Service manual
Table Of Contents
- Manual
- Preface
- 1: Introduction
- Overview
- System Specifications
- External Locator - Top View with LCD Panel Open
- External Locator - Front & Left Side Views
- External Locator - Right Side & Rear Views
- External Locator - Bottom View
- Mainboard Overview - Top (Key Parts)
- Mainboard Overview - Bottom (Key Parts)
- Mainboard Overview - Top (Connectors)
- Mainboard Overview - Bottom (Connectors)
- 2: Disassembly
- Overview
- Maintenance Tools
- Connections
- Maintenance Precautions
- Disassembly Steps
- Removing the Battery
- Removing the Hard Disk Drive
- Removing the Modem
- Removing the Wireless LAN
- Removing the System Memory (RAM)
- Removing the Optical (CD/DVD) Device
- Removing the Processor
- Removing the Keyboard
- Appendix A: Part Lists
- Appendix B: Schematic Diagrams
- System Block Diagram
- Socket 479 - 1 of 2
- Socket 479 - 2 of 2
- 855PM MCH-1
- 855PM MCH-2
- 855PM MCH-3
- DDRAM
- DDR Termination
- Clock Generator
- ICH4-1 (1 of 3)
- ICH4-2 (2 of 3)
- ICH4-3 (3 of 3)
- USB 2.0
- MDC, BT, CCD, Mini PCI
- HDD, CDROM
- LAN RTL8110S (B)-32
- LPC S I/O, Flash ROM
- Power On Checklist
- Hitachi H8S
- Audio Codec ALC202
- PCMCIA (PCI1620)
- PCMCIA Socket
- TI1394 (TSB43AB21)
- M10 AGP/PCI/Power
- M10 MEM I/F-A
- M10 MEM I/F-B
- M10 VGA Connector
- Panel CON
- VGA DDR DRAM Termination
- Audio Out & Off Board
- BTVCC, +1.5V, +1.8VS
- V_CORE
- +VDD3, +VDD5, +12V, +3V, +5V
- +2.5VS, +1.25VS, +5VS, +3VS
- Charger
- SMSC LPC47N217 LPC I/F
Disassembly
2 - 6 Removing the Hard Disk Drive
2.Disassembly
Removing the Hard Disk Drive
The hard disk drive is mounted in a removable case and can be taken out to accommodate other 2.5" IDE hard disk drives
with a height of 9.5mm (h). Follow your operating system’s installation instructions, and install all necessary drivers and
utilities (as outlined in Chapter 4 of the User’s Manual) when setting up a new hard disk.
Hard Disk Upgrade Process
1. Turn off the computer, and remove the battery (page 2 - 5).
2. Locate the hard disk and HDD bay cover .
3. Remove screws
- and remove the HDD bay cover .
Figure 2
HDD Assembly
Removal
a. Locate the HDD bay cov-
er
b. Remove the 7 screws.
c. Remove the cover.
1
2 8 1
1. HDD Bay Cover
•7 Screws
HDD System Warning
New HDD’s are blank. Be-
fore you begin make sure:
You have backed up any
data you want to keep from
your old HDD.
You have all the CD-ROMs
and FDDs required to in-
stall your operating system
and programs.
If you have access to the
internet, download the lat-
est application and hard-
ware driver updates for the
operating system you plan
to install. Copy these to a
removable medium.
a.
b.
1
43
6
5
7
2
8
1