Service manual
Table Of Contents
- Manual
- Preface
- 1: Introduction
- 2: Disassembly
- Overview
- Disassembly Steps
- To remove the hard disk drive assembly:
- To remove the CD device(s):
- To remove the RF module:
- To remove the system memory:
- To remove the CPU:
- To remove the modem:
- To remove the floppy disk drive assembly:
- To remove the optional wireless LAN module:
- To remove the inverter board:
- To remove the mainboard:
- To remove the LCD/LED board:
- To remove the base cover:
- To remove the speaker units:
- To remove the bridge board:
- To remove the CD device base brackets:
- To remove the USB board:
- To remove the power supply unit:
- Removing the Hard Disk Drive Assembly
- Removing the CD Devices
- Removing the RF Module
- Removing the System Memory
- Removing the CPU
- Removing the Modem
- Removing the Floppy Disk Drive Assembly
- Removing the Wireless LAN Module
- Removing the I/O Bracket
- Removing the Rear Bracket
- Removing the Inverter Board
- Removing the Mainboard
- Separating the Bottom Case from the LCD & Mainboard Assembly
- Removing the LCD
- Removing the LED Board
- Removing the Base Cover
- Removing the Speaker Units
- Removing the Bridge Board
- Removing the CD Device Base Brackets
- Removing the USB Board
- Removing the Power Supply Unit
- Appendix A: Part Lists
- Appendix B: Schematic Diagrams
- Table 1 - 1 Schematic Diagram
- System Block Diagram
- Clock Generator
- DRCG Panel Type
- CPU (P4 mPGA 478) - 1 of 2
- CPU (P4 mPGA478) - 2 of 2
- MCH (CPU, HUB, AGP) - 1 of 2
- MCH (RDRAM, PCI) - 2 of 2
- RAMBUS A,B
- CPU Decoupling
- ATI Mobility M6 - 1 of 3
- ATI Mobility M6 - 2 0f 3
- ATI Mobility M6 - 3 0f 3
- VRAM Terminator
- Z3, LVDS
- Micro-P, LCD PWR
- ICH2 - 1 of 2
- ICH2 - 2 of 2
- Audio Codec, AMP
- IDE, PCI Reset
- PCMCIA 1394
- 1394 PHY, PCMCIA Ejecter
- LAN 8139C
- Super I/O
- USB, Bluetooth
- LPT, IR/RF
- Mini PCI, MDC
- Power - 1 of 2
- Power - 2 of 2
- SSC, VGA Power
- VRAM DDR - 1 of 2
- VRAM DDR - 2 of 2
- Video In
- External USB Board
- LED Board
- Inverter Board - Page 1 of 2
- Inverter Board - Page 2 of 2
- Appendix C: Switches
- Appendix D: Updating the FLASH ROM BIOS
Introduction
System Specifications 1 - 3
1.Introduction
Display
• ATI M6-P Integrated AGP™ 4X
• Integrated 128-bit 2D/3D Graphics Accelerator
Advanced HW Acceleration for DVD Playback (Motion Compensation engine and IDCT)
Fully DirectX 8 Compliant Graphics Engine
• External memory of 32MB or 64MB of DDR SGRAM on board (factory option)
• Dual-View Display Monitor
Storage
• One 3.5” 1.44MB 3-mode FDD (slim type)
• One 3.5” HDD
• Two slim storage bays for CD Devices
Device Bay Right: Changeable with CD-ROM/CD-RW/DVD/Combo drive
Device Bay Left: Changeable with CD-ROM/CD-RW/DVD/Dummy or RF module
Audio
• AC97’ 2.2 compatible
• Two Built-In speakers (3W)
• Three audio jacks for headphone-out, line-in, and microphone-in
PC Card Sockets
• Supports two Type II or one Type III PCMCIA slots
• Integrated IEEE 1394a controller