Service manual
Table Of Contents
- Manual
- Preface
- 1: Introduction
- Overview
- System Specifications
- External Locator - Top View with LCD Panel Open
- External Locator - Front & Left Side Views
- External Locator - Right Side & Rear Views
- External Locator - Bottom View
- Mainboard Overview - Top (Key Parts)
- Mainboard Overview - Bottom (Key Parts)
- Mainboard Overview - Top (Connectors)
- Mainboard Overview - Bottom (Connectors)
- 2: Disassembly
- Overview
- Maintenance Tools
- Connections
- Maintenance Precautions
- Disassembly Steps
- Removing the Battery
- Removing the Hard Disk Drive
- Removing the Modem
- Removing the Wireless LAN
- Removing the System Memory (RAM)
- Removing the Optical (CD/DVD) Device
- Removing the Processor
- Removing the Keyboard
- Appendix A: Part Lists
- Appendix B: Schematic Diagrams
- System Block Diagram
- Socket 479 - 1 of 2
- Socket 479 - 2 of 2
- 855PM MCH-1
- 855PM MCH-2
- 855PM MCH-3
- DDRAM
- DDR Termination
- Clock Generator
- ICH4-1 (1 of 3)
- ICH4-2 (2 of 3)
- ICH4-3 (3 of 3)
- USB 2.0
- MDC, BT, CCD, Mini PCI
- HDD, CDROM
- LAN RTL8110S (B)-32
- LPC S I/O, Flash ROM
- Power On Checklist
- Hitachi H8S
- Audio Codec ALC202
- PCMCIA (PCI1620)
- PCMCIA Socket
- TI1394 (TSB43AB21)
- M10 AGP/PCI/Power
- M10 MEM I/F-A
- M10 MEM I/F-B
- M10 VGA Connector
- Panel CON
- VGA DDR DRAM Termination
- Audio Out & Off Board
- BTVCC, +1.5V, +1.8VS
- V_CORE
- +VDD3, +VDD5, +12V, +3V, +5V
- +2.5VS, +1.25VS, +5VS, +3VS
- Charger
- SMSC LPC47N217 LPC I/F
Disassembly
2 - 2 Overview
2.Disassembly
NOTE: All disassembly procedures assume that the system is turned OFF, and disconnected from any power supply (the
battery is removed too).
Maintenance Tools
The following tools are recommended when working on the notebook PC:
• M3 Philips-head screwdriver
• M2.5 Philips-head screwdriver (magnetized)
• M2 Philips-head screwdriver
• Small flat-head screwdriver
• Pair of needle-nose pliers
• Anti-static wrist-strap
Connections
Connections within the computer are one of four types:
Locking collar sockets for ribbon connectors To release these connectors, use a small flat-head screwdriver to
gently pry the locking collar away from its base. When replac-
ing the connection, make sure the connector is oriented in the
same way. The pin1 side is usually not indicated.
Pressure sockets for multi-wire connectors To release this connector type, grasp it at its head and gently
rock it from side to side as you pull it out. Do not pull on the
wires themselves. When replacing the connection, do not try to
force it. The socket only fits one way.
Pressure sockets for ribbon connectors To release these connectors, use a small pair of needle-nose pli-
ers to gently lift the connector away from its socket. When re-
placing the connection, make sure the connector is oriented in
the same way. The pin1 side is usually not indicated.
Board-to-board or multi-pin sockets To separate the boards, gently rock them from side to side as
you pull them apart. If the connection is very tight, use a small
flat-head screwdriver - use just enough force to start.