Service manual
Table Of Contents
- Manual
- Preface
- 1: Introduction
- 2: Disassembly
- Overview
- Disassembly Steps
- To remove the hard disk drive assembly:
- To remove the CD device(s):
- To remove the RF module:
- To remove the system memory:
- To remove the CPU:
- To remove the modem:
- To remove the floppy disk drive assembly:
- To remove the optional wireless LAN module:
- To remove the inverter board:
- To remove the mainboard:
- To remove the LCD/LED board:
- To remove the base cover:
- To remove the speaker units:
- To remove the bridge board:
- To remove the CD device base brackets:
- To remove the USB board:
- To remove the power supply unit:
- Removing the Hard Disk Drive Assembly
- Removing the CD Devices
- Removing the RF Module
- Removing the System Memory
- Removing the CPU
- Removing the Modem
- Removing the Floppy Disk Drive Assembly
- Removing the Wireless LAN Module
- Removing the I/O Bracket
- Removing the Rear Bracket
- Removing the Inverter Board
- Removing the Mainboard
- Separating the Bottom Case from the LCD & Mainboard Assembly
- Removing the LCD
- Removing the LED Board
- Removing the Base Cover
- Removing the Speaker Units
- Removing the Bridge Board
- Removing the CD Device Base Brackets
- Removing the USB Board
- Removing the Power Supply Unit
- Appendix A: Part Lists
- Appendix B: Schematic Diagrams
- Table 1 - 1 Schematic Diagram
- System Block Diagram
- Clock Generator
- DRCG Panel Type
- CPU (P4 mPGA 478) - 1 of 2
- CPU (P4 mPGA478) - 2 of 2
- MCH (CPU, HUB, AGP) - 1 of 2
- MCH (RDRAM, PCI) - 2 of 2
- RAMBUS A,B
- CPU Decoupling
- ATI Mobility M6 - 1 of 3
- ATI Mobility M6 - 2 0f 3
- ATI Mobility M6 - 3 0f 3
- VRAM Terminator
- Z3, LVDS
- Micro-P, LCD PWR
- ICH2 - 1 of 2
- ICH2 - 2 of 2
- Audio Codec, AMP
- IDE, PCI Reset
- PCMCIA 1394
- 1394 PHY, PCMCIA Ejecter
- LAN 8139C
- Super I/O
- USB, Bluetooth
- LPT, IR/RF
- Mini PCI, MDC
- Power - 1 of 2
- Power - 2 of 2
- SSC, VGA Power
- VRAM DDR - 1 of 2
- VRAM DDR - 2 of 2
- Video In
- External USB Board
- LED Board
- Inverter Board - Page 1 of 2
- Inverter Board - Page 2 of 2
- Appendix C: Switches
- Appendix D: Updating the FLASH ROM BIOS
Disassembly
2 - 12 Removing the RF Module
2.Disassembly
Removing the RF Module
1. Turn off the computer and pull the LCD up and forward to allow easier access to the latch "1".
2. Slide the latch to unlock the module case and hold in place as you pull the case out of the bay (the left bay latch
slides to the right).
3. Pull the RF module "
2" case out of the bay.
4. Turn the case over and remove screws "
3" - "5", then remove the case cover "6".
5. If there is an RF module "
7" into the case, remove screws at positions "8" and "9" and disconnect cable "10".
Figure 2 - 3
RF Module
Removal
Sequence
a. Slide the latch and
hold in place.
b. Pull the module
case out of the
bay.
c. Remove the three
screws from the
case cover.
d. Remove the case
cover.
e. If there is an RF
module in the
case remove the
screws.
f. Remove the
cable. and RF
module.
2. RF module case
7. Optional RF
module
• 5 screws (if mod-
ule is included)
1
a.
2
b. c.
3
4
5
6
7
8
9
10
e.d. f.