V10.1.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. VIII • Only use a power adapter approved for use with this computer.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .................................................................................I FCC Statement ................................................................ III FCC RF Radiation Exposure Statement: ........................ IV Instructions for Care and Operation ............................... VI Power Safety ................................................................ VIII Battery Precautions ......................................................... IX Cleaning ............
Preface Optimizing Audio Recording ......................................2-12 Adding a Printer ...........................................................2-13 USB Printer ..................................................................2-13 Parallel Printer .............................................................2-13 Power Management Overview ........................................................................3-1 The Power Sources ........................................................
Preface Wireless LAN Module ...................................................4-9 3.75G/HSPA Module .....................................................4-9 BIOS Utilities Overview ........................................................................5-1 The Power-On Self Test (POST) ...................................5-2 Failing the POST ...........................................................5-3 Fatal Errors ....................................................................5-3 Non-Fatal Errors ..
Preface PC Camera Driver Installation .......................................7-8 Wireless LAN Module .................................................7-15 802.11b/g/n Driver Installation ....................................7-16 Intel® Wi-Fi Link Series Driver Installation ...............7-16 Connecting to a Wireless Network in Windows 7 .......7-17 3.75G/HSPA Module ...................................................7-21 Mobile Partner .............................................................
Preface Memory ......................................................................... C-2 Video ............................................................................. C-2 BIOS ............................................................................. C-3 Storage .......................................................................... C-3 Audio ............................................................................ C-3 Keyboard, Pointing Device & Buttons .........................
Preface XX
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, 3-in-1 card reader, ExpressCard/34), Touchpad & Mouse, Audio & Printer. • Chapter 3 The computer’s power saving options.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a of interest to you.
Quick Start Guide Not Included Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find that this manual refers to the Windows 7 operating system.
1 Quick Start Guide Model Differences This notebook series includes two different model types that mainly differ as indicated in the table below. Note that your model may appear slightly different from those pictured in this manual. Feature Model A Model B Display Type Supported 15.6” (39.62cm) HD (1366 * 768) / HD+ (1600 * 900) / FHD (1920 * 1080) 16:9 LCD Panel 17.3” (43.94cm) HD+ (1600 * 900) / FHD (1920 * 1080) 16:9 LCD Panel MOFA LCD Back Cover Factory Option N/A 3.
Quick Start Guide System Map: LCD Panel Open - Model A 1 Wireless Device Operation Aboard Aircraft 2 4 5 6 7 8 9 10 4 5 3 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the key combinations to toggle power to the 3.
1 Quick Start Guide Figure 1 - 3 LCD Panel Open Model B 1. 2. 3. 4. 5. 6. 7. 8. 9. System Map: LCD Panel Open - Model B 1 Built-In PC Camera (Optional) LCD Power Button GPU Button LED Indicators Hot Key Buttons Keyboard Built-In Microphone Touchpad & Buttons Wireless Device Operation Aboard Aircraft 2 4 5 6 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Quick Start Guide LED Indicators Icon The LED indicators on the computer display helpful information about the current status of the computer.
1 Quick Start Guide Hot Key Buttons Press the hot key buttons (these also feature as LED indicators) on the computer to toggle the appropriate function on/off. When the WLAN or PC camera module is powered on the appropriate icon will be highlighted.
Quick Start Guide Keyboard The keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See Table 1 - 5, on page 1 - 12 for full function key combination details. Function Keys NumLk & ScrLk Keys Play/Pause Key Numerical Keypad 3.
1 Quick Start Guide Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed. Keys Function Keys Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F5/F6 Fn + Fn + F1 Function Volume Decrease/Increase 3.
Quick Start Guide System Map: Front & Left Views Figure 1 - 5 Front & Left Views 1 2 1. 3 4 5 5 6 7 2. 9 8 3-in-1 Card Reader The card reader allows you to use the most popular digital storage card formats: MMC (MultiMedia Card) / RS MMC SD (Secure Digital) / Mini SD / SDHC / SDXC Compatible MS (Memory Stick) / MS Pro / MS Duo 3. 4. 5. 6. 7. 8. 9. LED Indicators (see Table 1 - 2, on page 1 - 9) External Monitor Port RJ-45 LAN Jack HDMI-Out Port 2 * USB 2.
1 Quick Start Guide Figure 1 - 6 Right & Rear Views 1. 2. 3. 4. 5. 6. 7. 8. 9. Headphone-Out Jack Microphone-In Jack S/PDIF-Out Jack USB 2.
Quick Start Guide Disk Eject Warning Changing DVD Regional Codes Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice. Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.
1 Quick Start Guide Figure 1 - 7 Bottom View Model 1. 2. 3. 4. 5. Battery Component Bay Cover Fan Intake Hard Disk Bay Cover Speakers System Map: Bottom View - Model A 1 Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 11 for full instructions.
Quick Start Guide System Map: Bottom View - Model B Figure 1 - 8 Bottom View Model B 1 3 Battery Information 3 Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 11 for full instructions. 2 3 1. 2. 3. 4. 5.
1 Quick Start Guide 3.75G/HSPA Module USIM Card Installation If you have included an optional 3.75G/HSPA module in your purchase option (Factory Option for Model A Computers Only), follow the instructions below to install the USIM card (which will be provided by your service provider), and then run the Mobile Partner application. See “Mobile Partner” on page 7 - 24 for instructions on installing the program etc. 1. 2.
Quick Start Guide Windows 7 Start Menu & Control Panel Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
1 Quick Start Guide Video Features NVIDIA® Optimus™ Technology NVIDIA® Optimus™ technology is a seamless technology designed to get best performance from the graphics system while allowing longer battery life, without having to manually change settings. When the computer is in Optimus Mode it will automatically switch between the integrated UMA (Unified Memory Architecture) GPU (iGPU) and the discrete GPU (dGPU) when required by the applications in use.
Quick Start Guide To access Display (Control Panel) and Screen Resolution in Windows: 1. 2. 3. 4. 5. 6. Click Start and click Control Panel. Click Display (icon) - In the Appearances and Personalization category. Click Adjust Screen Resolution/Adjust resolution. Alternatively you can right-click the desktop and select Screen resolution. Use the dropbox to select the screen Resolution 1 (Figure 1 - 11). Click Advanced settings 2 (Figure 1 - 11) to bring up the Advanced properties tabs.
1 Quick Start Guide To access the Intel(R) Graphics and Media Control Panel: 1. 2. Click Advanced settings 2 (Figure 1 - 11 on page 1 - 21) in the Display Settings control panel in Windows. Click Graphics Properties (button) 3 (Figure 1 - 12) in the Intel Graphics & Media Control Panel tab. OR 3. Right-click the desktop and select Graphics Properties from the menu. OR 4. Click the icon 4 (Figure 1 - 12) in the taskbar and select Graphics Properties from the menu. OR 5.
Quick Start Guide To access the NVIDIA Control Panel: 1. Right-click the desktop and select NVIDIA Control Panel 5 (Figure 1 - 13). OR 2. Click the icon 6 (Figure 1 - 13) in the taskbar and select Open the NVIDIA Control Panel from the menu.
1 Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 17) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Quick Start Guide MOFA LCD Back Covers - Model A MOFA (Magic of Film Art) technology allows fashionable and unique pictorial designs to be printed on the specially designed changeable LCD back covers.
1 Quick Start Guide 1 - 26
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • Hard Disk Drive Optical (CD/DVD) Device 3-in-1 Card Reader Touchpad and Buttons/Mouse Audio Features Optimizing Audio Recording Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Figure 2 - 1 Hard Disk Location 2 - 2 Hard Disk Drive Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 13).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 15. .
Features & Components 2 Card Reader Cover Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. 3-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “CardReader” on page 4 - 7.
Features & Components Touchpad and Buttons/Mouse The Touchpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The Touchpad buttons function in much the same way as a two-button mouse. Once you have installed the Touchpad driver (see “Touchpad” on page 4 - 7) you can configure the functions by double-clicking the Touchpad driver icon on the taskbar.
Features & Components 2 Show Video You can get a clearer view of the gestures involved by clicking the Show Video option for each gesture item. Select the gesture (Pinch Zoom, Rotating, Three Fingers Down and Three Finger Flick) in the Device Settings > Settings left tree menu and click the Show Video button to see the demonstration video.
Features & Components Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the Touchpad surface and slide both fingers in the direction required (in a straight continuous motion).
Features & Components Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the Touchpad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Features & Components Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon to bring up an audio menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination. Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer).
Features & Components Optimizing Audio Recording 2 Follow these instructions to optimize your audio recording. 1. 2. 3. 4. Figure 2 - 11 Optimizing Audio Recording 2 - 12 Audio Features Double-click the taskbar icon to bring up the Realtek HD Audio Manager. Click the Microphone tab. Click the Noise Suppression button to prevent any background noise or feedback. Click OK to close the Realtek HD Audio Manager.
Features & Components Adding a Printer The most commonly used peripheral is a printer. The following conventions will help you to add a printer; however it is always best to refer to the printer manual for specific instructions and configuration options. USB Printer Most current printers have a USB interface connection. You may use any one of the ports to connect the printer. Install Instructions: 1. 2. 3. 4. 5.
Features & Components 2 2 - 14
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the LCD and hard disk drive) or the whole system.
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. 3 AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack at the rear of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings (Win 7) 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management Power-Saving States 3 You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. It is recommended that you enable a password on wake up in order to protect your data.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Power Status Icon To Resume Color Power Off Off Press the Power Button Sleep Blinking Green Press the Power Button Closing the Lid If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Power Management 3 Taskbar Icon If the taskbar icon does not appear then click the taskbar arrow and select Customize. Energy Star Power Saving This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. If you want to enable Energy Star power saving then follow these instructions: 1. 2. 3. Right-click the taskbar icon (see sidebar). Select Power Conservation Modes.
Power Management Battery Information Follow these simple guidelines to get the best use out of your battery. Low Battery Warning Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure 3 - 1 on page 3 - 4).
Power Management Conserving Battery Power 3 Wireless Hot Keys The computer’s wireless function keys will not function properly if Wireless is turned OFF in the Windows Mobility Center control panel. The wireless indicators may show that the WLAN module is powered on, however if wireless is OFF in the Mobility Center, the module will not be powered on. • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance.
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery” on page 6 - 3.
Power Management Proper handling of the Battery Pack 3 Caution • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 1. 2. 3 Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management 3 How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Windows 7 Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers/Option Drivers (button). 4 Figure 4 - 1 - Drivers Installer Screen 1 1. 2. 3. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below. Click to select the driver you wish to install, (you should note down the drivers as you install them).
Drivers & Utilities Driver Figure 4 - 2 - Drivers Installer Screen 2 Win 7 Chipset Page 4 - 6 Video (VGA) Page 4 - 6 NVIDIA Video (VGA) Page 4 - 6 MEI Driver Page 4 - 6 Modem Page 4 - 6 LAN Page 4 - 6 CardReader Page 4 - 7 Touchpad Page 4 - 7 Hot Key Page 4 - 7 USB 3.0 Page 4 - 7 Audio Page 4 - 7 PC Camera Module Page 7 - 8 Wireless LAN Module Page 7 - 16 3.
Drivers & Utilities Manual Driver Installation Click Browse CD/DVD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder. 4 Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See “Windows Update” on page 4 8 for instructions.
Drivers & Utilities User Account Control New Hardware Found If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as directed. If you see the message “New Hardware Found” during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure.
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). 4 Chipset 1. Click 1.Install Chipset Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. Video (VGA) 1. Click 2.Install VGA Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. NVIDIA Video (VGA) 1. Click 3.Install nVIDIA VGA Driver > Yes. 2. Click Next > Next. 3.
Drivers & Utilities CardReader 1. Click 7.Install Cardreader Driver > Yes. 2. Click Install. 3. Click Finish. Touchpad 1. Click 8.Install Touchpad Driver > Yes. 2. Click Next. 3. Click the button to accept the license agreement and click Next. 4. Click Finish > Restart Now to restart the computer. Hot Key 1. Click 9.Install Hotkey AP > Yes. 2. Click Next > Next. 3. Click Finish > Finish to restart the computer. USB 3.0 1. Click 10.Install USB 3.0 Driver > Yes. 2. Click Next. 3.
Drivers & Utilities Windows Experience Index Windows Update 4 After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). To enable Windows Update make sure you are connected to the internet: 1. 2. 3. 4. 5. 6. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Windows Update (System and Security/ Security).
Drivers & Utilities Optional Drivers Bluetooth Module See the pages indicated for the driver installation procedures for any modules included in your purchase option. Note: The operating system is the default setting for Bluetooth control in Windows 7 and does not require a driver. See “Bluetooth Module” on page 7 - 2 for configuration instructions. PC Camera Module See the introduction in “PC Camera Module” on page 7 - 7, and check the installation procedure.
Drivers & Utilities 4 4 - 10
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors BIOS Settings Warning Incorrect settings can cause your system to malfunction.
BIOS Utilities The Setup Utility The Phoenix SecureCore(tm) Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu Figure 5 - 2 Main Menu 5 System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
BIOS Utilities SATA Port 1/2/3 (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Port 1/2/3. Use the Auto (Type:) setting to have the items configured automatically for you. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
BIOS Utilities Advanced Menu 5 Figure 5 - 3 Advanced Menu Advanced Chipset Control (Advanced Menu) The sub-menu here allows you to enable/disable the JMicron Power Saving (as used by the card reader) control, and to adjust the amount of Total Graphics Memory used by the system.
BIOS Utilities Total Graphics Memory (Advanced Menu > Advanced Chipset Control) Use this menu item to set the amount of system memory to be allocated for use by Intel® Dynamic Video Memory Technology for the graphics device. The default memory size allocated is MaxDVMT (up to 1748MB) and this may be adjusted to 128MB or 256MB (by pressing the spacebar to adjust) if required (see “Dynamic Video Memory Technology” on page B - 5).
BIOS Utilities Legacy OS Boot: (Advanced Menu) Enable this item to support only system boot from the Legacy OS (e.g Windows Vista). If disabled the system will attempt to boot from the EFI (Extensible Firmware Interface) before the Legacy OS. Power on Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up. 5 Battery Low Alarm Beep (Advanced Menu) Use this menu item to enable/disable the battery low alarm beep.
BIOS Utilities Security Menu Security Menu The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Set Supervisor Password (Security Menu) You can set a password for access to the Phoenix SecureCore(tm) Setup Utility. This will not affect access to the computer OS, (only the Phoenix SecureCore(tm) Setup Utility).
BIOS Utilities Password Warning 5 If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. 5 - 12 Security Menu Set User Password (Security Menu) You can set a password for user mode access to the Phoenix SecureCore(tm) Setup Utility.
BIOS Utilities Boot Menu BIOS Screens Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS. BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages. When you turn the computer on it will look for an operating system (e.g. Windows 7) from the devices listed in this menu, and in this priority order.
BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu 5 Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 .
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the discs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium. Upgrading the Hard Disk Drive The hard disk drive can be taken out to accommodate other 2.
Upgrading The Computer 1. 2. 3. Turn off the computer, and turn it over and remove the battery. Locate the hard disk bay cover and remove screws 1 & 2 . Remove the hard disk bay cover 3 .
Upgrading The Computer Hard Disk Screws & Cover 6 4. 5. 6. 7. Slide the hard disk in the direction of arrow 4 . Lift the hard disk out of the bay 5 . Remove the screw(s) 6 - 9 and the adhesive cover 10 . Reverse the process to install a new hard disk drive (do not forget to replace all the screws and covers). The hard disks and covers pictured here may appear slightly different from your model design (these designs are subject to change and upgrade without notice).
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Locate the hard disk bay cover and remove screws 1 & 2 . Remove the hard disk bay cover 3 . Slide the hard disk in the direction of arrow 4 and lift the hard disk out of the bay.
Upgrading The Computer 5. 6. 7. Figure 6 - 5 6 Remove the screw at point 5 , and use a screwdriver to carefully push out the optical device at point 6 . Reverse the process to install the new device. Replace the hard disk bay cover.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDRIII (DDR3) type memory modules (see “Memory” on page C - 2 for details of supported module types). 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Locate the component bay cover and remove screws 1 - 4 . Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover.
Upgrading The Computer 5. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 7 & 8 ) in Figure 6 - 7. Figure 6 - 7 RAM Module Release Latches 7 8 6 Contact Warning Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. Figure 6 - 8 6. The RAM module will 9 pop-up, and you can remove it.
Upgrading The Computer 7. 8. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. 9. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure. 10. Press the module in and down towards the mainboard until the slot levers click into place to secure the module. 11.
Upgrading The Computer Rubber Screw Covers 6 After removing the rubber screw covers, place them on a clean dry surface (or attach them to the front cover itself) in order to prevent loss of adhesive. Changing the Optional LCD Back Covers If your purchase option includes the specially designed changeable LCD back cover option, then follow the instructions below to change the covers (note these covers are not applicable to all models in this series - consult your service center for details). 1. 2.
Upgrading The Computer 3. Carefully slide the cover forward in the direction of the arrows 5 & 6 as illustrated below. 5 6 Figure 6 - 11 Slide the Cover Forward 6 4. Remove the LCD back cover 7 .
Upgrading The Computer 5. Align the replacement cover with the top of the LCD 8 as illustrated below (and as marked on the cover). 8 10 6 10 9 Figure 6 - 13 9 Replacing the LCD Back Cover 10 6. 7. 8. Slide the cover forward slightly until it clicks firmly into place 9 . Run your hands around the sides and front of the cover 10 to make sure it is firmly aligned in place (carefully press down to make sure the fit is secure). Replace the screws and rubber covers (see Figure 6 - 10 on page 6 - 12).
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • • • • • Bluetooth Module PC Camera Module Wireless LAN Module 3.75G/HSPA Module Fingerprint Reader Module Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Modules & Options Wireless Device Operation Aboard Aircraft Bluetooth Module If your purchase option includes a Bluetooth module, then the operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows 7, and therefore does not require a driver. Use the Fn + F12 key combination to toggle power to the Bluetooth module. The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Modules & Options Bluetooth Configuration in Windows 7 Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). Add a Device To Turn the Bluetooth Module On 1. 2. 3. Press the Fn + F12 key combination to power on the Bluetooth module. A Bluetooth icon will appear in the taskbar.
Modules & Options To Add a Bluetooth Device 1. 2. Access the Bluetooth Devices control panel and click Add a device. Double-click the device you want to pair with the computer. 3. On first connection the computer will provide you with a pairing code to be entered onto the device. Pairing Options 7 If a device has been previously connected then the pairing option menu will appear when you attempt subsequent connections.
Modules & Options 4. Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing. Figure 7 - 3 Pairing Codes Pairing Code Example The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection procedure, and may require you to confirm a pairing code is correct on both devices. Follow the onscreen instructions to complete the pairing. 5. 6. 7.
Modules & Options To Change Settings for the Bluetooth Device Bluetooth Help 7 To get help on Bluetooth configuration and settings, select Help and Support from the Start menu. Type Bluetooth in the Search Help box, and select an item from the returned search results to get more information. 1. 2. • • Click the taskbar icon and select Show Bluetooth Devices.
Modules & Options PC Camera Module Before installing the PC Camera driver, make sure that the optional PC Camera is on. Use the Fn + F10 key combination (see “Function/Hot Key Indicators” on page 1 - 12) or hot key button to toggle power to the PC Camera module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. There are a number of different camera modules available with this computer model series. You will have the appropriate application installed for your camera.
Modules & Options PC Camera Screen Refresh 7 The PC Camera module supports a frame rate of 12 fps. If you find that the screen refresh rate is subject to lag or stuttering, then reduce the window size, or adjust the Output Size and/or Color Space Compression. To reduce Output Size and/or Color Space Compression run the camera application, click Options and select Video Capture Pin. Adjust the settings from the appropriate pull-down menu. PC Camera Driver Installation 1.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone (Realtek High Definition Audio) and make sure the item is not disabled. 5. Double-click Microphone (or select Properties from the right-click menu). 6.
Modules & Options Figure 7 - 6 Audio Setup for PC Camera Right-click 7 7 - 10 PC Camera Module
Modules & Options Camera Application The camera application is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format. 1. 2. 3. Run the camera application from the desktop shortcut (it is recommended that you set the capture file before the capture process - see Set Capture File below). Go to the Capture menu heading (if you wish to capture audio check “PC Camera Audio Setup” on page 7 - 9) and select Start Capture.
Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules & Options Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the camera application from the desktop shortcut. Go to Options and scroll down to select Video Capture Filter.... Click either 50Hz or 60Hz under Anti Flicker/Frequency/Powerline Frequency.
Modules & Options Zoom (if supported by application) The WebCam program allows you to zoom the camera in and out (note the zoom function is not available in all camera model applications). 1. 2. Run the camera application from the desktop shortcut. Go to Zoom and select Zoom Out/Zoom In. Figure 7 - 8 Zoom/Setting 7 Snapshot Folder The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture.
Modules & Options Wireless LAN Module If you have included an Intel® Wi-Fi Link 6200/6300 Series or 3rd Party 802.11b/ g/n WLAN module in your purchase option, make sure that the Wireless LAN module is on before installing the driver. Use the Fn + F11 key combination (see “Function/Hot Key Indicators” on page 1 - 12) or hot key button to toggle power to the Wireless LAN module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3.
Modules & Options 802.11b/g/n Driver Installation If you see the message “Found New Hardware” click Cancel to close the window. 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 2.Install WLAN Driver > Yes. 4. Choose the language you prefer and click Next. 5. Click Next > Install. 6. Click Finish to restart the computer.
Modules & Options Connecting to a Wireless Network in Windows 7 Make sure the Wireless LAN module is turned on. 1. Click the taskbar wireless icon , and then double-click an access point to connect to or click to Open Network and Sharing Center if you do not see a network you want to connect to in the taskbar menu (a list of options will appear allowing setting changes, and creating a new network).
Modules & Options 2. 3. 4. You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click “View or change settings in Network and Sharing Center” to access further options for the connection.
Modules & Options 5. 6. Click the taskbar icon to see any currently connected networks. To disconnect from the wireless network you can click the taskbar wireless icon click the active connection and then click Disconnect (button). , Security Enabled Networks You should try to make sure that any network you are connecting to is a secure network. Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Windows Mobility Center Wireless Hot Keys The computer’s wireless function keys will not function properly if Wireless is turned OFF in the Windows Mobility Center control panel. The 7 wireless indicators may show that the WLAN module is powered on, however if wireless is OFF in the Mobility Center, the module will not be powered on.
Modules & Options 3.75G/HSPA Module If you have included an optional (for Model A Only) 3.75G/HSPA (High Speed Packet Access) module (see “Communication” on page C - 3 for specification details) in your purchase option, you will have the appropriate application provided for your module. Follow the instructions on page 7 - 22 to install the USIM card (which will be provided by your service provider), and then install the application. Important Notice - 3.75G/HSPA & Bluetooth/Wireless LAN Modules 3.
Modules & Options Power Safety Warning 7 Before you undertake any installation procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. 3.75G/HSPA Module USIM Card Installation Follow the instructions below to install the USIM card (which will be provided by your service provider). 1. 2. 3. 4. 5.
Modules & Options Before installing the application, make sure that the 3.75G/HSPA module is ON (installing the driver with the module off will not allow the software to detect the module hardware correctly). Use the Fn + key combination (see Table 1 - 5, on page 1 - 12) to toggle power to the 3.75G/HSPA module. When the 3.75G/HSPA module is powered on, the indicator will briefly be displayed. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3.
Modules & Options Mobile Partner Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + key combination to toggle power to the 3.75G/HSPA module, and check the indicator to see if the module is powered on or not (see Table 1 - 5, on page 1 - 12/ Table 1 - 3, on page 1 - 9). With the 3.
Modules & Options Mobile Partner Application You will need to contact your service provider to obtain the exact details of how exactly to configure the settings on this page. Profile Management 1. 2. 3. 4. 5. Power on the 3.75G/HSPA module using the Fn + key combination. Access the Mobile Partner application from the Start menu (Start > Programs/ All Programs > Mobile Partner), or by double-clicking the Mobile Partner icon on the desktop .
Modules & Options Connecting to the Service Provider 1. 2. 3. 4. Power on the 3.75G/HSPA module using the Fn + key combination. Access the Mobile Partner application from the Start menu (Start > Programs/ All Programs > Mobile Partner), or by double-clicking the Mobile Partner icon on the desktop . The software will run and you can select the Profile Name from the menu. Click Connect to begin the connection process. 5. The Mobile Partner application will then display the connection information.
Modules & Options 6. When the connection is successful you can move the cursor over the network icon in the taskbar to display the connection information. Figure 7 - 17 Connected Taskbar Notification 7. 8. 9. You can then access the internet, download e-mail etc. as per any internet connection. While you are connected the indicators in the Mobile Partner window will display uploading and downloading icons and a network icon in the taskbar . To disconnect click the Disconnect and select Disconnect.
Modules & Options 11. The module will still be on, and you will need to press the Fn + key combination to turn it off. 12. If you click the Mobile Partner close icon a message will be displayed asking you to click OK to confirm the program exit and to terminate the connection. Figure 7 - 19 Exit Prompt 7 13. Exiting the program terminates the connection, but DOES NOT turn off the 3.
Modules & Options Text Messaging Service In addition to standard internet services you may also send and receive SMS text messages using the Mobile Partner program, if your service supports SMS. Reading SMS Messages 1. 2. 3. 4. An icon will blink at the bottom of the Mobile Partner interface to notify you of any new messages received. Click the Text icon in the Mobile Partner Interface. Select the Local > Inbox or SIM/USIM Card folder and select any message to read it.
Modules & Options Password Warning If you set passwords for any of the security modules, NEVER forget your password. 7 The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. Fingerprint Reader Module The optional (for Model A Only) fingerprint reader Protector Suite Software provides a high level of security for your computer.
Modules & Options Fingerprint Reader Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 4.Install Fingerprint Driver > Yes. 4. Click Next > Next > Next. 5. Click Finish > Yes to restart the computer. Help & Manual Right-click the taskbar icon to bring up the menu to select Help.
Modules & Options User Enrollment 1. Fingerprint Enrollment 2. Note that it is strongly recommended that you enroll more than one finger in case of injury etc. 3. 4. 5. Click Start > Programs/All Programs > Protector Suite > Control Center, or double click the taskbar icon (click Initialize). On the first run of the program you will be asked to click the Accept button to accept the license.
Modules & Options 6. Click the button above any of the fingers to begin the enrollment process for that finger. 7. Swipe the finger until the progress bar reaches 100% to enroll that finger. 8. Close the Protector Suite 2009 window. 9. Right-click the taskbar icon and select Start Control Center (and then swipe a finger) to allow you to Edit Fingerprints, register Applications, edit Settings and access the Help menu etc. You can also run the Control Center etc.
Modules & Options Fingerprint Control Center Features Help For more information on these and other features simply access “Help” in the Fingerprint Control Center and select the item from the menu on the left. 7 Application Launcher The Application Launcher allows you to register applications to be launched when assigned to a particular finger. Simply copy the application icon on to one of the registered fingers and ten click OK to close the application window.
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 9) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator blinking orange. , is Low Battery. Plug in the DC power source.
Troubleshooting Problem The computer feels too hot. Possible Cause - Solution Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 16). Make sure you’re using the correct adapter.
Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Possible Cause - Solution Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work. 8 The system freezes or the screen goes dark. The system’s power saving features have timed-out.
Troubleshooting Problem Possible Cause - Solution The Wireless LAN indicators show that the WLAN module is powered on, however the module does not connect. The WLAN module is turned off in the Windows Mobility Center. The computer’s wireless function keys will not function properly if Wireless is turned OFF in the Windows Mobility Center control panel. Make sure that Wireless is ON in the Mobility Center to ensure proper function key behavior (see “Wireless Hot Keys” on page 3 - 12).
Troubleshooting Problem Possible Cause - Solution I am sliding my finger up and down on the right side of the Touchpad to scroll a Window and the Touchpad does not respond. There are different Touchpad versions available on this computer, and this version requires tapping/holding to scroll. Either tap repeatedly, or hold the finger down, at the top or bottom right of the Touchpad (depending on the scrolling direction required) to scroll the window.
Troubleshooting Bluetooth Connection Problems If you are experiencing problems connecting to some Bluetooth devices (in particular certain mobile phones and headsets) it maybe necessary to download and install the Windows Mobile Device Center software (for Windows Vista and Windows 7). Go to the Microsoft website and search for the Microsoft Windows Device Center Driver for Windows Vista (64-bit or 32-bit) and Windows 7 (64-bit or 32-bit), and then download the driver. 1. 2. 3. 4. 5.
Troubleshooting 6. 7. 8. 8 Right-click Bluetooth Peripheral Device and click on Update Driver Software. Click Browse my computer for driver software. Click Let Me pick from a list of device drivers on my computer. Figure 8 - 2 - Browse my computer.../Let me pick from... 9. Select Bluetooth Radios from the list.
Troubleshooting 10. A list of drivers will appear with Manufacturer on one side and Model in the other. 11. Choose Microsoft Corporation (make sure you choose the full name Microsoft Corporation and do not choose Microsoft - Note that you must have installed the Microsoft Windows Device Center Driver for Microsoft Corporation to appear in the list). 12. Select Windows Mobile-based device support from the Model list. 8 Make sure you select Microsoft Corporation Figure 8 - 4 - Select Device Driver 13.
Troubleshooting 15. The Device Manager should now display the Windows Mobile-based device support under Bluetooth Radios. 16. You will need to repeat the process for any other Bluetooth Peripheral Devices listed under Other Devices.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
Interface (Ports & Jacks) Item Microphone-In Jack RJ-11 Phone Jack RJ-45 LAN Jack Description Plug an external microphone in to this jack to record on your computer. This port connects to the built-in modem if included in your purchase configuration (the modem and modem port are a factory option). You may plug the telephone line directly into this RJ-11 telephone connection. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. This port supports LAN (Network) functions.
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Video Driver Controls Appendix B: Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 20. Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). Video Card Options Note that card types, specifications and drivers are subject to continual updates and changes.
Video Driver Controls NVIDIA® Optimus™ Technology iGPU or dGPU Most notebook computers come with either a discrete or integrated graphics solution. Note the NVIDIA control panel refers to Highperformance NVIDIA processor (which is the discrete GPU) and Integrated graphics (which is the integrated GPU). Discrete graphics solutions feature a dedicated Graphics Processing Unit (GPU) which are capable of playing games, watching HD video or running GPU-based applications.
Video Driver Controls How Optimus Technology works When the system is powered up and is displaying just the desktop, the dGPU will be powered off. In this case the system is running in the same way as a system without a discrete graphics solution. However when an application that requires use of the dGPU is run (e.g, a game or HD Video), the dGPu is powered on and takes over the processing duties. If the program is closed, then the dGPU will be powered back down again until required.
Video Driver Controls GPU Button This computer also features a button that allows the user to switch between Optimus Mode and UMA Mode (Unified Memory Architecture). UMA Mode will use only the integrated GPU; Optimus Mode will allow the system to automatically determine whether the dGPU or iGPU is used. Thus the user can completely control how the graphics system operates. Press the GPU button, and the button color will indicate the current mode.
Video Driver Controls Dynamic Video Memory Technology Intel® DVMT automatically and dynamically allocates as much (up to 1748MB) system memory (RAM) as needed to the integrated video system (the video driver must be installed). DVMT returns whatever memory is no longer needed to the operating system. You can configure the amount of memory to be used by DVMT in the BIOS (see “Total Graphics Memory (Advanced Menu > Advanced Chipset Control)” on page 5 - 9).
Video Driver Controls Intel® Graphics & Media Control Panel Advanced video configuration options are provided by the Intel® Graphics and Media Control Panel. To access the control panel: 1. 2. Click Advanced settings in the Screen Resolution control panel in Windows. Click the Intel(R)... tab and click Graphics Properties (button). OR 3. Right-click the desktop and select Graphics Properties from the menu. OR 4. Double-click the Intel(R) G&M control panel in Windows.
Video Driver Controls You may make changes to any of the graphics properties by clicking the appropriate menu tab on the left of the menu and adjusting the settings on the right. Options & Support Click Options & Support and select an item from the sub-menu to bring up the help and support topics. You will need to be connected to the Internet to access the key resource links. Multiple Display At least one other display must be attached in order to view multiple display selection options.
Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: • Notebook Only • External Display Only • Notebook + External Display Display Devices & Options Besides the built-in LCD you can also use an external monitor/flat panel display/TV connected to the external monitor port or to the HDMI-Out port (High-Definition Multimedia Interface) as your display device. The table below outlines the display options.
Video Driver Controls Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the external monitor port or HDMI-Out port on the left of the computer. To Clone Displays: 1. 2. 3. 4. 5. Attach your display to the external monitor port or HDMI-Out port, and turn it on. Go to the Intel(R) G&M control panel and click Display > Multiple Displays. Click Operating Mode and select Clone Displays from the menu. Click Apply, and OK to confirm the settings change.
Video Driver Controls To Enable Extended Desktop: Display Settings Extended Desktop 1. 2. 3. 4. Attach your display to the external monitor port or HDMI-Out port, and turn it on. Go to the Intel(R) G&M control panel and click Display > Multiple Displays. Click Operating Mode and select Extended Desktop from the menu. Click Apply, and OK to confirm the settings change. You can have different Colors, Screen Area and Monitor Refresh Rates for each display device provided your monitor can support them.
Video Driver Controls Configuring an External Display in Windows 7 You can also use the Screen Resolution control panel in Windows 7 to configure an external display. 1. 2. 3. 4. Attach your display to the external monitor port or HDMI-Out port, and turn it on. Go to the Screen resolution control panel (see “Video Features - Win 7” on page 1 - 16). Click the Detect button. The computer will then detect any attached displays.
Video Driver Controls 5. You can configure the displays from the Multiple Displays menu. Figure B - 6 Screen Resolution Multiple Display Options (Win 7) B • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) • Extend these displays - Treats both connected displays as separate devices • Show desktop only on 1/2 - Only one of your displays is used.
Video Driver Controls Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configuration and modes (this is particularly useful when attaching a projector) in Windows 7. 1. 2. 3. 4. Attach your display to the external monitor port or HDMI-Out port, and turn it on. + P key combination. Press the An on-screen menu will pop up.
Video Driver Controls HDMI Audio Configuration As HDMI (High-Definition Multimedia Interface) carries both audio and video signals you can configure the audio output as per the instructions below. Windows Audio Setup for HDMI 1. 2. 3. 4. 5. Connect a device with HDMI support to the HDMI-Out port. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Playback (tab), and right-click the attached HDMI supported display device.
Video Driver Controls 7. To play audio sources through your external display’s (TV or LCD) speakers you will need to go to the audio configuration control panel on the display and configure the audio input accordingly (see your display device manual). Other Applications HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device. HDMI Video Configuration 1. 2. 3. 4.
Video Driver Controls NVIDIA Control Panel To access the GeForce..... control panel from the desktop; rightclick the desktop, then click NVIDIA Control Panel. NVIDIA Control Panel More advanced video configuration options are provided in the NVIDIA Control Panel tab. 1. 2. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click NVIDIA Control Panel (click "Classic View" from the left of the menu if you are in Control Panel Home). B Figure B - 9 NVIDIA GeForce.
Video Driver Controls The NVIDIA Control Panel provides additional video configuration controls and tools which allow quick access to features such as image settings, 3D Settings and Video & TV configuration. Navigating the Control Panel Navigate through the control panels in much the same way as you would a web page. Click on the sub-heading tasks in the left menu (and on the highlighted links) for information. Use the buttons on the top left to go back, forward etc.
Video Driver Controls Optimus™ Customization Options One of the most important aspects of Nvidia® Optimus™ technology is that it will switch between the integrated GPU and discrete GPU seemlessly and automatically, and does not require any input from the user. However customization options are offered for users who prefer to set their own parameters for GPU usage.
Video Driver Controls 3. 4. 5. 6. 7. Close the NVIDIA Control Panel. Make sure the computer is in Optimus Mode (use the GPU Button to switch modes). Right-click the icon of the application you want to run. Select Run with graphics processor from the context menu. Select either High-performance NVIDIA processor (dGPU) or Integrated graphics (iGPU) to run the program with the selected GPU.
Video Driver Controls Global Settings Global settings allows you to set the preferred graphics processor for overall use. Ideally this would be the iGPU for battery life, but this can also be set to the dGPU if preferred. 1. 2. 3. 4. Run the NVIDIA Control Panel (see page B - 16). Click Manage 3D Settings (3D Settings) and select Global Settings (tab). Select either Integrated graphics (iGPU) or High performance NVIDIA Processor (dGPU) from the drop-down menu.
Video Driver Controls Program Settings Program settings allows you to make specific adjustments for installed applications. 1. 2. 3. 4. 5. Run the NVIDIA Control Panel (see page B - 16). Click Manage 3D Settings (3D Settings) and select Program Settings (tab). Select a program to customize from the drop-down menu, or click Add to add any program that does not appear in the menu. Select the preferred graphics processor for the program from the drop-down menu.
Video Driver Controls TV Settings When the TV is enabled as a display device, click the sub-menus under Video & Television to adjust the video color or image settings.
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.
Specifications Processor Processor (Cont’d) Memory Intel® Core™ i7 Mobile Processor: 620M (2.66GHz) 32nm (32 Nanometer) Process Technology, 4MB L3 Cache & 1066MHz FSB - TDP 35W rPGA988A Socket P Package =============================== Intel® Core™ i3 Mobile Processor: 350M (2.
Specifications BIOS Interface Slots One 32Mb SPI Flash ROM Phoenix™ BIOS Four USB 2.0 Ports OR Three USB 2.0 Ports and One (Factory Option) USB 3.0 Port Two Mini-Card Slots with PCIe (Slot 1) & USB (Slot 2) interfaces: Slot 1 for WLAN Module Slot 2 for 3.75G Module (Factory Option for Model A Computers) Storage One Changeable 12.7mm(h) Super Multi/ Blu-ray Combo Optical Device Drive with SATA Interface (Factory Option) One Changeable 2.5" / 9.
Specifications Communication (Cont’d) Power Environmental Spec Bluetooth v2.1 + EDR (Enhanced Data Rate) Module (Factory Option) Full Range AC/DC Adapter AC input 100 - 240V, 50 - 60Hz, DC Output 19V, 4.74A (90 Watts) Removable 6 Cell Smart Lithium Ion Battery Pack 48.84WH Removable 6 Cell Smart Lithium Ion Battery Pack 62.16WH (Factory Option) Temperature Operating: Non-Operating: Relative Humidity Operating: Non-Operating: 1.3M Pixel PC Camera Module with USB interface UMTS/HSPDA-based 3.
