Euphonix Modular I/O Configuration Guide Document Revision: 2.0 Release Date: April 2008 Euphonix, Inc. 220 Portage Ave. Palo Alto, California 94306 USA Phone: +1-650-855-0400 Fax: +1-650-855-0410 Web: www.euphonix.com email: info@euphonix.
Euphonix Modular I/O Configuration Guide In the interest of continued product development, Euphonix reserves the right to make improvements in this manual and the product it describes at any time, without notice or obligation. System 5, S-5, PatchNet, eMix, EuCon, R-1, Audio Deck, Studio Hub are trademarks of Euphonix Inc. ©2007 Euphonix, Inc. All rights reserved worldwide.
Euphonix Modular I/O Configuration Guide IMPORTANT SAFETY INSTRUCTIONS The lighting flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons.
Euphonix Modular I/O Configuration Guide Table of Contents Table of Contents Chapter 1: Product Description .……………….……..……… 9 1.1 Modular I/O Frame ………………………………………………………..9 1.1.1 IO93 Modular Frame .………….….………….………….……10 1.1.2 IO94 Stagebox Frame .………….………...…………..………11 1.1.3 IO95 Modular Frame ……………………………………….....11 1.2 MADI, Control, and Sync Modules ……………………………..………12 1.2.1 1.2.2 1.2.3 1.2.4 1.2.5 1.2.6 1.2.7 MM934/MM934opt MADI In/Out ……………………..………12 MM935 MADI In/Out …………………………………..
Euphonix Modular I/O Configuration Guide 2.1.1 2.1.2 2.1.3 2.1.4 Table of Contents IO93 Modular Frame w/ Linked Audio Busses …….....….…23 IO93 Modular Frame w/ Discrete Audio Busses ………...…24 IO94 Stagebox …………………………………………………25 IO95 Modular Frame as Local-Side MADI-over-Fiber Interface …………..……………………………………….…...26 2.2 Sample Configurations …………………………………………….……27 2.2.1 2.2.2 2.2.3 2.2.4 Sample Configuration 1 …………………….….……………27 Sample Configuration 2 ………….……………….…………28 Sample Configuration 3 ………………………….
Euphonix Modular I/O Configuration Guide Table of Contents AD920 4ch Analog Line Input ……………………..…………………………73 DA921 4ch Analog Line Output ……………………………………….…….75 AD922 4ch Analog Line Input ……………………..…………………………77 DA923 4ch Analog Line Output ……………………………………….…….79 AD924 4ch Mic Input …………………………………………………….……81 DD908 4ch AES I/O (110Ω) ………………….………………………….…..83 DD909 8ch AES Input (110Ω) ……...……………….…………………..…..85 DD910 8ch AES Out (110Ω) …..…….………..……..………….……….…..87 DD911 4ch AES I/O (75Ω) ……………………..……………….
Euphonix Modular I/O Configuration Guide Table of Contents List of Figures 2-1: IO93 Modular Frame w/ Linked Audio Busses ………………………….…23 2-2: IO93 Modular Frame w/ Discrete Audio Busses ………………………...…24 2-3: IO94 Stagebox …………………………………………………………………25 2-4: IO95 Modular Frame as Local-Side MADI-over-Fiber Interface …………...26 2-5: Sample Configuration 1……………………………………………………….27 2-6: Sample Configuration 2………………………….……………………………28 2-7: Sample Configuration 3………………………….
Euphonix Modular I/O Configuration Guide Product Description Chapter 1: Product Description Euphonix Modular I/O is designed to add a new level of flexibility in I/O configuration to the Euphonix range of audio converters. The Modular I/O system offers several types of frames that can be fitted with a variety of I/O modules. This allows frames to be customized to exactly meet client requirements. For interface to the console, all signals are converted to MADI.
Euphonix Modular I/O Configuration Guide Product Description Each audio backplane contains 32 passive stereo audio busses (64 total signal paths). Audio source and destination modules are connected to audio busses via physical on-board jumpers or via web-browser interface. Any audio buss may have multiple destinations but only a single source. Different frames have options to isolate audio busses in certain physical slot positions. This enables higher signal densities.
Euphonix Modular I/O Configuration Guide Product Description (configurable via DIP switched, some disassembly required to access). Connections, Power, Space, Weight Power (IEEEx2); PSU: autosensing (100~240vAC, 50/60Hz); input current (internal 5vDC rail at maximum load): 1.5A @ 99vAC, 700mA @ 207vAC; output: 5v@12A usable power, 3RU, front-plane module space: 72HP, rear-plane space: 76HP (typical module width: 4HP/8HP), audio connections will appear on front and rear in typical configurations.
Euphonix Modular I/O Configuration Guide Product Description For use as a local-side interface for redundant MADI-overFiber, four rear-plane “positions” of 3-slots each are audio isolated from the rest of the frame. These positions are as follows: slots 8-10, slots 11-13, slots 14-16, and slots17-19. Modules placed in these positions share the frames sync and control busses.
Euphonix Modular I/O Configuration Guide • • Product Description <56 out> <64 out> 96k Operation: In frames operating at 96k sample rate, only the first 28 signals in a MADI stream are available. In these cases, <32 in, 32 out> working mode yields the best signal efficiency with 28 MADI inputs and 28 MADI outputs at 96k. Note: When used as the master sync source, the MM934/MM934opt MADI In/Out should only be removed from a frame after the frame has been powered down.
Euphonix Modular I/O Configuration Guide Product Description General Description The MM936 contains a single MADI I/O connected via two multi-mode fiber transceivers for redundant MADI-over-Fiber operation. The module is typically placed in an IO94 Stagebox frame and interfaces to the console via a MM936 and MM934 pair placed in an IO95 local-side interface frame. The module features a master sync mode that allows it to lock a frame to its MADI input.
Euphonix Modular I/O Configuration Guide Product Description Sync in (BNC), Word Clock out (BNC), ~300 mA, 4HP, ~200g. 1.2.5 SY983 Sync General Description The SY983 contains an internal clock and can lock to external AES Sync, Word Clock, Video signal, or Tri-Level Sync. Internal sample rates are 44.1k, 48k, 88.2k, and 96k. The module features a sync redundancy mode which allows two modules, designated master and slave, to be fitted into a rack.
Euphonix Modular I/O Configuration Guide Product Description TCP/IP (RJ45), CAN Remote (RJ45) no longer used, RS232 (9pin DSub) for ip address configuration, ~300 mA, 4HP, ~200g. 1.2.7 WC984 4ch WCLK Out General Description The WC984 provides four workclock outputs derived from the frame’s sync buss, regardless of the module being used as the master sync source. Sample rates from 44.1k ~ 96k are supported. This module is highly recommended from frames where sync-to-MADI is being used as the sync method.
Euphonix Modular I/O Configuration Guide Product Description Connections, Power Consumption, Width, Weight Analog input (FXLR x4), ~850mA, 8HP, ~200g. 1.3.3 DA921 4ch Analog Line Output General Description The DA921 provides 4 analog outputs with 24 bit resolution and sample rates up to 96k. All settings are done with onboard switches including buss linking and analog reference level. Connections, Power Consumption, Width, Weight Analog output (MXLR x4), ~650mA, 8HP, ~200g. 1.3.
Euphonix Modular I/O Configuration Guide Product Description General Description The AD924 provides 4 remote controlled preamps with 24 bit resolution and sample rates up to 96k. Preamps are controlled via Eucon interface or web browser interface via the TCP/IP network on the FC972 Remote. On-board switches are used to link the sources to the frame’s audio busses and to set the device ID. Connections, Power Consumption, Width, Weight Analog input (MXLR x4), ~1100mA, 8HP, ~300g. 1.3.
Euphonix Modular I/O Configuration Guide Product Description Connections, Power Consumption, Width, Weight AES/EBU output (MXLR x4), ~100mA, 8HP, ~200g. 1.3.10 DD911 4ch AES I/O (75Ω) General Description The DD911 provides 4 AES inputs (2 pairs) with SRC and 4 AES outputs (2 pairs) with 75Ω connection. Buss link settings are done with on-board switches. Connections, Power Consumption, Width, Weight AES/EBU input (BNC x2), AES/EBU output (BNC x2), ~100mA, 4HP, ~150g. 1.3.
Euphonix Modular I/O Configuration Guide Product Description The DD901 provides decoding of Dolby E and Dolby digital signals. Access to metadata parameters is via web-browser interface (FC972 Remote required). Certain settings are done from on-board switches such as device ID. Connections, Power Consumption, Width, Weight Dolby D/E input (BNC), Metadata out (9-pin DSub), 4HP. 1.3.14 DE911 Dolby E Encoder General Description The DD911 provides encoding of a Dolby E signal.
Euphonix Modular I/O Configuration Guide Product Description module is capable of terminal-gear type functionality such as audio replacement, typically when used as an audio console interface it will function as either an embedder or deembedder. All settings are done using on-board switches. Connections, Power Consumption, Width, Weight SD out (BNC), SD in (BNC), SD through (BNC), ~800mA, 4HP, ~300g. 1.3.
Euphonix Modular I/O Configuration Guide Product Description Although the module is capable of terminal-gear type functionality such as audio replacement, typically when used as an audio console interface it will function as either an embedder or de-embedder. Additional features include 8 channel of audio delay, and a video test pattern generator.
Euphonix Modular I/O Configuration Guide Configuration Chapter 2: Configuration In this chapter, starting-point and sample configurations are illustrated. Several reference spreadsheets are also provided. 2.1 Starting Point Configurations 2.1.1 IO93 Modular Frame w/ Linked Audio Busses • • • • 64 total source signals I/O modules may be placed in either plane Single SY983 module shown as sync source FC972 Remote shown. If required, fit in any slot.
Euphonix Modular I/O Configuration Guide Configuration 2.1.2 IO93 Modular Frame w/ Discrete Audio Busses • • • • • 64 total signals per backplane I/O modules must be fitted on the same plane as their associated MADI module Two MADI I/O entry/exit Single SY983 module shown as sync source FC972 Remote shown. Fit if required on either backplane.
Euphonix Modular I/O Configuration Guide Configuration 2.1.3 IO94 Stagebox Frame • 64 total source signals MM936 MADI I/O (redundant MADI-over-Fiber) module shown as sync source (sync-to-MADI).
Euphonix Modular I/O Configuration Guide Configuration 2.1.4 IO95 Modular Frame as Local-Side MADI-over-Fiber Interface • • • • Four positions for local-side redundant MADI-over-Fiber interface modules Remaining slots may used for local I/O with front and rear planes linked or discrete.
Euphonix Modular I/O Configuration Guide Configuration 2.2 Sample Configurations 2.2.
Euphonix Modular I/O Configuration Guide Configuration 2.2.2 Sample Configuration 2: IO93 Modular Frame w/Discrete Audio Busses • • • • • • Single SY983 Sync module as sync source MADI working modes: Rear-plane MM934 set as <64 out> = 64 audio inputs.
Euphonix Modular I/O Configuration Guide Configuration 2.2.3 Sample Configuration 3: IO94 Stagebox Frame • • • • MM936 MADI I/O set to “sync-to-MADI” MADI config set using flexible crosspoint matrix via webbrowser interface 56 mic inputs 8 analog line outputs Single MADI I/O entry/exit FC972 Remote not required for remote preamp control and MM936 MADI configuration.
Euphonix Modular I/O Configuration Guide Configuration 2.2.4 Sample Configuration 4: IO95 Modular Frame as Local-Side Redundant MADI-over-Fiber Interface • • • • • • Single SY983 Sync module as sync source MM936/MM935 MADI pairs fit to interface to four redundant MADI-over-Fiber stageboxes FC972 Remote required to configure MM936 MADI Additional slots used as local I/O (single MADI entry/exit via MM934 fit into rear-plane slot 1).
Euphonix Modular I/O Configuration Guide Configuration 2.3 Summary Reference Spreadsheets The following summary spreadsheets are provided: • • • • • Summery of Frames Summary of Sync Modules Summery of MADI Module Summary of I/O Modules Cross-reference Between MM934 MADI I/O and Audio Busses 2.3.
Euphonix Modular I/O Configuration Guide Configuration 2.3.
Euphonix Modular I/O Configuration Guide Configuration 2.3.
Euphonix Modular I/O Configuration Guide Configuration 2.3.
Euphonix Modular I/O Configuration Guide Product Data Sheets Chapter 3: Product Data Sheets In this chapter, the following Product Data Sheets are provided: • • • • • • • • • • • • • • • • • • • • • • • • • • • • IO93 Modular I/O Frame IO94 Modular I/O Stagebox Frame IO95 Modular I/O Frame (for local-side redundant MADI-over-fiber interface) MM934/MM934opt MADI In/Out MM935 MADI In/Out MM936 MADI In/Out SY982 Sync (discontinued) SY983 Sync FC972 Remote WC984 4ch WCLK Out AD914 4ch Microphone Input AD920
Euphonix Modular I/O Configuration Guide Product Data Sheets 1/3 IO93 Modular Frame Features 19" modular chassis, 3RU, RF shielded • incl. 2 power supplies PS993 in redundant mode • incl. 1 double appliance socket with mains filter and switch • dual plane-card installation from both sides • external dimensions in accordance with DIN 41494, 320mm depth • aluminum side panels chromated, aluminum cross extrusions, RF protection by 0.
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/3 IO93 Modular Frame Technical Specifications frame size depth: rack space front-plane space for modules: rear-plane space for modules: weight: 420mm 3RU 72HP (18 single-width slots) 76HP (19 single-width slots) ~5.
Euphonix Modular I/O Configuration Guide Product Data Sheets 3/3 IO93 Modular Frame Installation Audio buss linking interconnect PCB w/32 DIP switches (some disassembly required to access) Four red “reserved” slots for master sync source modules (may be used for other modules as well) 38
Euphonix Modular I/O Configuration Guide Product Data Sheets IO94 Stagebox Frame Features 19" modular chassis, 3RU, RF shielded • incl. 2 built-in, power supplies in redundant mode • incl. 1 double appliance socket with mains filter and switch • single plane-card installation from both sides • external dimensions in accordance with DIN 41494, 320mm depth • aluminum side panels chromated, aluminum cross extrusions, RF protection by 0.
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/3 IO94 Stagebox Frame Technical Specifications frame size depth: rack space rear-plane space for modules: weight: 300mm 3RU 76HP (19 single-width slots) ~5.
Euphonix Modular I/O Configuration Guide Product Data Sheets IO94 Stagebox Frame Installation front-view rear-view Four red “reserved” slots for master sync source modules (may be used for other modules as well) 41 3/3
Euphonix Modular I/O Configuration Guide Product Data Sheets 1/4 IO95 Modular Frame Features 19" modular chassis, 3RU, RF shielded • incl. 2 power supplies PS993 in redundant mode • incl. 1 double appliance socket with mains filter and switch • dual plane-card installation from both sides • external dimensions in accordance with DIN 41494, 320mm depth • aluminum side panels chromated, aluminum cross extrusions, RF protection by 0.
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/4 IO95 Modular Frame Technical Specifications frame size depth: rack space front-plane space for modules: rear-plane space for modules: weight: 420mm 3RU 72HP (18 single-width slots) 76HP (19 single-width slots. 12 of these slots are audio isolated to provide four positions for local-side redundant MADIover-Fiber interface) ~5.
Euphonix Modular I/O Configuration Guide Product Data Sheets 3/4 IO95 Modular Frame Installation Audio buss separations allow four audio-isolated “positions” for localside redundant MADI-over-Fiber interface Audio buss linking interconnect PCB w/32 DIP switches (some disassembly required to access) Four red “reserved” slots for master sync source modules (may be used for other modules as well) 44
Euphonix Modular I/O Configuration Guide Product Data Sheets IO95 Modular I/O Frame 4/4 Local-side Redundant MADI-over-Fiber Interface The IO95 frame provides four “positions” for local-side interface to redundant MADI-over-Fiber stageboxes. Audio busses in these positions are isolated from the rest of the frame. Sync and control busses are shared. Each position is fitted with an MM936 MADI I/O (redundant fiber) for connection to the stagebox and an MM934 MADI I/O (coax) for connection to the console.
Euphonix Modular I/O Configuration Guide Product Data Sheets MM934/MM934opt MADI In/Out Features • interface for MADI coded multi-channel audio signals • MADI receiver and transmitter • extended mode (max 64ch) and high sampling mode (max 32ch at 96kHz) • word length 24 bit • MASTER mode: rack locks to MADI input with no need for an SY982 Sync module MM934opt: • multimode fibre transceiver • input auto-sensing: detects whether signal is present on coaxial or fibre input • parallel output: coaxial and fibr
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/4 MM934/MM934opt MADI In/Out Technical Specifications MADI interface: Standard: Connector: signal level: audio data format: backplane connector: power supply: consumption: dimensions: weight: AES10 (1995) BNC, 75 Ohm, coaxial (MADI in, MADI out), SC x2 (SC Duplex), 62.5/125µm multimode (MM934opt), 1310nm wavelength. One fiber strand per MADI direction 800mV ±10% 24bit, 48kHz = max 64ch 24bit, 96kHz = max 32 ch ref.
Euphonix Modular I/O Configuration Guide Product Data Sheets 3/4 MM934/MM934opt MADI In/Out Working Modes on Standard Sampling Rates (44.1/48kHz) 56ch in 56ch out S1...S32 MM934 IN/OUT ROUTING MADI IN ch1 to ch56 IN/OUT ROUTING MADI IN S32 to S5 MADI OUT MADI OUT MASTER: X SEL0: OFF SEL1: OFF SEL2: ON 56-64: ON 32/32: OFF 16/16: OFF 48/16: OFF S1...S32 MM934 56-64: ON 32/32: OFF 16/16: OFF 48/16: OFF S1...
Euphonix Modular I/O Configuration Guide Product Data Sheets 4/4 MM934/MM934opt MADI In/Out 16ch in / 48ch out MM934 48ch in / 16ch out MM934 S1...
Euphonix Modular I/O Configuration Guide Product Data Sheets 1/3 MM935 MADI In/Out Features • interface for MADI coded multichannel audio signals • MADI receiver and transmitter • BNC 75 ohm • extended mode (max. 64ch’s) and high sampling mode (max.
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/3 MM935 MADI In/Out Technical Specifications MADI interface standard: connection: signal level: audio data format: audio sample rate: backplane connector: consumption: dimensions: weight: ambient: humidity: AES 10 (2003) BNC, 75 ohm 800mV +/-10% 24bit transparent for C- and U-Bit according to AES3 24bit, 48kHz = max. 64 channels 24bit, 96kHz = max. 32 channels ref. to DIN41612, 64pin, a+b, male power supply +5V DC appr.
Euphonix Modular I/O Configuration Guide Product Data Sheets 3/3 MM935 MADI In/Out Remote configuration via web interface: Setting of all configurations, parameters and functions via web browser DEVICE: Setting of “Device Name” Functions: Restart device, Initialize device Backup, Restore (all settings to / from file) displays firmware version SETUP: CHANNEL-MODE: MADI-BYPASS: DECODER: Routing of received MADI-channels to frame buss: set to 56 or 64 audio channel direct loop through the module witho
Euphonix Modular I/O Configuration Guide Product Data Sheets 1/3 MM936 MADI In/Out Features • interface for MADI coded multichannel audio signals • MADI receiver and transmitter • redundant optical input /output connector (1 > 2) • extended mode (max. 64ch’s) and high sampling mode (max.
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/3 MM936 MADI In/Out Technical Specifications MADI interface standard: connection: signal: audio data format: audio sample rate: backplane connector: consumption: dimensions: weight: ambient: humidity: AES 10 (2003) SC duplex x2 / 62.5/125µm multimode fiber. 1310nm 24bit transparent for C- and U-Bit according to AES3 24bit, 48kHz = max. 64 channels 24bit, 96kHz = max. 32 channels ref. to DIN41612, 64pin, a+b, male power supply +5V DC appr.
Euphonix Modular I/O Configuration Guide Product Data Sheets 3/3 MM936 MADI In/Out Remote configuration via web interface: Setting of all configurations, parameters and functions via web browser DEVICE: Setting of “Device Name” Functions: Restart device, Initialize device Backup, Restore (all settings to / from file) displays firmware version SETUP: CHANNEL-MODE: MADI-BYPASS: INPUT SELECT: ERROR-FLAG : DECODER: set to 56 or 64 audio channel direct loop through the module without using the frame buss
Euphonix Modular I/O Configuration Guide Product Data Sheets 1/3 SY982 Sync Features • provides sync for modular I/O frames • internal sync at 44.1, 48, 88.2 or 96kHz • external sync by AES, word clock or video signal • lock indication • redundant sync source with a second SY982 • frame address setting • word clock output operation • turn the front-panel source switch with a small screwdriver to step through all available sync modes: int 44.1, int 48, int 88.
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/3 SY982 Sync Technical Specifications sync interface internal sync: external sync: VIDEO connector: Level: input format: WCLK connector: level: input format: AES connector: Level: input format: general backplane connector: power supply: consumption: dimensions: weight: switchable 44.1, 48, 88.2 or 96kHz, BNC, 75 Ohm, coaxial 0,5 ...
Euphonix Modular I/O Configuration Guide Product Data Sheets 3/3 SY982 Sync Redundant clock sources The SY982 Sync module is the central clocking source for the Modular I/O system. It provides all necessary clocks for proper system operation and can be synchronized internally or externally. A Modular I/O frame can be equipped with a second (redundant) SY982. Both sync modules must be installed in the red “reserved” slots on the rear-plane of the frame.
Euphonix Modular I/O Configuration Guide Product Data Sheets 1/3 SY983 Sync Features • provides sync for modular I/O frames • internal sync at 44.1, 48, 88.
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/3 SY983 Sync Technical Specifications sync interface internal sync: external sync: VIDEO connector: level: switchable 44.1, 48, 96kHz, WCLK connector: level: AES connector: Level: BNC, 75 Ohm, coaxial 0,5 ... 1 Vpp (BB/CS) +/-0,3V (Tri-Level) PAL / NTSC / HDTV 1080i/50/59.94/60 720p/50/59.94/60 1080p/23.98/24/25/29.97/30/50/59.94/60 BNC, 75 Ohm, coaxial TTL-level BNC, 75 Ohm, coaxial 0,5 ...
Euphonix Modular I/O Configuration Guide Product Data Sheets 3/3 SY983 Sync Frame position The SY983 must be installed in one of the red colored fitting rails at the rear of the frame, close to the mains connectors. In the case of Master / Slave operation, both SY983 modules must be place here. Redundant clock sources The SY983 Sync module is the central clocking source for the Modular I/O system.
Euphonix Modular I/O Configuration Guide Product Data Sheets 1/7 FC972 Remote Features • TCP/IP over Ethernet interface • Transparent CAN “tunnel” for remote control software • EuCon / Web interface for set up of system • Front side RJ45 Ethernet connector • Front side RJ45 CAN connector • Front side 9-pin serial connector • Front side init button and status LED • On board CAN bus frame address setting • On board CAN bus termination • On board mode switch Block Diagram CAN bus clock battery + RS232 C
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/7 FC972 Remote Operation • Set the frame address and the CAN termination if necessary / mode switch not used • Reset the FC-972 any time (STATUS LED lights green): press the INIT button • To initialize the FC-972 to factory default settings: When power on or after RESET, the STATUS LED will light yellow after 5 seconds. Now press the INIT button and hold it firmly until the STATUS LED flashes 3 times.
Euphonix Modular I/O Configuration Guide Product Data Sheets 3/7 FC972 Remote Installation Set SW1 (A – D) if necessary (default = off) Set SW2 (DEV0 – 2) for an appropriate CAN frame address (default = off). Set SW2-4 (CAN-TERM) to terminate the CAN bus if required (default = off) Location of label switches on the C8702 module. The default IP address label is located on the “Coldfire” chip of the controller module and on the front panel of the module.
Euphonix Modular I/O Configuration Guide Product Data Sheets 4/7 FC972 Remote Can Buss Termination Can Buss Termination must be done on either the SY982 Sync or FC972 Remote. Lack of termination or double termination may result in communication errors in the system. Software Setup Setting the IP address Each frame controller on a network must have a unique IP, subnet mask and gate way (if necessary). During configuration, FC972 modules are addressed as IP address: 192.168.0.
Euphonix Modular I/O Configuration Guide Product Data Sheets 5/7 FC972 Remote 3. Open a browser and enter the FC-972 default IP address in the URL window (http://xxx.xxx.xxx.xxx). 4. On the FC-972 web site go to “SYSTEM CONFIG” and make the necessary changes.
Euphonix Modular I/O Configuration Guide Product Data Sheets 6/7 FC972 Remote Update of the Controller Firmware The firmware for the FC-972 must be “burned” into the flash memory of the controller. Firmware comes as a zip file (compressed) which contains the firmware image. After download (contact Euphonix), the file must be unzipped (“extracted” on PC) saved to a known directory on the configuration PC. The image will be names “xyz.img” where “xyz” stands for the version number.
Euphonix Modular I/O Configuration Guide Product Data Sheets 7/7 FC972 Remote Technical Specifications Controller module Micro controller: Flash memory: RAM: RTC: OS: MCF8250 “Coldfire” 8 MByte 16 MByte DS 1306 eCos External connectors LAN (RJ45): RS232 (Sub-D / 9pin): CAN (RJ 45): 10/100 Mbit/sec Ethernet Controller serial interface 1 CAN 1.1 (125kBit/sec) INIT: The INIT button is reserved for future applications STATUS LED: The status LED lights yellow for the moment.
Euphonix Modular I/O Configuration Guide Product Data Sheets WC984 4ch WCLK Out Features • sync output module for Modular I/O system • 4x buffered Word Clock outputs • frame sync buss provides the sync source • sync output for sync-to-MADI frames Block Diagram 69 1/2
Euphonix Modular I/O Configuration Guide Product Data Sheets WC984 4ch WCLK Out Specifications WCLK output: Connector: level: output format: following C8000 system clock 44.1 . 96kHz BNC, 75Ohm, coaxial TTL-level Wordclock GENERAL backplane connector: power supply: consumption: dimensions: weight: ref. to DIN41612, 64pin, a+b, male +5V DC appr.
Euphonix Modular I/O Configuration Guide Product Data Sheets AD914 4ch Microphone Input Features • 4ch high quality MIC input • 24bit sigma-delta A/D-converter, sample rate up to 96kHz • digitally controlled gain 0..+65dB • max.
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/2 AD914 4ch Microphone Input Technical Specifications dynamic range max. input level THD+N 110dB (RMS) +20dBu <0.09% @ max. input level digital output: resolution sample rate gain equiv. Input noise @ 200 Ohm 40dB gain 126,5dB (RMS) backplane connector: ref. to DIN41612 64pin, a+b, male power supply +5V DC consumption appr. 1300 mA dimensions 3RU, 4HP, 175mm dept weight ~300g frequency response 10Hz (-3dB)...
Euphonix Modular I/O Configuration Guide Product Data Sheets AD920 4ch Analog Line Input Features • 4ch A/D-converter • 24bit sigma-delta A/D converter • sample rate up to 96kHz • sophisticated circuit design • balanced analog inputs • electrical isolation between channels (floating) Block Diagram 73 1/2
Euphonix Modular I/O Configuration Guide Product Data Sheets AD920 4ch Analog Line Input Specifications resolution sample rate dynamic range 24bit 32...96kHz 113dB (RMS) 116dB (A) THD+N <0.002% @ max. input level frequency response 20Hz...20kHz (FS=48kHz) (+/-0.5dB) 20Hz...40kHz (FS=96kHz) crosstalk >100dB (1kHz) >95dB (20kHz) >85dB (40kHz) max. input level +15...+28dBu @ 0dBFS input impedance 10 kOhm, floating balanced connector XLR, 1-screen, 2-live, 3-return backplane connector ref.
Euphonix Modular I/O Configuration Guide Product Data Sheets DA921 4ch Analog Line Output Features • 4ch D/A-converter • 24bit sigma-delta D/A converter • sample rate up to 96kHz • sophisticated circuit design • balanced analog outputs • electrical isolation between channels (floating) Block Diagram 75 1/2
Euphonix Modular I/O Configuration Guide Product Data Sheets DA921 4ch Analog Line Output Technical Specifications resolution sample rate dynamic range THD+N frequency response (+/-0.5dB) crosstalk max. output level output impedance connector backplane connector power supply consumption dimensions weight: 24bit 32...96kHz 112dB (RMS) 117dB (A) <0.002% @ max. output level 20Hz...20kHz (FS=48kHz) 20Hz...40kHz (FS=96kHz) >110dB (1kHz) >105dB (20kHz) >90dB (40kHz) +15...
Euphonix Modular I/O Configuration Guide Product Data Sheets AD922 4ch Analog Line Input Features • 4ch A/D-converter • 24bit sigma-delta A/D converter • sample rate up to 96kHz • sophisticated circuit design • balanced analog inputs • electrical isolation between channels (floating) Block Diagram 77 1/2
Euphonix Modular I/O Configuration Guide Product Data Sheets AD922 4ch Analog Line Input Specifications resolution sample rate dynamic range 24bit 32...96kHz 113dB (RMS) 116dB (A) THD+N <0.002% @ max. input level frequency response 20Hz...20kHz (FS=48kHz) (+/-0.5dB) 20Hz...40kHz (FS=96kHz) crosstalk >100dB (1kHz) >95dB (20kHz) >85dB (40kHz) max. input level +15...+28dBu @ 0dBFS input impedance 10 kOhm, floating balanced connector 15-pin DSub, female panel backplane connector ref.
Euphonix Modular I/O Configuration Guide Product Data Sheets DA923 4ch Analog Line Output Features • 4ch D/A-converter • 24bit sigma-delta D/A converter • sample rate up to 96kHz • sophisticated circuit design • balanced analog outputs • electrical isolation between channels (floating) Block Diagram 79 1/2
Euphonix Modular I/O Configuration Guide Product Data Sheets DA923 4ch Analog Line Output Technical Specifications resolution sample rate dynamic range THD+N frequency response (+/-0.5dB) crosstalk max. output level output impedance connector backplane connector power supply consumption dimensions weight: 24bit 32...96kHz 112dB (RMS) 117dB (A) <0.002% @ max. output level 20Hz...20kHz (FS=48kHz) 20Hz...40kHz (FS=96kHz) >110dB (1kHz) >105dB (20kHz) >90dB (40kHz) +15...
Euphonix Modular I/O Configuration Guide Product Data Sheets AD924 4ch Microphone Input Features • 4ch high performance mic input • 24bit sigma-delta A/D converter • sample rate up to 96kHz • 142dB dynamic range (greater than conventional preamps) • digital gain setting 0…70dB • digital audio processing (gain, subsonic filter, phase reverse) • sophisticated circuit design • balanced analog inputs • electrical isolation between channels (floating) • 48v phantom power • remote operation via Eucon or web bro
Euphonix Modular I/O Configuration Guide Product Data Sheets AD924 4ch Microphone Input Technical Specifications dynamic range max. input level THD+N equiv. input noise @ 200 Ohm digital output resolution sample rate gain low cut filter frequency response crosstalk CMR input impedance connector backplane connector power supply consumption dimensions weight: 142dB (RMS) +18dBu @ 0dBFS <0.002% @ max. input level 127dB(RMS) 129dB (A) 115dBqp (CCIR) 24 bit 32..
Euphonix Modular I/O Configuration Guide Product Data Sheets DD908 4ch AES In/Out Features • 4ch AES/EBU input/output interface • sample rate up to 96kHz • sophisticated circuit design • XLR input and output at 110Ohm • hardware bypass: relays connect related inputs and outputs if power fails • sample rate converters on inputs Block Diagram 83 1/2
Euphonix Modular I/O Configuration Guide Product Data Sheets DD908 4ch AES In/Out Technical Specifications AES/EBU input format output format resolution sample rate connector level AES professional, AES consumer transparent, same as related input 24bit 32…96kHz XLR, 1-screen, 2-live, 3-return 0,5 … 5 Vpp backplane connector power supply consumption dimensions weight: ref. to DIN41612, 64pin, a+b, male +5V DC appr.
Euphonix Modular I/O Configuration Guide Product Data Sheets 1/2 DD909 8ch AES In Features • 8ch AES/EBU input interface • sample rate up to 96kHz • sophisticated circuit design • XLR inputs at 110Ohm • sample rate converters Block Diagram 85
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/2 DD909 8ch AES In Technical Specifications AES/EBU input format resolution sample rate connector level AES professional, AES consumer 24bit 32…96kHz XLR, 1-screen, 2-live, 3-return 0,5 … 5 Vpp backplane connector power supply consumption dimensions weight ref. to DIN41612, 64pin, a+b, male +5V DC appr.
Euphonix Modular I/O Configuration Guide Product Data Sheets 1/2 DD910 8ch AES Out Features • 8ch AES/EBU output interface • sample rate up to 96kHz, following the system clock • sophisticated circuit design • XLR outputs at 110Ohm Block Diagram 87
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/2 DD910 8ch AES Out Technical Specifications AES/EBU output format resolution sample rate connector level transparent, as connector input 24bit 32…96kHz, following the system clock XLR, 1-screen, 2-live, 3-return 0,5 … 5 Vpp backplane connector power supply consumption dimensions weight ref. to DIN41612, 64pin, a+b, male +5V DC appr.
Euphonix Modular I/O Configuration Guide Product Data Sheets DD911 4ch AES In/Out Features • 4ch AES/EBU input/output interface • sample rate up to 96kHz • sophisticated circuit design • coaxial input and output at 75Ohm • hardware bypass: relays connect related inputs and outputs if power fails • sample rate converters on inputs Block Diagram 89 1/2
Euphonix Modular I/O Configuration Guide Product Data Sheets DD911 4ch AES In/Out Technical Specifications AES/EBU input format output format resolution sample rate connector level AES professional, AES consumer transparent, same as related input 24bit 32…96kHz BNC, 75Ohm, coaxial 0,5 … 5 Vpp backplane connector power supply consumption dimensions weight ref. to DIN41612, 64pin, a+b, male +5V DC appr.
Euphonix Modular I/O Configuration Guide Product Data Sheets 1/2 DD912 8ch AES In Features • 8ch AES/EBU input interface • sample rate up to 96kHz • sophisticated circuit design • coaxial input at 75Ohm • sample rate converters Block Diagram 91
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/2 DD912 8ch AES In Technical Specifications AES/EBU input format resolution sample rate connector level AES professional, AES consumer 24bit 32…96kHz BNC, 75Ohm, coaxial 0,5 … 5 Vpp backplane connector power supply consumption dimensions weight ref. to DIN41612, 64pin, a+b, male +5V DC appr.
Euphonix Modular I/O Configuration Guide Product Data Sheets 1/2 DD913 8ch AES Out Features • 8ch AES/EBU output interface • sample rate up to 96kHz, following the system clock • sophisticated circuit design • coaxial input at 75Ohm Block Diagram 93
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/2 DD913 8ch AES Out Technical Specifications AES/EBU output format resolution sample rate connector level transparent, as connector input 24bit 32…96kHz, following the system clock BNC, 75Ohm, coaxial 0,5 … 5 Vpp backplane connector power supply consumption dimensions weight ref. to DIN41612, 64pin, a+b, male +5V DC appr.
Euphonix Modular I/O Configuration Guide Product Data Sheets DE901 Dolby D/E Decoder Features • (N/A at time of writing) Block Diagram (N/A at time of writing) 95 1/2
Euphonix Modular I/O Configuration Guide Product Data Sheets DE901 Dolby D/E Decoder Technical Specifications (N/A at time of writing) Installation (N/A at time of writing) 96 2/2
Euphonix Modular I/O Configuration Guide Product Data Sheets DE911 Dolby E Encoder Features • (N/A at time of writing) Block Diagram (N/A at time of writing) 97 1/2
Euphonix Modular I/O Configuration Guide Product Data Sheets DE911 Dolby E Encoder Technical Specifications (N/A at time of writing) Installation (N/A at time of writing) 98 2/2
Euphonix Modular I/O Configuration Guide Product Data Sheets DE912 Dolby D+ Encoder Features • (N/A at time of writing) Block Diagram (N/A at time of writing) 99 1/2
Euphonix Modular I/O Configuration Guide Product Data Sheets DE912 Dolby D+ Encoder Technical Specifications (N/A at time of writing) Installation (N/A at time of writing) 100 2/2
Euphonix Modular I/O Configuration Guide Product Data Sheets SD941 4ch SD De/Embedder Features • interface for embedded audio in SDI signals (270MB/s) • 4ch embedder/deembedder • audio group selection • channel swap (1<>2; 3<>4) • pair swap (1/2<>3/4) • MASTER mode: system can lock to SDI input • pack mode: highest density of 16 embedded audio channels • cascade function for insertion of more than one audio group into one SDI signal Block Diagram 101 1/4
Euphonix Modular I/O Configuration Guide Product Data Sheets 2/4 SD941 4ch SD De/Embedder Technical Specifications SDI interface with Audio Embedder/Deembedder function standard: connection: signal level: equalisation: audio data format: backplane connector: power supply: consumption: dimensions : weight : SMPTE 272 M - AB, 270Mb/s, 525/625 component BNC, 75 Ohm, coaxial (SDI through: active loop, reclocked) 800mV ±10% appr. to 180m (Belden) 20bit ref. to DIN41612, 64pin, a+b, male +5V DC appr.
Euphonix Modular I/O Configuration Guide Product Data Sheets SD941 4ch SD De/Embedder 3/4 CASCADE -generates a new audio group as selected (TX group) within existing frame structure. This overwrites all data of this group if it was already embedded previously. -necessary if a new group should be embedded and if audio in other groups was embedded previously -matches the structure which was generated by PACK mode.
Euphonix Modular I/O Configuration Guide Product Data Sheets SD941 4ch SD De/Embedder 4/4 BYPASS -Connects the SDI Out directly to the SDI In bypassing the Embedder MASTER -Allows the SD941 to be used as the frame’s master sync source. Clock is derived from the module’s SDI Input. The module must be installed in one of the four reserved slots on the rear-plane. An SY982 Sync module should not be installed simultaneously in the frame. .
Euphonix Modular I/O Configuration Guide Product Data Sheets 1/4 SD942 8ch SD De/Embedder Features • interface for embedded audio in SDI signals (270MB/s) • 8ch embedder/deembedder • 2 SDI outputs • bypass relay for SDI IN >>> SDI OUT1 • bit transparent for coded data streams (e.g.
Euphonix Modular I/O Configuration Guide Product Data Sheets SD942 8ch SD De/Embedder 2/4 Technical Specifications VIDEO : standard: connection: signal level: equalisation: return loss: SMPTE 272 M–A, C 270 Mbit SD-SDI BNC, 75 Ohm, coaxial (SDI through: active loop, reclocked) 800mV ±10% 130m (Belden 1694A, 1.485GHz) 300m (Belden 8281 , 270 MHz) >15 dB (1.485 GHz) supported video standards: SD 525/59.
Euphonix Modular I/O Configuration Guide Product Data Sheets SD942 8ch SD De/Embedder 3/4 Installation MASTER MODE -When ON, the SD942 is clock master for the frame (this master module must be inserted in to one of the reserved slots in the rear-plane SD-mode: 48 kHz audio clock is locked to 270 Mbit video carrier Pattern Generator-mode: 48 kHz is locked to the video carrier REMOTE / LOCAL -In LOCAL mode, the DIP switch settings are valid on power up.
Euphonix Modular I/O Configuration Guide Product Data Sheets SD942 8ch SD De/Embedder 4/4 -In REMOTE mode, local DIP switch settings are not valid. The module must be in REMOTE mode to be configured via web browser interface. BUS-EN **see also Initial Setup / Buss Assignment -when OFF, disconnects the outputs to the audio backplane busses on power up -when ON, connects the outputs to the audio backplane busses on power up Note: This mode is most useful in initial module setup.
Euphonix Modular I/O Configuration Guide Product Data Sheets HD943 8ch HD/SD De/Embedder Features • multi-format HD/SD operation with auto-detection • 8ch embedder/deembedder • 2 SDI outputs • bypass relay for SDI IN >>> SDI OUT1 • bit transparent for coded data streams (e.g.
Euphonix Modular I/O Configuration Guide Product Data Sheets HD943 8ch HD/SD De/Embedder 2/4 Technical Specifications VIDEO : standard: connection: signal level: equalisation: return loss: SMPTE 299M 1,485 Gbit HD-SDI SMPTE 272 M–A, C 270 Mbit SD-SDI BNC, 75 Ohm, coaxial (SDI through: active loop, reclocked) 800mV ±10% 130m (Belden 1694A, 1.485GHz) 300m (Belden 8281 , 270 MHz) >15 dB (1.
Euphonix Modular I/O Configuration Guide Product Data Sheets HD943 8ch HD/SD De/Embedder 3/4 Installation MASTER MODE -When ON, the HD943 is clock master for the frame (this master module must be inserted in to one of the reserved slots in the rear-plane SD-mode: 48 kHz audio clock is locked to 270 Mbit video carrier Pattern Generator-mode: 48 kHz is locked to the video carrier REMOTE / LOCAL -In LOCAL mode, the DIP switch settings are valid on power up.
Euphonix Modular I/O Configuration Guide Product Data Sheets HD943 8ch HD/SD De/Embedder 4/4 -In REMOTE mode, local DIP switch settings are not valid. The module must be in REMOTE mode to be configured via web browser interface. BUS-EN **see also Initial Setup / Buss Assignment -when OFF, disconnects the outputs to the audio backplane busses on power up -when ON, connects the outputs to the audio backplane busses on power up Note: This mode is most useful in initial module setup.
