Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. VI • Only use a power adapter approved for use with this computer.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire. • Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC adapter and cables. Stow them in the carrying bag. The AC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. • Position the display directly in front of you at a comfortable viewing distance. • Adjust the display-viewing angle to find the best position.
Preface Contents Notice ...........................................................................I FCC Statement ...................................................II Instructions for Care and Operation ................. IV Power Safety ..................................................... VI Battery Precautions ..........................................VII Cleaning ........................................................ VIII Servicing ........................................................
Preface Audio "DJ" CD Player ...........................................2-12 Adding a Printer .....................................................2-14 USB Printer ..........................................................2-14 Install Instructions: ..............................................2-14 Parallel Printer ......................................................2-14 Power Management Overview ..................................................................
Preface Module Drivers ....................................................4-24 Wireless LAN (WinXP) ......................................4-24 WLAN & Bluetooth Combo (WinXP) ...............4-24 TV Tuner (WinXP) .............................................4-24 PC Camera (WinXP) ...........................................4-24 BIOS Utilities Overview ..................................................................5-1 The Power-On Self Test (POST) .............................5-2 Failing the POST .........
Preface Driver Installation .................................................7-5 Bluetooth/WLAN Combo Module ...........................7-6 Combo Module Bluetooth Driver Installation ......7-7 Combo Module WLAN Driver Installation ..........7-8 TV Tuner Module Options .......................................7-9 AverMedia M102 Mini-PCI TV Tuner Module ..7-10 Installing the AverTV Utility Software ..............7-10 Installing the InterVideo WinDVD 4 Software ..
Preface Headphone-Out Jack ...............................................A-5 Security Lock Slot ...................................................A-5 NVIDIA Video Driver Controls NVIDIA Video Driver Installation ......................... B-1 NVIDIA Display Properties .................................... B-2 Additional Properties ........................................... B-3 NVIDIA nView Desktop Manager ...................... B-5 Display Devices .......................................................
Preface XVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D The Storage Devices (hard disk, optical device, 10-in-1 Card Reader, PC Card), Mouse, Audio & Printer.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you. Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide System Software Your computer may already come with system software pre-installed.
1 Quick Start Guide System Startup 1. 2. 3. 2 4. 1 5. 1 6. 1. 2. LCD Latches 7. LED Power & Communication 8. Indicators Figure 1 - 1 - Top Panel with LCD Closed Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC adapter.
Quick Start Guide System Map: Top View with LCD Panel Open 1 Wireless Device Operation Aboard Aircraft 2 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. The key combination Fn + F11 toggles power to the WLAN module, Fn + F12 to the Bluetooth module. 1. 3 6 5 7 4 9 4 8 10 Optional Built-In PC Camera 2. LCD 3. LED Power & Communication Indicators 4. Speakers 5.
1 Quick Start Guide LED Indicators Table 1 - 2 - LED Power & Communication Indicators The two sets of LED indicators (LED Status Indicators and LED Power & Communication Indicators) on the computer display helpful information about the current status of the computer.
Quick Start Guide AP-Key Buttons Function Keys & Numeric Keypad These buttons access the internet, e-mail or a user-defined application with one quick button press. Make sure you install the driver to enable the AP-Key Button functions (refer to “What to Install” on page 4 - 15). The keyboard has an embedded numerical keypad for easy numeric data input (see Figure 1 - 3).
1 Quick Start Guide Table 1 - 4 - Function Keys Keys Description Fn Function Key Fn + F2 Fan Automatic Control / Full Power Fn + F3 Mute Toggle Fn + F4 Sleep Toggle Fn + F5 Decrease Audio Volume Fn + F6 Increase Audio Volume Fn + F7 Display Toggle Fn + F8 Decrease LCD Brightness Fn + F9 Increase LCD Brightness Fn + F10 TouchPad Module Toggle Fn + F11 WLAN Toggle Fn + F12 Bluetooth Module Toggle Fn + Scr Lk Scroll Lock Toggle Figure 1 - 3 - Keyboard Function Keys Num Lk & Scr Lk
Quick Start Guide System Map: Front & Rear Views 1 4 Figure 1 - 4 Front & Rear Views 1 3 2 4 2 3. Audio "DJ" Player The built-in standalone audio CD player gives you direct hardware control for audio CDs (MP3 compatible) when the computer is shut down, but has a working power source. 5 5 6 7 1. 2. 8 9 10 11 12 13 14 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
1 Quick Start Guide System Map: Left View Figure 1 - 5 Left View 1. 2. 3. S-Video-Out Jack 4 * USB 2.0 Ports 2 * Mini-IEEE 1394a Port 4. Line-In Jack 5. S/PDIF-Out Jack 6. Microphone-In Jack 7. Headphone-Out Jack 8. 10-in-1 Card Reader 9. PC Card Slot 10.
Quick Start Guide System Map: Right View Figure 1 - 6 - Right View 1. 2 3 1 2. 3. Primary Optical Device Drive Bay (for CD/DVD Device) Secondary Optical Device Drive Bay (for CD/DVD Device) Security Lock Slot Changing DVD Regional Codes Go to the Control Panel and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/CD-ROM drives.
1 Quick Start Guide System Map: Bottom View Figure 1 - 7 - Bottom View 1. 2. 3. 4. 5. 6. 7. Battery Vent/Fan Intake Memory (RAM) Cover Hard Disk Cover Sub Woofer Video Card Cover CPU Cover 7 CPU The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 2 1 3 2 2 5 6 4 2 Battery Information Always completely discharge, then fully charge, a new battery before using it.
Quick Start Guide Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
1 Quick Start Guide Video Features Video Driver Controls This computer features different (NVIDIA or ATI) PCI Express video card options (see “Video Card Options” on page D - 3). You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate video driver is installed.
Quick Start Guide NVIDIA Display Properties 1 2 3 ATI Display Properties 1 2 3 Figure 1 - 9 - Display Properties Desktop Video Features 1 - 15 1
1 Quick Start Guide Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display or TV as your display device. A VGA monitor/Flat Panel Display connects to the DVI-Out port, a TV to the SVideo-Out jack. The following display modes are available (see Appendix B:“NVIDIA Video Driver Controls” or Appendix C:“ATI Video Driver Controls” for details).
Quick Start Guide Power Management Features The Power Options control panel in Windows (see page 1 - 13) allows you to configure power management features for your computer. You may conserve power through individual components such as the monitor or hard disk (by means of Power Schemes), or you may use either Standby or Hibernate mode to conserve power throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 - 10).
1 Concise User’s Guide 1 - 18
Storage Devices, Mouse, Audio & Printer Chapter 2: Storage Devices, Mouse, Audio & Printer Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • • • The Hard Disk Drive The Optical (CD/DVD) Device 10-in-1 Card Reader The PC Card Slot The TouchPad & Buttons/Mouse The Infrared Transceiver Audio Features Audio "DJ" Player Adding a Printer (general guidelines) Overview 2 - 1 2
Storage Devices, Mouse, Audio & Printer 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" hard disk drives with a height of 9.
Storage Devices, Mouse, Audio & Printer Optical Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see “Storage Options” on page D - 4). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (“Boot Menu” on page 5 13).
Storage Devices, Mouse, Audio & Printer 2 CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Disk Eject Warning Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.
Storage Devices, Mouse, Audio & Printer DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 11. .
Storage Devices, Mouse, Audio & Printer 2 Operating System Installation Warning If you are installing an operating system (e.g. Windows XP), and have a 10-in-1 Card Reader present, make sure to set the Card Reader option in the BIOS to “Disabled”. See “Card Reader: (Advanced Menu)” on page 5 - 10. 10-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device.
Storage Devices, Mouse, Audio & Printer PC Card Slot 2 The computer is equipped with a PCMCIA 3.3V/5V slot for one type II PC Card. Inserting and Removing PC Cards • Align the PC Card with the slot and push it in until it locks into place. • To remove a PC Card, simply press the eject button 1 next to the slot.
Storage Devices, Mouse, Audio & Printer 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Storage Devices, Mouse, Audio & Printer Configuring the Infrared Settings for FIR To configure your computer for Fast Infrared (FIR) communication follow these steps: 1. 2. 3. 4. 5. 6. Click Start, point to Settings and click Control Panel (or just click Start > Control Panel). Double-click Wireless Link (Printers and Other Hardware Category) icon. Click Hardware (tab), and click the Properties button, then click the Advanced (tab).
Storage Devices, Mouse, Audio & Printer 2 Sound Volume Adjustment How high the sound volume can be set using the volume control knob depends on the setting of the volume control within Windows. Click the Volume icon on the taskbar to check the setting.
Storage Devices, Mouse, Audio & Printer 8 Channel Sound Support 2 If you wish to configure your system for 8 channel sound support, then the following ports should be used as outputs.
Storage Devices, Mouse, Audio & Printer 2 Disk Eject Warning Don’t try to eject a CD/ DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice. Audio "DJ" CD Player The built-in standalone audio CD player gives you direct hardware control for audio CDs/DVDs when the computer is shut down, but has a working power source. 1. Make sure that the computer is shut down (i.e.
Storage Devices, Mouse, Audio & Printer 12 1 2 3 11 10 TV Tuner Option 6 4 7 8 9 5 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Storage Devices, Mouse, Audio & Printer 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel port. Turn ON the printer, then the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer uses the ACPI power management system. Power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 Power Button as Standby or Hibernate Button If you are using a fully ACPI-compliant OS, (such as Windows XP) you can use the OS’s “Power Options” control panel to set the power button to send the system into Standby or Hibernate mode (see your OS’s documentation, or “Configuring the Power Button” on page 3 - 8 for details). The Power Sources The computer can be powered by either an AC adapter or a battery pack. AC Adapter Use only the AC adapter that comes with your computer.
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Standby/Hibernate/Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation The system can resume from Monitor or Hard Disk Standby by pressing a key on the keyboard. Figure 3 - 1 Power Schemes 3 - 4 Power Schemes Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes.
Power Management Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Power Management System Power Options 3 You can use the system power options to stop the computer’s operation and restart where you left off. This system features Standby and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - Figure 3 - 2 on page 3 - 7). Hibernate Mode vs. Shutdown Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to turn it on.
Power Management Standby Standby saves the least amount of power, but takes the shortest time to return to full operation. During Standby the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Standby mode to save power.
Power Management Configuring the Power Button The power button may be set to send the computer in to either Standby or Hibernate mode (Figure 3 - 3). In Standby mode, the LED will flash green. In Hibernate mode the LED will be off. If you are in a power saving mode set to save power through individual components (e.g. hard disk, monitor), the LED will remain green.
Power Management Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery Warning New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 12 for instructions on how to do this). Battery Life Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached.
Power Management 3 Conserving Battery Power To conserve battery power: Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC adapter. Close modem or communication applications when they are not being used. Remove any unused PC Cards from the computer (PC Cards quickly use up battery power even if the system enters sleep mode). Battery life may be shortened through improper maintenance.
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Power Management 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities ATA Mode Configuration If you wish to configure your hard disk(s) in ATA mode, then see the instructions on following next pages. You will need an external floppy drive attached to install the driver ATA driver when setting up Windows. 4 Jumper Settings for Two Parallel ATA Hard Disks If you are using Parallel ATA (PATA) hard disk drives.
Drivers & Utilities ATA Mode Setup 1. 2. 3. 4. 5. Prepare a formatted blank 3.5" 1.44MB floppy diskette, and an external USB floppy disk drive. Create an ATA Driver Diskette by using an operable computer to copy the Drivers\RAID\ATA folder from the Device Drivers & Utilities + User’s Manual CD-ROM (Navigate/Browse.. to D:Drivers\RAID\ATA) to the blank floppy diskette. Connect the external USB floppy disk drive to the notebook computer.
Drivers & Utilities 6. Select the CD-ROM/DVD-ROM as the first device in the "Boot priority order" by pressing the and <+> keys to move the CD-ROM/DVD-ROM to the top of the order. PhoenixBIOS Setup Utility Main Advanced Security Boot Exit Item Specific Help 4 Figure 4 - 2 BIOS Boot Menu Boot priority order: 1: IDE 0: TOSHIBA DVD-ROM SD-C26122: USB FDC Y-E DATA USB-FDU-(USB) 3: PCI SCSI: FT TX Ary 1 4: IDE 1: 5: 6: 7: 8: Excluded from boot order: : USB HDD : USB CDROM F1 Esc 7. 8.
Drivers & Utilities 13. Select the appropriate controller for your Windows XP operating system, and press Enter (see below). WinXP Promise SATA378 (tm) Controller Win2000 Promise SATA378(tm) Controller Figure 4 - 3 ATA Controller OS Select 4 14. The system will now read from the floppy disk drive and then return to the Windows Setup menu. 15. Press Enter to continue installing the operating system as normal (see your Windows documentation if you need help on installing the Windows OS).
Drivers & Utilities RAID Mode Configuration 4 If you wish to configure your hard disk(s) in RAID (Redundant Array of Independent Disks) mode, then see the instructions on the following pages. This will allow you to use your hard disks in combination with Striping (RAID 0) or Mirroring (RAID 1) for fault tolerance and performance. You will need an external floppy drive attached when installing the driver when setting up Windows.
Drivers & Utilities RAID Mode Setup 1. Install two identical hard disk drives (see the note below for Parallel ATA Hard Disks). Jumper Settings for Two Parallel ATA Hard Disks If you are using Parallel ATA (PATA) hard disk drives. then set the jumper on the Slave hard disk to the Cable Select option in order for the system to recognize the disks (see your hard disk manual or the information printed on the hard disk itself for details on the jumper settings).
Drivers & Utilities 2. 3. 4 4. 5. 6. Prepare a formatted blank 3.5" 1.44MB floppy diskette, and an external USB floppy disk drive. Create a RAID Driver Diskette by using an operable computer to copy the Drivers\RAID\FASTTRAK folder from the Device Drivers & Utilities + User’s Manual CD-ROM (Navigate/Browse.. to D:Drivers\RAID\FASTTRAK) to the blank floppy diskette. Connect the external USB floppy disk drive to the notebook computer.
Drivers & Utilities 7. Select the CD-ROM/DVD-ROM as the first device in the "Boot priority order" by pressing the and <+> keys to move the CD-ROM/DVD-ROM to the top of the order.
Drivers & Utilities 11. If a disk array is defined the screen will appear as follows (press the Ctrl + F key combination to enter the utility). Figure 4 - 8 4 FastTrak BIOS (Array Defined) FastTrak 378(tm) BIOS Version 1.00.1.35 (C) 2002-2005 Promise Technology, Inc. All rights reserved. ID MODE SIZE TRACK-MAPPING STATUS 1 1x2 Mirror 30000M 3647/255/63 Functional Press to enter FastBuild (tm) Utility...... 12.
Drivers & Utilities 13. Press <4> to enter the Delete Array Menu in order to delete existing arrays (press to return to the Main Menu). 14. Press <1> to enter the Auto Setup Menu (recommended) as this is the easiest and fastest way to setup your first array. Use to cycle through the “Optimize Array for” section for Performance (RAID 0, Stripe) or Security (RAID 1, Mirror) RAID mode, and then press + to save your selection. FastBuild (tm) Utility 2.
Drivers & Utilities FastBuild (tm) Utility 2.01 (c) 2002-2005 Promise Technology, Inc. [ Define Array Menu ] A Figure 4 - 11 4 FastBuild Utility (Define Array Menu) Array Array Array Array de 1 2 3 4 ---------- ---------- ---------- ---------- [ Keys Available ] [↑] Up [↓] Down [Esc] Exit [Enter] Select 17. After pressing to select the array the following menu will appear. FastBuild (tm) Utility 2.01 (c) 2002-2005 Promise Technology, Inc.
Drivers & Utilities Gigabyte Boundary The Gigabyte Boundary feature is designed for fault tolerant arrays RAID 1 (Mirror) in which a drive has failed, and the user cannot replace the drive with a drive of the same capacity or larger. This feature permits the installation of a replacement drive that is slightly smaller than any remaining working drive (e.g. a 20.50GB drive would be rounded down to 20GB). This can be useful if a drive fails and an exact replacement is no longer available.
Drivers & Utilities 4 19. Press a key when you see the message "Press any key to start up from the CD/Press any key to boot from CD". 20. Press the F6 key when you see the message “Press F6 if you need to install third party SCSI or RAID driver”. 21. When the Windows Setup menu appears, press the key to "Specify Additional Device". 22. Insert the RAID Driver Diskette into the external USB Floppy drive. 23.
Drivers & Utilities What to Install The Device Drivers & Utilities + User’s Manual CD-ROM contains the drivers and utilities necessary for the proper operation of the computer. The drivers for all the modules (WLAN, Bluetooth, PC Camera, TV Tuner and RAID) are on the separate CD-ROMs supplied. Table 4 - 2, on page 4 - 20 lists what you need to install manually according to your choice of the operating system, and it is very important that the drivers are installed in the order indicated.
Drivers & Utilities Navigate (Browse..) to D: 4 You will notice that many of the instructions for driver installation require you to “Navigate (Browse) to D:”. We assume that you will install all drivers and utilities from the built-in CD device and it is assigned to “Drive D:”. In addition, all file extensions can be seen In this case “D:” is the drive specified for your CD device. Not all computers are setup the same way, and some computers have the CD listed under a different drive letter - e.g.
Drivers & Utilities Service Packs Check the warnings on the following pages regarding installation of the appropriate Service Pack for your Windows OS. If you are unsure of the Service Pack currently installed see below. Make sure you have installed the appropriate Service Pack before installing all the drivers. Service Pack Installed To see which Service Pack is currently installed on your computer go to the General tab of the System control panel.
Drivers & Utilities Authorized Driver Message 4 If you receive a message telling you that the driver you are installing is not authorized (Digital Signature Not Found), just click Yes or Continue Anyway to ignore the message and continue the installation procedure. You will receive this message in cases where the driver has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual CD-ROM and the Notebook Driver Installation application will run automatically. If you want to install the driver manually see “Manual Driver Installation” on page 4 - 20. 1. 2. 3. 4. 5. 6. Check the driver installation order from Table 4 2, on page 4 - 20 (the drivers must be installed in this order) which is the same as that listed in the driver installation screen menu.
Drivers & Utilities Manual Driver Installation Windows XP (SP2) Windows XP Media Center Edition (SP2) 4 Feature Chipset page 4 - 21 Audio page 4 - 22 Modem page 4 - 22 Network (LAN) page 4 - 23 NVDIA - see page B - 1 ATI - see page C - 1 Video AP-Key Buttons page 4 - 23 TouchPad page 4 - 23 802.
Drivers & Utilities Windows XP This section covers driver and utility installation instructions for Windows XP (Professional & Home) and Windows XP Media Center Edition. Windows XP Service Pack 2 New Hardware Found If you see the message “New Hardware Found” (Found New Hardware Wizard) during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure.
Drivers & Utilities 4 Audio (WinXP) Modem (WinXP) 1. Double-click AUDIO from the Notebook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\AUDIO\Setup.exe and click OK. 2. Click Next (click Cancel if The Found New Hardware Wizard appears). 3. Click Finish to restart the computer. 4. When the computer restarts click Cancel if the The Found New Hardware Wizard appears (click Continue Anyway if asked if you want to continue at any time). 5.
Drivers & Utilities LAN (WinXP) AP-Key Buttons (WinXP) 1. Double-click LAN from the Notebook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\LAN\Setup.exe and click OK. 2. Click Next. 3. Click Finish. 4. The network settings can now be configured. 1. Double-click AP-KEY from the Notebook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\AP-Key\SETUP.exe and click OK. 2. Click Next. 3.
Drivers & Utilities 4 Module Drivers TV Tuner (WinXP) See the following pages for the driver installation procedures for any modules included in your purchase option. See the install procedure in “Installing the AverTV Utility Software” on page 7 - 10, “Installing the InterVideo WinDVD 4 Software” on page 7 - 10, or “Installing the MPC622 Driver for Windows XP Media Center Edition (MCE)” on page 7 - 11. Wireless LAN (WinXP) See the install procedure in “IPN2220 (802.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured is for guideline purposes only. The POST screen on your computer may appear slightly different. The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). As the POST proceeds, the computer will tell you if there is anything wrong.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non-fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen in Figure 5 - 1 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with five (5) menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu PhoenixBIOS Setup Utility Figure 5 - 2 Main Main Advanced Security Boot Exit Main Menu Item Specific Help System Time: 13 [22:11:05] [09/22/2004] System Date: , , or selects field.
BIOS Utilities IDE 0/1 Optical Device (Main Menu) Pressing Enter here opens the sub-menu to show the configuration of a CD/ DVD Device on the computer’s IDE Channels 0 or 1. Use the Auto (Type:) setting to have the items configured automatically for you. Installed memory (Main Menu) This item contains information on the system memory, and is not user configurable.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu PhoenixBIOS Setup Utility Advanced Advanced Main Security Power Boot Setup Warning Setting items on this menu to incorrect values may cause your system to malfunction.
BIOS Utilities I/O Device Configuration (Advanced Menu) The sub-menus under this item include options to configure the Serial port A (Serial Mouse), Serial port B (Infrared) and Parallel (Printer) port. These can be left to the default settings; however you may wish to use certain devices that require settings to be adjusted accordingly. Check the documentation for any such devices to see what settings are required. 5 Reset Configuration Data (Advanced Menu) This item is set to No as default.
BIOS Utilities Power On Beep (Advanced Menu) Use this menu to enable/disable the single beep sound at the end of the POST. This item is “Disabled” by default. Card Reader: (Advanced Menu) This option allows you to enable/disable support for the 10-in-1 Card Reader. and is “Enabled” by default. However if you are installing an operating system (e.g.
BIOS Utilities Security Menu Figure 5 - 4 PhoenixBIOS Setup Utility Main Advanced Security Security Boot Security Menu Exit Item Specific Help Supervisor Password Is: Clear Set Supervisor Password Enter] [E Password on boot: [Disabled] Supervisor Password controls access to the setup utility.
BIOS Utilities Password Warning 5 If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. 5 - 12 Security Menu Password on boot: (Security Menu) Specify whether or not a password (supervisor or user password) should be entered to boot the computer.
BIOS Utilities Boot Menu PhoenixBIOS Setup Utility Main Advanced Security Boot Figure 5 - 5 Exit Boot Menu Item Specific Help Boot priority order: 1: USB FDC: 2: IDE 0: 3: PCI SCSI: FT TX Ary 1 4: IDE 1: QSI CD-RW/DVD-ROM SBW242C 5: PCI LAN: 6: 7: 8: Excluded from boot order: : USB HDD: : USB CDROM: F1 Esc Help Exit Select Item Select Menu -/+ Enter Keys used to view or configure devices: Up and Down arrows select a device. <+> and <-> moves the device up or down.
BIOS Utilities Boot devices usually are hard drives, floppy drives, CD-ROM/DVD-ROMs and LANs (Local Area Networks). When you specify a device as a boot device on the Boot Menu, it requires the availability of an operating system on that device. Most home computers come with an operating system already installed on “Drive C:”. 5 If you wish to boot from a CD-ROM/DVD-ROM you will need to add it to the boot order. As a general rule the order below is recommended: 1. 2. 3. 4.
BIOS Utilities Exit Menu Figure 5 - 6 PhoenixBIOS Setup Utility Main Advanced Security Boot Exit Menu Exit Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Utilities 5 5 - 16
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. Turn the computer off, and turn it over. Loosen screws 1 - 3 . Release the battery, and lift the battery 4 out of the battery bay. 1 2 3 Warranty Warning Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CDROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 1. 2. 3. Turn off the computer, and turn it over and remove the battery. Locate the hard disk bay cover and remove screws 1 - 4 . Remove the bay cover 5 .
Upgrading The Computer 4. 5. 6. Release the cable 6 and lift the hard disk assembly 7 up out off the computer. Remove screws 8 - 15 in order to separate the bracket from the hard disk(s), and disconnect the cable 16 . Reverse the process to install a new hard disk(s).
Upgrading The Computer Upgrading the System Memory (RAM) The computer has four memory sockets for 200 pin Small Outline Dual Inline (SO-DIMM) - DDR-II (DDR2) - type memory modules (see “Memory” on page D - 2). The total memory size is automatically detected by the POST routine once you turn on your computer. 1. 2. Turn off the computer, and turn it over and remove the battery.
Upgrading The Computer 3. Gently pull the two release latches ( 6 & 7 ) on the sides of the memory socket in the direction indicated by the arrows in Figure 6 - 5. Figure 6 - 5 RAM Module Removal 6 7 8 8 6 6 4. 5. 6. 7 The RAM module 8 will pop-up, and you can remove it. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. 7. The module’s pin alignment will allow it to only fit one way.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device(s) 1. 2. 3. Turn off the computer, and turn it over and remove the battery. Locate the hard disk bay cover and remove screws 1 - 4 , and remove the bay cover. Remove screw 5 and use the screwdriver to push the optical device(s) out of the computer at point 6 .
Upgrading The Computer Warranty The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 6 Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
Modules Chapter 7: Modules Overview This chapter contains the information on the various modules (some of which are optional) which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
Modules Wireless Device Operation Aboard Aircraft 7 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. The Wireless LAN & Bluetooth Modules If your purchase option includes the any of the Wireless LAN modules and/or Bluetooth and Wireless LAN combination module, follow the information on the following pages for instructions on installing the driver.
Modules Mini-PCI Wireless LAN Module Before installing the Wireless LAN driver, make sure that the optional WLAN module is on (the LED will be green). Use the WLAN module key combination Fn + F11 to toggle power to the WLAN module. Make sure you install the drivers in the order indicated in Table 4 - 2, on page 4 - 20. You will be provided with the appropriate driver CD for your module. Insert the CD and follow the installation procedure.
Modules Network Connection 7 Use the Windows Network Connections control panel to access available wireless networks (Start > Settings > Network Connections / Network and Dial-up Connections or Start > Connect To > Show all Connections). IPN2220 (802.11g) Wireless LAN Driver Installation 1. 2. 3. 4. 5. 6. 7. Insert the Wireless LAN CD-ROM into the CD/DVD drive. Click Start (menu) > Run... Navigate (Browse..) to D:\setup.exe and click OK. Click Next.
Modules MP54G3 (802.11g) WLAN Module Driver Installation 1. 2. 3. 4. 5. 6. 7. Insert the WLAN CD-ROM into the CD/DVD drive. The program will run automatically. Click Install Software and click Next. Click the button to accept the license agreement, and then click Next. Click Install. Click Finish. Access any available wireless networks from Network Connections control panel in Windows (see sidebar).
Modules Wireless Device Operation Aboard Aircraft 7 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Bluetooth/WLAN Combo Module Before installing the Bluetooth/WLAN driver, make sure that the optional Bluetooth module/WLAN is on. Use the Bluetooth module key combination Fn + F12 to toggle power to the Bluetooth module.
Modules Combo Module Bluetooth Driver Installation 1. 2. 3. 4. 5. 6. 7. 8. 9. Insert the Bluetooth/WLAN Combo CD-ROM into the CD/DVD drive. The program will run automatically. Click Install Bluetooth Driver and click Next. Click the button to accept the license agreement, and then click Next. Click Next > Install (click OK/Continue Anyway if asked if you want to continue). When the Found New Hardware Wizard appears click the No, not this time button, and click Next.
Modules Network Connection 7 Use the Windows Network Connections control panel to access available wireless networks (Start > Settings > Network Connections / Network and Dial-up Connections or Start > Connect To > Show all Connections). Combo Module WLAN Driver Installation 1. 2. 3. 4. 5. 6. 7. Insert the Bluetooth/WLAN Combo CD-ROM into the CD/DVD drive. The program will run automatically. Click Install WLAN Driver and click Next.
Modules TV Tuner Module Options You may have one of two possible optional Mini-PCI TV Tuner modules supplied with your computer, depending on your purchase configuration. The optional TV Tuner allows you to watch TV, play music CDs, video conference and capture still images and video on your PC. The AverMedia M102 TV Tuner module comes with a remote control unit, and CDs containing the AverTV Utility software & InterVideo WinDVD 4 software.
Modules AverTV User Guide 7 Insert the AverTV Utility CD-ROM and click Acrobat Reader 5.1 (button) to install the program (if you have not already done so) to read the AVerTV User Guide. The guide is accessible from the Start > Programs/All Programs > AVer TV menu. AverMedia M102 Mini-PCI TV Tuner Module If your purchase includes the AverMedia M102 TV Tuner then you will need to install the driver and application software as per the instructions below. Installing the AverTV Utility Software 1.
Modules YUAN PVR Mini-PCI MPC622-MCE TV Tuner Module If your purchase includes the YUAN PVR MPC622 TV Tuner for Windows XP Media Center Edition, then you will need to install the driver as per the instructions below. In order to watch TV channels you will need to purchase a copy of Cyberlink Power DVD 5.0. Installing the MPC622 Driver for Windows XP Media Center Edition (MCE) 1. Insert the driver CD-ROM into the CD/DVD drive. 2. Click Start (menu) > Run... and navigate (Browse..) to D:\MPC622_WHQL.
Modules PC Camera & TV Tuner 7 If you have the optional TV Tuner included in your purchase, make sure you install the TV Tuner driver and application first. After installing the PC Camera driver you will need to select which device to use with the BisonCap program. Go to the Devices menu in the BisonCap program and select the BisonCam, USB2.0 device.
Modules PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. 5. 6. 7. Go to the Start menu and point to Settings (or click Control Panel) and click Control Panel, then double-click the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View). Click Advanced in the Device volume tab. Click Options and scroll down and click Properties.
Modules ( Figure 7 - 5 Audio Setup 7 7 - 14 PC Camera
Modules BisonCap BisonCap is a video viewer useful for general purpose video viewing and testing, and can capture video files to .avi format. 1. 2. 3. 4. 5. Run the BisonCap program from the Start > Programs/All Programs > Bs350u2 menu (it is recommended that you set the capture file before the capture process - see Set Capture File below). Go to the Capture menu heading and select Start Capture.
Modules Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the option from the Video Capture Filter options. 1. 2. 3. Figure 7 - 6 Video Capture Filter 7 7 - 16 PC Camera Run the BisonCap program. Go to Options and scroll down to select “Video Capture Filter...”. Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power Indicators (see “LED Indicators” on page 1 - 6) to see the computer’s power status. • Connections - Check all the cables to make sure that there are no loose connections anywhere.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Power Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The Battery LED power indicator , is blinking orange. Low Battery. Plug in the AC power source.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the vents/fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 9). Make sure you’re using the correct adapter.
Troubleshooting Display Problem Nothing screen. appears Possible Cause - Solution on The system is in a power saving mode. Toggle the sleep/resume key combination, Fn + F4 (see “Sleep Button” on page 3 - 8). \ The screen controls need to be adjusted. Toggle the screen control key combinations Fn + F8/F9 (see “Opening the LCD” on page 3 - 2). If you’re connected to an external monitor, make sure it’s plugged in and turned on. You should also check the monitor’s own brightness and contrast controls.
Troubleshooting Boot Password Problem You forget password. the Possible Cause - Solution boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning 8 If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Audio & CD Device Problem Possible Cause - Solution The sound cannot be heard or the volume is very low. The volume might be set too low. Check the volume control in the Volume Control Panel in the Windows taskbar, or use the key combination Fn + F5 and F6 (see “Audio Features” on page 2 - 10) to adjust. The compact disc cannot be read. The compact disc is dirty. Clean it with a CD-ROM cleaner kit. The compact disc tray will not open when there is a disc in the tray.
Troubleshooting Keyboard Problem Unwelcome numbers appear when typing. Possible Cause - Solution If the LED is lit, then Num Lock is turned ON (see “LED Indicators” on page 1 - 6). Other Keyboards 8 If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/AP-key buttons unique to the system’s regular keyboard may not work.
Troubleshooting Operation Problem Possible Cause - Solution The system freezes or the screen goes dark. The system’s power saving features have timed-out. Use the AC adapter, press a key on the keyboard, or press the sleep (Fn + F4) key combination, or press the power button if no LEDs are lit. The system never goes into a power saving mode. Power Options features are not enabled. Go to the Windows Power Options menu and enable the features you prefer (see “System Power Options” on page 3 - 6).
Troubleshooting Modules 8 Problem Possible Cause - Solution The Wireless LAN/ Bluetooth/ modules cannot be detected. The modules are off. Check the LED indicator to see if the modules are on or off (see “LED Indicators” on page 1 - 6). If the LED indicator is off, then press the appropriate AP-Key button in order to enable the modules (see Table 1 - 3 “- AP-Key Buttons” on page 1 - 7 The Wireless LAN/ Bluetooth/ modules cannot be configured. The driver(s) for the module(s) have not been installed.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the ports & jacks which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Ports and Jacks Item Built-In Microphone A A - 2 Description The built-in microphone allows you to record on your computer DC-In Jack Plug the supplied AC adapter into this jack to power your computer. Serial Port Connect a serial type mouse to this port. Parallel Port Connect a parallel type printer to this port. The port supports ECP (Extended Capabilities Port) and EPP (Enhanced Parallel Port) 1.7/1.9 modes.
Interface (Ports & Jacks) Item Description PS/2 Port Connect an external PS/2 type mouse or keyboard to this port. You can use a “Y” splitter if you want to attach both. RJ-11 Phone Jack This port connects to the built-in modem. You may plug the telephone line directly into this RJ-11 telephone connection. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Interface (Ports & Jacks) Item Microphone-In Jack Description Plug an external microphone in to this jack to record on your computer. Headphone-Out Jack Headphones or speakers may be connected through this jack. Note: Set your system’s volume to a reduced level before connecting to this jack. Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store.
Interface (Ports & Jacks) A A - 6
NVIDIA Video Driver Controls Appendix B: NVIDIA Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 14. Video Card Options NVIDIA Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 2, on page 4 - 20. 1. Double-click VIDEO from the Notebook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\VIDEO\NVIDIA2\setup.exe and click OK. 2.
NVIDIA Video Driver Controls Taskbar Icon Click the NVIDIA taskbar icon then click NVIDIA Display > Laptop Display to bring up the GeForce Go/Quadro FX control panel. B NVIDIA Display Properties More advanced video configuration options are provided in the NVIDIA Display Properties control panel tab. 1. 2. 3. 4. Open the Display Properties > Settings (see “Video Features” on page 1 - 14) control panel. Click Advanced (button). Click GeForce Go/Quadro FX (tab).
NVIDIA Video Driver Controls Additional Properties The items listed in the Additional Properties window allow you to configure your display(s). If the items do not display you can either click the Additional Properties button, or click the icon . Screenshots All screenshots in this chapter are from the GeForce Go 7900 GTX in the Windows XP OS. If you are using a different NVIDIA video card some screens in may appear slightly different. Figure B - 2 Click pin icon to push pin in to keep the menu open.
NVIDIA Video Driver Controls You may make changes to the Display Settings, Color Correction, Video Overlay, Resolutions, Refresh Rates and Screen Rotation by clicking the appropriate tab and adjusting the setting. Figure B - 3 Screen Examples Help Menus B Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu.
NVIDIA Video Driver Controls NVIDIA nView Desktop Manager The nView Desktop Manager allows quick access to control panels for features such as Desktop Management, Profiles, Hot Keys etc. The Control panel may be accessed as follows. 1. 2. Click Start, point to Settings and click Control Panel (or just click Control Panel). Double-click NVIDIA nView Desktop Manager (icon) - Click "Switch to Classic View" from the left of the menu if you are in Category View.
NVIDIA Video Driver Controls Display Wizard Use the Display Wizard/TV Wizard in the Desktop Management window to quickly setup and configure any attached displays (see Figure B - 4 on page B - 5). Display Devices Besides the built-in LCD, you can also use an external monitor/flat panel display or TV as your display device. The following are the display options: 1. 2. 3. 4. The built-in LCD. An external monitor connected to the DVI-Out Port (may require DVI to VGA converter).
NVIDIA Video Driver Controls Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the DVI-Out Port at the rear of the computer. 1. 2. 3. 4. 5. 6. Attach your external monitor to the DVI-Out Port (or TV to the S-Video-Out jack), and turn it on. Go to Additional Properties in the GeForce Go/Quadro FX Properties control panel tab (see “NVIDIA Display Properties” on page B - 2). Select nView Display Settings. Select the display mode from the nView Display Mode drop box.
NVIDIA Video Driver Controls 7. Select the display option from the Primary Display/ Secondary Display dropbox. If you have a TV and external monitor/flat panel display attached you will have a number of available options (see sidebar). Select and Apply the appropriate option. 8. Click the monitor icon to select it, and then click Device Settings (button) to make any adjustments for the selected display (including Screen Resolutions & Refresh Rates). Click Apply to confirm any setting changes.
NVIDIA Video Driver Controls Display Modes Single Display Mode Only one of your displays is used. Clone Mode Clone Mode simply shows an exact copy of the Primary display desktop on the other display(s). This mode will drive multiple displays with the same content and each display device can be configured independently. Dualview Mode Dualview Mode treats both connected displays as separate devices, and they act as a virtual desktop resulting in a large workspace.
NVIDIA Video Driver Controls Detect Displays To get a full range of options from the Device Settings menu click the Detect Displays button. Click to select the TV icon, then click the Device Settings button. B Enabling TV Display To display desktop images on a TV, connect the TV to your computer by using an S-Video cable from the TV to the S-Video-Out jack on the left side of the computer (see “System Map: Left View” on page 1 - 10).
NVIDIA Video Driver Controls Set the TV format from the Select TV Format menu. The Advanced option at the bottom of the Select TV Format menu allows you to select TV format by country if you are unsure of your TV format. Figure B - 4 TV Settings and Adjustments B Device Adjustments (Device Settings menu) allows you to make changes to the TV output.
NVIDIA Video Driver Controls B B - 12
ATI Video Driver Controls Appendix C: ATI Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 14. ATI Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 2, on page 4 - 20. 1. Double-click VIDEO from the Notebook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\VIDEO\ATI\Setup.exe and click OK. 2.
ATI Video Driver Controls ATI Taskbar Icon You can also access ATI Mobility Radeon Properties by rightclicking the ATI icon in the taskbar. Point to Settings and click ATI Display Settings, then click the Settings (tab). ATI Mobility Radeon Properties More advanced video configuration options are provided in the ATI Mobility Radeon control panel tab: 1. 2. 3. 4. Open the Display Properties (see “Video Features” on page 1 - 14) control panel. Click Advanced (button).
ATI Video Driver Controls Help Menus Right-click on almost any item in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu. Help Menu Click to Configure Theater Mode (Not Supported with TV Tuner) Theater Mode Theater Mode is not supported with the TV Tuner module installed (see page C - 4).
ATI Video Driver Controls Theater Mode Theater Mode can be enabled by clicking Clone Mode Options (button) in the Overlay tab from the ATI Mobility Radeon Properties. (see page C - 3). Theater Mode enables you to display video playback in full screen on a secondary monitor. Theater Mode is not supported if you have the TV Tuner module installed. C C - 4 Display Devices Display Devices Besides the built-in LCD, you can also use an external monitor/flat panel display or TV/HDTV as your display device.
ATI Video Driver Controls Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the DVI-Out Port at the rear of the computer. 1. 2. 3. 4. 5. Attach your external monitor to the DVI-Out port (or TV/HDTV to the SVideo Out port), and turn it on. Select the Displays tab in the ATI Mobility Radeon properties. Click the enable/disable button / for the display device you wish to use. Click Apply. Click Yes to accept the settings and OK to save the changes.
ATI Video Driver Controls Primary & Clone Displays The Primary display in an Extended Desktop environment will be associated with display Icon 1 in the settings tab. The Clone display will set the associated display to show a copy of the Primary desktop. The Clone display in an Extended Desktop environment will show the portion of the desktop extended from the Primary display. C C - 6 Display Modes Display Modes Single Only one of your displays is used.
ATI Video Driver Controls Clone Mode Clone Mode simply shows an exact copy of the Primary display desktop on the other display(s). This mode will drive multiple displays with the same content. Use this feature to display the screen through a projector for a presentation. Each display device can be configured independently as this allows you to set the options for overhead projectors etc., which require specific resolutions and refresh rates.
ATI Video Driver Controls Extended Desktop Mode The system supports Extended Desktop in multiple display environments in Windows XP. An Extended Desktop creates a desktop spanning multiple displays and acts as a large workspace. To get this effect: 1. 2. 3. 4. 5. 6. 7. 8. 9. C C - 8 Display Modes Attach your external monitor to the DVI-Out port (or TV/HDTV to the SVideo Out port), and turn it on. Select the Displays tab in the ATI Mobility Radeon properties.
ATI Video Driver Controls 10. In the example shown in Figure C - 5 the primary monitor 1 is on the left, the other display is on the right. Help Click either the Display pop-up menu, or click the icon for the appropriate display. Then click the tick box to extend the primary display’s desktop to it. Further help is available through the menus accessed from the taskbar (see Figure C - 1 on page C 2). Figure C - 5 Extended Desktop Monitor Arrangement 11.
ATI Video Driver Controls 12. One display will be set to 1 (Primary). The displays may be switched as long as one as set to Primary. Figure C - 6 Displays Tab (Extended Desktop Mode) In this picture the notebook LCD panel is the primary display, and the desktop may be extended to any attached displays. The primary display is indicated with a button depressed. Click the buttons to switch the primary display. 13.
ATI Video Driver Controls Enabling TV Display To display desktop images on a TV, connect the TV to your computer by using an S-Video cable from the TV to the S-Video-Out jack on the left side of the computer (see “System Map: Left View” on page 1 - 10). Further help is available to help you troubleshoot your TV connection through the menus accessed from the taskbar (see page Figure C - 1 on page C - 2).
ATI Video Driver Controls C C - 12
Specifications Appendix D: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your service center for details.
Specifications Feature Specification Core Logic Intel 915P + ICH6 Security Security (Kensington® Type) Lock Slot Memory Two 64-bit wide DDR-II (DDR2) Data Channels Four 200 Pin DDR-II (DD2) SODIMM Sockets Expandable up to 4GB (Compatible with 1024MB, 512MB, 256MB DDR-II (DDR2) - 400/ 533 Modules) BIOS Password Memory Available Even if you have 4GB of RAM in the computer, the POST (at Startup) or System (Windows) Control Panel, will show 2814GB of RAM available to the system.
Specifications Feature Video Card Options Video Card Options Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported. Specification NVIDIA GeForce Go 7900-GTX High Performance Graphic Chip 256MB GDDRIII (GDDR3) Video RAM On Board 256 bit Memory Interface PCI Express * 16 Fully Supports DirectX® 9 H.
Specifications Feature Storage Options Specification One External USB 1.44Mb Floppy Disk Drive One Changeable Primary 2.5" 9.5mm (h) Hard Disk Drive One Changeable Secondary 2.5" 9.5mm (h) Hard Disk Drive Option) Supports Serial/Parallel ATA HDDs RAID 0, RAID 1, HDD Fault Tolerance System One Changeable Primary Optical Device Bay - 12.7 mm (h) for Optical CD/DVD Device Drive Options (see “Optional” on page D - 7) One Changeable Secondary Optical Device Bay - 12.
Specifications Feature Specification I/O Ports Four USB 2.0/1.1 Ports Two Mini-IEEE1394a Ports One S-Video-Out Jack for TV & HDTV Output One Serial Port One Parallel Port (LPT1) Supporting ECP/EPP One Infrared Transceiver (IrDA 1.
Specifications Feature Specification Power Management Supports ACPI 2.0 Supports Hibernate/Standby Modes Supports Battery Low Sleep Supports Resume from Alarm Supports Resume from Modem Ring Power Full Range 220W AC adapter – AC in 100~240V, 47~63Hz DC Output 20V, 11 A Easy Changeable 12-Cell Smart Lithium-Ion 6600mAH Main Battery Environmental Spec Temperature Operating: Non-Operating: Physical Dimensions & Weight 397mm (w) * 298mm (d) * 49.
Specifications Feature Optional Specification Software DVD Player DVD/CD-RW Combo Drive Module DVD-Dual Drive Module 300K Pixel Video Camera Module (Optional) 1.3M Pixel Video Camera Module (Optional) Mini-PCI TV Tuner Module Options: AverMedia M102 Mini-PCI TV Tuner OR YUAN PVR Mini-PCI MPC622-MCE TV Tuner (for Windows Media Center Edition) WLAN/Bluetooth Module Options: Mini-PCI 802.11 b/g Wireless LAN Module OR Mini-PCI 802.
Specifications D D- 8
