Service manual
Table Of Contents
- Manual
- Preface
- 1: Introduction
- 2: Disassembly
- Overview
- Disassembly Steps
- To remove the hard disk drive assembly:
- To remove the CD device(s):
- To remove the RF module:
- To remove the system memory:
- To remove the CPU:
- To remove the modem:
- To remove the floppy disk drive assembly:
- To remove the optional wireless LAN module:
- To remove the inverter board:
- To remove the mainboard:
- To remove the LCD/LED board:
- To remove the base cover:
- To remove the speaker units:
- To remove the bridge board:
- To remove the CD device base brackets:
- To remove the USB board:
- To remove the power supply unit:
- Removing the Hard Disk Drive Assembly
- Removing the CD Devices
- Removing the RF Module
- Removing the System Memory
- Removing the CPU
- Removing the Modem
- Removing the Floppy Disk Drive Assembly
- Removing the Wireless LAN Module
- Removing the I/O Bracket
- Removing the Rear Bracket
- Removing the Inverter Board
- Removing the Mainboard
- Separating the Bottom Case from the LCD & Mainboard Assembly
- Removing the LCD
- Removing the LED Board
- Removing the Base Cover
- Removing the Speaker Units
- Removing the Bridge Board
- Removing the CD Device Base Brackets
- Removing the USB Board
- Removing the Power Supply Unit
- Appendix A: Part Lists
- Appendix B: Schematic Diagrams
- Table 1 - 1 Schematic Diagram
- System Block Diagram
- Clock Generator
- DRCG Panel Type
- CPU (P4 mPGA 478) - 1 of 2
- CPU (P4 mPGA478) - 2 of 2
- MCH (CPU, HUB, AGP) - 1 of 2
- MCH (RDRAM, PCI) - 2 of 2
- RAMBUS A,B
- CPU Decoupling
- ATI Mobility M6 - 1 of 3
- ATI Mobility M6 - 2 0f 3
- ATI Mobility M6 - 3 0f 3
- VRAM Terminator
- Z3, LVDS
- Micro-P, LCD PWR
- ICH2 - 1 of 2
- ICH2 - 2 of 2
- Audio Codec, AMP
- IDE, PCI Reset
- PCMCIA 1394
- 1394 PHY, PCMCIA Ejecter
- LAN 8139C
- Super I/O
- USB, Bluetooth
- LPT, IR/RF
- Mini PCI, MDC
- Power - 1 of 2
- Power - 2 of 2
- SSC, VGA Power
- VRAM DDR - 1 of 2
- VRAM DDR - 2 of 2
- Video In
- External USB Board
- LED Board
- Inverter Board - Page 1 of 2
- Inverter Board - Page 2 of 2
- Appendix C: Switches
- Appendix D: Updating the FLASH ROM BIOS
Preface
III
Preface
About this Manual
This manual is intended for service personnel who have completed sufficient training to undertake the maintenance and
inspection of personal computers.
It is organized to allow you to look up basic information for servicing and/or upgrading components of the LCD PC. The
following information is included:
Chapter 1, Introduction, provides general information about the location of system elements and their specifications.
Chapter 2, Disassembly, provides step-by-step instructions for disassembling parts and subsystems.
Appendix A, Part Lists
Appendix B, Schematic Diagrams
Appendix C, Switches
Appendix D, Updating the FLASH ROM BIOS
Related Documents
You may also need to consult the following manual for additional information:
User’s Manual on CD
This describes the LCD PC’s features and the procedures for operating the computer and its ROM-based setup program.
It also describes the installation and operation of the utility programs provided with the LCD PC.