Euphonix System System 5 Post and Film Setup Guide Document Revision: 1.2 Release Date: January 2006 Euphonix Inc. 220 Portage Ave. Palo Alto, California 94306 Phone: 650-855-0400 Fax: 650-855-0410 Web: http://www.euphonix.com e-mail: info@euphonix.
In the interest of continued product development, Euphonix reserves the right to make improvements in this manual and the product it describes at any time, without notice or obligation. System 5, S-5, PatchNet, eMix, EuCon, R-1, Audio Deck, Studio Hub are trademarks of Euphonix Inc. ©2006 Euphonix, Inc. All rights reserved worldwide.
Euphonix System 5 Post and Film Setup Guide Table of Contents CM403 Installation ..........................................................................................................................5 CM403 Module..............................................................................................................5 External Record Control ................................................................................................6 Film Panel Installation ....................................
Euphonix System 5 Post and Film Setup Guide CM403 Installation CM403 Module The CM403 uses the same form factor and architecture as a standard control module (CM401, 402, 408). A single Ethernet port connects the module to the system via the 100 BaseT EuCon switch. The CM403 houses a TFT and fits three panels of the same size: Film Post and the Dual-Joystick Panels. The Film Post panel can be placed above or below the Joystick Panel depending on the preference of the operator.
Euphonix System 5 Post and Film Setup Guide ID selection Up to four CM403 modules can be installed in a System 5 console. Set the ID switches on the back panel of the module according to Table 1: Table 1 CM403 ID Switch Settings CM403 # Frame ID Module ID Position # in eMix 1 1H 13 1–29 2 1H 14 1–30 3 1H 15 1–31 4 1H 16 1–32 NOTE: In a dual-operator console, all CM403 modules are connected to the master console, which is used for monitoring and record control.
Euphonix System 5 Post and Film Setup Guide Film Panel Installation NOTE: Each instruction pertains to the picture beneath its text. Connect the 5-V power cables (red) from the Film Panel to the header block on the bottom of the module. Be sure to maintain correct polarity (red/white stripe is negative). Connect the 12-V power connection to the mating connector coming from the PSU. Connect the PC104 cable to H26 on the Film Panels 386 board.
Euphonix System 5 Post and Film Setup Guide Connect the opposite end of the PC104 cable to the PC104 card on the SBC (Single Board Computer) mounted on the rear ventilation panel of the module. Secure the RF choke as shown above. Connect the Euphonix Ext cable (25-pin D-sub on the rear panel) to H103 on the upper board of the Film Panel.
Euphonix System 5 Post and Film Setup Guide Connect the TFT backlight cable to the connector on the upper board of the film panel. Joystick Panel Installation Connect the 5-V power cables (red) from the Joystick to the header block on the bottom of the module. Be sure to maintain correct polarity (red/white stripe is negative). See the photo in Film Panel Installation. Connect the serial cables from the 9-pin connectors on the rear panel of the CM403 to the headers on the joystick PCBs.
Euphonix System 5 Post and Film Setup Guide Blank Panel .480 X2 .285 .437 11.00 X2 1.150 .625 10.960 1.800 FREE SPACE 6.700 8.200 2.300 .500 .500 .875 11.960 1.800 .
Euphonix System 5 Post and Film Setup Guide Record Control Setup Version 2.5 of eMix added record and track-arming functionality to the System 5 console. Version 3.0x (or higher) of the TT007 software is required. One record machine with up to 48 tracks is supported; additional record machines can be supported using third-party hardware. Contact Euphonix customer support for more information. Perform the following steps to enable record- and track-arming: 1.
Euphonix System 5 Post and Film Setup Guide Solo Linking NOTE: Problems may occur if the Solo Linking service is running when eMix is installed. To avoid this, open the MOConfig.exe application and click Stop to stop the service before installing newer software. Physical Connection Between Systems In a two-operator system, a single Cat5 cross-over cable connects the two system PCs using the spare network adaptor ports.
Euphonix System 5 Post and Film Setup Guide Network Settings The settings for the network identification and addressing are found in the Network Connections window. Open the Network Connections window by choosing Settings->Network Connections from the Start menu. Change the Computer Name In the Network Connections window, select Network Identification from the Advanced menu. Figure 3 Network Connections Window with Advanced Menu The System Properties dialog opens with the Computer Name tab selected.
Euphonix System 5 Post and Film Setup Guide Figure 4 Computer Name tab 1. Click the Change button at the bottom-right. A dialog appears requesting the new name. 2. Type one the following names depending on the console being changed: Master - S5M Slave1 - S5S1 Slave2 - S5S2 3. Do not change the domain and workgroup settings; consult your network administrator for the proper settings for your network. 4. Click OK on the renaming dialog. A dialog appears warning that a restart is needed. 5.
Euphonix System 5 Post and Film Setup Guide Assign IP Address to Second Network Interface Card Two network connections are displayed in the Network Connections window. One is for your console’s modules and pilots (typically named EuCon) the other for the connection to your outside LAN. 1. Right-click on the LAN connection (NOT the EuCon connection) and choose Properties. The Studio LAN Properties dialog opens. Figure 5 Studio LAN Properties dialog 2.
Euphonix System 5 Post and Film Setup Guide Figure 6 Internet Protocol (TCP/IP) Properties dialog 3. Click the Use The Following IP Address radio button and enter the IP address according to the following: Master - 10.0.0.1 Slave1 - 10.0.0.2 Slave2 - 10.0.0.3 The subnet mask is 255.255.255.0 for all three systems. Leave the Default Gateway and DNS Server fields blank. 4. Click OK to close the Internet Protocol Properties. 5. Click on the Advanced tab at the top of the connection properties dialog.
Euphonix System 5 Post and Film Setup Guide Figure 7 Advanced tab of Studio LAN Properties dialog 6. Press OK to close the connection properties dialog.
Euphonix System 5 Post and Film Setup Guide Configure DCOM Using Component Services Editor 1. After restarting the computer, open the Component Services Editor. 2. Click Start and select Run. The Run dialog appears. 3. Type dcomcnfg and press Enter. The Component Services Editor appears. Figure 8 Component Services Editor 4. Expand Component Services in the left pane (Figure 8). 5. Right-click on My Computer and choose Properties. The My Computer Properties dialog opens. 6.
Euphonix System 5 Post and Film Setup Guide Figure 9 My Computer Properties-Default Properties tab 7. Make sure Enable Distributed COM on this computer is checked, Default Authentication Level is set to None, and Default Impersonation Level is set to Impersonate. 8. Then click Apply. (Do not click OK or you will close the System Properties dialog). 9. Now click the COM Security tab.
Euphonix System 5 Post and Film Setup Guide Figure 10 My Computer Properties-COM Security tab The tab has Edit Limits and Edit Defaults buttons for Access Permissions and Launch & Activation Permissions. Each button opens a permissions setting dialog. 10. Click the Edit Limits and Edit Permissions buttons in turn. In each permissions dialog, select each user shown and click Allow for each permission.
Euphonix System 5 Post and Film Setup Guide Figure 11 Launch Permissions dialog example 11. When finished, click Apply in the My Computer Properties dialog and the OK to close it. 12. Back in the Component Services Editor window, expand My Computer, then expand DCOM Config as shown below.
Euphonix System 5 Post and Film Setup Guide Figure 12 Component Services-S5MultiServer 22
Euphonix System 5 Post and Film Setup Guide 13. Right-click on S5MultiServer, then choose Properties. The S5MultiServer Properties dialog opens. Figure 13 S5MultiServer Properties-General tab 14. In the General tab, make sure that Authentication Level is set to Default. 15. Click Apply. Do NOT click OK or you will close the dialog.
Euphonix System 5 Post and Film Setup Guide 16. Click the Location tab. Figure 14 Location Dialog - Run on this computer. 17. On the Master console (S5M -10.0.0.1), select Run application on this computer. Figure 15 Location Dialog - Run on another computer. 18. On all Slave consoles perform the following procedure: a. Select Run application on the following computer. b. Click the Browse button. The Select Computer dialog opens.
Euphonix System 5 Post and Film Setup Guide Figure 16 Select Computer dialog c. Click the Advanced button (bottom left). The Select Computer dialog expands to the advanced search mode. d. Click Find Now at the mid-right of the dialog. All the computers available on the network appear.
Euphonix System 5 Post and Film Setup Guide Figure 17 Select Computer-Advanced tab dialog e. Select S5M and then click OK to close the Advanced dialog. S5M should now appear in the Select Computer dialog. f. Click OK to close that dialog. 19. Click Apply to retain the changes. 20. Click the Security tab.
Euphonix System 5 Post and Film Setup Guide Figure 18 S5MultiServer Properties-Security tab 21. Make sure all three Use Default radio buttons are selected. 22. Click Apply then OK to close the S5MultiServer Properties dialog.
Euphonix System 5 Post and Film Setup Guide Setting up MOConfig 1. Open up a Windows Explorer window and locate the C:\emix directory. 2. Double-click MOConfig.exe to display the following dialog: Figure 19 Multi-Operator Configuration Dialog 3. Click the Enable Multi Operator checkbox. 4. Enter 10.0.0.1 for the Master Console System PC Address. Bus Cascade Inputs There are MADI ports on the front of the last (highest numbered) DF64 that are dedicated to Bus Cascade Inputs from a slave console.
Film Panel Figure 20 Dual Operator System Block Diagram 29 Slave Console Slave Console Network Film Panel Bus Cascade TT007 Machine Control MADI Master Console Master Console Third-Party Machine Control/Syncronizer (Soundmaster, JSK) Film Panel Monitor Controller Converter Converters Converters Main Monitors Audio Sources and Recorders Euphonix System 5 Post and Film Setup Guide Block Diagram
