V09.1.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place it on an unstable surface. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. • The power adapter may have either a 2-prong or a 3-prong grounded plug.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface XIV
Preface Contents Notice .................................................................................I FCC Statement ..................................................................II FCC RF Radiation Exposure Statement: ........................ III EuP Off Mode Power Consumption Statement: ............. III Instructions for Care and Operation ................................ V Power Safety ..................................................................VII Battery Precautions .....................
Preface GameMate Media Player (HDMI-In) ..........................2-10 HDMI Audio Configuration ........................................2-13 Audio Setup for LCD Monitors/ TVs with HDMI Input .................................................2-14 Audio Features .............................................................2-16 Suppressing Audio Background Noise ........................2-17 Setup for Audio Recording ..........................................2-19 Setup for 5.1 Surround Sound ....................
Preface Audio .............................................................................4-5 LAN ...............................................................................4-5 TouchPad .......................................................................4-6 Card Reader/ExpressCard ..............................................4-6 GameKey Utility ............................................................4-6 Hot Key ..........................................................................
Preface Modules Overview ........................................................................7-1 Setting Up SATA RAID Mode ......................................7-2 Intel® Matrix Storage Manager .....................................7-2 SATA RAID Setup Procedure (BIOS) ..........................7-4 RAID Setup (Intel Matrix) .............................................7-5 Intel® Matrix Driver Installation ...................................7-7 Intel® Matrix Storage Manager ..............................
Preface HDMI-IN Port .............................................................. A-3 Headphone-Out Jack ..................................................... A-3 Line-In Jack .................................................................. A-3 Microphone-In Jack ...................................................... A-4 Mini-IEEE 1394 Port .................................................... A-4 RJ-45 LAN Jack ........................................................... A-4 S/PDIF-Out Jack .............
Preface XX
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, 7-in-1 card reader, ExpressCard/34), Game Keys, HDMI Ports, TouchPad & Mouse, Audio Features & Printer.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you. Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide Not Included Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module.
1 Quick Start Guide TV Tuner Module Support Note that the TV Tuner module (factory) option is supported by the Windows Media Center software. Windows Media Center is not included in Starter or Home Basic versions of Windows 7. 1 - 4 Overview System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 7 operating system is supported.
Quick Start Guide System Startup 1. Remove all packing materials, and place the computer on a stable surface. 2. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. 3. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter. 4.
1 Quick Start Guide Figure 1 - 2 LCD Panel Open & Top View 1. Optional Built-In PC Camera 2. LCD 3. LED Status Indicators 4. Touch Sensor Instant Keys 5. 8 * Gaming Keys 6. Keyboard 7. TouchPad and Buttons 8. Fingerprint Reader Module (optional) 9. LED Power Indicators 10. LCD Panel Color LED See Appendix A for a more detailed description of the ports & jacks etc.
Quick Start Guide LED Indicators Game Keys The two sets of LED indicators (LED Status Indicators and LED Power Indicators) display helpful information about the current status of the computer. The eight Game Keys on the left of the computer allow macros to be configured for common keystrokes used in applications, as long as the driver is installed.
1 Quick Start Guide Touch Sensor Instant Keys Press the Touch Sensor Instant Keys on the computer to toggle the appropriate function on/off. When a module is powered on the appropriate icon will be highlighted.
Quick Start Guide Keyboard The keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See Table 1 - 3, on page 1 - 10 for full function key combination details. Function Keys NumLk & ScrLk Keys Play/Pause Key Numerical Keypad Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically.
1 Quick Start Guide Function Keys & Visual Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators (see the table below) are available when the Hot Key driver is installed (see “Hot Key” on page 4 - 6). After installing the driver an icon will appear in the taskbar.
Quick Start Guide System Map: Front & Rear Views 1 1 4 2 2 3 Figure 1 - 5 Front View 2 5 2 1 1 1. Color LEDs 2. Speakers 3. LED Power Indicators 4. Consumer Infrared Transceiver (enabled with optional TV Tuner only) 5. DC-In Jack TV Tuner Module Support Note that the TV Tuner module (factory) option is supported by the Windows Media Center software. Windows Media Center is not included in Starter or Home Basic versions of Windows 7.
1 Quick Start Guide Figure 1 - 6 Right View 1. 2. 3. 4. 5. 6. 7. 8. 9. Headphone-In Jack Microphone-In Jack Line-In Jack S/PDIF-Out Jack Cable (CATV) Antenna Jack* Combined eSATA/ USB Port USB 2.0 Port Security Lock Slot Power Button System Map: Right View 6 1 2 3 4 5 7 9 8 TV Tuner Module Support Note that the TV Tuner module (factory) option is supported by the Windows Media Center software. Windows Media Center is not included in Starter or Home Basic versions of Windows 7.
Quick Start Guide System Map: Left View 1 2 3 Figure 1 - 7 Left View 6 5 4 7 9 1. 2. 3. 4. 5. 6. 7. 8. 9. 8 Mini-IEEE 1394 Port The Mini-IEEE 1394 port only supports SELF POWERED IEEE 1394 devices.
1 Quick Start Guide Disk Eject Warning Changing DVD Regional Codes Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice. Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.
Quick Start Guide System Map: Bottom View Figure 1 - 8 Bottom View 1. Sub Woofer 2. Fan Outlet/Intake 3. Component Bay Cover 4. Battery (Secondary HDD Bay - HDD3) 5. Primary HDD Bay (HDD1 & 2) 1 3 2 4 2 2 5 See Appendix A for a more detailed description of the ports & jacks etc. Overheating Battery Information Always completely discharge, then fully charge, a new battery before using it.
1 Quick Start Guide Windows 7 Start Menu & Control Panel Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
Quick Start Guide Video Features You can configure display options, from the Display Settings control panel in Windows as long as the appropriate video driver is installed. For more detailed video information see “NVIDIA Video Driver Controls” on page B - 1. To access Display (Control Panel) and Screen Resolution in Windows: 1. 2. 3. Click Start and click Control Panel. Click Display (icon) - In the Appearances and Personalization category. Click Adjust Screen Resolution/Adjust resolution. OR 4. 5. 6.
1 Quick Start Guide Screen Resolution Video Options Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported.
Quick Start Guide NVIDIA Control Panel 5 4 3 Figure 1 - 11 - NVIDIA Control Panel Video Features 1 - 19 1
1 Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 16) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Storage Devices, Mouse, Audio & Printer Chapter 2: Storage Devices, Mouse, Audio & Printer Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • • • Hard Disk Drive Optical Device 7-in-1 Card Reader ExpressCard Slot Game Keys HDMI Ports Audio Features TouchPad and Buttons/Mouse Adding a Printer Overview 2 - 1 2
Storage Devices, Mouse, Audio & Printer 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive The hard disk drive(s) is(are) used to store your data in the computer. The hard disk(s) can be taken out to accommodate other 2.
Storage Devices, Mouse, Audio & Printer Optical Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see “Storage” on page C - 2). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 12).
Storage Devices, Mouse, Audio & Printer 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Disk Eject Warning Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.
Storage Devices, Mouse, Audio & Printer DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 14.
Storage Devices, Mouse, Audio & Printer 2 Card Reader Cover Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Storage Devices, Mouse, Audio & Printer ExpressCard Slot The computer is equipped with an ExpressCard/34 slot that reads Express Card/34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards).Make sure you install the ExpressCard driver (see “Card Reader/ExpressCard” on page 4 - 6). 1 Inserting and Removing ExpressCards • Align the ExpressCard with the slot and push it in until it locks into place (as pictured in the generic figure below).
Storage Devices, Mouse, Audio & Printer Game Keys 2 The eight game hot keys on the left of the computer allow macros to be configured for common keystrokes used in applications (the keys can assigned macros for any program, not only games). To configure the keys follow the instructions below (make sure you have installed the GameKey Utility driver - see “GameKey Utility” on page 4 - 6). 1. 2. 3.
Storage Devices, Mouse, Audio & Printer HDMI Ports 2 This computer features both HDMI (High-Definition Multimedia Interface) input and output ports. HDMI is a compact audio/video interface for transmitting uncompressed digital data. • The HDMI-Out port allows you to display and hear video/audio sources from your computer to digital TVs, displays or audio systems that support an HDMI input.
Storage Devices, Mouse, Audio & Printer GameMate Media Player (HDMI-In) 2 The GameMate Media Player allows you to play content from digital sources through the HDMI-In port. 1. 2. 3. 4. Figure 2 - 6 GameMate Player 2 - 10 HDMI Ports Connect your digital source to the HDMI-In port using an HDMI cable. Access the GameMate Media Player from the desktop shortcut or from GameMate folder in Program Files.
Storage Devices, Mouse, Audio & Printer Double-click the GameMate screen to toggle through different screen size options. You can also right-click the screen to access the configuration menu to adjust any of the following settings: 2 RENDERED QUALITY Select High, Medium or Low quality from this menu item. STANDARD Select NTSC or PAL standard from this item. FORMAT Select the screen format here (only supported resolutions will be shown).
Storage Devices, Mouse, Audio & Printer ASPECT The Aspect item allows you to select standard or wide screen aspect ratios. 2 SNAPSHOT Click either the BMP or JPG items to take a screen shot of the current GameMate screen (the file will be placed in the Pictures library folder in Windows). TOPSHOT If enabled then the GameMate screen will remain on top of other windows.
Storage Devices, Mouse, Audio & Printer HDMI Audio Configuration 2 As HDMI (High-Definition Multimedia Interface) carries both audio and video signals you can configure the audio output as per the instructions below. Audio Setup for HDMI 1. 2. 3. 4. 5. 6. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Playback (tab), and click to select Realtek Digital Output. Click Set Default (button).
Storage Devices, Mouse, Audio & Printer Audio Setup for LCD Monitors/TVs with HDMI Input 2 Some LCD monitors/TVs support HDMI input, but DO NOT have built-in digital audio decoders. Where this is the case, when playing DVDs in Windows Media Player/CyberLink Power DVD, a background noise can occur. If this situation does arise then please follow the instructions below. 1. 2. 3. 4. 5. 6.
Storage Devices, Mouse, Audio & Printer HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device. • If you disconnect the HDMI cable the default audio playback device will not revert to speakers until the computer is restarted (if you do not wish to restart the computer then go to the Sound control panel and select Speakers as the default audio playback device). HDMI Video Configuration 1. 2. 3. 4.
Storage Devices, Mouse, Audio & Printer 2 Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer). Click the volume icon in the taskbar to check the setting. Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon to bring up an audio menu).
Storage Devices, Mouse, Audio & Printer Suppressing Audio Background Noise 2 A background noise may occur when audio power management is enabled, and the system resumes from power saving. To solve this problem you can disable Realtek HD Audio Manager Power Management. 1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel) and make sure you are in Classic View. Click Realtek HD Audio Manager (or right-click the taskbar icon and select Sound Manager).
Storage Devices, Mouse, Audio & Printer 4. 2 5. Make sure that Power Management is disabled (when disabled the icon will be black ; when enabled the icon will be blue ). Click OK to save the setting and close the control panel. The black icon indicates that Power Management is disabled.
Storage Devices, Mouse, Audio & Printer Setup for Audio Recording To record audio sources on your computer at optimum quality follow the instructions below: 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel) and make sure you are in Classic View. Click Realtek HD Audio Manager (or right-click the taskbar icon and select Sound Manager).
Storage Devices, Mouse, Audio & Printer Setup for 5.1 Surround Sound 2 To setup your system for 5.1 surround sound you will need to connect the audio cables to the Line-In and Microphone-In jacks. 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel) and make sure you are in Classic View. Click Realtek HD Audio Manager (or right-click the taskbar icon and select Sound Manager). Click Speakers (tab) and click Speaker Configuration (tab). Select 5.
Storage Devices, Mouse, Audio & Printer 5. 6. Plug the front speaker cables into the Headphone-Out Jack. Plug in the other cables (you may require an adapter to connect each cable to the appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers as follows: 2 • Line-In Jack = Rear Speaker Out • Microphone-In Jack = Center/Subwoofer Speaker Out 7. 8. 9. As you plug in each cable a dialog box will pop up (see “Auto Popup Dialog” on page 2 - 20).
Storage Devices, Mouse, Audio & Printer Sound Effects Equalizer 2 Press the Sound Effects Equalizer Mode Toggle button to toggle through some of the equalizer options (an on-screen icon will appear to show the selected mode). A more comprehensive list of options is available from the Equalizer dropdown list. 1. 2. 3. 4.
Storage Devices, Mouse, Audio & Printer Dolby Settings 2 You can adjust the Dolby settings from the Dolby tab in Speakers Properties. 1. 2. 3. 4. 5. 6. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Playback (tab). Double-click Speakers (or select Properties from the right-click menu). Click Dolby (tab) Adjust the settings to your preferences and click OK.
Storage Devices, Mouse, Audio & Printer 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Storage Devices, Mouse, Audio & Printer Gestures and Device Settings The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the TouchPad to perform specific actions to manipulate documents, objects and applications. You can configure the settings from the Device Settings tab in Mouse Properties: 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Mouse (Hardware and Sound).
Storage Devices, Mouse, Audio & Printer Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the TouchPad surface and slide both fingers in the direction required (in a straight continuous motion).
Storage Devices, Mouse, Audio & Printer Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Storage Devices, Mouse, Audio & Printer 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. 3 AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components (see page C - 4). 1. 2. 3. 4. Attach the AC/DC adapter to the DC-In jack at the rear of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings (Win 7) 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management Power-Saving States 3 You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. It is recommended that you enable a password on wake up in order to protect your data.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Power Status Icon Color Power Off Off Sleep Blinking Green To Resume Press the Power Button Press the Power Button Closing the Lid If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Power Management 3 Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Follow these simple guidelines to get the best use out of your battery. Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g.
Power Management Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. • Reduce the amount of time before the display is turned off. • Close wireless, Bluetooth, modem or communication applications when they are not being used.
Power Management Battery Life 3 Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery” on page 6 - 3.
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances. • DO NOT expose the battery to fire or high temperatures, it may explode. • DO NOT connect the metal terminals (+, -) to each other. Caution Danger of explosion if battery is incorrectly replaced. Damaged Battery Warning Should you notice any physical defects (e.g.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 3 1. 2. Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Power Management 3 3 - 18
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu. 1. 2. 4 3. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below. Click to select the driver you wish to install, after installing each driver it will become grayed out.
Drivers & Utilities Windows 7 Driver Page Video Page 4 - 5 Audio Page 4 - 5 LAN Page 4 - 5 TouchPad Page 4 - 6 Card Reader/ExpressCard Page 4 - 6 GameKey Utility Page 4 - 6 Hot Key Page 4 - 6 HDMI-In Driver Page 4 - 6 Intel® Matrix Driver Installation (for RAID) Page 7 - 7 Wireless LAN Module Page 7 - 17 PC Camera Module Page 7 - 22 TV Tuner Module Page 7 - 30 Fingerprint Reader Module Page 7 - 33 Manual Driver Installation Click the Browse CD/DVD button in the Drivers Installer
Drivers & Utilities 4 Updating/Reinstalling Individual Drivers User Account Control (Win Vista) If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer).
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu. Driver Installation General Guidelines The driver installation procedure outlined in this Chapter (and in Chapter 7 Options & Modules), are accurate at the time of going to press. Drivers are always subject to upgrade and revision so the exact procedure for certain drivers may differ slightly.
Drivers & Utilities 4 TouchPad 1. Click 4.Install Touchpad Driver > Yes. 2. Click Next. 3. Click the button to accept the license, and then click Next. 4. Click Finish > Restart Now to restart the computer. Hot Key 1. Click 7.Install Hotkey Driver > Yes. 2. Click Next > Next. 3. Click Finish > Finish to restart your computer. Card Reader/ExpressCard 1. Click 5.Install Cardreader Driver > Yes. 2. Click Install > Finish. HDMI-In Driver 1. Click Back (button) and then click Option Drivers (button). 2.
Drivers & Utilities Optional Drivers Windows Update See the pages indicated for the driver installation procedures for any modules included in your purchase option. After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). 4 To enable Windows Update make sure you are connected to the internet: 1. 2. 3. 4. 5.
Drivers & Utilities 4 RAID Setup Consumer Infrared (for TV Tuner Remote) Note: Prior to setting up the RAID you will need to use an operable computer to copy the RAID driver to a USB flash drive before installing the Windows Vista operating system. See “Setting Up SATA RAID Mode” on page 7 - 2 for configuration instructions. See the install procedure in “TV Tuner Module” on page 7 - 29.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured right is for guideline purposes only. The POST screen on your computer may appear slightly different. If the Boot-time Diagnostic Screen is disabled (see page 5 - 9 as per the default setting), the POST screen will not appear.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities BIOS Settings Warning 5 Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Setup Defaults with . The Setup Utility The Phoenix Setup utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup To enter Setup, turn on the computer and press F2 during the POST.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu Phoenix SecureCore(tm) Setup Utility Figure 5 - 2 Main Menu 5 Main Mai n Advanced Security System Time: Boot System Date: [22:12:05] [11/23/2009] System Memory: Extended Memory: 628 KB 2039 MB BIOS Revision: KBC/EC Firmware Revision: ******** ******** 1st VGA Card: nVIDIA ******** 2nd VGA Card: nVIDIA ******** F1 Esc Help Exit Select Item Select Menu -/+ Enter Exit Item Specific Help , , or selects field.
BIOS Utilities System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed. BIOS Revision/VGA Card etc. (Main Menu) This item contains information on the BIOS version and video card etc., and is not user configurable.
BIOS Utilities SATA Mode Advanced Menu Phoenix SecureCore(tm) Setup Utility Main A dvanced Advanced Security Boot Exit Figure 5 - 3 5 Item Specific Help If you have installed the Advanced Menu Windows 7 operating system with either AHCI or RAID mode enabled, DO NOT disable the set mode (if you wish to disable the set mode you will need to reinstall the Windows 7 OS). F1 Esc Determines how SATA controller(s) operate.
BIOS Utilities Legacy USB Support: (Advanced Menu) Choose “Enabled” if you intend to use USB devices in systems which do not normally support USB functionality (e.g. DOS). The default setting is “Enabled” and does not need to be changed if you intend to use your USB devices in Windows. Boot-time Diagnostic Screen: (Advanced Menu) Use this menu item to enable/disable the Boot-time Diagnostic Screen. Enable this item to display the POST screen (see “The Power-On Self Test (POST)” on page 5 - 2).
BIOS Utilities Security Menu Security Menu Phoenix SecureCore(tm) Setup Utility Main Advanced Security Security Boot Exit = 5 Item Specific Help The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.
BIOS Utilities Set User Password (Security Menu) You can set a password for user mode access to the Phoenix SecureCore Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below). Many menu items in the Phoenix SecureCore Setup Utility cannot be modified in user mode. You can only set the user password after you have set the supervisor password.
BIOS Utilities Boot Menu Phoenix SecureCore(tm) Setup Utility Figure 5 - 5 Main Advanced Security Boot Exit Boot Menu 5 BIOS Screens Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS. BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages.
BIOS Utilities Exit Menu Phoenix SecureCore(tm) Setup Utility Main Advanced Security Boot Figure 5 - 6 Exit Exit Menu Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Utilities 5 5 - 14
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. Warranty Warning Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty. Turn the computer off and turn it over. Loosen screws 1 - 3 and carefully lift the battery 4 up. Remove the battery from the battery bay.
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 3. 4. 5. Remove the hard disk bay cover 3 . Remove screws 4 - 9 from the hard disk assembly. Remove the hard disk assembly by pulling the tab to disconnect it from the connector 10 .
Upgrading The Computer 6. 7. 8. 9. Remove screws 11 - 20 (depending on how many hard disks you have installed in the assembly). Separate the hard disk board 21 from the case 22 . Separate the hard disk(s) 23 & 24 from the case. Reverse the process to install any new hard disk(s).
Upgrading The Computer Removing the Hard Disk in the Secondary HDD Bay 1. 2. 3. 4. 5. 6. 7. Turn off the computer, and turn it over and remove the battery. The secondary hard disk bay is located under the battery compartment. Remove screws 25 - 28 . Slide the hard disk assembly in the direction of the arrow 29 . Lift the hard disk assembly 30 out of the compartment. Remove the screws 31 - 34 to release the hard disk from the case 35 . Reverse the process to install any new hard disk(s).
Upgrading The Computer Upgrading the System Memory (RAM) - 1 The computer has two memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDR III (DDR3) type memory modules (see “Memory” on page C - 2). The total memory size is automatically detected by the POST routine once you turn on your computer. 1. 2. Turn off the computer, and turn it over and remove the battery.
Upgrading The Computer 3. 4. Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 6 , and remove the cover 7 . 6 Figure 6 - 7 Component Bay Cover Removal 7 6 6 5. Loosen the heat sink screws in the order indicated 8 - 11 .
Upgrading The Computer 6. Carefully (it may be hot) remove the heat sink 12 . Figure 6 - 9 Heat Sink Removal 12 Contact Warning 6 Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. 7. 8. Gently pull the two release latches ( 13 & 14 ) on the sides of the memory socket in the direction indicated below. The RAM module 15 will pop-up, and you can remove it.
Upgrading The Computer 9. Pull the latches to release the second module if necessary. 10. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory socket. 11. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the socket as it will go. DO NOT FORCE the module; it should fit without much pressure. 12. Press the module in and down towards the mainboard until the socket levers click into place to secure the module.
Upgrading The Computer 14. Replace the component bay cover and make sure you reconnect the fan cable (see Figure 6 - 7 on page 6 - 9). 15. Replace all the component bay cover screws. 16. Restart the computer to allow the BIOS to register the new memory configuration as it starts up.
Upgrading The Computer Upgrading the System Memory (RAM) - 2 The computer has two memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDR III (DDR3) type memory modules (see “Memory” on page C - 2). The total memory size is automatically detected by the POST routine once you turn on your computer. 1. 2. Turn off the computer, and turn it over and remove the battery. Remove screws 1 & 2 from the bottom of the computer.
Upgrading The Computer 3. Turn the computer over, open the Lid/LCD, and carefully (a cable is connected to the underside of the LED cover module) unsnap up the LED cover module from point 3 on the right. Figure 6 - 13 LED Cover Module Removal 3 6 4. Lift up the LED cover module 4 and disconnect cable 5 .
Upgrading The Computer 5. Remove screws 6 - 10 from the keyboard. 6 7 8 9 10 Figure 6 - 15 Keyboard Screws 6 6. 7. Carefully lift the keyboard up, being careful not to bend the keyboard ribbon cable. Disconnect the keyboard ribbon cable 11 from the locking collar socket 12 .
Upgrading The Computer 8. Remove the keyboard 13 . Figure 6 - 17 Keyboard Removal 13 6 9. Remove screws 14 - 17 from the keyboard shielding plate 18 .
Upgrading The Computer 10. Gently pull the two release latches ( 19 & 20 ) on the sides of the memory socket in the direction indicated below. 11. The RAM module 21 will pop-up, and you can remove it. Figure 6 - 19 19 RAM Module Removal 21 Contact Warning 20 12. Pull the latches to release the second module if necessary. 13. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory socket. 14. The module’s pin alignment will allow it to only fit one way.
Upgrading The Computer 17. Snap the LED cover module down at the top of the module at points 22 & 23 . 18. Push the LED cover module down on the left side at point 24 , and then slide the module to the right (as illustrated) and snap down to secure it in place. 22 23 24 6 Figure 6 - 20 LED Cover Module Slide to the Right & Snap Down 19. Replace the screws on the bottom of the computer (see Figure 6 - 12). 20.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 4. Locate the hard disk bay cover and remove screws 1 & 2 . Remove the hard disk bay cover 3 . Remove the screw at point 4 , and use a screwdriver to carefully push out the optical device at point 5 . Reverse the process to install any new optical device.
Upgrading The Computer Warranty Warning Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty. 6 Figure 6 - 22 Component Bay Cover Screws & Cover Removal Upgrading the Video Card If you intend to upgrade or add another VGA card follow the procedures outlined here.
Upgrading The Computer 5. 6. Remove screws 8 - 10 (two video cards are pictured here) from the video card fan(s) and disconnect the fan cable(s) 11 (if two cards are present). Remove the RAM fan(s) 12 . Figure 6 - 23 Video Card Fan Screws 10 10 11 11 Caution 8 9 12 8 9 12 The heat sink, and video card area in general, contains parts which are subject to high temperatures. Allow the area time to cool before removing these parts.
Upgrading The Computer 7. Caution 6 The heat sink, and video card area in general, contains parts which are subject to high temperatures. Allow the area time to cool before removing these parts. 8. 9. Remove screws 13 - 16 from the heatsink in the order indicated on the label (two video cards are pictured here). Grip the handle 17 and carefully remove the heatsink 18 . Remove screws 19 - 20 from the video card.
Upgrading The Computer 10. Carefully remove the video card 21 . Caution 21 21 The heat sink, and video card area in general, contains parts which are subject to high temperatures. Allow the area time to cool before removing these parts.
Upgrading The Computer Installing a New Video Card 1. Prepare to fit the video card into the slot by holding it at about a 30° angle. 2. The card needs to be fully into the slot, and the video card and socket have a guide-key and pin which align to allow the card to fit securely. Contact Warning 6 Be careful not to touch the metal pins on the VGA card’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance.
Upgrading The Computer 3. 4. Fit the connectors firmly into the socket, straight and evenly. DO NOT attempt to push one end of the card in ahead of the other. Figure 6 - 28 Video Card Insertion Procedure 6 5. The card’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the socket as it will go (none of the gold colored contact should be showing). DO NOT FORCE the card; it should fit without much pressure.
Upgrading The Computer 6. 7. 8. 9. Secure the card with screws 19 - 20 (Figure 6 - 25 on page 6 - 22). Place the heatsink back on the card, and secure the screws in the order indicated in Figure 6 - 25 on page 6 - 22. Attach the video card fan and secure with the screws as indicated in Figure 6 - 23 on page 6 - 21. Reinsert the component bay cover, and secure with the screws as indicated in Figure 6 - 22 on page 6 - 20 (make sure you reconnect the fan cable before screwing down the bay cover).
Modules Chapter 7: Modules Overview This chapter contains the information on the various modules (some of which are optional) which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
Modules RAID Hard Disks All hard disks in a RAID should be identical (the same size and brand) in order to prevent unexpected system behavior. Setting Up SATA RAID Mode To configure your system in Striping (RAID 0) or Mirroring (RAID 1) modes (see Table 7 - 1, on page 7 - 3) you will require at least two identical (see sidebar) hard disks.
Modules RAID Level Description Table 7 - 1 RAID 0 Identical drives reading and writing data in parallel to increase performance. RAID 0 implements a striped disk array and the data is broken into blocks and each block is written to a separate disk drive. RAID Levels RAID 1 Identical drives in a mirrored configuration used to protect data. Should a drive that is part of a mirrored array fail, the mirrored drive (which contains identical data) will handle all the data.
Modules SATA RAID Setup Procedure (BIOS) 1. 2. Start-up your notebook computer and press to enter the BIOS. Go to the Advanced menu, select "SATA Mode" and press Enter (see page 5 - 8). • Select “RAID”. 3. 4. 5. 6. Press Esc and go to the Boot menu. Set the DVD-ROM Drive (make sure the Microsoft Windows 7 OS DVD is inserted) as the first device in the boot order from the Boot menu.
Modules RAID Setup (Intel Matrix) 1. As the computer starts up press Ctrl + i to enter RAID configuration menu. Intel(R) Rapid Storage Technology - Option ROM v9.5.0.1008 Copyright (C) 2003-09 Intel Corporation. All Rights Reserved. [ MAIN MENU 1. 2. 3. Create RAID Volume Delete RAID Volume Reset Disks to Non-RAID Figure 7 - 1 ] 4. 5. 6.
Modules 10. This will now return to the main menu. Intel(R) Rapid Storage Technology - Option ROM - 9.5.0.1008 Copyright (C) 2003-09 Intel Corporation. All Rights Reserved. [ MAIN MENU Figure 7 - 2 RAID Created 1. 2. 3. Create RAID Volume Delete RAID Volume Reset Disks to Non-RAID ] 4. 5. 6.
Modules Intel® Matrix Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 5.Install Matrix Driver > Yes. 4. Click Next > Next > Yes > Next. 5. Click Finish to restart the computer. The Intel Matrix Storage Console displays status information on your RAID configuration. Run the Intel® Matrix Storage Console from the Intel® Matrix Storage Manager in the Programs/All Programs menu.
Modules Intel® Matrix Storage Manager If a hard drive member of a RAID volume is reported as “Degraded” or “Failed” it may be possible to recover the volume. If the volume cannot be restored then you will need to recreate the RAID volume and restore the data from a back up. The Help menu (press F1 or select Contents and Index from the Help menu) provides instructions on how to recover or recreate RAID Volumes.
Modules RAID Volume Data Verification and Repair The RAID volume data verification process identifies any inconsistencies or bad data on a RAID 0 or RAID 1 volume. The table outlines what occurs for each RAID level: RAID Level Verify RAID 0 Bad blocks are identified. Verify & Repair N/A Bad blocks are reassigned. Bad blocks are identified. RAID 1 Data on the mirrored drive is compared to data on the source drive.
Modules Verifying and Repairing RAID Volume Data 1. 2. 3. Run the Intel® Matrix Storage Console from the Intel® Matrix Storage Manager in the Programs/All Programs menu. Click View > Advanced Mode. Right-click on the RAID volume and select either Verify Volume Data or Verify and Repair Volume Data. Figure 7 - 5 RAID Verification (Intel® Matrix Storage Console) 7 4. 5. Figure 7 - 6 The verification or verification and repair process will run and display progress.
Modules Bluetooth Module The optional Bluetooth module allows you to connect your computer to Bluetooth enabled devices such as other computers, desktop computers, mobile phones, printers, digital cameras, PDAs, headsets etc. using a short-range radio frequency. Wireless Device Operation Aboard Aircraft Use the Fn + F12 key combination or Touch Sensor Instant Key to toggle power to the Bluetooth module.
Modules Bluetooth Configuration in Windows 7 Add a Device Click Start, and click Control Panel and then click Devices and Printers (Hardware and Sound). Click Add a device to search for any available Bluetooth devices. 7 Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). To Turn the Bluetooth Module On 1. 2. 3.
Modules To Add a Bluetooth Device 1. 2. Access the Bluetooth Devices control panel and click Add a device. Double-click the device you want to pair with the computer. Pairing Options If a device has been previously connected then the pairing option menu will appear when you attempt subsequent connections. You can choose to have the computer create a pairing code for you, use the device’s existing pairing code or you can pair certain devices without using a code. Figure 7 - 8 3.
Modules 4. Figure 7 - 9 Pairing Codes Pairing Code Example 7 Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing. The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection procedure, and may require you to confirm a pairing code is correct on both devices. Follow the onscreen instructions to complete the pairing. 5. 6. 7.
Modules To Change Settings for the Bluetooth Device 1. 2. • • Click the taskbar icon and select Show Bluetooth Devices. Right-click on the device you want to change and click Properties to: Bluetooth Help Change the name of the device (click Bluetooth, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. Click the taskbar icon and select Open Settings.
Modules Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + F11 key combination/Touch Sensor Key to toggle power to the WLAN module, and check the LED to see if the module is powered on or not (see Table 1 - 3, on page 1 - 10/ Table 1 - 2, on page 1 - 8).
Modules Intel® Wi-Fi Link Series Driver Installation If you see the message “Found New Hardware” click Cancel to close the window. 1. Make sure the module is powered on, then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install Wireless Lan Driver > Yes. 4. An on-screen message will appear to show the progress of the WLAN installation. 5. When the message disappears the driver will be installed.
Modules Network and Sharing Center You can also use the Network and Sharing Center control panel in Windows (Network and Internet) to connect to any available wireless networks. Connecting to a Wireless Network in Windows 7 Make sure the Wireless LAN module is turned on. 1.
Modules 2. 3. 4. You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click “View or change settings in Network and Sharing Center” to access further options for the connection.
Modules Security Enabled Networks 5. 6. Click the taskbar icon to see any currently connected networks. To disconnect from the wireless network you can click the taskbar wireless icon click the active connection and then click Disconnect (button). You should try to make sure that any network you are connecting to is a secure network. 7 Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules Latest PC Camera Driver Information Check the Device Drivers & Utilities + User’s Manual disc and any accompanying insert pages, for the latest updated information on the PC Camera driver, which may override the information provided here. 7 PC Camera Display The PC Camera application software needs to be run while the default notebook LCD is the selected display device.
Modules PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone (Realtek High Definition Audio) and make sure the item is not disabled. 5. Double-click Microphone (or select Properties from the right-click menu). 6.
Modules Figure 7 - 16 Audio Setup for PC Camera Right-click 7 7 - 24 PC Camera Module
Modules Camera Application The WebCam application is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format. 1. 2. 3. Run the camera application from the desktop shortcut (it is recommended that you set the capture file before the capture process - see below). Go to the Capture menu heading (if you wish to capture audio check “PC Camera Audio Setup” on page 7 - 23) and select Start Capture.
Modules Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the camera program from the desktop shortcut. Go to Options and scroll down to select Video Capture Filter.... Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Modules Zoom The WebCam program allows you to zoom the camera in and out. 1. 2. Run the camera application from the desktop shortcut. Go to Zoom and select Zoom Out/Zoom In. Figure 7 - 18 Zoom/Setting Snapshot Folder 7 The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture. If you accidentally delete or move the folder, you can create a new Snapshot folder on the desktop in order to capture the files.
Modules TV Tuner Module If your purchase configuration includes the optional Hybrid (Analog & Digital) USB Mini-Card TV Tuner module, you will be supplied with a remote control unit and appropriate antenna and fittings for the module. Software support for the TV Tuner module is provided by Windows Media Center in Windows 7 (not included in Starter or Home Basic versions). A driver is provided on the Device Drivers & Utilities + User’s Manual disc for the remote control supplied with the TV Tuner.
Modules TV Tuner Module Support 7 Note that the TV Tuner module options in Windows 7 is supported by the Windows Media Center software which comes built-in to all the Windows 7 versions except Starter and Home Basic. If your purchase includes a TV Tuner option, and you are reconfiguring your system for a different system, you should install any Windows 7 version except Starter and Home Basic. Consumer Infrared Driver 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive.
Modules Digital TV Broadcast Signal The antenna is the most crucial factor in receiving a clear digital terrestrial TV broadcast signal. The passive antenna provided should provide a clear signal when placed beside a window. If the signal is not clear then you can purchase an active antenna (it should also be placed beside a window) to improve the signal. You should also check with any related government website which provides information on digital terrestrial TV coverage for your area.
Modules Password Warning If you set passwords for any of the security modules, NEVER forget your password. 7 The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. Fingerprint Reader Module The optional fingerprint reader Protector Suite Software provides a high level of security for your computer.
Modules Fingerprint Reader Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers. 3. Click 4.Install FingerPrint Driver > Yes. 4. Windows will configure Protector Suite 2009 and automatically restart the computer. 5. Click the tray icon , scan a finger or click Start > Programs/All Programs > Protector Suite > Control Center and then begin the enrollment process (see over).
Modules User Enrollment 1. Fingerprint Enrollment 2. Note that it is strongly recommended that you enroll more than one finger in case of injury etc. 3. 4. 5. Click Start > Programs/All Programs > Protector Suite > Control Center, or double click the taskbar icon (click Initialize). On the first run of the program you will be asked to click the Accept button to accept the license.
Modules 6. 7. Click the button above any of the fingers to begin the enrollment process for that finger. Swipe the finger until the progress bar reaches 100% to enroll that finger. Fingerprint Enrollment Note that it is strongly recommended that you enroll more than one finger in case of injury etc. 7 Figure 7 - 21 Fingerprint Enrollment Progress 8. Close the Protector Suite 2009 window.
Modules 9. Right-click the taskbar icon and select Start Control Center (and then swipe a finger) to allow you to Edit Fingerprints, register Applications, edit Settings and access the Help menu etc. You can also run the Control Center etc. from the Protector Suite item in the Programs/All Programs menu 10. Click “Help” to get more information on any topic. 11. You can also run the Tutorial, or Product Tour video to get more information. Figure 7 - 22 Control Center & Biomenu Help 7 12.
Modules Fingerprint Control Center Features Application Launcher The Application Launcher allows you to register applications to be launched when assigned to a particular finger. Simply copy the application icon on to one of the registered fingers and ten click OK to close the application window. Once registered the application will launch when you swipe the appropriate finger across the sensor.
Modules 7 7 - 38
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power Indicators (see “LED Indicators” on page 1 - 7) to see the computer’s power status. • Connections - Check all the cables to make sure that there are no loose connections anywhere.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Don’t over complicate things. The less you have to deal with then the easier the source of the problem may be found; Example - if your computer has many devices plugged into its ports, and a number of programs running, then it will be difficult to determine the cause of a problem. Try disconnecting all of the devices and restarting the computer with all the peripheral devices unplugged.
Troubleshooting Problems & Possible Solutions Problem Possible Cause - Solution You turned the power on but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The Battery LED power indicator , is blinking orange. Low Battery. Plug in the AC power source.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the vents/fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 15). Make sure you’re using the correct adapter.
Troubleshooting Problem You forget password. the Possible Cause - Solution boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting 8 Problem Possible Cause - Solution The TouchPad doesn’t work. The Touchpad has been disabled. Press the Touchpad toggle (Fn + F1) key combination (make sure you have installed the Touchpad driver. The system freezes or the screen goes dark. The system’s power saving features have timed-out. Use the AC/DC adapter, press a key on the keyboard, or press the sleep (Fn + F4) key combination, or press the power button if no LEDs are lit. The system never goes into a power saving mode.
Troubleshooting Problem Possible Cause - Solution When a DVD is played in Windows Media Player/ Media Center, the audio track in other languages (commentaries etc.) is not clear if connected to the S/PDIF-Out Jack. This is an issue with Windows Media Player/Media Center and audio output through the S/PDIFOut Jack. We recommend that you use the Power DVD application to play DVDs. Nothing appears on the screen when the PC Camera software is run.
Troubleshooting Problem Possible Cause - Solution No sound can be heard through an HDMI connected display device. You have not configured the HDMI audio output. See “HDMI Audio Configuration” on page 2 13. After installing the cardreader driver you receive the error message “0x000000D1” and the computer may restart. Where this is the case, install the beta cardreader driver version provided on the Device Drivers & Utilities +User’s Manual disc. 1. 2. 3.
Troubleshooting Problem Possible Cause - Solution After using the Fn + F11 key combination to switch the WLAN module off and have, restarted the computer, shut the computer down and started up again, or recovered from hibernate mode, you experience problems with powering the WLAN module on again. This is a known problem and Intel have provided a beta WLAN driver to address this issue. The beta WLAN driver is provided on the Device Drivers & Utilities +User’s Manual disc. 1. 2. 3. 4.
Troubleshooting Problem You have a RAID enabled and the system will not boot to Windows. 8 Possible Cause - Solution You may need to recover the RAID volumes. 1. 2. As the computer starts up press Ctrl + i to enter RAID configuration menu If the RAID volume’s Physical disks are marked in red, then press 4.Recovery Volume Options. 3. If you cannot access 4.Recovery Volume Options (i.e. it is grayed out) then press 5.Acceleration Options. 4. Press Enter and return to the main menu, then press 4.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the ports & jacks which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Ports and Jacks Item Card Reader Description The card reader allows you to use the following digital storage cards: MMC (MultiMedia Card) SD (Secure Digital) MS (Memory Stick) MS (Memory Stick Pro) A RS MMC (requires PC adapter) Mini SD (requires PC adapter) MS Duo (requires PC adapter) Cable (CATV) Antenna Jack Use this jack to connect a CATV cable if you have included the optional Mini-PCI TV Tuner in your purchase.
Interface (Ports & Jacks) Item Description e-SATA/USB Port This is a combined e-SATA (external Serial Advanced Technology Attachment)/ USB 2.0 compatible port. e-SATA / Plug external Serial ATA hard drives into this e-SATA (external Serial Advanced Technology Attachment) port. See “USB 2.0/1.1 Ports” on page A - 5 for USB port information. HDMI-Out Port HDMI The HDMI-Out (High-Definition Multimedia Interface) port is an audio/video connector interface for transmitting uncompressed digital streams.
Interface (Ports & Jacks) Item Description Microphone-In Jack Plug an external microphone in to this jack to record on your computer. Mini-IEEE 1394 Port This allows high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below). IEEE 1394 The Mini-IEEE 1394 ports only support SELF POWERED IEEE 1394 devices. RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB (Universal Serial Bus) 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Interface (Ports & Jacks) A A - 6
NVIDIA Video Driver Controls Appendix B: NVIDIA Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 17. NVIDIA Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. 1. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). 1. Click 1.Install Video Driver > Yes. 2. Click Next > Yes > Next. 3. Click Finish to restart the computer.
NVIDIA Video Driver Controls NVIDIA Control Panel To access the GeForce..... control panel from the desktop; rightclick the desktop, then click NVIDIA Control Panel. B NVIDIA Control Panel (Win 7) More advanced video configuration options are provided in the NVIDIA Control Panel tab. 1. 2. 3. 4. Open the Display Settings (see page 1 - 17) control panel. Click Advanced Settings (button). Click GeForce..... (tab). Click Start the NVIDIA Control Panel to make any video adjustments. 1. 2.
NVIDIA Video Driver Controls The NVIDIA Control Panel provides additional video configuration controls and tools which allow quick access to features such as display configuration, 3D Settings and Help menus etc. Navigating the Control Panel Navigate through the control panels in much the same way as you would a web page. Click on the sub-heading tasks in the left menu (and on the highlighted links) for information. Use the buttons on the top left to go back, forward etc.
NVIDIA Video Driver Controls The Help menus provide index and search features, and direct links to the NVIDIA website etc.
NVIDIA Video Driver Controls Display Devices Note that you can use a DVI cable connected to the DVI-Out port, or an HDMI (High-Definition Multimedia Interface) cable connected to the HDMI-Out port to connect an external display (if you are using an older type of monitor you can use a converter to convert the signal from DVI to VGA). See your display device manual to see which formats are supported. 1. 2. 3. The built-in LCD. An external display connected to the DVI-Out Port.
NVIDIA Video Driver Controls SLI Configuration & Multiple Displays Note that if SLI configuration is enabled only a Single display may be used as the display device. B DO NOT use the Fn + F7 key combination to toggle through display options when SLI is enabled. SLI supports only a Single display, and attempting to configure dual displays may cause an error. Use the NVIDIA control panel to select the display to be used.
NVIDIA Video Driver Controls Configuring an External Display using the NVIDIA Control Panel You can use the NVIDIA control panel to configure any attached displays. 1. 2. 3. 4. Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Go to NVIDIA Control Panel (see page B - 2). Double-click Display (if the sub-menus are not visible), and then click Set up multiple displays. Any attached display will appear under “1.Select the displays you want to use.
NVIDIA Video Driver Controls Duplicating the Displays 1. 2. 3. 4. 5. 6. Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Go to NVIDIA Control Panel (see page B - 2). Double-click Display (if the sub-menus are not visible), and then click Set up multiple displays. Any attached display will appear under “1.Select the displays you want to use.” Click the tickbox alongside any display you wish to use. Right-click one of the display icons and click “Duplicate displays....
NVIDIA Video Driver Controls Extending the Display 1. 2. 3. 4. 5. Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Go to NVIDIA Control Panel (see page B - 2). Double-click Display (if the sub-menus are not visible), and then click Set up multiple displays. Click to select a primary display under “1.Select the displays you want to use.” Right-click one of the display icons and click “Extend Desktop on this display....” to extend the desktop across both displays.
NVIDIA Video Driver Controls Changing the Primary Display on Extended Displays 1. 2. 3. If you want to switch the primary display if the displays are extended then rightclick the secondary display icon. Select Make this the Windows primary display. Click Apply > Yes to save the change. Figure B - 7 Switch Primary Display Select Apply > Yes to save changes B Right-click to select the secondary display and select Make this the Windows primary display.
NVIDIA Video Driver Controls Attaching Other Displays (Win 7) Configuring an External Display in Windows 7 1. 2. 3. 4. Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Go to the Screen resolution control panel. Click the Detect button. The computer will then detect any attached displays.
NVIDIA Video Driver Controls 5. You can configure the displays from the Multiple Displays menu. Figure B - 9 Screen Resolution Multiple Display Options (Win 7) B • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) • Extend these displays - Treats both connected displays as separate devices • Show desktop only on 1/2 - Only one of your displays is used.
NVIDIA Video Driver Controls Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configuration and modes (this is particularly useful when attaching a projector) in Windows 7. 1. 2. 3. 4. Attach your external display to the external monitor port and turn it on. Press the + P key combination. An on-screen menu will pop up.
NVIDIA Video Driver Controls SLI Configuration & Multiple Displays Note that if SLI configuration is enabled only a Single display may be used as the display device. B SLI Multi GPU Configuration This computer features an NVIDIA Scalable Link Interface (SLI) that improves graphic quality and performance by combining dual NVIDIA GPUs (two video cards are required) in a single system. To enable/disable SLI Configuration: 1. 2. Go to NVIDIA Control Panel (see page B - 2).
NVIDIA Video Driver Controls SLI Multi GPU Configuration & Battery Power Note that due to the high power and system demands created by enabling SLI Configuration, you should not enable SLI configuration if your computer is powered by battery only. If you attempt to run an SLI configuration when the computer is powered by the battery only, then system problems may occur. • If the computer is currently powered by battery only do not enable SLI configuration.
NVIDIA Video Driver Controls Detect Displays To get a full range of display options click “My display is not shown in the list...”. HDMI Audio Setup Enabling TV Display To display desktop images on a TV, connect the TV to your computer by using an HDMI cable/DVI cable from the TV to the HDMI-Out port/DVI-Out port (if supported by your TV). You will need to enable the TV display from the NVIDIA Control Panel as per the instructions on B - 7. The TV will appear as a display option (1.
NVIDIA Video Driver Controls Changing the TV Signal Format 1. 2. 3. 4. When the TV is enabled as a display device click the sub-menus under Video & Television. Click “Change the signal or HD format”. Select the connector or format you want to use (the menu that appears will depend upon your type of connector). Apply the settings, and then click Yes to save the changes.
NVIDIA Video Driver Controls The NVIDIA Control Panel provides additional configuration controls to adjust the TV settings in the Video & Television menu.
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.
Specifications Processor Display BIOS Intel® Core i7-720QM Processor: 1.6GHz 45nm (45 Nanometer) Process Technology, 6M L3 Cache & FSB 1333MHz - TDP 45W rPGA988A Package 18.4" HD+/ FHD (1920 * 1080) TFT LCD One 32Mb Flash ROM Phoenix™ BIOS Intel® Core i7-820QM Processor: 1.73GHz 45nm (45 Nanometer) Process Technology, 8M L3 Cache & FSB 1333MHz - TDP 45W rPGA988A Package Intel® Core i7-920XM Processor: 2.
Specifications Keyboard & Pointing Device Interface Communication Full Size Winkey Keyboard with Numeric Keypad Built-In TouchPad (with Multi Gesture Functionality) Eight Touch Sensor Instant Keys (Color, CCD, Bluetooth, WLAN, Internet, Silent Mode, Sound Effect, Mute) Eight Gaming Keys G1 ~ G8 Four USB 2.
Specifications Operating System Environmental Spec Windows® 7 Note that the TV Tuner module (factory) option in is supported by the Windows Media Center software. Windows Media Center is not included in Starter or Home Basic versions of Windows 7. Temperature Operating: 5°C - 35°C Non-Operating: -20°C - 60°C Relative Humidity Operating: 20% - 80% Non-Operating: 10% - 90% Power Management Physical Dimensions & Weight Supports Wake on LAN Supports Wake on USB 439mm (w) * 299mm (d) * 44mm (h) Around 5.
