Battery. Plug in the AC power source. If the computer doesn’t start up immediately, turn it off then on again. You are losing battery power too quickly. The system is using too much power. If your OS has a Power Options scheme (see “Power Plans” on page 3 - 4) check its settings.
Troubleshooting Problem Nothing screen. appears Possible Cause - Solution on The system is in a power saving mode. Press the power button or any configured sleep/resume key combination. The screen controls need to be adjusted. Press the brightness buttons to adjust the settings. If you’re connected to an external monitor, make sure it’s plugged in and turned on. You should also check any attached monitor’s own brightness and contrast controls. The screen saver is activated. Press any key on the keyboard.
Troubleshooting Problem Possible Cause - Solution The Optical Disk Drive tray will not open when there is a disc in the tray. The compact disc is not correctly placed in the tray. Gently try to remove the disc using the eject hole (see “Loading Discs” on page 2 - 3). The DVD regional codes can no longer be changed. The code has been changed the maximum 5 times. See “DVD Regional Codes” on page 2 - 5. The DVD will not play. The computer is tilted beyond 50 degrees.
Troubleshooting Problem Possible Cause - Solution The Wireless LAN/ Bluetooth/PC Camera modules cannot be detected. The modules are off. Press the function menu button for about two seconds (see Table 1 - 3, on page 1 - 9) to bring up the On Screen Display. Check the appropriate OSD to see if it is on or off. The Wireless LAN/ Bluetooth/PC Camera modules cannot be configured. The driver(s) for the module(s) have not been installed.
Troubleshooting Bluetooth Connection Problems If you are experiencing problems connecting to some Bluetooth devices (in particular certain mobile phones and headsets) it maybe necessary to download and install the Windows Mobile Device Center software (for Windows Vista and Windows 7). Go to the Microsoft website and search for the Microsoft Windows Device Center Driver for Windows Vista (64-bit or 32-bit) and Windows 7 (64-bit or 32-bit), and then download the driver. 1. 2. 3. 4. 5.
Troubleshooting 6. 7. 8. 8 Right-click Bluetooth Peripheral Device and click on Update Driver Software. Click Browse my computer for driver software. Click Let Me pick from a list of device drivers on my computer. Figure 8 - 2 - Browse my computer.../Let me pick from... 9. Select Bluetooth Radios from the list.
Troubleshooting 10. A list of drivers will appear with Manufacturer on one side and Model in the other. 11. Choose Microsoft Corporation (make sure you choose the full name Microsoft Corporation and do not choose Microsoft - Note that you must have installed the Microsoft Windows Device Center Driver for Microsoft Corporation to appear in the list). 12. Select Windows Mobile-based device support from the Model list. 8 Make sure you select Microsoft Corporation Figure 8 - 4 - Select Device Driver 13.
Troubleshooting 15. The Device Manager should now display the Windows Mobile-based device support under Bluetooth Radios. 16. You will need to repeat the process for any other Bluetooth Peripheral Devices listed under Other Devices.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Computer Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. HDMI-In Port The HDMI-In (High-Definition Multimedia Interface) port allows you to display external sources such as Blu-ray players, DVDs, set top boxes and games consoles etc.
Interface (Ports & Jacks) Item Microphone-In Jack PS/2 Type Keyboard & Mouse Ports Description Plug an external microphone in to this jack to record on your computer. Connect an external PS/2 type mouse or keyboard to these ports. Port Warning The computer can only accept one keyboard at a time. Don’t try to install a USB and a PS/2 keyboard at the same time. Doing so may cause resource conflicts and make the system unstable.
Interface (Ports & Jacks) Item Description Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. USB 2.0/1.1 Ports These USB (Universal Serial Bus) 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Intel Video Driver Controls Appendix B: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 18. DVMT Notes Intel Video Driver Installation Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Video 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click 2.Install VGA Driver > Yes. 3. Click Next > Yes > Next > Next. 4. Click Finish to restart the computer.
Intel Video Driver Controls HDMI-In Port This computer features an HDMI (High-Definition Multimedia Interface) input port that allows you to display external sources such as Blu-ray players, DVDs, set top boxes and games consoles etc. on your computer screen. B Intel® Graphics & Media Control Panel Advanced video configuration options are provided by the Intel® Graphics and Media Control Panel. To access the control panel: 1. 2.
Intel Video Driver Controls You may make changes to any of the graphics properties by clicking the appropriate menu tab on the left of the menu and adjusting the settings on the right. Options & Support Click Options & Support and select an item from the sub-menu to bring up the help and support topics. You will need to be connected to the Internet to access the key resource links. Multiple Display At least one other display must be attached in order to view multiple display selection options.
Intel Video Driver Controls Default Display Mode The initial default display mode when first attaching an external display is set to Extended Desktop Mode. You can use the Intel(R) G&M control panel to adjust this setting. Subsequent to any restart/shutdown or removal of display device, the system will retain the last mode set before the restart/shutdown or removal of display device.
Intel Video Driver Controls Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the external monitor port. To Clone Displays: 1. 2. 3. 4. 5. Attach your display to the HDMI-Out port and turn it on. Go to the Intel(R) G&M control panel and click Display > Multiple Displays. Click Operating Mode and select Clone Displays from the menu. Click Apply, and OK to confirm the settings change. You can switch the Primary/Secondary Display from the menu.
Intel Video Driver Controls To Enable Extended Desktop: Display Settings Extended Desktop 1. 2. 3. 4. Attach your display to the external monitor port and turn it on. Go to the Intel(R) G&M control panel and click Display > Multiple Displays. Click Operating Mode and select Extended Desktop from the menu. Click Apply, and OK to confirm the settings change. You can have different Colors, Screen Area and Monitor Refresh Rates for each display device provided your monitor can support them.
Intel Video Driver Controls Configuring an External Display in Windows 7 You can also use the Screen Resolution control panel in Windows 7 to configure an external display. 1. 2. 3. 4. Attach your display to the external monitor port and turn it on. Go to the Screen resolution control panel (see “Video Features” on page 1 18). Click the Detect button. The computer will then detect any attached displays.
Intel Video Driver Controls 5. You can configure the displays from the Multiple Displays menu. Figure B - 6 Screen Resolution Multiple Display Options (Win 7) B • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s). • Extend these displays - Treats both connected displays as separate devices. • Show desktop only on 1/2 - Only one of your displays is used.
Intel Video Driver Controls Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configuration and modes (this is particularly useful when attaching a projector) in Windows 7. 1. 2. 3. 4. Attach your display to the external monitor port and turn it on. + P key combination. Press the An on-screen menu will pop up.
Intel Video Driver Controls Volume Indicator Click the taskbar volume indicator when an HDMI device is selected, and you will note that the icon at the top of the volume level indicator has changed. HDMI Audio Configuration HDMI (High-Definition Multimedia Interface) carries both audio and video signals. In some cases it will be necessary to go to the Sound control panel and manually configure the HDMI audio output as per the instructions below. 1. 2. 3. 4.
Intel Video Driver Controls 5. 6. Adjust the HDMI settings from the control panel tabs. Click OK to close the Sound control panel.
Intel Video Driver Controls Other Applications If you are using a third party application to play DVDs etc. from any attached DVD device, you will need to consult the application’s documentation to see the appropriate audio configuration (the application must support digital to analog translation). HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device.
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your distributor/supplier for details.
Specifications Processor Intel® Core™ i7-3770S Processor (3.10GHz) 22nm (22 Nanometer) Process Technology, DDR3-1600MHz, 8MB L3 Cache - TDP 65W Intel® Core™ i5-3570S Processor (3.10GHz) 22nm (22 Nanometer) Process Technology, DDR3-1600MHz, 6MB L3 Cache - TDP 65W Intel® Core™ i5-3550S Processor (3.00GHz) 22nm (22 Nanometer) Process Technology, DDR3-1600MHz, 6MB L3 Cache - TDP 65W Intel® Core™ i5-3475S Processor (2.
Specifications Video Adapter Audio Card Reader Intel® Integrated GPU (Intel® HD Graphics / Intel® HD Graphics 2500 / Intel® HD Graphics 4000): Dynamic Frequency Intel® DVMT Shared Memory Architecture up to 1748MB Microsoft DirectX®10 Compatible (Intel® HD Graphics) Microsoft DirectX®11 Compatible (Intel® HD Graphics 2500 / Intel® HD Graphics 4000) High Definition Audio Built-In Microphone 2 Built-In Two 3W Speakers Embedded Multi-In-1 Push-Push Card Reader - MMC/ RS MMC - SD/ Mini SD / SDHC/ SDXC - MS/
Specifications Intel® Centrino® Wireless-N 2230 2*2 (802.11 b/g/n) Half Mini-Card PCIe WLAN + Bluetooth V4.0+HS Combo Module (Factory Option) 802.11b/g/n WLAN Half Mini-Card Module (Factory Option) Combo WLAN (802.11b/g/n) and Bluetooth v4.0 LE Half Mini-Card Module (Factory Option) 2.0M HD PC Video Camera Module (Factory Option) Security Physical Dimensions & Weight Security (Kensington® Type) Lock Slot BIOS Password Trusted Platform Module 1.
