Service manual
Table Of Contents
- Manual
- Preface
- 1: Introduction
- 2: Disassembly
- Overview
- Disassembly Steps
- To remove the hard disk drive assembly:
- To remove the CD device(s):
- To remove the RF module:
- To remove the system memory:
- To remove the CPU:
- To remove the modem:
- To remove the floppy disk drive assembly:
- To remove the optional wireless LAN module:
- To remove the inverter board:
- To remove the mainboard:
- To remove the LCD/LED board:
- To remove the base cover:
- To remove the speaker units:
- To remove the bridge board:
- To remove the CD device base brackets:
- To remove the USB board:
- To remove the power supply unit:
- Removing the Hard Disk Drive Assembly
- Removing the CD Devices
- Removing the RF Module
- Removing the System Memory
- Removing the CPU
- Removing the Modem
- Removing the Floppy Disk Drive Assembly
- Removing the Wireless LAN Module
- Removing the I/O Bracket
- Removing the Rear Bracket
- Removing the Inverter Board
- Removing the Mainboard
- Separating the Bottom Case from the LCD & Mainboard Assembly
- Removing the LCD
- Removing the LED Board
- Removing the Base Cover
- Removing the Speaker Units
- Removing the Bridge Board
- Removing the CD Device Base Brackets
- Removing the USB Board
- Removing the Power Supply Unit
- Appendix A: Part Lists
- Appendix B: Schematic Diagrams
- Table 1 - 1 Schematic Diagram
- System Block Diagram
- Clock Generator
- DRCG Panel Type
- CPU (P4 mPGA 478) - 1 of 2
- CPU (P4 mPGA478) - 2 of 2
- MCH (CPU, HUB, AGP) - 1 of 2
- MCH (RDRAM, PCI) - 2 of 2
- RAMBUS A,B
- CPU Decoupling
- ATI Mobility M6 - 1 of 3
- ATI Mobility M6 - 2 0f 3
- ATI Mobility M6 - 3 0f 3
- VRAM Terminator
- Z3, LVDS
- Micro-P, LCD PWR
- ICH2 - 1 of 2
- ICH2 - 2 of 2
- Audio Codec, AMP
- IDE, PCI Reset
- PCMCIA 1394
- 1394 PHY, PCMCIA Ejecter
- LAN 8139C
- Super I/O
- USB, Bluetooth
- LPT, IR/RF
- Mini PCI, MDC
- Power - 1 of 2
- Power - 2 of 2
- SSC, VGA Power
- VRAM DDR - 1 of 2
- VRAM DDR - 2 of 2
- Video In
- External USB Board
- LED Board
- Inverter Board - Page 1 of 2
- Inverter Board - Page 2 of 2
- Appendix C: Switches
- Appendix D: Updating the FLASH ROM BIOS
Disassembly
2 - 4 Disassembly Steps
2.Disassembly
Disassembly Steps
The following lists the disassembly steps, and on which page to find the related information. PLEASE PERFORM THE
DISASSEMBLY STEPS IN THE ORDER INDICATED.
To remove the hard disk drive assembly:
1.Remove the hard disk drive assembly page 2 - 10
To remove the CD device(s):
1.Remove the CD Device page 2 - 11
To remove the RF module:
1.Remove the RF module page 2 - 12
To remove the system memory:
1.Remove the LCD hinge cover page 2 - 14
2.Remove the IDE shielding plate page 2 - 14
3.Remove the LCD back cover page 2 - 15
4.Remove the LCD shielding plate page 2 - 16
5.Remove the system memory page 2 - 16
To remove the CPU:
1.1.Remove the LCD hinge cover page 2 - 14
2.Remove the IDE shielding plate page 2 - 14
3.Remove the LCD back cover page 2 - 15
4.Remove the LCD shielding plate page 2 - 16
5.Remove the CPU page 2 - 17
Memory Module
Warning
There must be a mem-
ory module present in
both DIMM sockets to
make sure the compu-
ter will boot up. The
memory modules must
be the same size and
specification. The op-
tions are listed in the
table below.